Document zoKoNEzdL8p8bO2qKv3n6bJpa

, ABERDEEN PVC PLANT NEW EMPLOYEE SAFETY ORIENTATION - TRAINING CHECKLIST (1) < (2) ABERDEEN SAFETY ORIENTATION SHOW HEALTH SHOWS: VCM LEAD TOSCA 0) _ iik) * (5) SAFETY RULE BOOKS: CONOCO ABERDEEN DuPONT SAFETY ORIENTATION (#500) LIFTING: NSC BOOKLET DISCUSSION < (6) FORKLIFT TRAINING: SHOW FIELD (7) < (8) (9) X (10) ELECTRICAL LOCKOUT: ALLIED CHEMICAL FILM REVIEW OF ABERDEEN LOCKOUT PROCEDURE RESPIRATOR TRAINING: SCOTT AIR PACK FRESH AIR EQUIPMENT ENTRY: DUST ** &/R' nr? CHARTER OIL FILM REVIEW OF ABERDEEN ENTRY PROCEDURE PICTURES TAKEN (11) (12) SAFETY EQUIPMENT ISSUED ALL QUIZ SHEETS CORRECTED AND: ATTACHED ... (13) INTRODUCTION TO PLANT MED I CAE 4 (1) (2) (3) (A) <5) (6) 11/80 AHS T TRAINEES (10) * __________ (12) _______________________ / DATE: I( -- / 5 ^ ^ /~Y^ - Sr/ VAB.0001076459 > 1 flu.e NAME c' faa/ -TEST. DEPARTMENT /- /j- W DATE A 1 Excessive amounts of lead in the body can cause serious harm, including death. True False The lead materials we have in this plant are powders used as heat stabilizers and color pigments in PVC compounds. True False . c The exposure limit for lead is SA micrograms of lead per cubic meter of air for any eight-hour work period. 4 The exposure limit for lead is lowered if you work more than eight (S) hours during a work period. True False Lead used in this plant can enter the body by: A. Innaling B. Swallowing C. Absorbing through the skin All of the above A 5 B Only V m 6 If you get lead material on your skin or clothing, you don't have to do anything about it because lead is not absorbed through your skin. True False NOTE: If you think that was a ''trick" question, you should think about *vour answer a0gain. ** i Some lead tasks require breathing protection. Name one such task .8 It is O.K. to take food, drinks, etc. into lead areas, provided you are careful to not let lead materials get into them. T rue False 9. Medical testing is used to make certain your lead exposure is not hurting you True False 10. If the lead area ventilation systems are working and your medical tests and monitoring results are all "Good," you don't have to be concerned b 4 +* >L -J NOTE: j rue False VAB.0001076460 If you're not sure about your answer, you need to think about it Oine more. A VCM EXPOSURE TRAINING -TEST, 1980- t NAME DEPARTMENT DATE Evidence has been found that exposure to high-level concentrations of VCM over long periods of time could cause cancer of the liver. True (False ( ) . * A finger bone disease, acraosteolyis ("AOL"), has been linked to the manual cleaning of PVC reactors. True(/V) False( ) 3. Liquid VCM can cause severe frostbite. True False ( ) 4. The exposure limits for VCM are _____ / ppm average for any eight hour period and ppm for any 15 minute period. 5. The three VCM regulated areas in the plant are: A. {Z) Dry blend basement, Q.C. Lab and the Plasticizer Tank Farm. Plasticizer Building, Boiler House and the East Warehouse. VCM Tank Farm and the two large reactor areas. 6. If you have no business in a VCM regulated area, you must stay out. True (^5^ False ( ) 7. Respiratory equipment (gas mask, air-line respirators, Scott Air- Pack, etc.) is required above (but not below): / ((A>) 1.0 ppm (B) 0.5*ppm (C) 10.0 ppm i Our Honeywell continuous monitors alarm when ______ / in an area. We monitor your VCM exposure to: ppm is detected n s Minimize your exposure to VCM. Monitor progress in reducing VCM concentrations. Both A & B. To make sure we have a record. Protective clothing is required for certain jobs. True False ( ) VAB.0001076461 11 4 M VCM EXPOSURE TRAINING -TEST, 1980- f NAME DEPARTMENT 1. Evidence has been found that exposure to high-level concentrations of VCM over long periods of time could cause cancer of the liver. yi True(c/) False( ) 2. A finger bone disease, acraosteolyis ("AOL"), has been linked to the manual cleaning of PVC reactors. True( w') False( ) 3. Liquid VCM can cause severe frostbite. / True({/) False ( ) 4. The exposure limits for VCM are ppm average for any eight hour period and ppm for Shy Id minute period. 5. The three VCM regulated areas in the plant are: A. Dry blend basement, Q.C. Lab and the Plasticizer Tank Farm. B. Plasticizer Building, Boiler House and the East Warehouse. ClT?) VCM Tank Farm and the two large reactor areas. 6. If you have no business in a VCM regulated area, you must stay out. p True (l/) False ( ) 7. Respiratory equipment (gas mask, air-line respirators, Scott AirPack, etc.) is required above (but not below): (A), 1.0 ppm (B) 0.5sppm (C) 10.0 ppm * j 8. Our Honeywell continuous monitors alarm when / ppm is detected in an area. 9. We monitor your VCM exposure to: A. B,, ''"CT.) D. Minimize your exposure to VCM. Monitor progress in reducing VCM concentrations. Both A & B. To make sure we have a record. 10. Protective clothing is required for certain jobs. TrueQ/O False ( ) VAB.0001076462 p j 1 N'AMii r \ DEPARTNENT tA 1. Excessive amounts of lead in the body can cause serious harm, including death. True j / False ? The lead materials we have in this plant are powders used as heat stabilizers and color pigments in PVC compounds. ./ True False o. The exposure limit for lead is micrograms of lead per cubic meter of air for any eight-hour work period. 4. The exposure limit for lead is lowered if you work more than eight (S) hours during a work period. True False b. Lead used in this plant can enter the body by: A. Inhaling B. Swallowing C. Absorbing through the skin D. All of the above AS B Only 6 If you get lead material on your skin or clothing, you don't have to do an*vthingO about it because lead is not absorbed throug^h #your skin. True False NOTE: If vou think that was a ''trick" question, you should think about v# our answer aogain. / V* Some lead tasks require breathing protection. Namte .one such task. ^ v vv/ 8. food, drinks, etc. into lead areas, provided you are careful to not let lead materials get into them. T rue False 9 Medical testing is used to make certain your lead exposure is not hurting you True False 10. If the lead area ventilation systems are working and your medical tests and monitoring results are all "Good," you don't have to be concerned * L* , V* .i : * * '~p c N01TI: T rue False VAB.0001076463 If vou're not sure about your answer, you need to think about it some more. -TEST, 19#>- A V m NA> DEPARTMENT DATE 1. Excessive amounts of lead in the body can cause serious harm, including death. True False The lead materials we have in this plant are powders used as heat stabilizers and color pigments in PVC compounds. True False o. The exposure limit for lead is micrograms of lead per cubic meter of air for any eight-hour work period. 4. The exposure limit for lead is lowered if you work more than eight (S) hours during a work period. True False Lead used in this plant can enter the body by: A. Inhaling B. Swallowing C. Absorbing through the skin All of the above A & B Only 6 If you get lead material on your skin or clothing, you don't have to do anything about it because lead is not absorbed through your skin. True False NOTE: If you think that was a "trick" question, you should think about vour answer again. Some lead tasks require breathing nrotection. Name one such task. 8 It is O.K. to take food, drinks, etc. into lead areas, provided you are careful to not let lead materials get into them. T rue False 9 Medical testing is used to make certain your lead exposure is not hurting you. X-True False 10 If the lead area ventilation systems are working and your medical tests and monitoring results are all "Good," vou don't have to be concerned ^* * .* > i ^ * +- c t NOIL:: T rue False If vou're not sure about your answer, you need to think about it VAB.0001076464 some more. mmm VCM EXPOSURE TRAINING -TEST, 1980- / DEPARTMENT DATE 1. Evidence has been found that exposure to high-level concentrations of VCM over long periods of time could cause cancer of the liver. TrueCX^) False ( ) 2. A finger bone disease, acraosteolyis ("AOL."), has been linked to the manual cleaning of PVC redactors. Tru efjfk^)/ False ( ) 3. Liquid VCM can cause severe/frostbite. True(JX^) False ( ) 4. The exposure limits VCM are _____ ) ppm average for any eight hour period and ____ S-- ppm for any 15 minute period. 5. The three VCM regulated areas in the plant are: (A^) Dry blend basement, Q.C. Lab and the Plasticizer Tank Farm. b7 Plasticizer Building, Boiler House and the East Warehouse. C. VCM Tank Farm and the two large reactor areas. 6. If you have no business in a VCM regulated area, you must stay out. True(^Q False( ) 7. Respiratory equipment (gas mask, air-line respirators, Scott AirPack, etc.) is required above (but not below): A)) 1.0 ppm (B) 0.5vppm (C) 10.0 ppm 8. Our Honeywell continuous monitors alarm when in an area. / ppm is detected 9. We monitor your VCM exposure to: Minimize your exposure to VCM. Monitor progress in reducing VCM concentrations. Both A & B. To make sure we have a record. 10. Protective clothing is required for certain jobs. True(/^ ) False( ) VAB.0001076465 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION I QUIZ 1. Good, competent, professional forklift operation is a safe operation and you can never be too experienced to learn more about safety. X X X 2. The first rule of safe forklift operation is to know the capacity of your truck. 3. The load capacity of each of our forklift trucks is clearly marked on the identification plate on the truck. 4. If you are in doubt about your forklift's ability to pick up a certain load, use the trial and error approach. 5. A pre-work check of your forklift should be made to be sure it's working right and will operate safely. 6. The further the center of the load is away from the front of the carriage, the larger the load you can pick up. F 7. All of the forklift trucks in the Aberdeen Plant are equipped with a hand brake. 8. You should try to repair any problems you find during the pre-work check of the forklift truck. & VAB.0001076466 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION II QUIZ A forklift truck steers with its rear wheels, not its front wheels like your car. When you are planning to make a turn while traveling forward, you should steer your forklift to the opposite side of the road or isle...in the direction you are going to turn. When traveling backward, the rear wheels should pass the comer and the front wheels should reach the corner before you start turning the steering wheel to make a turn. A forklift truck operator must always watch the rear swing of the truck as well as the front swing of the load. A forklift truck is much harder to steer when the forks are loaded. A forklift truck operator should always travel with the forks four to six inches above the ground. An operator should always inspect a load before he attempts to make a lift. When picking up a load with a forklift truck, always approach the load squarely. The forks should be spaced as widely as possible according to the load width and equally spaced form the sides of the carrigae. At times, it might become necessary to make a lift with only one fork. * At times, it might also become necessary to "pick up short", that is pick up a load with only part of your forks. An operator should never put his head, hands or feet out of the truck cage. Only the small Hyster forklift should ever be carried in the plant's elevators. It is better to drive forward up a ramp when your truck is empty. You should drive forward up a ramp and backwards down a ramp when your forks are loaded. SECTION II QUIZ ^ 16. Always cross railroad tracks at a 45 degree angle. 17. Passengers should never be carried on a forklift truck as it is designed for only one person...the operator. Before depositing a load, the operator should take the time to inspect the place where he is going to unload. r 19. You should never use full back tilt when high stacking. The safest condition is when the top of the mast is only a foot to 18 inches back from vertical. If you have to leave the fork truck unattended for even a short time, you should lower the forks and turn off the engine. VAB.0001076468 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION III QUIZ 1. If the tractor is attached to the trailer, you should be sure to notify the driver that you are about to begin loading the trailer. 2. It is not necessary to chock the wheels of a trailer to be loaded if the tractor is attached. K 3. In addition to the dolly wheels, special jacks must be placed under the front of a trailer, when the tractor is not attached, before loading begins. 4. Trailer floors should be checked for damage before loading begins. 5. The proper way to load a trailer is to load all of one side then all of the other side. P 6. If double stacking is required when loading a trailer, it should be done in the front and back so the extra weight will be on the axles. 7. An employee should never be lifted with a forklift truck unless a caged worklift is used. 8. When using a worklift, you must be sure that the safety pin is placed through the worklift moynt and the forklift forks to prevent the worklift from sliding off the forks. 9. It is O.K. for an employee to ride to a work site if he is riding in a worklift. 10. Unloading a trash dumpster should be done with forklift mast straight up, not tilted forward or backward. VAB.0001076469 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION I QUIZ H- Good, competent, professional forklift operation is a safe operation and you can never be too experienced to learn more about safety. .2 The first rple of safe forklift operation is to know the capacity of your truck. 3. The load capacity of each of our forklift trucks is clearly marked on the identification plate on the truck. If you are in doubt about your forklift's ability to pick up a certain load, use the trial and error approach. 5. A pre-work check of your forklift should be made to be sure it's working right and will operate safely. 6. The further the center of the load is away from the front of the carriage, the larger the load you can pick up. r 7. All of the forklift trucks in the Aberdeen Plant are equipped with a hand brake. You should try to repair any problems you find during the pre-work check of the forklift truck. & VAB.0001076470 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION II QUIZ A forklift truck steers with its rear wheels, not its front wheels like your car. When you are planning to make a turn while traveling forward, you should steer your forklift to the opposite side of the road or isle...in the direction you are going to turn. When traveling backward, the rear wheels should pass the corner and the front wheels should reach the corner before you start turning the steering wheel to make a turn. A forklift truck operator must always watch the rear swing of the truck as well as the front swing of the load. A forklift truck is much harder to steer when the forks are loaded. A forklift truck operator should always travel with the forks four to six inches above the ground. 7. An operator should always inspect a load before he attempts to make a lift. 8. When picking up a load with a forklift truck, always approach the load squarely. 9. The forks should be spaced as widely as possible according to the load width and equally spaced form the sides of the carrigae. .10 At times, it might become necessary to make a lift with only one fork. * .11 At times, it might also become necessary to ''pick up short", that is pick up a load with only part of your forks. .12 An operator should never put his head, hands or feet out of the truck cage. Only the small Hyster forklift should ever be carried in the plant's elevators. It is better to drive forward up a ramp when your truck is empty. You should drive forward up a ramp and backwards down a ramp when your forks are loaded. J VAB.0001076471 SECTION II QUIZ 1 4 16. Always cross railroad tracks at a 45 degree angle. 17. Passengers should never be carried on a forklift truck as it is designed for only one person...the operator. 18. Before depositing a load, the operator should take the time to inspect the place where he is going to unload. 19. You should never use full back tilt when high stacking. The safest condition is when the top of the mast is only a foot to 18 inches back from vertical. 20. If you have to leave the fork truck unattended for even a short time, you should lower the forks and turn off the engine. 'i VAB.0001076472 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION III QUIZ 1. If the tractor is attached to the trailer, you should be sure to notify the driver that you are about to begin loading the trailer. in 2. It is not necessary to chock the wheels of a trailer to be loaded if the tractor is attached. t;- i 3. In addition to the dolly wheels, special jacks must be placed under the front of a trailer, when the tractor is not attached, before loading begins. 4. Trailer floors should be checked for damage before loading begins. 5. The proper way to load a trailer is to load all of one side then all of the other side. T 6. If double stacking is required when loading a trailer, it should be done in the front and back so the extra weight will be on the axles. 7. An employee should never be lifted with a forklift truck unless a caged worklift is used. 8. When using a worklift, you must be sure that the safety pin is placed through the worklift mount and the forklift forks to prevent the work lift from sliding off the forks. It is O.K. for an employee to ride to a work site if he is riding in a worklift. 10. Unloading a trash dumpster should be done with forklift mast straight up, not tilted forward or backward. I VAB.0001076473 4 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION I QUIZ y /<f/ 1 Good, competent, professional forklift operation is a safe operation and you can never be too experienced to learn more about safety. The first rule of safe forklift operation is to know the capacity of your truck. The load capacity of each of our forklift trucks is clearly marked on the identification plate on the truck. If you are in doubt about your forkliftTs ability to pick up a certain load, use the trial and error approach. A pre-work check of your forklift should be made to be sure it's working right and will operate safely. The further the center of the load is away from the front of the carriage, the larger the load you can pick up. All of the forklift trucks in the Aberdeen Plant are equipped with a hand brake. / r 8* You should try to repair any problems you find during the pre-work check of the forklift truck. VAB.0001076474 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION II QUIZ A forklift truck steers with its rear wheels, not its front wheels like your car. When you are planning to make a turn while traveling forward, you should steer your forklift to the opposite side of the road or" isle...in the direction you are going to turn. When traveling backward, the rear wheels should pass the comer and the front wheels should reach the corner before you start turning the steering wheel to make a turn. A forklift truck operator must always watch the rear swing of the truck as well as the front swing of the load. A forklift truck is much harder to steer when the forks are loaded. A forklift truck operator should always travel with the forks four to six inches above the ground. An operator should always inspect a load before he attempts to make a lift. When picking up a load with a forklift truck, always approach the load squarely. The forks should be spaced as widely as possible according to the load width and equally spaced form the sides of the carrigae. h At times, it might become necessary to make a lift with only one fork. 4 At times, it might also become necessary to ''pick up short", that is pick up a load with only part of your forks. An operator should never put his head, hands or feet out of the truck cage. Only the small Hyster forklift should ever be carried in the plant's elevators. It is better to drive forward up a ramp when your truck is empty. k 15. You should drive forward up a ramp and backwards down a ramp when your forks are loaded. VAB.0001076475 SECTION II QUIZ 16. Always cross railroad tracks at a 45 degree angle. 17. Passengers should never be carried on a forklift truck as it is designed for only one person...the operator. 18. Before depositing a load, the operator should take the time to inspect the place where he is going to unload. 19. You should never use full back tilt when high stacking. The safest condition is when the top of the mast is only a foot to 18 inches back from vertical. 20. If you have to leave the fork truck unattended for even a short time, you should lower the forks and turn off the engine. VAB.0001076476 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION III QUIZ If the tractor is attached to the trailer, you should be sure to notify the driver that you are about to begin loading the trailer. It is not necessary to chock the wheels of a trailer to be loaded if the tractor is attached. In addition to the dolly wheels, special jacks must be placed under the front of a trailer, when the tractor is not attached, before loading begins. Trailer floors should be checked for damage before loading begins. The proper way to load a trailer is to load all of one side then all of the other side. If double stacking is required when loading a trailer, it should be done in the front and back so the extra weight will be on the axles. An employee should never be lifted with a forklift truck unless a caged worklift is used. When using a worklift, you must be sure that the safety pin is placed through the worklift mount and the forklift forks to prevent the work lift from sliding off the forks. It is O.K. for an employee to ride to a work site if he is riding in a worklift. Unloading a trash dumpster should be done with forklift mast straight up, not tilted forward or backward. * VAB.0001076477 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION I QUIZ Good, competent, professional forklift operation is a safe operation and you can never be too experienced to learn more about safety. The first rule of safe forklift operation is to know the capacity of your truck. F The load capacity of each of our forklift trucks is clearly marked on the identification plate on the truck. If you are in doubt about your forklift's ability to pick up a certain load, use the trial and error approach. A pre-work check of your forklift should be made to be sure it's working right and will operate safely. The further the center of the load is away from the front of the carriage, the larger the load you can pick up. All of the forklift trucks in the Aberdeen Plant are equipped with a hand brake. You should try to repair any problems you find during the pre-work check of the forklift truck. VAB.0001076478 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION II QUIZ T 1. A forklift truck steers with its rear wheels, not its front wheels like your car. F 2. When you are planning to make a turn while traveling forward, you should steer your forklift to the opposite side of the road or' isle...in the direction you are going to turn. T 3. When traveling backward, the rear wheels should pass the corner and f the front wheels should reach the comer before you start turning the steering wheel to make a turn. T 4. A forklift truck operator must always watch the rear swing of the truck as well as the front swing of the load. F 5. A forklift truck is much harder to steer when the forks are loaded. T 6. A forklift truck operator should always travel with the forks four to six inches above the ground. T 7. An operator should always inspect a load before he attempts to make a lift. T 8. When picking up a load with a forklift truck, always approach the load squarely. r 9. The forks should be spaced as widely as possible according to the load width and equally spaced form the sides of the carrigae. F 10. fT 11. At times, it might become necessary to make a lift with only one fork. * At times, it might also become necessary to "pick up short", that is pick up a load with only part of your forks. 7 12. An operator should never put his head, hands or feet out of the truck cage. T 13. Only the small Hyster forklift should ever be carried in the plant's elevators. F 14. T 15. It is better to drive forward up a ramp when your truck is empty. You should drive forward up a ramp and backwards down a ramp when your forks are loaded. VAB.0001076479 V SECTION II QUIZ 4 / 16. Always cross railroad tracks at a 45 degree angle. _ZLT 18. Passengers should never be carried on a forklift truck as it is designed for only one person...the operator. Before depositing a load, the operator should take the time to inspect the place where he is going to unload. T 19. T 20. You should never use full back tilt when high stacking. The safest condition is when the top of the mast is only a foot to 18 inches back from vertical. If you have to leave the fork truck unattended for even a short time, you should lower the forks and turn off the engine. * VAB.0001076480 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION III QUIZ If the tractor is attached to the trailer, you should be sure to notify the driver that you are about to begin loading the trailer. It is not necessary to chock the wheels of a trailer to be loaded if the tractor is attached. H. In addition to the dolly wheels, special jacks must be placed under the front of a trailer, when the tractor is not attached, before loading begins. + Trailer floors should be checked for damage before loading begins. The proper way to load a trailer is to load all of one side then all of the other side. If double stacking is required when loading a trailer, it should be done in the front and back so the extra weight will be on the axles. An employee should never be lifted with a forklift truck unless a caged worklift is used. When using a worklift, you must be sure that the safety pin is placed through the worklift mount and the forklift forks to prevent the work lift from sliding off the forks. It is O.K. for an employee to ride to a work site if he is riding in a worklift. Unloading a trash dumpster should be done with forklift mast straight up, not tilted forward or backward. VAB.0001076481 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION I QUIZ Good, competent, professional forklift operation is a safe operation and you can never be too experienced to learn more about safety. The first rule of safe forklift operation is to know the capacity of your truck. The load capacity of each of our forklift trucks is clearly marked on the identification plate on the truck. If you are in doubt about your forklift's ability to pick up a certain load, use the trial and error approach. A pre-work check of your forklift should be made to be sure it's working right and will operate safely. The further the center of the load is away from the front of the carriage, the larger the load you can pick up. All of the forklift trucks in the Aberdeen Plant are equipped with a hand brake. You should try to repair any problems you find during the pre-work check of the forklift truck. & * VAB.0001076482 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION II QUIZ 1. A forklift truck steers with its rear wheels, not its front wheels like your car. 2. When you are planning to make a turn while traveling forward, you should steer your forklift to the opposite side of the road or isle...in the direction you are going to turn. / 3. When traveling backward, the rear wheels should pass the comer and the front wheels should reach the corner before you start turning the steering wheel to make a turn. 4. A forklift truck operator must always watch the rear swing of the truck as well as the front swing of the load. 5. A forklift truck is much harder to steer when the forks are loaded. 6. A forklift truck operator should always travel with the forks four to six inches above the ground. 7. An operator should always inspect a load before he attempts to make a lift. When picking up a load with a forklift truck, always approach the load squarely. The forks should be spaced as widely as possible according to the load width and equally spaced form the sides of the carrigae. At times, it might become necessary to make a lift with only one fork. % At times, it might also become necessary to "pick up short", that is pick up a load with only part of your forks. An operator should never put his head, hands or feet out of the truck cage. 13. Only the small Hyster forklift should ever be carried in the plant's elevators. It is better to drive forward up a rdftip when your truck is empty. You should drive forward up a ramp and backwards down a ramp when your forks are loaded. 7 VAB.0001076483 -4 4 SECTION II QUIZ 4 Always cross railroad tracks at a 45 degree angle. Passengers should never be carried on a forklift truck as it is designed for only one person...the operator. Before depositing a load, the operator should take the time to inspect the place where he is going to unload. . You should never use full back tilt when high stacking. The safest condition is when the top of the mast is only a foot to 18 inches back from vertical. If you have to leave the fork truck unattended for even a short time, you should lower the forks and turn off the engine. 4W * VAB.0001076484 ABERDEEN FORKLIFT TRAINING PROGRAM SECTION III QUIZ 1. If the tractor is attached to the trailer, you should be sure to notify the driver that you are about to begin loading the trailer. j_ 2. It is not necessary to chock the wheels of a trailer to be loaded if the tractor is attached. 3. In addition to the dolly wheels, special jacks must be placed under the front of a trailer, when the tractor is not attached, before loading begins. 4. Trailer floors should be checked for damage before loading begins. 5. The proper way to load a trailer is to load all of one side then all of the other side. If double stacking is required when loading a trailer, it should be done in the front and back so the extra weight will be on the axles. j An employee should never be lifted with a forklift truck unless a caged worklift is used. When using a worklift, you must be sure that the safety pin is placed through the worklift mount and the forklift forks to prevent the work lift from sliding off the forks. It is O.K. for an employee to ride to a work site if he is riding in a worklift. .10 Unloading a trash dumpster should be done with forklift mast straight up, not tilted forward or backward. VAB.0001076485