Document mqV15XwBMVYYz0dY3q2r1KzXB

Heating Ventii>ating Air Conditioning Guide 1939 perature results in an increase in length of the pipe for which provision must be made. The amount of linear expansion (or contraction in the case of refrigeration lines) per unit length of material per degree change in temperature is termed the coefficient of linear expansion of that material or commonly, the coefficient of expansion. This coefficient varies with the material. The linear expansion of cast iron, steel, wrought iron, and copper pipe Table 4. Nominal Weights of Welded Wrought-Iron Pipe Nominal Pipe Size (Inches) a 1 mm 2 2H 3 314 4 5 6 8 10 12 14 O. D. 16 O. D. 18 0. D. 20 O. D. SCHED. SCHED. 10 20 Plain Plain Ends ' Ends 36.0 41.3 46.5 44.8 51.4 57.9 77.0 Schedule 30 Schedule 40 Schedule 60 Plain Threads Plain Threads Plain ' K.nria Couplings Knijg Couplings F.nris 24.7* 34.3* 43.8* 53.6 61.4 80.5 103.0 25.6* 35.0* 45.0* -- 0.25* 0.25* 0.43* 0.43* 0.57* 0.57* 0.86* 0.86* 1.14* 1.14* 1.68* 1.69* 2.28* 2.29* 2.72* 2.74* 3.66* 3.68* 5.80* 5.82* 7.58* 7.62* 9.11* 9.21* 10.8* ,10.9* 14.7* 14.9* 19.0* 19.2* 28.6* 28.8* 40.5* 41.2* 53.6 55.0 ' 62.2 81.2 103.0 115.0 -- 54.8* 73.2 87.6 111.0 136.0 Plain Rniig Weights are given in pounds per linear foot and are for pipe with plain ends except for sizes which are commercially available with threads and couplings for which both weights are listed. Weights marked with an asterisk in Schedules 30 and 40 are identical with weights for standard-weight pipe in former lists; those in Schedules 60 and 80 are identical with weights for extra-strong pipe in former lists. ^ The Schedule Numbers indicate approximate Values of the expression 1000 x P/S. the materials most frequently used in heating and ventilating work, can be determined from Table 6. The elongation values in Table 6 were computed from the .following formula: where - Lt = length at temperature t degrees Fahrenheit, feet. to = length at 32 F, feet. t = final temperature, degrees Fahrenheit. a and b are constants as given on the next page. 366. Charter 18. Pipe, Fittings, Welding Cast-Iron........ SWtreoeulg--h---t-I-r.o..n.. Copper---------- 0.005441 0.006212 0.006503 0.009278 0.001747 0.001623 0.001622 0.001244 The three methods by which the elongation due to thermal expansion may be taken care of are: 1. Expansion joints. 2. Swivel joints. . . 3 Inherent flexibility of the pipe itself utilized through pipe bends, right-angle turns, or offsets in the line. Table 5. Standard Dimensions, Weights, and Diameter and Wall Thickness Tolerances for Copper Water Tubes* (All Tolerances Plus and Minus) Permissible Actual Outside & Diam eter, Variation in Mean Outside Diameter, In. In. Annealed Hard Drawn WALL THICKNESS, IN. Clam K Class L Class M Per Per Per Nominal missible Varia Nominal missible Varia Nominal missible Varia tion tion tion Weight per Ft Lb ClKass Class L Class M Vs 0.500 0.0025 0.001 0.049 0.004 0.035 0.0035 0.025 0.0025 0.269 0.198 0.144 14 0.625 0.0025 0.001 0.049 0.004 0.040 0.0035 0.028 0.0025 0.344 0.285 0.203 Vi 0.875 0.003 0.001 0.065 0.0045 0.045 0.004 0.032 0.003 0.641 0.455 0.328 1 1.125 0.003S 0.0015 0.065 0.0045 0.050 0.004 0.035 0.0035 0.839 0.655 .0.464 IK 1.375 0.004 0.0015 0.065 0.0045 0.055 0.0045 0.042 0.0035 1.04 0.884 0.681 IK 1.625 0.0045 0.002 0.072 0.005 0.060 0.0045 0.049 0.004 1.36 1.14 0.94 2 2.125 0.005 0.002 0.083 0.005 0.070 0.005 0.058 0.0045 2.06 1.75 1.46 2K 2.625 0.005 0.002 0.095 0.005 0.080 0.005 0.065 0.0045 2.92 2.48 2.03 3 3.125 0.005 0.002 0.109 0.005 0.090 0.005 0.072 0.0045 4.00 3.33 2.68 3K 3.625 0.005 0.002 0.120 0.005 0.100 0.005 0.083 0.005 5.12 4.29 3.58 4 4.125 0.005 0.002 0.134 0.006 0.110 0.005 0.095 0.005 6.51 5.38 4.66 5 5.125 0.005 0.002 0.160 0.006 0.125 0.006 0.109 0.005 9.67 7.61 6.65 6 6.125 0.005 0.002 0.192 0.006 0.140 0.006 0.122 0.005 13.87 10.20 8.91 From Standard Specifications for Copper Water Tube of the American Society far Testing Materials, AS.T.M. Designation B88-33. Expansion joints of the slip-sleeve, diaphragm, or corrugated types made of copper, rubber, or other gasket material are all used for taking up expansion, but generally only for low pressures or where the inherent flexibility of the pipe cannot readily be used as in underground steam or hot water distribution lines. Swivel joints are used extensively in low-pressure steam and hot water heating systems and in hot water supply lines. The swivel joints absorb the expansive movement of. the pipe by the turning of threaded joints. In many cases the straight pipe in the offset of a swivel joint is sufficiently flexible to take up the expansion without developing enough thrust to produce swiveling in the threaded joint. This is preferable since con- 367