Taft Sanitary Engineering Center, the Laboratory has contributed to the establishment of Cincinnati among the nation's leading centers of industrial health research.

Move the probe along the interface periphery while observing the instrument readout If an increased mater leading is observed, slowly probe the interface where leakage is Indicated until the maximum meter reading it obtained.

The following formulation illustrates the use of Aroclor 1232 in a joint-sealer formulation: JOINT-SEALANT COMPOUND FOR CURTAIN-WALL CONSTRUCTION Ingredients Parts by Weight Tkiokol LP-32 polysulfide Phenolic resin Aroclor 1232 Calcium carbonate Titanium dioxide Stearic acid Sulfur 100 5 5-15 40 10 1 0.1 C-5 paste (lead peroxide, 50%; dibutyl phthalate, 45%; stearic acid, 5%: passed three times through a tight paint mill

This data sheet gives information on the polyphenylene prepolymer 1711 which is the basic component for crosslinking or chain extension and leading to high molecular weight, infusible polyphenylene resin.

T'* Manual Trans 0"TDC '* W/R46SK plugs 080" gap W/Disl. 1103208 16&( 1100 Contact Gap 5ATGC w/rubber plug instal'ed 46 Canada w;leaded *uel 5**^ 700 Canada w/luaded fuel 3',@,7U0 n Pick-up coil gap FIRING OROER 1 -- 1,2,7.8,4,5,6 3 2-1,4.2.5,3.6 3-1.8,4,3.6.5,7.2 4--1,8.7,3,6,5.4.2 5-1.5,3,6,2,4 6 - 1.54,8.6,3.7.2 7-1,3,4.2 8-1.5,4,2.6.3,7,8 9- 1.4.5,2,3.6 10-1.6.5 4,3,7 li - 1,8.7,2,6,5.4,3 12-1.5.6.3,4,2,7.8 13- 1.3.7 7.6.5,4,8 14 -- 1,2.4.3 A Right bank EVEN numbers Left bankODO numbers B Right bank ODD numbers Left bank EVEN numbers C Right bank numbers 1-4 left bank numbers5-8 D Right bank numbers 1-3 left bank number$4-6 Names and numbers other than Echlm and Visumatic as used m this or any other Echlin literature are used for reference purposes only. <1978 THE ECHLiN MANUFACTURING CO. 2

On a mechanical basis, spicules may abrade the skin leading to superficial and transitory irritation.

Designs based on number of air changes per hour, or other rule-of-thumb methods, are hopelessly inadequate, and lead either to unsuccessful opera tion or to excessive and unnecessarily high cost'of installation. 1.

This reduced the drying tempera ture and increased the airflow rate to prevent burning of the ; EftlTiplftElectrical meters have been applied to some extent on forage crops; however, the extreme variability of.the moisture and density of the material tested leads to great variability in the readings obtained.

--A short L. defines fine particle sizes and types and gives a general survey 1 biography is given of Professor Toropov, leading Soviet chemist of their intrinsic or definitive, application, and functional proper working in the field of silicate chemistry, ferrites, cement, etc.

494 CHAPTER 33 1960 Guide than lost heat.

Pro vision must be made to prevent water from freezing in the tank, the tank vent, and the pipe leading to the tank.

This unit will provide a means of developing the high density asbestos formulations and provide engineering and manu facturing information leading to the design of a production sized cslandering unit. 1- - MICH08486 b) High Temperature Millboard - Lehr Discs - Research is actively working on the development of a high temperature product.

Pittsburgh Pa London Ont Ass't Chief Engineer Chief Surgeon Toronto Ont a Lead South Dakota Underground Superintendent Medical Director Elliot Lake Ontario Timmins Ontario Fellow in Pharmacology Ass't Prof. of Clinical Medicine Toronto Ont Philadelphia Pa Vice President- Operations Operations Toronto Ont Head Dept. of Cleveland Pulmonary Diseases Ohio F 00000001659 .

Garrett would lead to the conclusion that all four men had experienced only a minimal exposure, that the re moval of the men from the area was unnecessary, and that there would be no permanent effects as a result of this exposure.

Macaulay National Lead Company Wyandotte Chemicals Corporation Chairman G.