Document nmYxymOLjoV83E3bXojRr8LVR

Insulation Bushings, Inc. Coolidge at 14 Mile Road, Royal Oak, Mich. VIBRO-LEVELERS: ltubbcr-in-shear vibration dampner and preci sion leveier stop vibration and level machinery. Recommended for New or Existing: Air Conditioning Units, Refrigeration Units, Com pressors, Blowers, Diamond Borers, Buffers-Polishers, Punch Presses, Broaching Machines, Vacuum Pumps, Forging Hammers, Tool Room Grinding Machines, etc. Catalog No. Bu. 60 Mouting Number Load Capac ity of Each Mounting (Pounds) 3010 10 3025 25 3050 50 3100 100 3200 2003300 300 3400 400 3500 500 3750 750 4000 1000 4150 1500 4200 2000 Usually installed 4 per machine. Any number may be used to suit machinery re quiring more (or fewer) points of sus pension. VIBRO-LEVELERS Have These 6 Important Features: (1) Rubber-in-shear Vibra tion Dampner and Precision Leveier; (2) Ease of Installation; (3) No special parts required; (4) No tapping or fitting (Vibro-Levelers come complete); (5) No floor cutting (and floor repair); (6) Low Cost. Vibro-Leveler (Dual Purpose Machinery Mountings that stop vibration transmis sion and level machines) are as simple in design and construction as they are easy to install. An inner cylinder with the stud, is insulated from the outer shell by a wall of mechanically bonded rubber. They have an ample safety margin. Overloaded to destruction they will allow a drop of less than in. Installation Vibro-Levelers are usually installed under the machine. The machine is either raised or tilted enough to let the Vibro-Leveler be slipped under the base and to allow the stud to be inserted into the hold-down bolt hole in the base of the ma chine. The lower nut is turned to bring the machine to exact level and the upper nut locks it in position.. The Vibro-Levelers come complete even to the leveling and locking nuts; no fitting, no cutting, no threading of any kind is required. Where the machine must be kept at or near the original level, brackets are either bolted or welded to the side of the base. Ordinary structural brackets are ideal for this. 1354 The Celotex Corporation General Offices 120 South LaSalle Street, Chicago 3 Insulation Celotex Cane Fibre Insulation prod ucts are made by felting the long, tough fibres of bagasse into strong, rigid boards. They are manufactured under the Ferox Process (patented) which ef fectively protects them from destruction bv termites, fungus growth, and dry rot. They are integrally water-proofed which insures a non-hygroscopic insulation of low capillarity and enduring insulating efficiency. Celotex Insulating Sheathing An insulating, weathcr-resistingsheathing for use under any type of exterior. Surfaces and edges are moisture-proofed with a surface impregnation of asphalt. Sizes: in. thick: 4 ft wide: 8 ft, 9 ft, 10 ft and 12 ft long. Also 2 ft x 8 ft with long edges--center matched. Vapor-seal Roof Insulation--An im proved type of water resistant cane fibreboard coated with high grade asphalt and having offsets on all edges so that when applied a network of channels next to the roof deck provides a means of equal izing the air pressure therein. Size: 24 in. x 48 in.; thickness: 1 in., 1A in. and 2 in. Cemesto A completely fabricated fire and mois ture resistant structural insulating wall unit. Consists of a Celotex cane fiber core surfaced on both sides with a A in. layer of asbestos-cement board. The established low thermal conductivity of the Celotex core is maintained in the manufacture of Cemesto. Sizes: 4 ft x 4 ft, 4 ft x 6 ft, 4 ft x 8 ft, 4 ft x 10 ft, 4 ft x 12 ft; thicknesses: 1A in., 1& in. and 2 in. Celotex Insulating.Lath Regular Insulating Lath.--A cane fibre faster base of high insulating efficiency. urface provides a strong bond for plas ter and the bevelled edges and ship-lap joint provide additional reinforcement. Size: 18 in. x 48 in.; thickness: A in. Celo-Block Celo-Block Cold Storage Insulation consists of low density cane fibre- boards bonded together with asphalt mastic and surfaced front and back with asphalt. Celo-Block has excellent in sulating qualities. Size: 12 in. x 36 in. or 18 in. x 36 in.; thickness: 2 in. and 3 in. Celotex Roof Insulation Products Regular Roof Insulation--A cane fibre product possessing superior insulating properties. It reduces roof heat trans mission as shown by coefficients estab lished in The Guide; reduces roof move ment due to contraction and expansion. Size: 23 in. x 47 in. or 24 in. x 48 in.; thickness: A in*, 1 in., 1A in. and 2 in. Preseal Roof Insulation--A cane fibre product coated with a special asphalt for moisture protection on the job. Size: 23 in. x47 in., or 24 in. x 48 in.; thickness: A in., 1 in., 1A in. and 2 in. Celotex Rock Wool Products Available in the following forms-- Loose, Granulated, and Paper-backed Batts. Celotex Rock Wool is made from the clean fibres of molten rock. In combustible and integrally waterproofed. Q-T Ductliner An acoustical material designed espe cially for duct lining in air conditioning systems. Absorbs duct noises. Made of rock wool and a special binder. De signed to withstand air duct humidity conditions. Is fire resistant and will not smoulder or support combustion. Ther mal conductivity of 0.30. 1355