Document zo6Mxk1wo8zm0XnorOyYZrzg3
GEORGIA PACIFIC CORPORATION GYPSUM DIVISION TIGARD, OREGON
May 28, 1975
TO:
Hr. H. A.'-Palinouaki - Chicago
Mrr~Gr^-F-.-~Fowler - Marietta
-Mrr_E~tT~Aasen- - Portland
Ms.-Rv -L-r--Diyen - Portland
Mr-r--J-.--Van - Portland
Mr-, it.
Petralinp - Wilmington
Mt~J. D->--Moss - Wilmington
f'|
-.Mr-^--CT~-W7~ LehnerT-- Tigard--/^.
Tigard Lab^^mJ^'t coi-*r fo'.! :C, T,
ii
Pie ise cancel-the following Chicago plant formulas by removing them-from
you formula book:
1
C-976 C-978
READY MIX JOINT" COMPOUND (HAND TOOLS) READY MIX FILLER (FILLER X)
CANCELLED CANCELLED
Attached find the following Chicago plant formula revisions:
C-970 C-971 C-972
C-,973 C-974 C-975
READY MIX FILLER READY MIX JOINT COMPOUND(HAND TOOLS) READY MIX FILLER READY MIX FILLER (FILLER X) READY MIX TOPPING COMPOUND (HAND TOOLS READY MIX TOPPING COMPOUND (MACHINE)
REVISED REVISED REVISED REVISED REVISED REVISED
Please sign and return the attached tear sheet.
TO: TIGARD GYPSUM LAB
C-976 C-978 C-970 C-971 C-972 C-973 C-974 C-975
READY MIX JOINT COMPOUND READY MIX FILLER READY MIX FILLER READY MIX JOINT COMPOUND READY MIX FILLER READY MIX FILLER READY MIX TOPPING COMPOUND READY MIX TOPPING COMPOUND
SIGNED
u
PLANT
WNG
CANCELLED CANCELLED REVISED REVISED REVISED REVISED REVISED REVISED
DATE
^/
/
SGP 0017829
GEORGIA PACIEIC CORPORATION GYPSUM DIVISION TIGARD, OREGON
April 19, 197S
TO:
Mr. M. A. Palmowski - Chicago
Me. ft Ti1- Fowl p-r - Maj2i-ejha--=.
--Mrr~&^---G-. -Corkill--Per-tiand-
-Mrr Et" r~Aa-oon-----Portland
J.~~iair~=~~Portland
-Mb. R. I'. Dixon'-"'Portland '
Jfer- C .--W
1 Tigard
Tigard
Enclosed please find the following Chicago, Illinois, Plant Formulas:
C-973 C-974 C-974 C-975 y
READY MIX FILLER READY MIX JOINT COMPOUND (HAND TOOLS) PAGE 2 READY MIX TOPPING COMPOUND (HAND TOOLS)
NEW NEW NEW NEW
Please sign and return the attached tear sheet.
TO: TIGARD GYPSUM LAB
C-973 C-974 C-974
C-975
READY MIX FILLER READY MIX JOINT COMPOUND (HAND TOOLS) PAGE 2
READY MIX TOPPING COMPOUND (HAND TOOLS)
NEW NEW NEW
NEW
signed
HCF ^
4/19/73
' plant
DATE <.^-73
SGP 0017830
Supersedes Formula Z-&3&97S
Dated:
2/22/78
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-97 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound used for finishing joint and spotting nail heads.
FORMULA Raw Material
_/Proxcel-CRL
-/Filler C-970 7?3
-/Elvace H*-2603 -/Nalco 71D-5 -/Acrysol ASE-60 /*Water
Function
Preservative Filler Adhesive Defoamer Thickener Solvent
RM Spec
185 125 147
Percent
Lbs/Batch
.048
1.0
9: w.-es?.** 1950.0
.
5.596.3* 2 7Hlfr. 0 (4-* gals . )
.096-^
2.0
.193.'^
4.0
---11-14.0 (134''Gals.
> >187.0*
*Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary + 8 gallons per batch.
7
**One batch yields^+l five gallon p4.il Ready Mix joint compound at 62 lbs/pail.
SEPCIAL MIXING INSTRUCTIONS
WORKING CONSISTENCY Specifications for Paste
Blend ingredients in following order:
1) Water
2) Elvace
3) Nalco
4) Filler C-97Q773
5) Mix until filler is thoroughly dispersed
6) Add Acrysol ASE-60
7) Mix until Ready Mix is smooth - check viscosity
and pH
,
il <
Refer to Plant Testing Procedure No. 32.
If paste
is not proper working consistency, a maximum of 5 cc
water per 150 grams of paste may be added to adjust.
Brabender: (580 ^ 20) For machine tools add 7 gallons H2O (400 + 2C)
PH
Minimum - 9.0
Maximum - 9.5
WORKING PROPERTIES Specifications
Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES
Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75%.fiber tear when delaminated.
CRACK RESISTANCE Specifications
Refer^.to Plant Testing Procedure No. 37. Rating shall be 4 of better.
COLOR Specifications
-/denotes change
White Dried compound shall match color of standard sample.
HCF:jr
SGP 0017831
CLOSED ^/3/P|
GEORGIA-PACIFIC CORPORATION
GYPSUM DIVISION TIGARD, OREGON
TO:
Mr. M. A. Palmowski - Chicago -Mr-r E. L. Aason--1- Porbtand -Mg-r-D. C. Corkill------ Portland Ms , p T--Dixon - -P-or^t-land Jte-t--Gt--W,--Lohnort----Tigard
Tigard Lab
December 17, 1979
Enclosed please find the following CHICAGO, ILLINOIS Plant Formulas:
C-970 C-971 C-972 C-973 C-974 C-975"X
Ready Mix Topping Compound (Hand Tools) Ready Mix Filler Ready Mix Joint Compound (.Hand Tools) Ready Mix Filler Ready Mix Joint Compound (Hand Tools) Ready Mix Topping Compound (Hand Tools)
NEW Revised Revised CANCEL CANCEL CANCEL
.?i5_^i2Li_S2^_turn_the_attached_tear_sheet.
TO: TIGARD GYPSUM LAB
C-970 C-971 C-972 C-973 C-974 C-975
Ready Mix ToppingCompound (Hand Tools) Ready Mix Filler Feady Mix Joint Compound(Hand Tools) Ready Mix Filler Ready Mix Joint Compound (Hand Tools) Read Mix Topping Compound (Hand Tools)
NEW Revised Revised CANCEL CANCEL CANCEL
S igned:
HCF-.ps 12/17/79
^ > P lant:
_____________ Date: /?~/7- 7f SGP 0017832
)'
April 24, 1979.
Supersedes Formula C-975 Dated: 10/5/78
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound used for finishing joint and spotting nail heads.
FORMULA Raw Material
Function
RM Spec Percent Lbs/Batch
-PMA'30 - .
Filler C-973 Elvace JCM Nalco 71D-J
***Paragum 1461 1 - c I
. *Water
Preservative Filler Adhesive Defoamer Thickener Solvent
----
--
IS 5 125
_
--
.078 95.233
4.349
.098 .244
--
O
O
--1 1
O
ON to
1.6
1950.0
2.0 5 .0
- 991.0 * (.119
gals gal;
100.000 3038 . 6**
^Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary i 8 gallons per batch).
**One batch yields 49 it 1 five gallon pail Ready Mix joint compound at
62 lbs/pail.
*** Acrysol ASE 60 can be substituted at a loading of 41bs./batch (.195%).
SPECIAL MIXING INSTRUCTIONS
- Blend ingredients in following order: 1) Water
2) Elvace JCM
3) Nalco
4) Filler C-973 5) Mix until filler is thoroughly dispersed
6) Add Parajum 146 1
7) Mix until Ready Mix is smooth - check
viscosity and pH
WORKING CONSISTENCY Specifications for Paste
Refer to Plant Testing Procedure No. 32. If paste is not proper working consistency, a maximum of 5 cc water per 150 grams of paste may be added to adjust.
Brabender: (5&0 20) For machine tools add 7 gallons H2O (400 20)
pH
Minimum - 9.0
Maximum -9.5
WORKING PROPERTIES Specifications
BONDING PROPERTIES Specifications
- Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
- Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75/ fiber tear when delaminated.
CRACK- RESUSTA.NCE Specification
- Refer to Plant Testing Procedure No. 37. Rating shall be 4 or better.
COLOR Specifications
HCF:ps -
- White Dried compound shall match color o.f standard sampl
SGP 0017833
\ Closed
ZLo S eo
GEORGIA-PACIFIC CORPORATION GYPSUM DIVISION TIGARD, OREGON
S--A4-79
April 24, 1979
TO:
-tin--H-r-
Pa 1 mfvejeld_j*--Chicago
Mr
_L_
-Portland
Mr-m-0T-6-r Corkill
- -Hr I G F.
- MariP- tta
MrGt-W. LehueU. - Tigard
TigdLd Lab
Enclosed please find the following Chicago, Illinois, Plant Formula Revisions:
C-974
Ready Mix Joint Compound (Hand Tools)
Revised
C-975
Ready Mix Joint Compound (Hand Tools)
Revised^
Please sign and return the attached tear sheet.
TO: Tigard Gypsum Lab
C-974 C-975
Ready Mix Joint Compound Ready Mix Joint Compound
Signed
HCF 4/24/79
_Plant
Revised Revised
Date
SGP 0017834
October 5, 1978 Supersedes Formula C-975 Dated: 4/20/78
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound used for finishing joint and spotting nail heads.
FORMULA Raw Material
Function
RM Spec Percent Lbs/Batch
_/ -PMA 30
-/ Filler C-973
Preservative Filler
/ Elvace JCM
Adhesive
./ Nalco 71D-5
Defoamer
>* *4 _/ A-ei^sudrAOE 60HC* Thickener
-/ *Water
Solvent
is 5
125
w?-
.078
1.6
95.280^351950.0
4.340? 89.0 (10.0 gals.)
.098
^2.0
rl&SWV
0
-- - 991.0* ( 119 gals.)
100.000 303fc 6**
^Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary 1 8 gallons per batch).
/ **one batch yields 62 lbs/pail.
y /9czy s
SPECIAL MIXING INSTRUCTIONS
49 i 1 five gallon pail Ready Mix joint compound at
-
- Blend ingredients in following order: 1) Water 2) Elvace JCM 3) Nalco 4) Filler C-973 5) Mix until filler is thoroughly dispersed 6) Add 7) Mix until Ready Mix is smooth - check viscosity and pH
WORKING CONSISTENCY Specifications for Paste
Refer to Plant Testing Procedure No. 32. If paste is not proper working consistency, a maximum of 5 cc water per 150 grams of paste may be added to adjust.
Brabender: (560 20) For machine tools add 7 gallons H2O (400 20)
pH
Minimum - 9.0
Maximum -9.5
WORKING PROPERTIES Specifications
Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications
Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75$ fiber tear when delaminated.
CRACK RESUSTANCE Specification
Refer to Plant Testing Procedure No. 37. Rating shall be 4 or better.
COLOR Specifications
GWG:jr
- White Dried compound shall match color of standard sample
SGP 0017835
April 24, 1979 Supersedes Formula C-974 Dated: 10/5/78
CHICAGO, ILLINOIS PUNT FORMUM READY MIX JOINT COMPOUND C-974 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix- Joint Compound used for taping, topping and texturing.
FORMUU Raw Material
Function
RM Spec Percent Lbs/Batch
PMA 30
Filler C-973 Elvace JCM
Nalco 71D-5
***Paragum 146
*Water
Preservative --
Filler
--
Adhesive
1$5
Defoamer
125
Thickener
Solvent
--
.077 94.040
5.546
.096 . 241
--
1.6 1950.0
115.0
2.0 5 .0
(13.0 gals.) 965.0 (-116gals
100.000 3038.6 **
^Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary 8 gallons per batch).
**0ne batch yields 49- 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
*** Acrysol ASE 60 can be substituted at a loading of 4 lbs/batch (.193%).
SPEICAL MIXING INSTRUCTIONS
- Blend ingredients in following order: 1) Water
2) Elvace JCM
3) Nalco
4) Filler C-973
5) Mix until filler is dispersed
6) Add'Paragum 146
-/ 7) Mix until Ready Mix is smooth - pumping
viscosity should b3 580 20
WORKING CONSISTENCY Specifications for
Paste
- Refer to Plant Testing Procedure No. 32. If paste is not proper working consistency, a maximum of 5 cc water per 150 grams of paste may be added to adjust.
Brabender: (5&0 20) For machine tools add 7 gallons H2) (400 1 20)
pH
Minimum - 9.0
Maximum -9.5
WORKING PROPERTIES Specifications
- Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
HCF:ps
Continued on Page 2....
SGP 0017836
April 20,' 1973 Formula C-975 NEW
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound used for finishing joint and spotting nail heads.
FORMULA Raw Material
Function
RM Spec Percent Lbs/Batch
Proxcel ' CRL
Filler C-973 Elvace JCM
Nalco 71D-5 Acrysol A.SE-60 *Water
Preservative Filler Adhesive Defoamer Thickener
Solvent
--
--
135 125 147 --
.043 95.303
4.350 .093 .196 --
1.0 1950.0
89.0 (10.0 gals.) 2.0 4.0
1130.0 (135.6 gals.)
100.000 3176.0**
^Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary 1 8 gallons per batch).
**One batch yields 51 i 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
SPECIAL MIXING INSTRUCTIONS
- Blend ingredients in following order: 1) Water 2) Elvace JCM 3) Nalco 4) Filler C-973 5; Mix until filler is thoroughly dispersed 6) Add Acrysol ASE-60 7) Mix until Ready Mix is smooth - check viscosity and pH
WORKING CONSISTENCY Specifications for Paste
Refer to Plant Testing Procedure No. 32. If paste is not proper working consistency, a maximum of 5 cc water per 150 grams of paste may be added to adjust.
Brabender: (530 20) For machine tools add 7 gallons H2O (400 20)
pH
Minimum - 9.0
Maximum -9-5
WORKING PROPERTIES Specifications
BONDING PROPERTIES Specifications
- Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
- Refer to Plant Testing Procedure No. 35* After compound has dried, tape shall show at least 75$ fiber tear when delaminated.
CRACK RESUSTANCE Specification
- Refer to Plant Testing Procedure No. 37. Rating shall be 4 or better.
COLOR Specifications
HCF:jg
- White Dried compound shall match color of standard sample
SGP 0017837
October 5, 1978 Supersedes Formula C-975 Dated: 4/20/78
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound used for finishing joint and spotting nail heads.
FORMULA Raw Material
Function
RM Spec Percent Lbs/Batch
/ jma 30
/ Filler C-973 Elvace JCM
/ Nalco 71D-5 / Acrysol ASE-60 / *Water
Preservative Filler Adhesive Defoamer Thickener Solvent
--
--
IS 5 125 147 --
.078 95.280 4.349
.098
.195 --
1.6 1950.0
89.0 (10.0 gals.) 2.0 4.0
: 991.0*- ( 119 gals.)
100.000 3037 . 6**
*Approximate_y 56.5 lbs/100 lbs. of active ingredients (tais may vary 1 8 gallons per batch).
/ **0ne batch yields 49 - 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
SPECIAL MIXING INSTRUCTIONS
- Blend ingredients in following order: 1) Water 2) Elvace JCM 3) Nalco A) Filler C-973 5) Mix until filler is thoroughly dispersed 6) Add Acrysol ASE-60 7) Mix until Ready Mix is smooth - check viscosity and pH
WORKING CONSISTENCY Specificat'.ons for Paste
Refer to Plant Testing Procedure No. 32. If paste is not proper working consistency, a maximum ol 5 cc water per 150 grams of paste may be added to adjust.
Brabender: (580 20) For machine tools add 7 gallons HpO (400 20)
pH
Minimum - 9.0
Maximum -9-5
WORKING PROPERTIES Specifications
- Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications
- Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75$ fiber tear when delaminated.
CRACK RESUSTANCE Specification
COLOR Specifications
GWG:ir
- Refer to Plant Testing Procedure No. 37. Rating
shall be 4 or better.
SGP 0017838
- White
Dried compound shall match color o.f standard sample
April 24, 1979 Supersedes Formula C-975 Dated: 10/5/78
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (HAND TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound used for finishing joint and spotting nail heads.
FORMULA Raw Material
Function
RM^ Spec Percent Lbs/Batch
J?MA 30
Filler C-973 Elvace JCM
Nalco 71D-.5
***Paragum 146
. *Water
Preservative Filler Adhesive Defoamer Thickener Solvent
--
IS 5 125
--
.078 95.233
4.349 .098 .244 --
1.6 1950.0
89.0 (10.0 gals.)
2.0 5 .0
- 991.0* ( 119 sals.)
100.000 3038 . 6**
^Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary 1 8 gallons per batch).
**0ne batch yields 49 1 1 five gallon pail Ready Mix joint compound at
62 lbs/pail.
*** Acrysol ASE 60 can be substituted at a loading of 41bs./batch (.195%).
SPECIAL MIXING INSTRUCTIONS
- Blend ingredients in following order:' 1) Water 2) Elvace JCM
3) Nalco
4) Filler C-973 5) Mix until filler is thoroughly dispersed 6) Add Paragum 146
7) Mix until Ready Mix is smooth - check viscosity and pH
WORKING CONSISTENCY Specifications for
Paste
Refer to Plant Testing Procedure No. 32. If paste is not proper working consistency, a maximum of 5 cc water per 150 grams of paste may be added to adjust.
Brabender: (580 20) For machine tools add 7 gallons H2O (400 20)
PH
WORKING PROPERTIES Specifications
Minimum - 9.0
Maximum - 9.5
Refer to Plant Testing Procedure No. 33. Compound shall be plastic, buttery working and free of any coarse, gritty or undispersed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications
Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75$ fiber tear when delaminated.
CRACK RESUSTANCE Specification
Refer to Plant Testing Procedure No. 37. Rating shall be 4 or better.
COLOR Specifications
HCF:ps
- White Dried compound shall match color of standard sample
SGP 0017839
December 8, 1967 NEW FORMULA
CHICAGO. ILLINOIS PLANT FORMULA READY MIX JOINT COMPOUND C-975 (HAND TOOLS ) (READY MIX "X")
DESCRIPTION OF PRODUCT
- White Ready Mixed Joint Compound used for taping, covering tape, filling cornerbead and spotting nails.
FORMULA
Raw Material
V,Tater
. "
Nalco 71-D5 Troysan PMA 30 Filler C-970 Elvacet 81-iCC Benzoflex 50
Source Chicago Plant
7,, Act. Ingr.
.
Nalco Chemical Co. Troy Chemical Co. Chicago Plant DuPont Tennessee Products Chem.
0.10 0.05 91.35 8.00 G. 50 100.00
Lbs./Batch
400.0 (48 gal.)'
0.8 0.4 700.0 61.5 4.0 1166.7**
'^Approximately 52 lb./lOO lbs. of active ingredients (this may varjri.+ 2
gallons per batch).
v
**One batch yields 17 (-f) - 5 gallon pails of Ready Mix Joint Compound at 65.6 lbs./pail.
TESTING PROCEDURE
WORKING CONSISTENCY - Refer to Plant Testing Procedure No. 32. Specifications for Paste: If paste is not proper working consistency, maximum of 55 c.c. water per 150 grams of paste may be added to adjust.
a
Brabender
440 + 30
WORKING' PROPERTIES - Refer to Plant Testing Procedure . Compound shall, be plastic, buttery working, and free of or undispersed particles, Plaster shall be free from 1 piete mixing.
33. ,ny coarse, gritty, .ps due to incom-
BONDING PROPERTIES Specifications:
Refer to Plant Testing Procedure No. 35. After compound has dried, tape snail show at least 757o fiber tear when delaminated.
CRACK RESISTANCE Specifications:
Refer to Plant Testing Procedure No. 37. There shall be no large fissure cracks in the wsdge, and noi cracks in the thinner half of the wedge.
COLOR Specifications:
White Dried compound shall match color of standard sample.
?J SGP 0017840
March 6, 1974 New Formula C-975
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (MACHINE TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound for taping, topping, and spotting nailheads.
FORMULA
Raw Material
Function
Percent
Water
Solvent
Nalco
Anti-foaming
Polyvinyl Acetate Emulsion
(preplasticized)
Adhesive
Filler C-973
-
Filler
agent
0.1
5.4 94.5
100.0
Lbs/Batch
10S0.00(135 gals)* 2.00
114.00(12.5 gals) 1992.00
3188.00**
*Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary - 8 gallons per batch).
**0ne batch yields 97-1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
WORKING CONSISTENCY
- Refer to Plant Testing Procedure No 1/^2. "
Specifications for Paste Brabender: 400 - 20
If paste is not proper working consistency,
a maximum of 5 cc water per 150 grams of paste may be added to ajdust.
WORKING PROPERTIES Specifications:
Refer to Plant Testing Procedure No. 33 Compound shall be plastic, buttery working, and free of any coarse, gritty, or undis persed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications:
Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show
at least 75$ fiber tear when delaminated.
CRACK RESISTANCE Specifications:
Refer to Plant Testing Procedure No. 37. There shall be no large fissure cracks in
the wedge, and no cracks in the thinner half of the wedge.
COLOR ~ Specifications:
White Dried compound shall match color of standard sample.
WNG:jg
SGP 0017841
March 25, 1974 Supersedes Formula C-9? Dated 3/6/74
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (MACHINE TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound for taping, - topping, and spotting nailheads.
FORMULA
Raw Material
Function
Percent
Water
Solvent
Nalco
Anti-foaming
Polyvinyl Acetate Emulsion
(preplasticized)
Adhesive
Filler C-973
-"
Filler
agent
0.1
5.4 94.5 '
100.0
Lbs/Batch 1045.00(131 gals)*
2.00
112,00(12.4 gals) 1950.00 3112.00**
Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary - 8 gallons per batch).
**0ne batch yields 50 t 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
WORKING CONSISTENCY
- Refer to Plant Testing Procedure No^^2.
Specifications for Paste Brabender: 400 - 20
If paste is not proper working consistency,
a maximum of 5 cc water per 150 grams of paste may be added to ajdust.
WORKING PROPERTIES Specifications:
- Refer to Plant Testing Procedure No. 33 Compound shall be plastic, buttery working, and free of any coarse, gritty, or undis persed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications:
- Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75# fiber tear when delaminated.
CRACK RESISTANCE Specifications:
- Ref.er to Plant Testing Procedure No. 37. There shall be no large fissure cracks in
the wedge, and no cracks in the thinner half of the wedge.
COLOR Specifications:
- White
Dried compound shall match color of standard sample.
WNG: j g
SGP 0017842
/ ' .i'i : i ,
-l -
Mareh 25, 1974
Supersedes Formula
Dated .1
:
C-97
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (MACHINE TOOLS)
DESCRIPTION OF PRODUCT '
- White Ready Mix Topping Compound for taping, topping, and spotting nailheads.
FORMULA
Raw Material
Function ft. M
Percent
Water
Solvent
'-------
--
Nalco
t Anti-foaming agent i?v 0.1
Polyvinyl- Acetate-Emulsion
X'V
(preplasticized)
Adhesive
\ \ it
-*-4-
Filler C-973
Filler
~ 1/994^5-
100.0
Lbs/Batch
1045.00(131 gals )* 2.00
/<//- CTD 112 , QQ(15v4"- gal3) 1950.00
3112.00**
*Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary - 8 gallons per batch).
**0ne batch yields 50 i 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
WORKING CONSISTENCY
- Refer to Plant Testing Procedure No.-32.
Specifications for Paste If paste is not proper working consistency,
a maximum of 5 cc water per 150 grams of
paste may be added to ajdust.
Brabender: 400 - 20
WORKING PROPERTIES Specifications:
- Refer to Plant Testing Procedure No. 33 Compound shall be plastic, buttery working, and free of any coarse, gritty, or undis persed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications:
- Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show at least 75$ fiber tear when delaminated.
CRACK RESISTANCE Specifications:
- Refer to Plant Testing Procedure No. 37. There shall be no large fissure cracks in
the wedge, and no cracks in the thinner half of the wedge.
COLOR Specifications:
- White
Dried compound shall match color of standard sample.
WNG: j g
SGP 0017843
Kay 27, 1975 Supersedes Formula C-975 Dated 3/25/74
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (MACHINE TOOLS)
DESCRIPTION OF PRODUCT - White Ready Mix Topping Compound for taping, topping, and spotting nailheads.
FORMULA --------Raw Material
Water Nalco
Elvace 1875 Filler C-973
Function
RM Spec Percent
Solvent Anti-foaming
Agent Adhesive Filler
'--
125 185
--
--
0.1 2.0 97.9
100.0
Lbs/Batch
1048.00(131 gals)*
2.00 41.00 (4.6 gals) 2021.00 3112.00**
*Approximately 56.5 lbs/100 lbs. of active ingredients (this may vary 1 8 gallons per batch).
**0ne batch yields 50 - 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
WORKING CONSISTENCY
- Refer to Plant Testing Procedure No.^2.
Specifications for Paste If paste is not proper working consfitlsncy,
'* a maximum of 5 cc water per 150 grams of
paste may be added to ajdust.
Brabender: 1+00 - 20
WORKING PROPERTIES Specifications:
Refer to Plant Testing Procedure No. 33 Compound shall be plastic, buttery working, and free of any coarse, gritty, or undis-. persed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Specifications:
Refer to Plant Tes*ing Procedure No. 35. After compound has dried, tape shall show at least 75# fiber tear when delaminated.
CRACK RESISTANCE Specifications:
Refer to Plant Testing Procedure No. 37. There shall be no large fissure cracks in the wedge, and no cracks in the thinner half of the wedge.
COLOR Specifications:
White Dried compound shall match color of standard sample,
WNG:elz -/ denotes change
SGP 0017844
May 27, 1975 Supersedes Formula C-97 Dated 3/25/74
CHICAGO, ILLINOIS, PLANT FORMULA READY MIX TOPPING COMPOUND C-975 (MACHINE TOOLS)
DESCRIPTION OF PRODUCT
- White Ready Mix Topping Compound for taping, topping, and spotting nailheads.
y FORMULA Raw Material
Water Nalco
Elvace 1875 Filler C-973
Function
RM Spec
Solvent Anti-foaming
Agent Adhesive Filler
--
125 185
--
Percent
--
0.1 2.0 97.9 100.0
Lbs/Batch
1043.00(131 gals)*
2.00 41.00 (4.6 gals) 2021.00 3112.00**
*Appr iximately 56.5 lbs/100 lbs. of active ingredients (this may vary - 8 gallons per batch).
**0ne batch yields 50. - 1 five gallon pail Ready Mix joint compound at 62 lbs/pail.
WORKING CONSISTENCY
- Refer to Plant Testing Procedure No. 32.
Specifications for Paste If paste is not proper working consistency,
a maximum of 5 cc water per 150 grams of
paste may be added to ajdust.
Brabender: 400 - 20
WORKING PROPERTIES Specifications:
Refer to Plant Testing Procedure No. 33 Compound shall be plastic, buttery working, and free of any coarse, gritty, or undis persed particles. Material shall be free from lumps due to incomplete mixing.
BONDING PROPERTIES Speci; 'ications:
Refer to Plant Testing Procedure No. 35. After compound has dried, tape shall show
at least 75$ fiber tear when delaminated.
CRACK RESISTANCE Specifications:
COLOR Specifications:
Refer to Plant Testing Procedure No. 37. There shall be no large fissure cracks in the wedge, and no cracks in the thinner half of the wedge.
White Dried compound shall match color of standard sample.
WNG:elz -/ denotes change
**> SGP 0017845
>Cfi
03
H 2n
8|SOt/j
* n
2o
h
*0
o*
=s'Jott
(71
d
n
H
C/3
SGP 0017828
SGP 0017846
MILFORD FORMULA # 975
XXHE8XBSXXXXHXB
ASBESTOS CONTAINING PRODUCTS
*
1
SGP 0017847