Document rB1V3qxx53rL28ZMzB4o6rgRe

446 CHAPTER 30 1960 Guide Report No. 1491--Further studies of the thermal characteris tics of plaster panels (ASHVE Transactions, Vol. 59, 1953, p. 511). H. B. Nottage, C. V. Franks, L. E. Hulbert, and L. F. Scbutrum: ASHVE Research Repost No. 1492--Heat flow analy sis in panel beating or cooling sections, case II--Floor slab on earth with uniformly spaced pipes or tubes at the slab-earth interface (ASHVE Transactions, Vol. 59,1953, p. 527). C. M. Humphreys, H. B. Nottage, C. V. Franks, R. G. Hueb- scher b. F. Sehutrum, and D- W. Locklin: ASHVE Research Report No. 1387--Laboratory studies on heat flow within a concrete panel (ASHVE Transactions, Vol. 56,1950, p. 175). L. F. Sehutrum and T. C. Min: ASHAE Research Report No. 1598--Cold wall effects in a ceiling-paoel-heated room (ASHAE Transactions, Vol. 63,1957, p. 187). E. L. Sartain and W. S. Harris: Performance of covered hot water floor panels, Part II--Room conditions (ASHAE Trans actions, Vol. 63, 1957, p. 209). CHAPTER 31 PIPE, FITTINGS, WELDING Pipe Motericis, Types of Pipe, Commercial Pipe Dimension*, Threading Practice, Pipe Fittings, Flange Facings and Gaskets, Valves, Welding, Expansion and Flexibility, Hangers and Supports IMPORTANT considerations in the selection and installa tion of pipe and fittings for heating, ventilating, and air conditioning are dealt with in this chapter. PIPE MATERIALS Use of corrosion-resistant materials for pipe, including special alloy steels, copper, and red brass, has increased considerably during the past few years. The following brief discusion indicates the variety of pipe materials and the types of pipe available. Wrought-Steel Pipe. Because of its lower cost, the great bulk of wrought pipe used for heating and ventilating work at the present time is of wrought steel. The material used for steel pipe is a mild steel made by the acid-bessemer, the open-hearth, or the electric-furnace process. Ordinary wrought-steel pipe is made either by shaping sheets of metal into cylindrical form and welding the edges together, or by forming or drawing from a solid billet. The former is known as welded pipe, the latter as seamless pipe. Many types of welded pipe are available, although the smaller sizes most frequently used in heating and ventilating work are made by . the lap-weld, resistance-weld, or butt weld process. While the lap-weld and resistance-weld" proc esses produce a better weld than the butt type, lap-weld and resistance-weld pipe are seldom manufactured in nominal pipe sizes less than 2 in. Seamless pipe can be obtained in the small sizes at a somewhat higher cost, and is listed as pres sure tubing below 2 in. Seamless steel pipe is frequently used for high-pressure work or where pipe is desired for close coiling, cold bending, or other severe forming operations. Its advantages are its greater strength which permits use of a thinner wall and, in the small sizes, its freedom from the occasional tendency of welded pipe to split at the weld when bent. Wrought-iron Pipe. Wrought-iron pipe may be identified by the spiral line marked into each length' either knurled into the metal or painted on it in red or other bright color. Otherwise, there is little difference in the appearance of wrought-iron and steel pipe, although microscopic examina tion of polished and etched specimens will readily disclose different grain structures. Cast-Ferrous Pipe. There are now available several types of cast-ferrous metal pipe made of a good grade of castiron with or without additions of nickel, chromium, or other alloy. This pipe is available in sizes from 114 in. to 6 in., and in standard lengths of 5 or 6 ft, with external and internal diameters closely approximating those of extra strong wrought pipe. Cast-ferrous pipe may be obtained coupled, beveled for welding, of with ends plain or grooved for the several types of couplings. It is easily cut and threaded as well as welded. The fact that it is readily welded enables the manufacturers to supply the pipe in any lengths practicable for handling Alloy Metal Pipe. Both iron and steel pipe are available in .the alloy class. In the case of iron pipe when copper and molybdenum are added, the material is known as alloy wrought-iron pipe. By common custom steel is considered to be an alloy when the maximum range of alloying elements exceed certain limits such as 1.65 percent manganese, 0.60 silicon, or 0.60 - copper. Also, a steel is an alloy if any of the following ele ments are specified in minimal quantities or within limits: Al, B, Cr (up to 3.99), Co, Cb, Mo, Ni, H, W, V, Zr, or any other element added to obtain a certain alloying effect. Small quantities of certain elements are present in alloy steels and are considered as incidental and may be present to the following maximum amounts: copper--0.35 percent, nickel--0.25 percent, chromium--0.20 percent, and molyb denum--0.06 percent. Commercially, steel is considered stainless when chromium exceeds 3.99 percent regardless of the inclusion of other al loying elements. With tubing, however, an alloy becomes stainless when it contains a minimum of 10.5 percent chro mium. The alloy and stainless steels are used for high tempera ture piping and for highly corrosive fluids and gases. Copper Pipe and Fittings. Owing to inherent resistance to corrosion, copper and red brass pipe have always been used in heating, ventilating, and water supply installations, but the cost with standard dimensions for threaded connections has been high. The introduction of fittings which permit erec tion by soldering or sweating, allows the use of tube with thinner walls than would be possible with threaded con nections, thereby reducing the cost of installations COMMERCIAL PIPE DIMENSIONS Commercial pipe dimensions are covered in the following specifications of the American Society for Testing Materials: (1) steel--ASTM A-120 and A-53, (2) wrought iron--ASTM A-72, and (3) copper tube--ASTM A-88. Tables 1 and 2 are based on these specifications. In addition to the specifications for these three materials, there are standards for copper or red brass IPS, clay or con crete, and cast-iron pipe. Copies of the following specifica tions may be obtained from the American Society for Testing Materials: (1) steel, wrought-iron, and cast-iron--Series A, (2) copper and red brass--Series B, and (3) clay and con crete--Series C. Table 3 lists the sizes available in each of the specifications and classes of steel pipe. Note that'butt-weld is not available above 4-in. size and that lap-weld, electric-resistance-weld, and fiftamlftss are not available below 2-in. size. /' 447