Document zdVzgXQ5q9B8wYdNa00KJzJ1m

-48302 _ KULES AND REGULATIONS has received prior, approval by the disposal site where asbestos-containing ttd waste material has been deposited, except shall bo used M l**ee ' (1) Tbi vutt material shall be covered with at least 15 centimeters (ca. 6 laches) of com pacted non-ssbestos-containtng mate rial, sad a cover of vegetation shall be as provided in paragraph (e) of this section. ' (b) Waning signs *n be displayed at all entrances, and along the property line of the site or along the perimeter of Particular dust by thedu^S^L*^ agent manufacturer, oth^r t?*i!**4 feettve dust suppression ** used upon prior approval ^ by th! 2?* * lstrator. For purposes of grown and maintained on the area ade the sections ofrthe rite where asbestos- waste crankcase oil is not cS22*- quate to prevent exposure of the asbes containing waste material is dust suppression agent. ^* tos-containing waste material; or at intervals of 100 m (ca. 330 ft) or less (U) The asbestos-containing waste except as specified in paragraph (d) of material shall be covered with at least 80 this section. Signs shall be posted in such Subpart E--National Emission SUndM- for Mercury *`"l centimeters (ca. 3 feet) of compacted a manner and location that a person may 10. Section 61.50 isrevised to nn ^ non-asbestos-containing material and easily read the legend. The warning follows: re4~ * maintained to prevent exposure of the signs required by thi paragraph hn asbestos-containing waste; or conform to the requirements of 20" x 14" g 61.50 Applicability. (ill) For inactive waste disposal sites upright format signs specified In 29 CFR The provisions of this subpart s^v - -for asbestos a resinous or petro 1910.145(d) (4) and this paragraph. The pllcable to those stationary sources'*^ leum-based dust suppression agent which signs shall display the following legend process mercury ore to recover mereST effectively binds dust and controls wind in the lower panel, with letter sizes and use mercury chlor-alkall cells to ptocu erosion shall be applied. Such agent shall styles of a visibility at least equal to chlorine gas and alkali metal hjdroxwt be used as recommended for the partic those specified in this paragraph. ular asbestos tailings by the dust sup and Incinerate or dry wastewater irtau ment plant sludge. pression agent manufacturer. Other equally effective dust suppression agents may be used upon prior approval by the Anzrros W**ra Disposal 8m ' - Do Not Croats Ojist 11. Section 61.51 is amended by addtac paragraphs (1) and (m) as follows: Administrator. For purposes of-this para ,graph, waste crankcase oil is not con ' Breathing Asboataa u Hazardous to ToorStalth 61-51 Definitions. - sidered a dust suppression agent. 7. The first sentence in S 61.23 Is re vised as follows: - g 61.23 Air-Cloning. ' If air-clesnlng is elected, as permitted by 15 61.22(f) and 81.22(d) (4) (iv), the requirements of this section must be met. 8. The first sentence in | 61.24 Is re vised and redesignated as paragraph (e) and new paragraphs (c> and (d) are added as follows; ' 61.24 Reporting. -' Notation ` . (1) "Sludge" means sludge produced by a treatment plant that processes munici 1" Sans Sarlf, Oolitic or Slodt pal or industrial waste waters. *. %" Sans Serif, Oethle or Block - (m) "Sludge dryer" means a* device . 14 Point Oothle . used to reduce the moisture content of sludge by heating to temperatures above Spacing between lines shall be at least 63*C (ca. 150*F) directly with combus equal to the height of the upper of the tion gases. two lines. - (c) The perimeter of the disposal site shall be fenced in order to adequately 12. Section 61.52 is revised to read as follows: deter access to the general public except g 61.52 ' Emiukm lUndard. as specified in paragraph, (d) section. of this (a) Emissions to the atmosphere front mercury ore processing facilities ai:d (d) Warning signs and fencing are mercury cell chlor-alkall plants shall not not required where the requirements of exceed 23QQ grams of mercury per 24- (c)For sources subject to 55 61.22(J) paragraph (e)(1) of this section are hour period. and 61.22<lc) t . met, or where a natural barrier ade (b) Emissions to the atmosphere from (1) A brief description of each process quately deters access to the general sludge Incineration plants, sludge drying that generates asbestos-containing waste public. Upon request and supply of ap plants, or a combination of these that material. propriate information,- the Administra process wastewater treatment plant (2) The average weight of asbestos- tor will determine whether, a fence or a sludges shall not exceed 3200 grams of containing waste material disposed of. natural barrier adequately deters access mercury per 24-hour period. measured in kg/day. - (3) The emission control methods used in all stages of waste disposal. to the general public, y-"'- . (e) Bather than meet the require ment of paragraph (a) of this section, an 13. Section 6U3 is amended by adding paragraph (d) aa follows: . (4) The type of disposal site or incin owner or operator may elect to meet 861.53 Stack sampling.' eration site used for ultimate disposal, the requirements of paragraph (e> (1) or s the name of the site operator, and the' name and loeatlonof the disposal site. (d) For sources subject to 161.22(1): - (l) A brief description of the site. (e> (2) of this section.-or may use an al ternative control' method -for emissions from active waste disposal -sites which has received prior approval by the (d> Sludge Incineration and drying plants. . (1) Unless a waiver of emission testing is obtained under 161.13, each owner or (2) The method or methods used to Administrator. ' operator of a source subject to the stand comply with thh standard, or alternative (1) At the end of eeeh'operating day, ard in 161.52(b) shall test emissions from procedures to be used. ~ ' or at least once every 34-hour period that sourct. Such tests shall be conducted (e) Such information shall accom while the site is in continuous operation, in accordance with the procedures set pany the information required by f 81.10. the asbestos-containing waste material forth either in paragraph (d) of this The information described in this section which was deposited at the site during section or in f 61.54. shall be reported using the format of the operating day or previous 24-hour (2) Method 101 in Appendix B to this Appendix A of this parti period shall be covered with at least 15 pert shall be used to test emissions as 9. A new section 81.25 is added to sub part B as follows: '61.25 Waste disposal sites. centimeters (ca. 6 inches) of ennpacted follows: non-asbestos-containtnraiatenal. . (I) The test shall be performed within (2) At the end of each operating day, 90 days of the effective date of these or at least once every.'34-hour period regulations in the case of an existing . In order to be an acceptable site for while the disposal site -is in continuous source or a new source which has an disposal of asbestos-containing waste operation, the ssbcstos-contain'ng waster initial startup date preceding the effec material under 16132 (J) ssd (k), an material which was deposited at the site tive date. - active waste disposal site shall meet the during the operating day or prerlous 24- (II) The test shall be performed within requirements of this section. hour period shall be corned with a res 90 days of startup in the case of a new (a) There shall be no visible emissions inous or petroleum-based dust suppres source which did not have an initial to the outside air from any active waste sion agent which effectively binds dust startup date preceding the effective date. HDKAl tmsna, VOL 40, NO. t00 4Wa>r, OCTOUI 14, 197S 0006125 KULfS AND UGULATIONS 48301* (b), (J>.or flc) of this erUnn, rvrhf&Q- vin he labeled with a warning label temperature at the weete *11* i_ ure shall not be a-violation of such emiasion requirements. . . . - less than --9*C (ca. 15*F). The ambient air temperature shall be determined by (h> Fabricating: `Thar* shall be no ConWin* Asbrnto* an appropriate measurement visible emiatiotu.to theoutside air, . Avoid opening or Breaking Container with sn-eccuracy of ml*C <m2*F> and cept as provided,in paragraph (i> ol this - Breathui* Asbestos is Hasardous recorded at least at hourly intervals dur section, from any ol the following op* :o Tour Heeitn ing the period that the operation of the ' erations if they uw commercial iitxitQS or from any building or structure in which such, operations are conduct*! (l) The fabrication of cement building products.- ' ' <2) The fabricstion of friction prod* ucts, except- those operations that pri marily install asbestos friction materials on motor vehicles! ' . (3) The fabrication of cement or sili cate board for ventilation hoods; ovens; electrical panels; laboratory furniture; bulkheads. - partitions and'ceilings for marine construction; and flow control devices for-the-molten metal industry. (1) Insulating: Molded Insulating ma terials which are friable andwet-applied Initiating materials- which are friable. after drying, installed after the effective date of thee* regulatlonsrshall contain no commercial asbestos. The provisions Alternatively, warning labels specified' wetting system is suspended. Records of by Occupational- Safety end Health such temperature measurements be Standards of ths Department of Labor, retained at the source for a mtntrw,,-- 0f Occupational Safety and Health Admin two years and made available for inspec istration (OSJA) under 29 CFR 1910.- tion by the Administrator. - . 93a(g> (2) (ii> may be used. - (1) The owner of any inactive waste 01) processing of asbeetoe-containing disposal site, which was operated by", waste material into non-frlable forms: sources covered under 161.23 (a). <c> or (A) All asbestos-containing waste . (h) and where asbestos-containing waste material shall be formed Into non-frlable material produced by such sources waa pellets or other shapes and deposited et deposited, shall meet the following waste disposal sites which are operated standards: .. in accordance with the provisions of . (1) There shall be no visible emissions i 61.25. ' * to the outside air from an inactive waste (B) There shall be no visible emis - disposal site subject to this paragraph, sions to the outside air from the collec . except as provided In paragraph (1) (5) tion and processing of asbestos-' of this section. ,, - .. containing waste material, except as (2) Warning signs shall bo displayed specified in paragraph (f) of this section. at all entrances, and along.tho property. (4) For the purposes of -this para line of the site or along the perimeter of graph (J). the term.all-asbestos-con- ' the sections of the site where asbestos- of this paragraph do- not apply to insu lating materialawhichare spray applied; such materials.: are :regulated under S 61.22(e).V-T-- - V- -T.--.' (j) Waste disposal for manufacturing, fabricating, demolition, renovation and spraying operations: The owner or op erator of any source covered under the provisions of paragrapha (c), (d), (e), or (h) of this section shall meet the fol taining. waste material aal applied to demolition and renovation operations covered by paragraph (d> of this sec tion Includes only friable asbestos wests and control device asbestos waste. (k) Waste disposal for asbestos mills: The owner or operator of any source covered under the provisions of para graph (a) of this section shall meet the following standard: ' containing waste material waa deposited, at intervals of 100 m (ca. 330 ft) oa lass, except as specified in paragraph (1) (4) of this section. Signs (hall be potted in ' such a manner and location that a person may easily read the legend. The warning signs required by this paragraph H*11 conform to the requirements of 20" x 14" upright format signs specified In 29 CFR 1910.145(d) (4) and this paragraph. The lowing standards: (1> There shall be no visible emissions to the outside air, except as provided in (l) There shall be no visible emis sions to the outside air, except as pro vided in paragraph (k) (3) of this section, signs shall display the following legend in the lower panel, with letter sizes and styles of a visibility at least equal to those paragraph <j) (3) of this section, dur during the collection, processing, pack specified in this paragraph. ing the collection; processing. Including aging, transporting or deposition of Incineration; packaging; transporting; any asbestos-containing waste mate LSOSMB . or deposition of any asbestos-containing rial which is generated by such source. Amerce Wean Dxsmml Srre waste material which is generated by (2) All asbestos-containing waste ma . So Bet Create Duet... . such source. (2) All asbestos-containing waste ma terial shall be deposited et wests dis posal sites which are operated-in accord terial shall be deposited at waste disposal sites which are operated in ac cordance with the- provisions of 4 81.25. (3) Bather than meet the requirement Breathing Asbeatoa la Hasaidooa to Tour Beaith . . Notation .. ' - ~. ance with the provisions of 181.25. of paragraph <k) (1) of this section, an 1" Sans Serif, Oothle or Bleek (3) Bather than meet the requirement owner- or operator may elect to meet of paragraph <J) (1> of this section, sa the following requirements in para >4" Sane Serif, Gothic or Sock owner or operator may elect to use graphs (k>(3> U) and <ii>, or use an 14 Point Ootids - . either of the disposal methods specified under (J) (3) (l>-and (il) of this section, or an alternative disposal method which alternative disposal mathod which has received prior approval by the Admin istrator: ' Spacing between lines shall he at least- equal to the height of the upper of the . two lines, .- has received prior approval by- the Ad ministrator: - . . (1) Treatment- of asbestoe-contalnlng waste material with water: (A) Control device asbestos waste shall be thoroughly mixed with water into a slurry and other asbestos oontetntng waste material shall be -adequately wetted. There shall be no risible emis sions to the outside air from the collec tion, mixing and wetting operations, ex cept as provided in paragraph (f> of this section. . - (B) After wetting, all asbestos-con taining waste material shall be sealed into leak-tight containers while wet, end such containers shsll.he deposited at waste disposal sites which are operated in accordance with the provisions of 181.25. . . . -, (C) The containers specified under . (i) There shall be.no risible emissions to tbs outside sir from ths transfer of control device asbestos-.waste to the' tailings conveyor, except ss provided in paragraph <f) of this section. Such waste shall be subsequently processed either as specified in paragraph (k) (3) (11) of this section or as specified in paragraph (j) (3) of this section. -. (ID All asbestos-containing waste material shall be adequately mixed, with a wetting agent recommended by the manufacturer of the agent to effectively wet dust and tailings, prior to deposition at a waste disposal site. Such agent shall he used sa recommended for the partic ular dust by agent. There ths manufacturer of the shall be no discharge of - visible emissions to the outside air from the wetting operation except as specified In paragraph (f> of this section. Wetting (3) The perimeter of the site shall he fenced in a manner adequate to deter access by the general public, except as specified in paragraph (1) (4) of thla section. ~- (4) Warning signs and fencing are not required where the requirements of paragraphs (1) (5) (i) or til) of this sec tion are met, or where a natural barrier adequately , deters access by the general public.' Upon request and supply of ap propriate information, the Adminis trator will determine whether a fence or a natural barrier adequately detera ac cess to the general public. . -- (5) Bather than meet the requirement of paragraph (1) (1) of this section, sa owner may elect to meet the require ments of this paragraph or may use aa alternative control method for emlstions ~ paragraph (J) (3) (1) (B) of this section -may be suspended- when the ambient from inactive waste disposal sites which n | 9 fi uV ' HOBAL UOKTU, VOC 40, NO. 1 tv--TUIWAT, OCTOSM 14, 1*73 . '1 (T00T512 6 48300 RULES AND REGULATIONS httan. or as tariy as possible prior to MHwnn>^wt at emergency demolition wrecking or riimwtnng of' any other portion of such building, structure, members shall, to the ousted ' possible, be removed asiSu? **^a subject to paragraph <d) (6) of this see* facility, or installation that would pre tions prior to wrecking * . Uoe. end as early a* possible prior to clude access to such materials tor sub the requirements of - commencement of renovation. Such no* sequent removal. Removal of friable (iv> or (d) (4) (v) ^1** tiee shall include the following informs* asbestos materials used for insulation freezing temperatures. ,~**"<* % tioa: (i> Name of owner or operator. or fireproofing of any pipe, duct, or -structural member which are encased in (vii) For renovation operuuoa. . exhaust ventilation.end <li) Address of owner or operator. (ill) Description of the building, struc concrete or other similar structural ma terial is not required prior to demoli teza3lE57. be used- of we-s-a!*!: specified in paragraph id (4(a, ture. facility,-or installation to be de tion, but such material shall be ade vent emissions of particulate ii?' molished or renovated, including the quately wetted whenever exposed dur material to outside air when casSTT size, age. and prior use of the structure, ing demolition. equipment resulting from thTeIi and the approximate amount of friable (il) Friable asbestos materials used would be unavoidable. Upon rcc--Tl_ asbestos material used for insulation and to insulate or fireproof pipes, ducts, supply of adequate information! tbi 7? fireproofing. boilers, tanks, reactors, turbines, fur ministrator will determine whether ' (iv) Address or location of the build naces, or structural members shall be age to equipment resulting Iram ing. structure, facility, or installation. adequately wetted during stripping, ex to comply with the provisions of Uu* (v) Scheduled starting and comple cept as provided in paragraphs (d) (4) agraph would be unavoidable. Such Le tion dates of demolition or renovation. (lv), (d)(4) (vi) or <d)(4)(vii) of-this exhaust ventilation systems ^- (vi) Nature of planned demolition or section. - - signed and operated to capture the -->-1- renovation and method(s) to be em (ill) Pipes, ducts, boilers, tanks, re tos particulate matter produced by tr ployed. ' actors, turbines, furnaces, or structural stripping and removal of friable >v--- -Crti) Procedures to be employed to members that are insulated or fire material. There shall be no visible -- meet the requirements of this paragraph proofed with friable asbestos materials sions to the outside air from such iac and paragraph (J) of this section. may be taken out of any building, struc exhaust ventilation and collection ty (vUi) The name address or loca ture, facility, or installation subject to terns, except as provided in paxaira- tion of the waste disposal site where the this paragraph as units or in sections (1) of this section. ' friable asbestos waste will be deposited. provided the friable asbestos materials (5) Sources subject to this paragm; Ox) Name, title, and authority of the exposed during cutting or.disjointing are are exempt from the requirements State or local governmental representa adequately wetted during the' cutting Si 61.05(a), 61,07. and 61.09. tive who has ordered a demolition which or disjointing -operation. Such units (6) The demolition of a building, stn. is subject to paragraph (d)(6) of this shall not be dropped or thrown to the ture, facility, or Installation, pursuant section. ' ground, but shall be -carefully lowered an order of an authorized represents (3) (D For purposes of determining to ground level. " of a State or local governmental agen whether a planned renovating operation (lv) The stripping of friable asbestos Issued because that building is strum constitutes a renovation. within the materials used to insulate or fireproof ally unsound and In danger of lmmir. meaning of this paragraph, the amount any pipe, duct, boiler, tank, reactor, tur collapse is exempt from ail but the ! of friable asbestos material to be re bine, furnace, or structural member that lowing requirements of paragraph <d> moved or stripped shall be: has been removed as a unit or in sections this section: (A) For planned renovating opera-' as provided in paragraph (d) (4) (ill) of (1) The notification requirements;; tloas involving individually non-sched this section shall be performed in ac ifled by paragraph (d) (3) of this secu ified operations, the additive amount of cordance with paragraph (d) (4) (li) of (il) The requirements on strippini friable asbestos material that can be pre this section. Rather than comply with friable asbestos materials from previo dicted will be removed or stripped at a the wetting requirement, a local exhaust removed units or sections as specific source over the maximum period of time ventilation and collection system may paragraph (d) (4) (iv) of this sectiot for which a prediction can be made. The be used to prevent emissions to the out (hi) The wetting, as specified by p- period Shan be not less than 30 days and side air. Such local exhaust ventilation graph (d) (4) (v) of this section, of not longerthan one year. systems shall be designed and operated able asbestos materials that hare > (B> For each planned renovating op to capture the asbestoe particulate mat removed or stripped: eration not covered by paragraph (d) (3) ter produced by the stripping of friable (iv) The portion of the structure b (D (A), the totaj amount of friable as asbestos material. There shall be no demolished that contains friable as bestos material that can be predicted -visible emissions to. the outside air from tos materials shall be adequately wt will be removed or stripped at a source. such local exhaust-ventilation and col during the wrecking operation. (11) For purposes of determining lection systems except as provided in . (e) - whether sa emergency renovating op naraxraoh (f) of this section. (2) Any "owner or operator who i eration constitutes a renovation within (v) All friable asbestos materials that tends to spray asbestos materials whl the meaning of this paragraph, the amount of friable asbestos material to have been removed or stripped shell be adequately wetted to-ensure that such contain more than 1 percent asbestos a dry weight basis to insulate or firepre be removed or stripped shall be the total materials remain w*t-during all remain equipment and machinery shall repc amount of friable asbestos material that ing stages of demolition or renovation such intention to the Administrator win be removed or stripped as a result and related operations. Such least 20 days prior to the commenceme of the suddsa, unexpected event that materials shall not be dropped or thrown of the spraying operation. Such re necessitated the renovation. - v (4) The following procedures than be to the ground or a lower floor. Such meterlels that have -been removed or shall include the following informs a ( used to prevent emissions of particulate stripped ' more than- - 20 feet above (f) Rather than meet the no-vi asbestoe material to outside air: - ground level, except those materials re emission requirements as specific (1) Friable asbestos materials, used to insulate -or fireproof any pipe, duct, boiler, tank, reactor, turbine, furnace, or structural member, shall be removed from any building, structure, facility or * installation subject to this paragraph. Such removal than occur before wreck moved as units or in asctions. shall be transported to the ground via dust-tight chutes or container*; - . (vi) Except as specified below, the wet ting requirements of this paragraph are suspended when tbs temperature-at ths point of wetting ir below o*C (32*F>. paragraphs (a), (c), (d). (e), (h) and <k) of this section, an owner c erator may elect to use the methods ifled by 4 61-23 to clean emissions tabling particulate asbestos materi fore such emissions escape to, o vented to, the outside air. ing or dismantling of any portion of When friable ssbestc* materials sre not - -(g) Where the presence of uneom such building, structure, facility, or in wetted due to frisslng temperatures, such water is ths sole reason for faili stallation that would break up the fri materials on pipes, duets, boilers, tanks, meet the no-vislble-emiision re able asbestoe materials end before reactors, turbines, furnaces, or structural meat of paragraphs (a), (c), (d: VCOOUU MOtSTR, VOL 40, M. lee--WWDar, OCTOm IS, 1V7S *; l , ' - " 'i-" ' - 0006127 * - '*** i RULES AND REGULATIONS - 48299- 2. The authority citation at the end of the table ot sections tor Bart 61 ia revised to read aa tQUewa: . ' ATmoaorr See*. 113 and U4oC the Claes Air Act, a amaadad by eee. 4(a) at rub. L. dona in which load-supporting struc tural members are wrecked or taken out Are excluded. *. (n) "Elsnned renovation" means a renovation operation, or a number of prohibited, except for temporary road ways on an area of asbastae ore deposits. The deposition of asbestos tailings or aabestoe-containing waste . on roadways covered with snow or low la oansldtred ' 91-404, M Stafc 1473 (<3 17JSAJ. Uglo-7, 1U7 such operations, in which the amount "surfacing." ' c-9). . of friable asbestos material that will be (c) Manufacturing: Thera be no Subpart A---General Tnwlejmn 3. Section 81.14 is amended by revising removed or stripi>ed within a given pe riod of time can be predicted. Operations that are individually non-scheduled are visible-emissions, .to the outride air. ex cept aa provided in paragraph (t) of this section, from any of the following op paragraph (c) and adding paragraph included, provided a number of such op erations if they use commercial asbeatos (d). The revised and added paragraphs erations can be predicted to occur during- or from any building or structure In read as follows: - a given period of timebased on operating, which such operations are conducted. * 61.14 Source teat and analytical meth od*. . . . - * ' m (c) The Administrator may, after no tice to the owner or operator, withdraw approval of an alternative method granted under paragraphs (a), (b) or (d> of this section. Where the test results using an alternative method-do not ade quately indicate whether a source is in compliance with a standard, the Ad ministrator may require the use of the reference method or its equivalent <d) Method 105 in Appendix B to this part is hereby approved by tbs Adminis trator aa an alternative method for sources subject to 81.52(b). 4. A new 161.17 is added to subpart A as follows: : 61.17 Circumvention. ' * ' No owner or operator subject to the provisions of this part shall build, erect, install, or use any article, machine, equipment process, or method, the use of which conceals an emission which would otherwise constitute a violation of an applicable standard. Such concealment includes, but is not limited to, the use of gaseous dilutants to achieve compliance with a visible emissions standard, and the piecemeal carrying out of an opera tion to avoid coverage by astandard that applies only to operations larger than a specifiedsiie. .- .. . Subpart 8- -National Emission Standard experience. - - (o) "Emergency renovation" a -renovation operation that results from a sudden, unexpected event, and is not-* planned renovation. Operations necessi tated by non-routine failures of equip ment are included. - - - <p> "Adequately wetted." means suf ficiently mixed or coated with water or an aqueous solution- to prevent dust emissions. - . . (q) "Removing" means taking out fri able asbeatoe materials used to insulate or fireproof any pipe, duct, boiler, tank, reactor, turbine, furnace, or structural member from any building, structure, facility, or installation. - (r) "Stripping" means taking off fri able asbestos materials used for Insula tion or fireproofing from any pipe, duct, boiler, tank, reactor, turbine, furnace, or structural member. (s) "Fabricating" means any process ing of a manufactured product contain ing commercial asbestos, with the ex ception of processing at temporary sites for the construction or restoration of buildings, structures, facilities or instal lations. ' (t) "Inactive waste disposal site" means any disposal site or portion thereof where additional asbestos-con taining waste material will not be depos ited and where the surface is not dis turbed by vehicular traffic. <u> "Active waste disposal site" means any disposal site other than an inactive (10) The manufacture of' shotgun ` shells. , (11) The manufacture of asphalt con crete. ' (d) Demolition and renovation: The requirements of this paragraph shall apply to any owner or operator of a ' demolition or renovation operation who- intends to demolish any Institutional, commercial, or industrial building-tin- . eluding apartment buildings having more than four dwelling unite), structure. . facility, installation, or portion thereof which contains any pipe, duct; boiler, tank, reactor, turbine, furnace,-or struc tural member that is insulated or fire- ' proofed with friable asbestos material, except as provided in paragraph <d> U) of this section; or who intends to reno vate any institutional, commercial, or In dustrial building, structure, facility, in stallation, or portion thereof where more than 80 meters (ca. 260 feet) of pipe in sulated or fireproofed with friable as bestos material are stripped or removed, or more than 15 square meters (ca. 180 square feet) of friable asbestos material used to Insulate or fireproof any duct, boiler, task, reactor, turbine, furnace, or structural member are stripped oh re moved. .* (1) (i> The owner or operator of a demolition operation is exempted from tha requirements of this paragraph pro- vided, (1) the amount of friable asbestos material in tha building or potion ' - . forAsbestoe - - cite.. - *: thereof to bo demolished is lees than 80 . 5. Section 61.21 is amended by revising paragraph (j> and adding paragraphs (k), (1), (m>, (n), (o), (p), (q), (r), (s). (t), (u), (v), and (w). The-revised and added paragraphs read aa follows: 61.21 Definitions- -- ' (v) "Roadways" means surfaces on which motor vehicles travel including, but not limited to.. highways, roads, streets, parking areas, and driveways. (w) "Asbestos-containing waste mate rial" means eny waste which contains commercial asbestos and is generated by a source subject to the. provisions of this meters (ca. 260 feet) used to insulate pipes, and less than 15 square maters <ca. 160 square feet) used to Insulate or fire proof any duct, boiler, tank, reactor, tur bine, furnace, or structural member, and (2) the notification requirements-of par agraph <d) (1) (il) are met * (ID Written notification shah be post ' (j) "Demolition" means the wrecking subpart,'including asbestos mill tailings, marked or delivered to the Administrator or taking out of any load-supporting control device asbestos waste, friable as at least 20 days pridr to commencement structural member and any reiatad re bestos waste material, and bags or con of demolition and shall include the in moving or stripping of friable asbestos tainers that previously contained-com formation required by paragraph (d) (2) materials. . * mercial asbeatos. of this section, with the exception of the . - (k) "Friable asbestos material" means <ny material that contains more than 1 percent asbestos by weight and that can be crumbled, pulverised, or reduced to' Powder, when dry. by hand pressure. (l) "Control device asbestos waste" means any asbestos-containing waste 6. Section 61.22 is amended by amend ing-paragraphs (c) and (#>. revising paragraphs (b), (d). (f), and (g) and a^riinf paragraphs (h), (i), <J>, (to, and (1). Tha revised and added paragraphs read as follows: . information required by paragraphs (d) . (2) (iii), (vi). (vii), (viii). and (ix>, and shall state the measured or estimated amount of friable asbestos material used for insulation and fireproofing which is present. Techniques of estimation shall be explained.- \, , material that is collected in a pollution g 61.22 Emission standard. (2) Written notice of intention to de- control device. : moiwh or renovate shall be provided to (m) "Renovation" means the remov Cb> Roadways: The surfacing of road the Administratorby the owneror opera ing or stripping of friable asbestos mate- ways with asbestos tailings or with as tor of the demolition or renovation oper Hal used to Insulate or fireproof any bestos-containing waste that is gener ation. Such notice shall be postmarked-- Pipe, duct, boiler, tank, reactor, turbine, ated by any source subject to paragraphs or delivered to the Administrator at least furnace, or structural member. Opera- (ch (d), (e) or (h) of this section is 10 days prior to commencement of demo- Ftaiui kioimx, YOU 40, NO. :9t--TUIiOAT, OCTOMft 14, 1*73 0006126