Document qM170GbZ1qe6D3DpoDdpbvpn

Registers and Grilles Hart & Cooley Manufacturing Co. Established 1901 Air Conditioning Registers and Grilles - Warm Air Registers Damper Regulators - Furnace Regulators - Pulleys - Chain Engineering Office and Factory Holland, Mich. Chicago Office: 61 West Kinzie Street Seven Complete Lines of Air Conditioning Registers and Grilles in Five Distinct Price Groups. THE ACE OF AIR CONDITIONING GRILLES No. 90 DESIGN Dual Control Directional Flow No. 90 Design--Made up of a number of thin strips which are shaped into a series of grooves--straight or curved--as shown. The assembled strips form an exceptionally attractive grille with openings of 34 in. and a depth of 1 in. A wide range of deflec tions is available. The tubular shape of the openings insures positive control of air flow with all deflections. Price Group E. CHARACTERISTICS OF No. 90 DESIGN 1. Dual Control of Air Flow--The air is controlled in two planes; horizontally as well as sideways. Thus, on high sidewall installations, the air is prevented from striking the ceiling, thus avoiding discoloration and loss of directional flow. WWW 2. Resistance--Curved shape of tubes eliminates tur bulence; hence, resistance is remarkably low. 3. Noise--The absence of turbulence likewise eliminates Straight Curved the greatest cause of noise in the grille. See H & C Catalog No. 37AC for Acoustica Ratings. 4. Concealment of Duct--The 1 in. depth of the grille, plus the tubular shape of the openings, results in exceptional concealment of the duct. 5. Free Area--The free area of No. 90 Grille is exceptionally large. See Page 39 of H & C Catalog No. 37AC, or Page 74 of Catalog No. 37 for Actual Free Areas. 6. Types of Directional Flow--Practically any deflections or combination of de flections are available. See Page 9 of H & C Catalog No. 37AC, or Page 65 of Catalog No. 37 for standard types of deflections. .................................. iiimiimiiimiiiiiiiiiif No. 68 Design--A very inexpensive grille combining ample free area, attractive appearance and effective concealment' of the duct. Openings are % inches by % inches with inch frets. Price Group AA. iimiiiiiiiiiMiiiiiimin No. 88 DESIGN . Perforated Plain Lattice No. 72 Design--Combines rigid bar type con struction, neat appearance, maximum free area with low cost. Depth of bars is in. Price Group A. 1070 No. 7 DESIGN Non-Adjuslable Vertical Bar Open Mesh Hart & Cooley Manufacturing Co. Registers and Grilles Nos. 84 and 85 De signs--Adjustable deflection grilles with bars % in. in depth and spaced 34 in. apart--bars are con nected in 2 in. sections, No. S4 DESIGN a. llowing_ sectional. ad- _N__o_.___S_o___D_ _E__S__IGN Adjustable Vertical Bar Close Mesh justment^ The Unique Adjustable Horizontal Bar Close Mesh construction assures positive directional control of air flow with quick adjustability to any combination of deflections desired. Depth of bars and close spacing combine attractive appearance and concealment of the duct. Price group D. Nos. 77 and 78 Designs--Fixed air flow. Similar in appearance to Nos. 84 and 85 Designs. Price Group B. REGISTER AND GRILLE FRAMES Any of the grille designs shown are available with any of the installation frames listed below. OUTER MEMBER 333fr No. 3 SIDEWALL STUD FRAME (Left) Installations when made as recom mended with this frame are perma nently streakproof. The frame provides a positive plaster lock, preventing the plaster from pulling |NMEB f away from the frame. The register face overlaps the frame 34 in. on all sizes. The Sponge Rubber Gasket which is furnished attached to the register face, forms a seal between the wall and the register face, pre venting air leakage at this point. The frame has rigid supporting arms of sufficient length on all sizes to fasten directly to the studs. The stackhead is bent over the outer member of the frame and held in place by means of the inner member. No. 8 BASEBOARD STUD FRAME (Right) Extension arms fasten directly to studs. Stackhead is attached to frame either by forming over inner member or by clamping it between the outer and inner members. May be used with any H & C one-piece Baseboard Register, all of which are furnished with Sponge Rubber Gas ket as standard to prevent streaking. Frame insures a solid foundation for register and protects stackhead. In expensive, easy to install. Schedule of Class Numbers for Use in Specifying H&C Registers, Grilles, and Intakes Type of Frame Grille only, or Return Air Intake. Flat.................. Register without installation frame......................... Sidewall Register with No. 2 Band Iron Frame.. Sidewall Register with No. 3 Stud Frame............. Baseboard Register with Integral Frame............. Baseboard Register with No. 5 Stack Frame.. .. Intake with 7/g-tn. projection..................................... Baseboard Register with No. 8 Stud Frame......... Design No. 68 1 72 77 78 84 85 90 721680 1 720 770 780 840 850 900 681 771 781 841 851 901 682 722 772 782 842 852 902 683 ! 723 773 783 843 853 903 684 j 724 774 784 844 854 904 68 5 i 725 775 785 845 855 905 687 1 727 688 i 728 777 778 787 788 847 848 857 858 907 908 Complete Separate Catalogs on Air Conditioning Registers and Grilles or Warm Air Registers Available on Request. 1071