Document o9kveZL14VdwVKzZp7w7nOYY7

2?8 CHAPTER 12 1958 Guide{ V = coefficient of transmission, air to air, Btu per (hour) (square foot) (Fahr enheit degree temperature difference) (Chapter 9). ii -- indoor temperature near surface involved (this may not necessarily be the sorcalled breathing line temperature), Fahrenheit degrees. to 5=3 outdoor temperature, or temperature of adjacent unheated space or of the ground, Fahrenheit degrees. Example 4' Calculate the transmission loss through an 8 in. brick wall having an area of 150 sq ft, if the inside temperature t\ is 70 F and the outside temperature L is - 10 F. Solution: The coefficient of transmission (U) of a plain 8 in. brick wall is 0.41 (Chapter 9, Table 8). The area (A) is 150 sq ft. Substituting in Equation 4: Ht = 150 X 0.41 X [70 - (-10)] = 49200 Btu per hour. Table 6. Floor Heat Loss to be Used When Warm-Air Perimeter Heating Ducts Are Embedded in Slab Btu per (hour) (linear foot of heated edge) Outdoob Design Temperature,F Edge Insulation 1-in. Vertical Extend ing Down 18 in. Below Floor Surface 1-in. L-Type Extend ing at Least 12 in. Deep and 12 in. Under 2-in. L-Type Extend ing at Least 12 in. Down and 12 in. Undeb -20 -10 .0 10 20 105 95 . , 85 75 62 100 90 80 70 57 85 75 65 55 45 * Factors include lo6s downward through inner area of slab. Transmission Loss Through Ceilings and Roofs The transmission heat loss through top floor ceilings, attics, and roofs may be estimated by either of two methods: 1 n 1. By substituting in Equation 4 the ceiling area A, the inside-outside tempera ture difference (ti -- t0) and the proper value of U: ,;i SL.^Flat roofs. Select the coefficient of transmission of the ceiling and roof from'-.' Tables 11 to 14, Chapter 9, or use appropriate coefficients in Equation 1 if side', walls extend appreciably above the ceiling of the floor below. :J b. Pitched roofs. Select the combined roof and ceiling coefficient from Table 1$ Chapter 9 or calculate the combined roof and ceiling coefficient by means of Equations 4 and 5, Chapter 9, where these formulas are applicable as explained in Chapter 9. 2. By estimating the attic temperature (based on the inside and outside designtemperatures) by means of Equation 1, and substituting for (,, in Equation 4, the' value of tD thus obtained, together with the ceiling area A and the ceiling coefficients U. This applies to pitched roofs. In the case of fiat roofs it is not necessary to calculate the attic temperatures, as the ceiling-roof heat loss can be determined as, suggested in paragraph la. INFILTRATION HEAT LOSS The infiltration heat loss includes (1) the sensible heat loss or the heat-, required to warm the outside air entering by infiltration, and (2) the latenl\ heal loss or the heat equivalent of any moisture which must be added. Heating Load 279 Sensible Heat Loss The formula for the heat required to warm the outside air which enters a room by infiltration to the temperature of the room, is given in Equation 5: B, = 0.240 Qd (ti -- f0) (5) where B, = heat required to raise temperature of air leaking into building from t,, to U, Btu per hour. 0.240 = specific heat of air. Q = volume of outdoor air entering building, cubic feet per hour (see Chap ter 11). d -- density of air at temperature t0, pounds per cubic foot. It is sufficiently accurate to use d. -- 0.075 in which case Equation 5 reduces to H. = 0.018 Q (U - <,,) (5a) The volume Q of outside air entering per hour depends on the wind velocity and direction, the width of crack or size of openings, the type of openings and other factors, as explained in Chapter 11. Where the crack method is used for estimating leakage, it is more convenient to express the air leakage heat loss in terms of the crack length: where B. = B L (t; - l0) (5b) B = air leakage per (hour) (foot of crack) (Chapter 11) for the wind velocity and type of windows or door crack involved, multiplied by 0.018. L = length of window or door crack to be taken into consideration, feet. Example 5: What is the infiltration heat loss per hour through the crack of a 3 x 5 ft average, double-hung, non-weatherstripped, wood window, based on a wind velocity of 15 mph? Assume inside and outside temperatures to be 70 F and zero, respectively. Solution: According to Table 2, Chapter 11, the air leakage through a window of this type (based on iV in. crack and A in. clearance) is 39 cu ft per (ft of crack) (hour). Therefore, B = 39 X 0.018 = 0.70. The length of crack L is (2 X 5) + (5 X 3), or 19 ft; q = 70 and t, = 0. Substituting in Equation 5b, B. = 0.70 X 19 X (70 - 0) = 931 Btu per hour. Crack Length to be Used for Computations is ^rf^?f'gners wh prefer to use the crack method, the basis of calculation as follows: The amount of crack used for computing the infiltration out'H S s*10u^ be not less than half of the total length of crack in the in fh wa^s the room. For a building having no partitions, air entererf ,TMrouh the cracks on the windward side must leave through the com tn ^le *eewar(l side. Therefore, take one-half the total crack for wallet eah side and end of the building. In a room with one exposed > ake all the crack; with two exposed walls, take the wall having the