Document mMYvzv4kQz09OEGwYoEGd8xb

200 Air System Equipment spray Names Monarch Manufacturing Works, Inc. 2509 E. Ontario St., Philadelphia 34, Pa. SPRAY NOZZLES FOR WATER AND OIL NON-CLOG AIR WASHER NOZZLES Produce an exceptionally efficient, evenly distributed hollow cone spray. Single large tangential inlet to swirling chamber minimizes any possibility of clogging. Also available in Vs in. to 1 in. pipe sizes inclusive, and of Brass, Stainless and Monti. Pipe Size and Fig- No- Water Capacities: Gallons per Hoar Operating Pressure; Lb per Square Inch Orifice Lead 5 10 20 30 40 60 so too H in. Fig. 629 or 69 61 61 53 49 69 2.7 3.3 3.8 4.7 5.4 6.0 61 4.2 51 5.9 7.2 8-3 9.2 53 2.7 3.7 5.3 6.5 7.5 9.2 10.5 11.8 53 4.0 5.7 8.2 10.0 11.5 14.1 16.3 18.2 49 5.6 7.9 11.1 13.6 15.7 19.3 22.2 24.8 H in. Fig. 629 or Fig. 631 Ht X X X *X* Xt 9.6 13.5 19.2 23.4 27.0 33.0 38.4 42.9 Ha 12.2 17.3 24.4 29.9 34.6 42.4 49.0 54.9 X* 14.6 20.6 29.1 35.7 41.0 50.4 58.4 65.1 X 15.9 22.5 31.9 39.2 45.1 55.2 63.7 71.5 X 21.7 30.6 43.2 53.0 61.1 75.0 86.4 98.0 Fig. 631 Fig. 629 AIR CONDITIONING AND OIL BURNER NOZZLES Water Capacities: Gallons per Hour Nozsle No. Operating Pressure. Lb per Square Inch 25 40 60 so 100 Min, Pressure (PSD 1.35 1.65 2.00 2.60 3.00 3.50 4.00 4.50 5.00 5.50 6.00 7.00 1.00 i.30 1.50 1.90 2.20 2.40 2.60 3.00 .57 .75 .94 1.13 1.27 1.64 1.90 2.40 2.78 3.04 3.28 3.80 -70 .92 1.14 1.39 1.55 2.01 2.33 2.94 3.41 3.72 4.03 4.65 .81 1.06 1.32 1.60 1.79 2.32 2.69 3.40 3.94 4.30 4.66 5.37 .90 1.18 1.49 1.80 2.00 2.GO 3.00 3.80 4.40 4.80 5.30 6.00 40 40 35 30 25 25 20 20 20 15 15 15 Produce very effective breakup with direct pressure only. Capacities above are on water. "Nozzle No." is capacity on 34 second Saybolt vis cosity oil at 100 lb pressure. Larger sizes up to 100.00 gph and smaller sizes down to 0.40 gph, on oil. Furnished of all Brass for Water--Stainless Steel tip and disc for Oil. Standard with Ya in. or Yi in. female or Yi in. male pipe Brass adapter and Monti gauze steamer. SPRAY POND NOZZLES For recooling condenser water, etc. Operate on pres sures from 5 lb upward. Made of Cast Red Brass and in pipe sizes in., 1 in., 1 Yt in., 2 in., 2Yi in. and 3 in. Capacities from 4.1 to 134 gpm at 7 lb pressure. Write lor Detailed Catalogs 201 International Heating & Air-Conditioning Exposition Permanent Address--480 Lexington Ave., New York 17, N. Y. EXPOSITIONS HELD Philadelphia, 1959; Chicago, 1957; Philadelphia, 1955; Chicago, 1953; Philadelphia, 1951; Chicago, 1949; New York, 1948; Cleveland, 1947-1940; New York, 1938; Chicago, 1936; New York, 1934; Cleve land, 1932; Philadelphia, 1930. FUTURE SCHEDULE 15th International Heating & Air-Conditioning Ex position--International Amphitheatre, Chicago--Feb. 13-16, 1961. UNDER AUSPICES OF A.S.H.R.A.E. These biennial Expositions are held coincident with the semi-annual meetings of American Society of Heat ing, Refrigerating and Air-Conditioning Engineers, Inc., and under their auspices. Management is by Inter national Exposition Company with permanent head quarters at 480 Lexington Ave., New York 17, N. Y. EXHIBITORS Comprise Leading firms in each phase of the industry; number has varied from 150 to more than 500 exhibi tors. EXHIBITS These range from and comprise all the types of ar ticles discussed or advertised in this copy of The ASHRAE Guide. 1. The Combustion Group: Furnaces, burners (coal, oil and gas), grates, stokers, boilers, radiators (various types), refractories and auxiliaries. 2. The Oil Burner Group: 3. The Hydraulic Group: Water feeders, water heaters, pumps, traps, valves, piping, fittings, expansion joints, pipe hangers, etc. 4. The Steam Heating Group: Vapor heating, steam specialties. 5. The Hot Water Heating Group: 6. The Air Group: Warm Air furnaces and stoves, registers and grilles, cooling towers, air filters, motors, fans, blowers, condi tioning equipment, ventilators (room and industrial types), unit heaters, etc. 7. The Am Conditioning Group: Equipment which circulates and filters the air, in sum mer dehumidifies and cools; in winter heats and hu midifies, and does all these in proper season for com plete, all year-round air conditioning. 8. The Control Group: Instruments of precision for indicating, controlling or recording temperature, pressure, volume, time, flow, draft or any other function to be measured. 9. The Refrigerating Group: Compressors, condensers, cooling apparatus, contin gent apparatus and refrigerants. 10. The Central Heating Group: Apparatus and materials especially designed or adapted to the uses of central heating and central heat ing station supplies. 11. The Insulating Group: Structural insulators (refractory and cellulose mate rials), asbestos, magnesia clays and combinations thereof, pipe and conduit covering, etc., weather-strip ping, adhesives etc. 12. The Miscellaneous Group: Electric Heaters, boiler and pipe repair alloys, liquids and compounds, tools of all kinds, and equipment not specifically included in the above groups, but related thereto. 13. The Machinery and General Equipment Group. 14. Books and Publications VISITOR ATTENDANCE Attendance is by invitation and registration only, thereby presenting a selected audience. Included are engineers, contractors, dealers, jobbers, supply houses, industrial users, professional and service organizations, public utilities, real estate management concerns, etc. A detailed analysis of registered attendance is available on request. Industrial Expositions in America lead the exposi tions of the world in style, business effectiveness, in dustrial influence and educational value. This Exposi tion stands among the leaders in Industrial Expositions in America. It is an educational institution which brings together the research. developments and im provements in equipment and materials for use in heating, refrigerating, ventilating and air conditioning all types of buildings.