Document g2D77LL7DQJqJQDYKgbxej9Ve

TECHNICAL SPECIFICATIONS CertainTeedEH SPECIFICATIONS CLASSIFICATION; A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: PACE NO.: CertainTeed Corporation Pipe and Plastics Group 11 supersedes: 158 April 30, 1979 okkriftion; A/C Bureau of Reelamation/FIuId Transmissions Pipe, Couplings and Accessories 1 OATS OF ISSUE: fB l WZ 1.0 CTCTRAL ./ - CertelnTeed Corporation Pipe and Plastics Croup "Fluid Transmlsalon" (FT) pipe and "Bureau of Reclamation" (B/R) plpa l* made In nine daises snd Is used In supply systems that carry liquid under pressure. The evallable classes are FT 30 AC, 35. 40. 45, 50, 60, 70. 80, and 90 In the following pipe sizes: 6", 8", 10", 12", 14", 15", 16", 18", 20", 21", and 24", except 6" class FT 30 and 35 and 21" and 24" FT-90. Fluid Transmission and Bureau of Reclamation pipe and couplings are the same, except Fluid Transmission will be supplied with Common Groove (CG) rings, and Bureau of Reclamation will be supplied with round, rubber rings. 2.0 GEKERAL PRODUCT DESCRIPTION . Unless otherwise listed herein, refer to '"Ceneral Product Specification Data", Section D of the Ceneral Standards Manual, for information concerning the following: 1. Composition 2. Trademarks 3. Test. Methods 4. Ceneral Requirements a. Pipe length b. Lubricant c. Marking d. Installation Instructions e. Finish f. Straightness g. Leakage Allowance All Fluid Transmission pipe and couplings shall bo completely free of loose or hanging A/C chips in the Interior. Machined outer surfaces of all pipe (regardless of length), flttlng6, and adaptors shall be free of hanging machined trim (lace curtains). The Interior corner of the pipe nose shall be free of all loose or hanging chips. The approved method for cleaning the pipe interior nose is to use the I.D. bevel tool to breek this corner. 3.0 CONFORMANCE The Fluid Transmission Product line will meet the requirements of the latest Issue of: ASTH C668 - Spec, for Asbestos Cement Transmission Pipe AWWA C402 - Asbestos Cement Transmission Pipe, 18 Inches through 42 Inches for Water and Other Liquids The Bureau of Reclamation Product line (round rings) will meet the requirements of the latest Issue of: Standard Specification for Asbestos-Cement Pressure Pipe put out by the Bureau of Reclamation. CTD015438 prepared by: APPROVED BY: 02-10-0023 (P9>2277)) 12/76 cCONFIDENTIAL OOCUMENT R *D HFQ. 4- ALES I.K. OTHERS 4.0 TA.RLF. OF HYPHO 'JEST REOUIRPIFHTS Page 2 Product Standard Pipe Lengths (1) t'ich length to the pressure specified in Table A for at least five seconds without failure. (2) Additionally from each 300 pieces of each sire and class per shift of manu facturing or fraction thereof, an unmarhtucJ length of at lease one foot uust pass an Instantaneous pressure equal to ten times the cl\;s designation (see Table R). The remaining length may then be shipped if It passed a retest of part (l). If the first staple falls, two more will be tested and boih must pass or the lot is rejected. Random ?tpo.Lengths Sana a* Test (l) above. Shore Lengths (fc and \ HEO) Sarae as Test (l) above. Short Lengths (1/8, 1/4 end 1/2 FH) Same es Test (l). Standard Coupling Sane at Test (1).. Coupling Adaptor (FT to Steel) Stock to meat Test (1). Coupling Adaptor (FT to FT) Pipe Adaptors Stock to meet Test (1) for lower class. Stock to meet Teat (1) for lower class. lass 30 35 40 45 SO 60 70 60 90 TABLE A Hydro Proof Test Value 225 263 300 338 375 4S0 323 600 675 Claa. 30 35 40 45 50 60 70 80 90 TABLE B Hydro Burst ' 300 350 400 450 500 600 700 800 900 5.0 Flexural Strength Each'standard 13 foot length of pipe in sizes 6 and 8 inch shall be tested for flexural strength In accordance vlth the following table when tested in accordance with ASTM C500. FLEXURAL PROOF LOADS Total Applied Load, Lbs. 12 ft. Span Seminal Pipe Size Inches 6 8 Class 30 . 2800 Class 35 _ 3300 Class 40 Class 45 Class 50 Class 60 1700 3800 1900 4300 2100 4800 2400 5200 Claaa 70 Class 80 Claaa 90 2800 5700 3000 6600 , 3700 7600 6.0 Crush Requirements A one foot unmachlned sample shell be taken from a pipe in each size and class for each 300 lengths or portion thereof per shift of manufacturing for this test. The test shall be performed In accordance with ASTM C500. Fully machined Pipe, Threaded Couplings, and Pipe Adapters shall be capable of withstanding 75 per cent of the minimum crushing strength specified for the corresponding size and class of pipe. All other Items, particularly the couplings, shall be capable of withstanding the same minimum crush . loads as specified for the corresponding size and class of pipe. For those Items acting as connecting pieces between sizes and/or classes, the lowest minimum crush load shall apply. CTD015439 TECHNICAL SPECIFICATIONS seacirtcATioNS ctAaetPtCATtON: CertainTeedlH A/C Standard Product Specification t.c.o. nar. no. SPKClPtCATION no: PACK NO.: CertainTeed Corporation Pipe and Plastics Group 11 supaeasoss: I5B dmckiption: April 30, 1979 A/C Bureau of Reclamation/Fluid Transmission 3 DATS or isouk: FEB 1 1382 __________Pipe, Couplings and Accessories________ Nomlxi*t rip* Six* Inches 6 e 10 12 14 15 16 18 30 21 24 1 |l ow MINIMUM CRUSHING STRENGTH tnS./FT. * 2000 2000 2000 2000 2300 2500 2500 2500 2500 2800 25 40 . 2400 2500 . 3500 2500 2800 3000 3000 3500 3500 3800 2400 2800 3000 3000 3000 3300 3500 4000 4500 4500 5000 45 3200 3400 3500 4000 4000 4300 4500 5000 5500 5800 6?00 Class 50 60 70 80 90 4000 4000 4500 5200 5200 5500 5S00 6500 7100 7300 8100 4700 4E00 5500 6400 7000 7400 7500 8500 9500 9700 11000 5400 55CO 7000 7300 8S00 9300 9500 nooo 12000 12500 15000 6700 7400 9000 10000 11000 12000 12400 14000 15000 16000 19000 9000 9300 11000 12200 13500 14 500 15400 IS coo 70000 . - 7*0 Diameter The Inside pipe diaraeter shall not vary from the stated nominal standard diameter more than 1/4 Inch for pipe 21 Inches and smaller In diameter and 5/16 Inch for pipe 24 Inches and larger in diameter* 8.0 Stralghtnoag - The straightness of each length of pipe shall not vary more than 0.C5 inch per foot of length measured In accordance with Section 12 of ASTH Designation: C5C0. 9.0 CHEMICAL REQUIREMENTS Uncocbincd Calcium Hydroxide *1.0 per cent maximum 10.0 STANDARD COUPI-TXG One coupling suitable for the particular slac and class of pipe with vhlch It Is to be used shall be attached to each standard and random length and shipped as a prebelled unit. Other couplings lor use vith Includes shall be shipped loose. 11.0 ROfeBEK. RINGS FOR FLU 11? TRANSMISSION Tvo CG'rubber Tings shall be furnished vlth each coupling. : The rubber rings shall r.cet the require ments of the latest issue of ASTW D1869 and PtiFG Purchasing Specification No. 507. Rubber rings ^ shall be composed of natural rubber, synthetic elastomer, or when specifically requested, an cil resistant compound. Rubber rings arc to be shipped in cartons and properly identified. 12.0 RUBBER KTNOS FOR BUREAU OF RF.C1AMATI0N Tvo Rc,nd Rubber Rings shall be furnished vlth each coupling. The rubber rings shall meet the re quirements of the latest Issue of ASTM D18G9 and V6VC. rurcUasir.g Specification No. 530. P.ubber rings shall be composed of natural rubber, synthetic elastomer, and vhen specifically requested, an oil resistant compound. Rubber rings are to be shipped In cartons and properly Identified. PACPAACD av: trj*} plants supplying Bureau of Reclamation and Fluid-Transmission, It la permissible to prebell the pipe using round rubber rings. The rings that aro shipped loose to the field tnuat bo the correct rings* That Is, round rubber for tho Bureau and CG rings for Fluid-Transmission. aip*ovko av: 0*0 SA.A- -10-0023 (^927) 12/76 CONPIOtNTIAL DOCUMENT - NOT Tb BE DISTRIBUTED TO UNAUTHORIZED PKRSONNCL CTD015440 Page 4 13.0 B.O.D. CONTROL All B.O.D.'s in this specification are called out as minlmims. Costs aro based on a B.O.D. + ,04" over tlie minimum end it is intended that the coats will prevent excessive B.O.D.'s. 14.0 H3J,Wg riels lubricant shall ho furnlahed in it evarc cans in aecordanca vfth tha following tails, rivo (5) gallon palls My bo tUbctlCuted un ipcclol cuiccacr order. Ptpo Site, tnchet 6 6 10 12 14 15 16 18 20 21 24 .Joints Pr 1 Qt. Container All Clottct 46 33 26 16 U 7 6 Joint* For 5 Cot Foil All Clofeos 935 725 543 ' 415 280 270 260 170 155 145 133 15.0 FACKAGIK3 r*ck*fco In occordonca vlLh CT Un4r4 Vocknjlng SpoclMcotion KuaVer 1, WJCIKG 0 Marking ink slinll conform to PSPG Standard PurcheolYig Specification No. 502. Color Code: Use Standard Dlack ink for Areas (A, B, A C) AREA A At the. exact center of the pipe, th* following elinll be stamped. CEKTAINTEED (Siso) FT (Class) AC TYPE IX FLUID TRANSMISSION CTD015441 TECHNICAL SPECIFICATIONS SPECIFICATIONS classification: CertainleedlH A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO! PAOE NO.: CertainTeed Corporation Pipe and Plastics Group 11 supersedes: 15B OMC*imoN: April 30, 1979 A/C Bureau of Reclamation/Fluid Transmission Pipe, Couplings and Accessories OATE OF ISSUE: feb i 5 AW B Identification Harking*: Flr*t line Month, Day, Year, Plant, Shift Example 03087758C Second line - Pipe No. 259 AW C Clat* Pipe: Tested at P5I. (Insert Proof Pressure) Example: For FT 30 pipe cha proof pressure vould be 225 PSI. Coupling At the approximate centkr around the coupling. CERTAINTEED (Sice) FT (Class) AC FLUID TRANSMISSION T T - Indicates Coupling has been hydrostatically tested. Example: CERTAINTEED 6" FT 40 AC T FLUID TRANSMISSION Pre-helled The plant number shall b* stamped In black Ink on tha Coupling B.O.D. and stanped on the pipe O.D. shoulder near to where the coupling Is stamped. Stamp to be 1 Inch minimum. Fully Machined (FM) At the approximate center of the pipe, the following shall appear: CERTAINTEED (Sice) FT (CUss) AC TYPE II FLUID TRANSMISSION Example: CERTAINTEED 6" FT 40 AC TYPE II FLUID TRANSMISSION In addition, the following shall appear: 1st line: 2nd line: Example: FM tosted st psl. Company Coda. FM Tested at 300 pal. 03087758C mcpARro my: 02- APPROVED by: R *D MPO. SALES I.E. J.G.A. OTHERS CTD015442 PI D Page 6 Standard Random 1/2 Standard (KEO) 1/4 Standard (KEO) 1/S Standard (KEO) IS' 7'0" to li'" (6" lncrsasncs) 8*6" J'l" 19.3" (Slisi 6" thru 12" only) Laaftk _12JUT_ +0" -1" 0" -l" +0" -I" +0" -1" io.i" 3/l6R^`/l6 Tip. Si*e( Iiithas Class 30 -------B-- 10 1? lii 15 16 16 20 n ifa CUss >S --T i 10 11 lL 15 16 16 to. n iu CUss IsO -------5-- 8 10 12 111 IS 15 16 20 21 21i CUss IS ----- 5~ 6 10 12 111 15 16 16 20 21 ?li CUss SO ft 6 10 12 ' 111 15 16 16 20 21 ill I.D." Nam. OOy* oo.?a 6.00 10.00 11.00 111. 00 IS. oo 16.00 18.M io.cn il.00 ill .oo 8.80 10.6? 12.?9 15.07 16.11 17.IS 19.28 2l.li!i 22.52 ?s. 76 8.96 11.05 13.15 15-23 16.27 17.31 i?.iiii 21.60 22.68 25.92 6.00 10.00 12.00 lli.QO 1S.OT 16.00 18.00 20.00 il.00 ill. 00 8.80 10.89 12.99 15.07 16.11 17.15 19.28 21.Ui 22.52 2S.76 8.96 11.05 13.15 15-23 16.27 17.31 19.Uli 21.60 22.68 25 92 6.00 8.00 10.00 12.00 u.oo IS. 00 U.oo 18.00 20.00 21.00 ill .00 6.69 6.80 10.89 12.99 15.07 16.11 17.15 19.90 22.12 23.28 26.1i6 6.BS 8.96 11.05 13-1S 1S.23 16.27 17-31 20.06 22.28 23. Ui 26.61i ' 6.00 8.00 10.00 12.00 lil. 00 15.00 16.00 18.00 20.00 21.00 21l.oo 6.69 8.80 11.21i 13.lili 15.50 16.68 17.7li 19.90 ?2.1? 23.28 26.18 6.85 8.96 ll.liO 13.60 15.66 16.81, 17.90 20.06 22.20 23.U, 26.66 6.00 8.00 10.CO 12.00 U.oo 15.00 16.00 18.00 20.00 21.00 21l.co 6.91 9.11 11.21. 13.lii. 15.50 16.68 17.71. 19.90 ??.1? 23.28 26.1.6 7.07 9.?7 11.1,0 13-60 15.66 1/..BI, 17.90 20.06 22.28 23- W, 26.6li B.a 6" through l/" *.0? 18" through ?IT ;.0) C* t0.06" P. 10.06" oc - 20 X" is.06* 2.40 2.40 2.90 2.25 3.25 3.25 3.75 1.75 3.73 3.75 2.40 2.40 2.90 3.25 3.23 3.23 3.75 3.75 3.75 3.75 2.40 2.40 2.40 2.90 3.25 3.2$ 3.25 3.75 3.75 3.73 3.75 7S.75 1.00 1.00 1.00 1.00 1.00 1.00 1.00. . 1.00 .75 .75 1.00. 1.00 1.00 1.0c 1.00 1.00 1.00 1.00 .7S TS .75 1.00 1,00 1.00 1.00 1.00 1.00 1.00 1.00 16 16 16 18 16 IS 20 20 20 20 16 16 16 16 16 18 20 20 20 20 16 16 16 16 18 IS 18 20 20 20 20 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.30 1.50 I.SO 1.30 1.50 1.50 1.50 1.30 1.30 1.30 l.SO 1.30 1.30 1.50 1.30 1.30 1.30 1.30 1.50 1.50 1.50 1.50 2.40 2.40 2.40 2.90 3.25 3.25 3.25 3.75 3.75 3.75 3.75 .75 .75 .75 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 16 1.50 16 1.30 16 1.30 16 1.50 18 1.30 16 1,30 16 1.50 20 1.50 20 1.30 20 l.SO 20 1.50 2.40 2.40 2.40 2.90 3.25 3.25 3.25 3.75 3.75 3.75 3.73 .75 .75 .7S 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 <16 16 16 16 IS 18 18 20 20 20 20 l.SO 1.30 1.50 1.50 1.50 1,50 1.50 l.SO 1.50 1,50 1.50 *** 4,1. C, 2 C" thru 12" - -.08" K tl.ro 18" - ..12" JO" tl.ru 26" - -.14" B.O.D." HAP. 3.12 11.14 13.29 15.3a 16.66 17.58 19.60 11.76 22.66 26.06 tt a** .400 .445 .495 .335 .555 .375 .640 .720 .760 .680 9.26 11.16 13.27 15.66 16.62 17.58 19-60 21.67 22.91 26.19 7.06 9.26 11.30 13.36 15.66 16.72 17.71 20.21 22.63 23.59 26.82 .400 .445 .493 .533 .333 .375 .640 .720 .760 .880 345 .400 .445 .495 .335 .555 .575 .950 1.060 1.140 1.240 ***2 .460 .315 .375 .615 .635 .655 .710 .800 .040 .HO .480 .313 .375 .615 .633 .633 .710 .800 040 .960 .425 .480 .523 .573 .613 .635 .633 1.030 1.140 1.220 1.320 7.06 ' 936 11.69 15.70 15.76 17.05 16.07 20.21 12.63 . 23.71 16.97 7-18 9-38 11.51 13.87 15.95 17.15 18.11 10.66 1171 13.86 17.15 .545 .400 .620 .720 .750 .840 .870 .950 1.060 1.140 1.240 . .655 .333 .620 .720 .no .840 .670 .950 1.060 1.140 1.140 .425 .480 .700 .600 850 .920 .950 1.050 1.140 1.220 1.320 .515 .833 700 .800 .830 .820 .930 1.030 1.140 1.220 1.320 CTD015443 TECHNICAL SPECIFICATIONS CertairileedEI SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification T.C.O. NKF. NO. SPECIFICATION NO: PAOE NO.: CertainTeed Corporation Pipe and Plastics Group n SUPERSEDES: 15B April 30, 1979 DESCRIPTION: A/C Bureau of Reclamatlon/Fluld Transmission Pipe, Couplings and Accessories 7 DATE OF ISSUE: FEB i 198? Ctoi, <0 6 10 12 lb 1$ It to n - tb to 6 .6 10 12 lit IS IS u to a a ffia; *. Q < 10 V lb 15 16 16 20 21 2b CU 90 6 e 10 12 lb 15 16 18 20 I.0. 1* .A $.80 7.80 10.03 12.00 lb .00 IS .00 16.00 18.00 20.00 21.00 2b.OO 6.n .ii 11.66 11.72 16.22 17.28 18. b6 20.50 22.3J 23.75 27.b2 $.80 7.ao 10.00 12.00 14.00 tj.00 14.00 18.00 20.00 21.00 2<i.OO 6.71 7.11 11.66 11.92 16.22 17.28 18.b6 20.7b 21.28 2b. 38 27.76 $.70 7.60 r.6o n.Ui 1J.60 1$.00 1$.$0 18.03 20.00 21.00 2b.00 6.91 7.11 11.66 13.92 16.22 17.97 18.16 20.7b 23.28 2b .30 27.76 $.70 7.60 7.60 11.bb 11.60 lb.bb l$.$o 18.00 20.00 6.71 9.11 11.66 13 92 16.22 17.79 18.b6 22.18 2b.66 OOj* c* >* 20.06* -O-OS* cc 8 2 7.07 7.27 11.82 lb .08 16.36 l?.bb 18.62 20.66 22.97 2b. 12 27 .$8 2.60 5.25 3.25 3.25 3.75 3.25 3.75 3.7$ .75 .75 ' .7$ 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 14 16 16 16 18 18 . 18 20 20 20 20 7.07 9.27 11.82 lb.oe 16.38 17.bb 18.62 21.10 23 .bb 2b. Sb 28.12 7.07 9.27 11.62 lb .08 16.38 18.15 18.62 21.10 23.bb 2b .SU 28.12 2.40 2.*0 3.40 2.90 3.25 3.25 3.25 1.7$ 1.71 3.71 3.1! 2.40 3.35 3.75 3.75 3.75 3.73 .75 .75 7S 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .7S .75 7S 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 16 16 16 16 18 18 18 20 20 20 20 16 16 16 16 18 18 18 20 20 20 20 7.07 9.27 11.82 lb. 08 16.33 18.15 18.62 22.3b 2b. 82 1.40 2.40 2.40 7.70 3.25 1.21 3.25 1.7! 1.21 .75 .75 .75 1.00 1.00 1.00 1.00 1.00 1.00 16 16 16 16 18 18 18 20 20 . * -0.06* 1.30 1.30 1.30 1.30 1.50 1.50 1.30 1.50 1.30 1.50 1.30 l.to 1.30 1.30 1.50 1.50 1.50 1.30 1.50 1.50 1.30 1.30 1.30 1.10 1.50 1.30 1.50 1.50 1.30 1.50 1.50 1.50 3.30 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1,50 And i3.0.9 6" through id" * .02". 16* through ?l<" ***t. 6 4 6" thru 12" - -.08" H" thru IB" - -.12" 20" thru 26" - -.16" B.O.D." Min. 7.12' 9.31 11.51 14.17 16.50 17-61 18.74 20.94 23-26 24.44 27-96 9.J2 II.9) 14.35 16.70 17-93 19-09 21.48 23.7$ 25.10 28.60 .555 .655 830 960 1.610 1.140 1.230 1.250 1.415 1.460 1.710 .535 .655 830 960 1.310 1.420 1.230 1.470 . 1.640 1.690 1.980 7.16 7.46 11.91 14.17 16.50 16.43 18.95 21.92 24.36 25.69 29.22 7.35 9.62 12.34 14.52 16.92 18.26 19,52 22.60 25.16 .60S .755 1.030 1.240 1.310 1.495 1.480 1.470 1.640 1.690 1.990 .605 .755 1.030 1.240 1.310 1.775 1.460 2.090 2.330 *Se .693 735 910 1.040 1.190 1.220 1.910 1.330 1.699 1.360 1.790 .699 .739 .910 1.040 1.990 1.500 1.310 1.550 1.720 1.770 2.060 665 635 1.110 1.320 1.390 1.575 1.560 1.550 1.720 1.770 2.060 .685 .835 1.110 1.320 1.390 1.855 1.560 2.170 2.410 PREPARED EY: APPPOVEO by: 02-10-0023 (P927) 12/76 CONF R t D | MFO. At k SALES ue.A I.E. CTD015444 Page 8 Coupling Stic, Inches A" * Class 30 9.54 10 11.63 12 13.73 14 15.95 15 16.99 16 18.03 16 20.16 20 22.32 21 23.40 24 26.64 Class 35 8 9.54 10 11.63 12 13.73 14 15.95 15 16.99 16 18.03 18 20.16 20 22.32 21 23.40 24 26.64 Class 40 6 7.43 8 9.54 10 11.63 12 13.73 14 15.95 15 16.99 16 18.03 18 20.78 20 23.00 21 24.16 24 27.36 Class 45 7.43 9.54 10 11.98 12 14.18 14 16.38 IS 17.56 16 18.62 18 20.78 20 23.00 21 24.16 24 27.36 AS i 8 10 12 14 15 16 18 20 21 24 50 7.65 9.85 11.98 14.1?. 16.;.' 17.56 18.62 20.78 23.00 24.16 27.36 9.09 11.18 13.28 15.39 16.43 17.47 19.60 21.76 22.84 26.03 9.09 11.18 13.28 15.39 16.43 17.47 19.60 21.76 22.84 26.08 6.98 9.09 11.18 13.28 15.39 16.43 17.47 20.22 22.44 23.60 26.80 6.98 9.09 11.53 13.73 15.82 17.00 18.06 20.22 22.44 23.60 26.80 7,20 9.40 11.53 13.73 15.82 17.00 IB.06 20.22 22.44 23.60 26.80 2" * 8.92 11.01 13.11 15.20 16.24 17.28 19.41 21.57 22.65 25.89 8.92 11.01 13.11 15.20 16.24 17.28 19.41 21.57 22.65 25.89 6.81 8.92 11.01 13.11 15.20 16.24 17.28 20.03 22.25 23.41 26.61 6.81 8.92 11.36 13.56 15.63 16.81 17.67 20.03 22.25 23.41 26.61 7.03 9.23 11.36 13.56 15.63 16.81 17.87 20.03 22.25 23.41 26.61 +0.03" -0.01" +0.00" -0.04" +0.02" -0.00 Min. +0.032" -0.000" .92 .92 .92 1.00 1.00 1.00 i.00 1.00 1.00 1.00 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 .92 .92 .92 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 1.00 .92 .92 .92 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 1.00 .92 .92 .92 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 .92 .92 .92 .92 1.00 1.00 1.00 . 1.00 1.00 1.00 1.00 .42 .42 .42 .42 .42 ,42 .42 .42 .42 .42 .42 .18 .18 .18 .25 .25 .25 .25 .25 .25 .25 .18 .18 .18 .25 .25 .25 .25 .25 .25 .25 .18 .18 .18 .18 .25 .25 .25 .25 25 .25 .25 i 18 .18 .18 .18 .25 .25 .25 .25 .25 .25 .25 .18 .18 .18 .18 .25 .25 .25 .25 .25 .25 .25 .76 .76 .76 .63 .83 .83 .83 .83 .83 .83 .76 .76 .76 .83 .83 .83 .83 .83 .83 .83 .76 .76 .76 .76 .83 .83 .83 .83 .83 .83 .83 .76 .76 .76 .76 .83 .83 .83 . B3 .83 .83 .83 .76 .76 .76 .76 .83 .83 .83 .83 .83 .83 .83 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 * Tolerance A, Bj and 6" through 16" +.025". 10" through 24" +.040". +0.00" -0.06" +0.06 3.50 3.50 4.50 5.20 5.20 5.20 6.20 6.20 6.20 6.20 3.50 3.50 4.50 5.20 5.20 5.20 6.20 6.20 6.20 6.20 3.40 3.50 3.50 4.50 5.20 5.20 5.20 6.20 6.20 6.20 6.20 3.40 3.50 3.50 4.50 5.20 3.20 5.20 6.20 6.20 6.20 6.20 3.50 3.50 3.50 4.50 5.20 5.20 5.20 6.20 6.20 6.20 6.20 7.00 7.00 8.00 9.00 9.00 9.00 10.00 10.00 10.00 10.00 7.00 7.00 8.00 9.00 9.00 9.00 10.00 10.00 10.00 10.00 7.00 7.00 7.00 8.00 9.00 9.00 9.00 10.00 10.00 10.00 10.00 7.00 7.00 7.00 8.00 9.00 9.00 9.00 10.00 10.00 10.00 10.00 7.00 7.00 7.00 8.00 9.00 9.00 9.00 10.00 10.00 10.00 10.00 Min. 10.50 12.50 14.70 17.60 18.40 19.31 21.53 23.83 25.11 28.43 10.50 12.75 15.00 17.60 18.40 19.80 21.77 24.01 23.24 28.65 8.18 10.50 12.75 15.00 17.60 18.67 19.80 22.82 25.24 26.79 29.98 8.18 10.67 13.30 15.55 16.20 19.51 20.42 23.20 25.66 26.93 30.52 8.40 10.90 13.30 15.76 16.49 19.82 20.69 23.30 25.78 27.07 30.66 CTD015445 TECHNICAL SPECIFICATIONS CertairileedH CertalnTeed Corporation Pipe and Plastics Group oMcmmoN: SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification 'ipiciFICATION NO~ PAOS NO.: 15B SUPERSEDES: April 30, 1979 DATE OF ISSUE: FEB 1 mi A/C Bureau of Reclamation/Fluid Transmission Pipe, Coup!i ngs and Accessories Coupling A" Slaa. In * Clata 60 --r~ 7.65 8 9.85 10 12.40 11 14.66 14 17.10 IS 18.16 16 19.34 18 21.38 20 23.71 21 24.84 24 28.30 'Cists 70 --r~ 7:65 8 9.65 10 12.40 12 14.66 16 17.10 IS 18.16 16 19.34 18 21.82 20 24.16 21 25.26 24 28.84 7.20 9.40 11.95 14.21 16.54 17.60 18.78 20.62 23.15 24.28 27.74 7.20 9.40 11.95 14.21 16.54 17.60 18.78 21.26 23.60 24.70 28.28 Bj" 7.03 9.23 11.78 14.04 16.35 17.41 18.59 20.63 22.96 24.09 27.55 7.03 9.23 11.78 14.04 16.35 17.41 18.59 21.07 23.41 24.51 28.09 0" +0.03" -0.01" j" +0.00" -0.04' Jl" +0.02" -0.00" .92 .92 .92 .92 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 .42 .18 .18 .18 .18 .25 .25 .25 .25 .25 .25 .25 .92 .42 .18 .92 .42 .18 .92 .42 .18 .92 .42 .18 1.00 .42 .25 1.00 .42 .25 1.00 .42 .25 1.00 .42 .25 1.00 .42 .25 1.00 .42 .25 1.00 .42 .25 Claaa 80 --r 7.65 8 9.85 ` 10 12.40 12 14.66 14 17.10 IS 18.87 16 19.34 18 21.82 20 24.16 21 25.26 24 28.84 Claaa 90 ----- 5" 7.65 8 9.85 10 12.40 12 14.66 14 17.10 IS 18.87 16 19.34 18 23.06 20 25.54 7.20 9.40 11.95 14.21 16.54 18.31 18.78 21.26 23.60 24.70 28.28 7.20 9.40 11.95 14.21 16.54 18.31 18.78 22.50 24.98 7.03 9.23 11.78 14.04 16.35 18.12 18.59 21.07 23.41 24.51 28.09 7.03 9.23 11.78 14.04 16.35 18.12 18.59 22.31 24.79 .92 .92 .92 .92 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .92 .92 .92 .92 1.00 1.00 1.00 1.00 1.00 .42 .18 .42 .18 .42 18 .42 .18 .42 .25 .42 .25 .42 .25 .42 .25 .42 .25 .42 .25 .42 .25 .42 .18 .42 .18 .42 .18 .42 .18 .42 ' .25 .42 .25 .42 .25 .42 .25 .42 .25 * TolarMie A, B^ and Bj 6" through 16" +.025". 18" through 24" +.040". 7" Hln. B" +0.032" -0.000" M" +0.00" L" -0.06" +0.06 ` B.O.D." Min. .76 .093 3.50 7.00 8.76 .76 .093 3.50 7.00 11.32 .76 .093 3.50 7.00 14.36 .76 .093 4.50 8.00 17.00 .83 .093 5.20 9.00 19.80 .83 .093 5.20 9.00 21.02 .83 .093 5.20 9.00 22.28 .83 .093 6.20 10.00 24.79 .83 .093 6.20 10.00 27.49 .83 .093 6.20 10.00 28.79 .83 .093 6.20 10.00 32.47 .76 .093 3.50 7.00 8.76 .76 .093 3.50 7.00 11.32 .76 .093 3.50 7.00 14.36 .76 .093 4.50 8.00 17.13 .83 .093 5.20 9.00 20.26 .83 .093 5.20 9.00 21.52 .83 .093 5.20 9.00 22.54 .83 .093 6.20 10.00 26.00 .83 .093 6.20 10.00 28.78 .83 .093 6.20 10.00 30.03 .83 .093 6.20 10.00 34.34 .76 .093 3.50 7.00 9.35 .76 .093 3.50 7.00 12.00 .76 .093 3.50 7.00 15.15 .76 .093 4.50 8.00 17.90 .83 .093 5.20 9.00 20.50 .83 .093 5.20 9.00 22.46 .83 .093 5.20 9.00 23.20 .83 .093 6.20 10.00 26.68 .83 .093 6.20 10.00 29.52 .83 .093 6.20 10.00 30.81 .83 .093 6.20 10.00 35.22 .76 .093 3.50 7.00 9.35 .76 .093 3.50 7.00 12.00 .76 .093 3.50 7.00 15.15 .76 .093 4.50 8.00 17.90 .83 .093 5.20 9.00 21.06 .83 .093 5.20 9.00 23.01 .83 .093 5.20 9.00 23.47 .83 .093 6.20 10.00 28.29 .83 .093 6.20 10.00 31.41 PNKPARKD Brs 02-10-0023 (P927) APPROVED SY: ft O jL12/76 "cONFIIDI[NTIAL~DOCUMENT^-NOT^iTO" MFD. k r> m m MA- I.E. OTHERS Page 10 rw.tr wcsiksp rot (no hM sit* . r* oc io.o4* i 7 6" throuch 32" lb* through 16* 16* through 2b" 1.00 1.00 1.00 u 18 22 Pioc Sice Std . Half +01 -l" St4d0.'..Q_urarter Std+ . Eighth 0.5" * thru 12" U" thru 16" It" thru 24" 6* 6" 6' 6" 6* 6" 3 3. yj". 3 J" 1.9...3" --- Pipa SI to, Inc ho i CUss 10 8 10 1? lit IS 14 It 20 a 2b 1.0." Non. 8.00 9.90 12.00 lit .00 lit .80 is.es 18.00 20.00 21.00 2it.oo O.D." * 8.80 30.89 12.99 1S.07 16.11 17.1S 19.28 21 .bb 22.52 25.76 Clots 3$ e 10 12 lit 1$ 18 16 y> ii 2it 7.80 9.90 I1.6S 13.75 It. 80 15.50 17.35 19.65 20.70 2>l.00 e.eo 10.89 12.99 1S.07 16.11 17.15 19.28 21.lilt 22.52 25.76 Class bO 6 S.90 6/9 8 7.80 8.60 10 9.SS 10.89 12 11.70 12.99 lit 13.7$ 15.07 1$ llt.ltS 16.11 16 IS. 50 17. IS 16 18.00 19.90 20 20.00 22.12 21 21.00 23.28 2lt 2Jt.OO 2o.lt8 * Tolerance Center O.D. 6* through 16* iO.O?*" 16* through 2It" 0.035" End O.D. 6" through 36" io.CPO" 16* through 2b" +0.030M Keaeund 6" in on both enis. Pipa Siu. Inches Class b5 6 6 10 12 lb IS 16 18 20 a 2It Class $0 6 8 10 12 1$ 15 14 id 20 a 2 It Claes 60 6 B 10 12 lb IS 16 18 20 21 ` 2It l.D." Non. 5.80 7.55 9.90 12.00 14.00 15.00 16.00 17.35 19.65 21.00 23.35 5.95 $.00 9.90 li.u 13.75 15.00 15.85 17.35 19.65 20.70 23.60 5.80 7.80 9.90 12.00 it .00 15.00 16.00 17.35 19-65 20.70 23.60 O.D.* 6.69 8.80 11.21. 13-ltlt 15-50 16.68 17.71. 19.90 22.12 23.28 26.ltS 6.91 9.11 11. lit 13.Ut 15.50 16.68 17.7b 19.90 22.12 23.28 26.bS 6.91 9.11 11.66 13.92 16.22 17.28 18.116 20.50 22.03 23-96 27.1.2 Pipe flit*, Inch** Claae 70 6 a 10 12 lb IS 16 18 20 a 2b CUia 80 6 8 10 12 lb IS 16 16 20 a 2b Class 90 6 8 10 17 lb IS 16 18 20 X.D.* Non. 5.66 7.80 9.90 12.00 16.00 is.00 15.8s 17.15 19.00 20.70 2b.M 5.70 T.SS 9.SS 11.6$ 13.bS IS .00 IS .so 17.35 19.00 20.00 2J.IK) S.30 7.bS 9.SS 11.55 13.20 llt.LS 15.30 18.00 20.00 P.0," 6.91 9.11 11.66 13.92 16.7? 17.28 18. b6 20.9b 21.28 2b.36 27.96 4.91 9.11 JT.44 13.92 16.22 17.99 lfl.b6 20.9b 23.26 tli. 38 27.96 4.91 9.11 11.66 13.92 16.22 17.99 18. b6 22.18 2b.66 At Plant 57 the foil owing tolerance ia effective to allov for gang tooling. QOI25- ToUr*nC* ** through 14" Center O.D. io.02S" 18" through ?b" Center O.D. 10.03S" Bid O.D. 0.030" la atMltion, thor. cannot bo a atop (roator than 0.02$' (0.012$* on a aldo). CTD015447 TECHNICAL SPECIFICATIONS SPECIFICATIONS CLASSIFICATION: CertairileedlH A/C Standard Product Specification T.C-O. REF. NO. SPECIFICATION NO: PAGE NO.: CertainTeed Corporation Pipe and Plastics Group 9 supersedes: July 25, 1977 15B 11 DATE OF ISSUE: JAN 1 G 1978 description: A/C Bureau of Reclamation/Fluid Transmission Pipe, Couplings and Accessories pipe inmor (pap 13) for dimensions tio4 shown refer to Full? Machined Pipe. Martinet HIGHER CLASS END CT - PAD 13 (Site) FT (Class) AC FLUID TRANSMISSION AGRI-PEP.M Dimensions LOWER CLASS END CT-FAD 13 (Site) FT (Class) AC FLUID TRANSMISSION AGRI-PERM Pip* Site, Inches AC Class to AC Class I.D.* Kora, O.D.i" 10.02" O.D.j" 10.02" V. 0.0" -0.S" * 0.0" -o.S" I* 6 tS to So s.8o 6.69 6.91 iS.o 8,0 3.06 6 IS to So 7.SS 8.60 9.11 1S.0 8.0 3.06 10 liO to ItS J.SS 10.69 11.2i 1S.0 6.0 3.06 10 So to 60 9.90 11.28 11.66 1S.0 8.0 3.06 12 to to ts 11.70 12.99 13.ti 1S.0 6.0 3.56 12 SO to 60 11.65 13.it 13.92 15.0 8.0 3.56 Hi to to ts 13.7S 1S.07 15.S0 19.S ll.S i.OS Hi So to 60 13.90 IS.So 16.22 . 19.S ll.S 8.08 IS to to 85 IS.00 16.11 16.68 lv.s ll.S 8.03 IS So to 60 1S.00 16.66 17.28 19.5 ll.S 8.03 IS 16 70 to to to 80 ts IS.00 17.28 15.SO 17.1S 17.99 17.7t 19.5 19.S ll.S 8.08 ll.S i.oa 16 So to 60 is.es 17.7t lfl.t6 19.S ll.S 8.08 16 3S to to 17.35 19.28 19.90 19.S ll.S 8.58 18 SO to 60 17.35 19.90 20.50 19.S ll.S 1-58 16 16 6600 to to 7so0 17.35 20.50 17.35 20.9i 20.9t 22.18 19.s 19.5 ll.S ll.S i.se 8.S3 20 3S to to 1S.6S 21 .it 22.12 19.S 11.5 t.S8 ?0 20 ?0 SO to 60 60 to 70 60 to 90 19.6S 19.65 19.00 22.12 22.83 23.28 22.83 23.28 28.66 19.S 19.5 19.5 ll.S 8.58 ll.S i.53 ll.S 8.58 21 35 to to 20.70 22.52 23.23 19.S ll.S 8.56 21 50 to 60 20.70 23.28 23.96 19.S ll.S t.se 21 60 to 70 20.70 23.96 2t.38 19. S ll.S t.S8 2!i 221Il| JS to to SO to 60 ' 60 to 70 2t.00 23.1|0 23.to 25.76 26.80 27.i2 26.88 27.82 27.96 19.5 19.S 19.S ll.S i.S8 ll.S ll.S t8..s5a6 Motet Distance X Is Insertion depth Into coupling to insure positive separation of pipe ends. Nark pointed around th* circumference of th PAD irith standard black Ink, and shall be 1/lj" wide, Point r to be In line with outside fees of coupling. PREPARED BY: APPROVED BY: 'yy\^ -10-0023 (P927) 12/76 CONFIDENTIAL DOCUMENT - NOT TO BE DfISTRIBUTEOD TO UNAAUTHORIZED PERSONNEL CTD015448 flPS ADAPTOR (PAD X?) Page 12 forking: Cl - PAD 15 (Site) FT (CLeai) AC FLUID TRAKSKISSlOff Dimensions Pit* Sire. Inches AC Class X" 6,8,10 All 3.06 12 lli, IS,16 All 3.56 All It .08 18,20,21,2b All It.58 Kote$ 1. ftsfer to Fully Kachlned Pipe, age 10, for dimensions not shown. 2. Distance X is Insertion depth into coupling to insure positive separation of pipe ends. Hark will be painted around the circumference of the PAD with standard black ink and shall be l/li* wide. Point P to be in line with outside face of coupling. PIPE ADAPTOR (PAD 16) forkingi CT - PAD 16 (Site) FT (CUta) AC FLUID TRANSMISSION *----------------------- fi5*OW.... L50%)6 1I 00, oo2 ` 4* . * .-A4 * f ID -----q--------f- 1 -P V ^CC Dimensions Notei 1. Available in all sites and classes. 2. Rafsr to Standard Pipe, Pages 6 and 7, for all diwsnslons not shorn except for length. TECHNICAL SPECIFICATIONS CertainTeed ESI SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification Y.C.O. REF. NO. SPECIFICATION NO: PAGE NO. : CertainTeed Corporation Pipe and Plastics Group description: A/C Bureau of Pipe, n supersedes: April 30, 1979 15B Reclamation/Fluid Transmission Couplings and Accessories OATS OF ISSUE: FEB 1 13 1982 ripe Adaptor (TAP 17) A/C to Mechanical Joint and/or Poured Bell ":. 0"10, x5F XV.. V ' / *t : , -sf i t-V stripe . ;-F.v `a- ------------ x-- ID &LLM -/ *- -.50j0S* 002 C_...I....M. ...c...c...h....tmritleC*'!i) Joint hr I Yxirac!~HeJi Tor dimensions not shown, refor to roily Hichined ripe. Karklngi ac side CT - PAD 17 (Site) FT (Class) AC FLUID TRANSMISSION Mminelons KJ/PB SIDE CT-PAD 17 FLUID TRANSMISSION Plpo Si?#, InetiM e e 10 10 ID 12 1* IP 111 . Hi 111 16 16 16 16 ' 16 10 16 16 to 80 to 20 to til til til tti . AC C199C3 . lo,6S )o to 65 So to . JO to to IS,So 60 to JO JO to tiO IS,So 60 to JO jo to iio I.S.S0 Co to $0 JO to lo 65,50 60 to JO JO.JS 60 to So Co 70,60 JO JO.JS lo to So 60 10,60 JO lo to So 60 70,60 I.D," Km. S.6S 7.SS 7.SS J.SS J.SS J.SS 11.1s 11.65 11 .IS lj.60 11.60 11.60 IS.So iiss..SSOo 17.JS 17.JS n.3S 17. JS 17.35 1J.00 19.00 i?.oo 19.00 i?.oo tj.w tl.oo 8J.00 PJ.00 O.D.j* JO.O?** 6.69 6.60 9.31 10.6J 11.21 11.66 It.9? 13.66 13. Jt 1S.07 15.S0 16.22 17.15 17.71 16.66 19.28 19.90 20.SO 20.16 22.10 21.1.6 22.3 2 22.63 t). 28 26.66 2S.76 26.68 27.62 27.96 O.D. 6.91 . j.o; 9.0s 11.10 11.10 11.10 1J.20 13.20 13.?0 1S-30 IS.30 lS-30 17.10 17.1.0 17.60 19-50 19.So 19-So 19.SO 19.So 21.60 21.60 21.60 21.60 21.60 2S.S0 25.60 25.60 2$.60- Ll" yj-.so; 1S.00 1S.0O lS.OO iS.co iS.co lS.oo 15.00 iS.co 1S.00 19.So 19.50 19-So 19.50 19.50 19.S0 19. So 19.S0 19.50 19.50 19.50 19. SO 19.50 19.50 19.SO 19-SO 19.SO 19.50 19.50 19.50 It* 6.00 6.00 6.CO 6.00 6.CO 6.00 6.00 e.co 8.CO 11.S0 ll.So ii.So 11.S0 ll.So ll.So 11.50 31.50 ll.So 11.50 11.50 ll.So ll.So ll.So ll.So ll.So 11.50 11.50 11.ST 31.50 I* 3-OS 3.06 3.0o 3.06 3.03 3.06 3.S6 3.56 3.56 6.03 6.03 6.03 6.03 6.0S 6.06 6.S3 6.58 6.53 6.53 6.53 6.56 6.53 6.53 6.58 6.53 6.53 1.58 6.53 6.58 Has. .60 .60 .60 .75 .75 .75 .75 .75 .75 1.05 1.05 1.05 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.20 1.40 1.40 1.40 1.40 KoUi 1. BltUnc* X Is lneertion depth Into coupling to Insure positive separation of pipe ends. Hark will be pointed around the clrcunfarenee of the W.D vlth standard black Ink, and shall be 1/6* uids. Point T to be In line vlth outside face of coupllnf. Tolerance on It* through Hi* tO.Ol" v? a APPROVED BY: P AO m J4.AJ- 02- 10-0023 (P927) 1^/76 confidential oocument SSt TO BC OISTRIBUTBO TO UNAUTHORIZED PERSONNEL CTD015450 urt >mnoR (r*p ib) loner CTjU* fetd Pg 14 Higher Clin tad 195'* O'-1 00/ CD? T /D BOD j*tc^L rp:pr-=3>=004 QDj Refer to Standard Pipe, Pc^aj 6 and 7 for dlnonslona not ahovn. Kariditc: Cl - FAD id (sue) pr (dm) ac n.010 TRANSMISSION lover Clast 2nd Plmonslorn Pipj Sl*o, Inches AC Class To AC Clnas I.D.* Van. O.D^" OtBij" O.D.i" 3 & 15 to $0 6.00 6.6s 6.8S 6.91 8 US to 50 8.00 8.80 8.96 9.11 10 IiO to US 10.00 10. C9 11.05 11.26 10 50 to 6o 10.00 la.aJi 11.Lo 11.66 1? to to t5 12.00 12. ss 13.IS 13.66 12 SO tc 60 12.00 lJ.Ui 13.60 13.92 Hi to to US 13.60 1S.07 35.23 15-SO Hi 5o to 60 Hi .00 1S.S0 IS.66 16.22 is tiO to IS IS.oo 16.11 16.27 . 16.60 IS SO to 60 15.00 16.68 I6.e6 17.28 IS 70 to S') 15>00 17.28 17.66 17.99 16 to to Ii5 IS-50 17.1S 17.31 17.76 16 So to 60 16.00 17.76 17.90 18.66 16 IS to lio ic. oo IS. 28 19.66 19.90 ia So to 60 18.00 19.90 20.06 20. SO 18 60 to 70 18.00 20. SO 20.66 20.96 18 80 to SO 18.00 20.96 21.10 22.18 20 15 to IiO 20.00 21.66 21.60 22.12 20 So to 60 20.00 22.12 22.28 22.83 20 60 to 70 20.60 22.83 22.99 23.20 20 80 to SO 20.00 23.28 23.66 26.66 21 35 to to 21.00 22.52 22.68 23-28 n So to 6c 21.00 23.28 23.66 2J. 96 21 60 to TO 21.00 23.96 26.12 26.38 2ti 35 to to 21|.00 2S.76 25.92 26.66 2ll SO to 60 26.00 26.68 26.66 27.62 2l| 60 to 70 21i.00 27.62 27.S3 27.96 CT - PAD 18 [Sill) IT (Cleat) AC PLVin TBANSMlSSIOM Richer CUaa End O.D.jj" a 7.07 9.27 11.60 11.82 13.60 16.08 1S.66 16.38 16.86 17.66 10 .IS 17.SO 18.62 20.06 20.66 21.10 22.36 22.28 22.99 23.66 26.62 23.66 26.12 26. ft 26.66 27.58 28.12 C" 10.06* 2.30 2,30 2.30 2.30 2.80 2.80 3.2S 3.2S 3.2S 3.2S 3.25 3.25 3.25 3.75 3.7S 3.7S 3.7S 3.75 3.7S 3.7S 3.7S 3.7S 3.75 3.7S 3.7S 3.7S 3.75 B.O.D." Kin. 7.16 9.38 11.66 11. os 13.70 16.11 1S.7S 16.61 17.05 17.81 16.63 17.99 18.65 20.16 20.96 21.68 22.60 22.38 23.26 23.60 25.16 23.72 26.66 25.10 26.82 27.96 28.60 * Tolerance on O.D.}, O.D.?, O.D..3, 0.D,j| 6" through l6M 40.02 M 18* through 2ti" 40.03 Pirn: adaptor (pad ioi CT to VALVE Rofor to SUndnrd Pipe, Pagos d and 7* for machined dimonolons not ehown. Horklngi ac m VAT.VC TIIO CT - PAD 19 (st) rr <ciai) ac FLUID TRAKSMISS ION iValva In* 1 (Cl...) CTD015451 TECHNICAL SPECIFICATIONS CertairileedEI SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: PAGE NO.: CertainTeed Corporation Pipe and Plastics Group 9 supersedes: 15B 15 DATE OF ISSUE: January 17, 1978 JflN 1 6 1978 description: A/C Bureau of Reclamation/Fluid Transmission Pipe, Couplings and Accessories PIPE ADAPTCn (PAD 19) poryatje TSswramran Dimensions Pipe Sira, Inches AC Classes I.Da" Wore. O.D.j" *0.02" 0,D.?n 10.02" A I*" iO.SO" X" To Claes 100 6 IiO.IiS 5.65 ------T59------ 6.91 i5.oo 8.00 3.06 e 30 to li? 7.55 6.80 9.11 lS.oo 8.00 3.06 10 30 to 1*0 9- 55 10.89 11.26 IS.oo 8.00 3.06 10 60 to 90 9.55 11.66 11.26 lS.oo 8.00 3.06 12 30 to tiO 11.65 12.99 13.66 lS.oo 8.00 3.S6 ip 60 to 90 11.65 13.92 13.66 lS.oo 8.00 3.56 lb 65,50 13.60 15.50 15.07 19.50 11.50 6.08 Hi 60 to 90 13.60 16.22 15.07 19.50 11.50 6.08 16 65,50 IS.So 3 7.76 17.IS i9.5o n.So 6.08 16 60 to 90 15.50 18.66 17.15 19.50 u.So 6.08 16 30,35 17.35 19.28 19.90 19-So 11.50 6.58 18 6o 17.35 20.50 19.90 19.50 11.50 6.58 18 70,0O 17.35 20.96 19.90 19.50 11.50 6.58 18 90 17.35 22.18 19.90 19.50 11.50 6.58 20 30,35 19.00 21.66 22.12 19.50 u.So 6.SB 20 60 19.00 22.63 22.12 19.50 U.5o 6.S8 20 70,80 19.00 23.28 22.12 19.50 u. So 6.58 20 90 19.00 26.66 22.12 19.50 li.So 6.58 2ll 30,35 23.00 25.76 26.68 19.50 n.5o 6.53 26 60 23.00 27.62 26.68 19.50 ll.So 6.58 21* 70, eo 23.00 27.96 26.68 19.50 11.50 6.58 To Class ISO and 200 6 loM 5.6S 6.69 6.91 lS.oo 8.00 3.06 8 30 to 65 7.55 8.60 9.11 lS.oo 6.oo 3.06 10 30 to IjO 9.SS 10.89 11.66 lS.oo 8.00 3.06 10 65,50 9.55 11.26 11.66 lS.oo 8.00 3.06 12 30 to 6o 11.6S 12.99 13.92 lS.oo 8.00 3.S6 12 65,SO n.65 13.66 13.92 lS.oo 8.00 3.56 lb 65,50 13.60 15.50 16.22 19.50 11. SO 6.08 lb 60 to 90 13.60 16.22 16.22 19.50 11.50 6.08 16 30 to 6o 15.50 17.15 10.66 19.50 u.So 6.08 16 65,50 15.50 37.76 18.66 19.50 ll.So 6.08 16 16 18 18 20 20 20 20 2il 21* 21* Hot* I 30,35 6o to So 6o 90 30,35 1|0 to $0 6o 90 30,35 2j0 to J>0 60 17.35 17.35 17.35 17.35 19.00 19.00 19.00 19.00 23.00 23.00 23.00 To Class 150 19.2b 19.90 20.50 22.18 21.66 22.12 22.83 26.66 25.76 26.68 27.62 20.96 20.96 20.96 20.96 23.28 23.28 23.28 23.28 27.96 27.96 27.96 19.50 19.50 19.50 19.50 19.50 19.50 19.50 19.50 19.50 19.50 19.50 li.So u.So U.So 11.50 li.So u.So li.So u.So u.So u.So u.So 6.58 6.58 6.58 6.50 6.58 6.58 6.58 6.58 6-SS 6.58 6.58 Distance X is Insertion depth into coupling to Insure pool tire separation of pi|>a ends. Hark iiill be painted around the circumference of the PAD with etandard black ink, and shall be 1/6* wide. Point P to be in line with outside face of coupling. PERSONNEL CTD015452 Page 16 TAPER B For Bureau of Reclamation Only Refer to .'Standard Pipe, Pages 6 and 7 and Standard Coupling, Pages 8 and 9 for dimensions not shown. Harking: CERIAINTEED (Site) x (Size) TAPER | (Class) AC 51m I.D.-l" Inches Hon. fcliao30 ioxB 8.00 12x10 10.00 lied? 12.00 15x12 12.00 lSxllt l6od5 18x15 18x16 lit.00 15.00 lS.oo 16.00 20x18 21x18 21x20 2itx21 18.00 18.00 20x00 21.00 0.00" -o.o5" 10.00 12.00 lit. 00 lS.oo i5.oo 16.00 18.00 18.00 20.00 21.00 21.00 2Ji.OO Tyj>e A <0.125" -0.00" 3.So 3.5o It.00 It.CIO It.So It.So It.So It .So 5.00 5.00 S.oo 5.00 Dimensions 0.00" -0.063" B.O.D." 0.08'' -0.00" 3.SO 3.50 It .00 It. 00 11.14 13.24 15.38 I6.61t It .So it.So It.So It.So 17.60 lS.ltO 19.60 19.60 S.oo S.oo 5.00 5.oo 21.76 22.Bit 23.83 26.08 Size Inches 12x10 lltxl2 15x12 lSxllt 16x15 18x15 18x14 20x18 21x18 21x20 2ltx21 I.D.x" Non. 8.00 10.00 12.00 12.00 lit.00 lS.oo lS.oo 1A.00 18.00 18.00 20.00 21.00 i.d.2" 0.00" -o.oS" &gS-i <0.]25" -0.00" 10.00 12.00 lit .00 15.00 3.50' 3.50 it.00 it.00 lS.oo 16.00 18.00 18.00 It.5o It.So It.So It.So 20.00 21.00 21.00 211.00 5.00 5.00 S.oo 5.00 <0.00 " -0.063' 3.50 3.50 It. 00 It. oo It. So It.So It.So It.So 5.00 5.00 S.oo S.oo B.O.D." <0.08" -0.00" 11.18 13.117 15.44 16.82 17. 17. 19. 19. 2221.. 21t.01 26.06 S3 8SS CTD015453 TECHNICAL SPECIFICATIONS CertainTeedEI CertainTedd Corporation Pipe and Plastics Group SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification T.C.O. REF. NO. 9 SPECIFICATION NO! 15B PACE NO.: 17 SUPERSEDES: January 17, 1978 DATE i3F issue: JAN 1 6 1978 description: A/C Bureau of Reclamation/Fluid Transmission Pipe, Couplings and Accessories Size I.D.!" Inches Not.. Class bO Bx6 6.00 10x8 8.00 12x10 10.00 lbxl2 12.00 *0.00" -o.o5n 8.00 10.00 12.00 lb.00 15x12 l5xl!i 16x15 18x15 12.00 lb.00 15-00 15.00 35.00 15.00 16.00 18.00 18x16 20x18 21x18 21x20 2tix21 16.00 18.00 18.00 ?G.no 21.no 18.00 20.00 21.00 21.00 2b.00 Class US 8x6 6. CO 10x8 8.CO 12x10 10.00 iii2 12.00 B.00 10.00 12.00 lb.00 15x12 15x1b l6xlS 18x15 12.00 lb.00 15.00 15.00 IS.00 IS. 00 16.00 18.00 18x16 20x18 21x18 21x20 2lix21 16.00 18.00 18.00 20.00 21.00 18.00 20.00 21.00 21.00 2b .00 Class 50 T16 6.00 10x8 8.00 12x10 10.00 lbxl2 12.00 8.00 10.00 12.00 lb.00 15x12 lSxlb 16x15 ()8xl5 12.ai lb.00 15.00 15.00 1S.00 15.00 16.00 18.00 18x16 20x18 21x18 21x20 2bx21 16.00 18.00 18.00 20.00 21.00 iO.no 20.00 21.00 21.00 2b.00 Type A H" 0.125" -0.00" 3.50 3.50 3.50 b.00 b.00 b.So b.50 b.So b.So S.oo S.00 5.00 5.00 3.50 3.50 3.5o b.00 b.00 b.So b*50 b-SO b.So 5.00 5.00 S.00 S.oo 3.50 3.5o 3.50 b.00 b.00 b.So b.So b.So b.So 5.00 5.00 S.00 5.00 rat BOHKAU OF RSCIAKATIOK OKI! -- --TAPERS"! j' 9----- *-- Dimensions Type B H" 0.00" -0.063" 8.O.D. *' 0.06" -0.00" 3.50 3.5o 3.50 b.00 b.00 b.SO b.50 b.SO b.50 5.00 S.on 5.oo 5.on 9.26 11.30 13.38 15.44 16.82 17.60 18.67 20.21 20.21 22.82 23.72 25.2b 26.82 3.So 3.50 3.50 b.00 b.00 b.5o b.50 b.50 b.50 5.00 5.00 S.oo 5.00 9.36 11.49 13.70 15.73 17.OS 18.20 19.51 20.21 20. b2 23.20 23.72 25 66 26.93 3.5o 3.50 3.5o b.00 b.00 b.So b.50 b.So b.50 S.oo S.oo S.oo S.oo 9.38 11.52 13.76 15.87 17.36 Jfl.b9 19.62 20.bb 20.69 23.30 23.8b 25.7B 27.25 Si IQ I.D.!" Inches Non. Class 60 6.00 10x8 s.oo 12x10 10.00 lbxl2 12.00 15x12 lSxlb 16x15 18x15 12.00 lb. 00 iS.00 15.00 18x16 20x18 21x16 16.00 18.00 16.00 CIabs 70 UxS-- 6.00 10x8 8.00 12x10 10.00 lbxl2 12.00 15x12 lSxlb 16x15 18x15 18x16 12.00 lb.00 1S.00 1S.00 16.00 Class 80 "Bx5-- 6.00 10x8 8.00 12x10 10,00 lbxl2 12.00 15x12 lSxlb 12.00 ib.00 Class 90 "KPT 6.00 10x8 8.00 12x10 10.00 lbxl 2 12.00 15x12 12.00 I.D.2" 0.00" -0.05" 8.00 10.00 12.00 lb.00 15.00 1S.00 16.00 18.00 18.00 20.00 21.00 8.00 10.00 12.00 lb. 00 15.00 15.00 16.00 18.00 18.00 8.00 10.00 12.00 lb .00 15.00 IS.00 6.00 10.00 12.00 lb.00 15.00 Type A K" 0.125" -0.00" 3.So 3.50 3.So b.00 b.00 b.SO b.50 b.5o b.50 5.00 S.oo 3.SO 3.SO 3.5o b.00 b.00 b.SO b.50 b.50 b.5o 3.50 3.So 3.50 b.00 b.00 b.So 3.So 3.50 3.50 b.00 b.00 Tyoo B o.oo" -0.063" B.O.D.* 0.08* -0.00" 3.50 3.50 3.50 b.00 b.00 b.50 b.So b.So b.50 5.00 5.00 9-32 11.91 lb. 36 17.00 17.81 19.80 71.02 21.02 22.28 2b.79 2b.79 3.50 3.50 3.50 b.00 b.00 b.50 b.50 b.50 b.5o 9.32 11.93 lb.36 17.13 17.66 20.26 21.52 21.52 22.5b 3.50 3.50 3.50 b.00 b.00 b.So 9.b6 12.00 1S.15 17.90 18.b3 20.56 3.50 3.50 3.50 b.00 b.CO 9.62 12.3b 15.15 17.90 18.26 V - 1.00" 4.06 ", -.00" T 1.00" 4-06 ", -.01" 1 .VK* 4.1?< -fYYV1 CTD015454 PREPARED BY: APPROVED BY: 15> 02-10-0023 (P927) 12/76 CONFIDENTIAL DOCUMENT - NOT TO BE DICTRIBUTEO TO UNAUTHORIZED PERSONNEL TAPrED COUPLING WITH 7k" X 2" HEXACONAl BUSHING PhTtcl Requirements Page 18 Coupling shall be hydrostatically tested prior to drilling and tapping and shall meet the requirements of the standard coupling. It Is also intended that couplings shall be able to withstand.the specified hydrostatic pressure after the bushing has been secured. Rubber Rings Each coupling shall be supplied with two (2) rubber rings of the appropriate size and class. 0L1 resistant rings will be supplied when specified by the purchaser. Rote: It is not essential that the coupling be machined on the entire I.D. The dotted line above shows an acceptable machining alternative. X" i .125" for all classes 6" - 10" - 3.50", 12" " 4.00", 14" - 16" 4.50", 18" - 24" = 5.00". tn * 21.00 *.25" -.00* for *31 altsa and ciasaaa or L* IS.00* *.25" -.00* for all sleoa and up to end - including closa 50 when ao apooiflod on an order. For dimensions not shown refer to standard coupling pages. -Class Size 6 8 10 12 14 15 16 18 20 21 24 30 - 11.50 13.90 16.25 18.60 19.80 20.20 23.00 25.40 26.70 30.10 35 40 - 11.50 13.90 ,16.25 18.60 19.60 20.20 23.00 25.40 26.70 30.10 9.25 11.50 13.90 16.25 18.60 19.60 20.20 24.50 26.70 27.90 31.60 * 40.08" B.O.D .q.oo" 45 9.25 11.50 14.55 16.90 19.70 21.20 22.60 24.50 26.70 27.90 31.60 50 9.80 12.40 14.55 16.90 19.70 21.20 22.60 24.50 26.70 27.90 31.60 60 70 9.80 12.40 16.! 23 19.00 20.85 22.40 24.00 26.00 28.30 - 9.80 12.40 16.23 19.00 20.85 22.40 24.00 - - - - 80 10.65 13.50 16.80 19.50 21.35 23.60 24.50 - 90 10.65 13.50 16.80 19.50 21.35 23.60 24.50 - - 2V* x 2M Hexagonal Bushing way be manufactured in: a. Galvanized Iron b. Brass c. Malleable Iron d Stainless Steel Epoxy Formulation Per Cen. Stds, Manual Section "0". Use no asbestos fiber filler. Koto: Must hove clearance vhcu thread is tight. Check threads with go/no-gO gauge. Check visually at "A". CTD015455 TECHNICAL SPECIFICATIONS SPECIFICATIONS CLASSIFICATION: CertainTeedEI CertainTeed Corporation Pipe and Plastics Group A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: PAGE NO.: 9 15B 19 SUPERSEDES: January 17, 1978 DATE OF ISSUE: JAN 1 6 1978 description: A/C Bureau of Reclamation/Fluid Transmission Pipe, Couplings and Accessories Tapped Coupling with 4" x 3" Hexagonal Bushing , For Fluid Transmission Only ------------- L ------------------------------------------ H `/i6. R-klDR/LtiL/o5-o.5"01"t r5W-VCkMarking: CFRTAINTEED (SUe) TAPPED CPLC FT (CUu) FLUID TRANSMISSION _______________3" KPT__________ Bote: It Is not essential that the coupling be machined on the entire I.D. The dotted line above shows an acceptable machining alternative. X" i .125" for all classes 6" - 10" = 3.50", 12" 4.00", 14" - 16" <* 4.50", 18" - 24" = 5.00". 4" x 3" Hexagonal Bushing may be manufactured in: A. GalvaniEed Iron B. Brass C. Malleable Iron D. Stainless Steel Notes: 1. For dimensions not shown refer, to Standard Coupling dimensions 2. Tapped Hole shall be centered on coupling length. Size" Class 3035 B.o.n." +0.0&" -o:oo" 8 11.27 11.27 10 13.83 13.83 1? 14 1C.19 18.C3 16.19 18.63 15 16 18 19.83 19.83 20.95 23.13 20.95 ' 23.13 20 25.46 25.46 21 26.72 26.72 24 30.15 30.15 L" + 0.0C" CTD015456 CIaoo 30 3s 8 13.00 13.00 10 13.00 13.00 12 lli.00 111 .00 Hi .......... 15.00 1S.00 35 --' ' 15.00 lS.oo 16 ----- 15.00 15.00 18 1 16.00 16.00 *" 210** 16.00 16.00 21 1 16.00 16.00 2i| 16.00 16.00 PRCTARCO BY*. 0 APPROVED by: R ft O MFG. SALES I.E. \br OTHERS 02-10-0023 (P927) 12/76 CONFIDENTIAL DOCUMENT - NOT TO BE DISTRIBUTED TO UUNN>AUTHORIZED PERSONNEL THREADED BRASS INSERT COUPLINGS (TniC) Page 20 USE To provide o means for making 6ervlce connect Ions In asbestos cemeuC pressure pipe systems vlierc either NPT or AWWA threads arc employed. PHYSICAL REQUIREMENTS: All Inserts shall be cemented In place with on epoxy adhesive. The workmanship shall be such that there la no evidence of voids or holes, and there shall be no sharp protrusions of the cement on any of Its surfaces. The rubber 0-rlng shall not be placed on the Insert until the Insert it ready to be cemented In place. Coupling shall be hydrostatically tested prior to drilling and cementing the Insure Into position and shall meet the requirements of the standard coupling. It Is el60 Intended that couplings ehn 11 be able to withstand the specific hydrostatic pressure oftcr the Inserts have been cccurcd. RUBBER RINGS: Each coupling shall be supplied with two (2) CC Rubber Rlnga of the appropriate sire and class. Oil resistant rings will be supplied when specified by the purchaser. PLASTIC CLOSURES: Prior to Insertion, storage and/or shipment, each Insert shall be covered with a plastic closure to prevent damage to the brass threads. Plastic closures arc defined in Standard Purchasing Specification No. 525. BRASS INSERTS: Threaded Brass Inserts and Bushings shall meet the requirements of Purchasing Specifications 523A end 562. Threaded Brass Inserts are available in 3/4" and 1" ALVA "A" and "B" lengths, 3/4" NPT, 1" NPT in "A" and "B" lengths, lV NPT in "A", "B" and "C" lengths. In the cases marked (D, a IV HPT insert shall be used and bushed down, if necessary, to the proper sire. In the cases marked the coupling shall be counterborcd, as shewn below, to allow for proper Joining of the Corporation Stop. A "C" length IV HPT insert shall be used and bushed down, if necessary. MARKING Insert site is to be stenciled near the insert. Example: lV'h'l'T. Other marking as shown. .Notes: 1. For machining dimensions not shown refer to standard CG Pipe and Coupling In the specification. 2 TRIC's arc available In any combination of listed inserts and coupling slte9. 3. TUll'A's arc available In any combination of listed Inserts and pipe sizes. 4. Double outlet - Inserts arc to be locateJ 180 apart. .5. Protrusions chall be filleted wlLh epoxy. 6 "J" diameter to be centered on "0". 7. Rubber "0" rings per Standard Purchasing Specification No, 524. PROCEDURE FOR USE OT BUSHINGS Uco normal cleaning procedure for inserts and bushings (degreasing). After shaking the bottle ns directed on the label, apply Loc-tltc <1252 to the second lull thread ol the bushing, filling the thread nearly full all the way around, Srrew the bushing into the lnaert end tighten immediately to about 60*80 foot pounda. If Loc-tlta oosaa outaida the fitting la any noticeable amount, uso laa. Allow 24 houra to cure. CTD015457 TECHNICAL SPECIFICATIONS CertairileedEI CertainTeed Corporation Pipe and Plastics Group SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: 9 supersedes: July 25, 1977 15B PAGE NO.: 21 OATE OF ISSUE: JAN 1 6 1978 description: A/C Bureau of Reclamation/Fluid Transmission __________Pipe, Couplings and Accessories_________ THREADED BRASS INSERT COUPLINGS (TBIC) -M- PULStC CAOJVL 3TICIC* tMK HrtCCr fsi"r 1 J8'03~ BCD 0 Note: For dimensions not shown, refer to Standard Coupling Dimensions. Class Size 6 8 10 12 30 -- 10.75 13.05 15.38 35 ------- 10.75 13.05 15.38 B.O.D." +0.08" -0.00" 40 45 50 60 8.20 10.75 13.05 15.38 8.20 10.75 13.63 16.08 8^80 11.35 13.63 16.08 L" +0.06" 9.30 12.00 15.03 17.85 70 9.30 12.00 15.90 18.80 80 10.25 13.15 15.90 18.30 so 10.25 13.15 15.90 18.80 Class Size 6 8 10 12 30 8.50 8.50 9.50 35 - 8.50 8.50 9.50 Class Size 6 8 10 12- 30 A A A 40 8.50 8.50 8.50 9.50 35 A A A 45 50. 8.50 8.50 8.50 9.50 8.50 8.50 8.50 9.50 Insert Length 40 45 50 AAA AA A AAA A8 B 60 8.50 8.50 8.50 9.50 60 _ B B c 70 8.50 8.50 8.50 9.50 80 8.50 8.50 8.50 9.50 90 8.50 8.50 8.50 9.50 70 80 90 ABB B C Cffl c C c(D @ H" - 6", 8", and 10" All Classes - 5.00" +.00" -.06" 12" All Classes - 6.00" +.00" -.06" CTD015458 Insert Size 3/4" NPT 1" NPT IV NPT * IV NPT 3/4" AWWA 1" AWWA J" .01" 1.335 1.635 2.240 1.635 1.885 D" .03" 2.56 2.56 2.56 2.56 2.56 Marking: CERTAIKTEED TBIC (Size) IT (Class) AC FLUID TRANSMISSION ACRI-FERM PREPARED BY: 3 * IV NTT - Use IV' NPT and bush down to IV KPT. Bushings per Spec 562. APPROVED by: R aD 02-10-0023 (P927) 12/76 CONFIDENTIAL DOCUMENT - NOT TO BE DISTRIBUTED TO UNAUTHORIZED PERSONNEL Page 22 Coupling Adaptor (A/C to Steel) For Fluid Transmission and Agrl Perm Only Markin#: CKRTA1NTEED (S 1*0 FT (Class) AC CFLC ADIT A/C 10 STEEL FLUID TRANSMISSION /.CRI-ITRM gtlD~) located at the adaptor end or___________ tho etcel or piu>tlo Ffra FiCJl pipe ia to ba lnaertod. Adaptor Sira, In. --t-- 6 e 8 10 12 type* and Claes "ITT m *11 All All All _ Ct*l pr Pltia Site. in. O.L*. - TOT 6 6.625 6 6.625 8 8.625 10 10.750 12 12.750 oc t2* rr 13 13 16 16 16 Piconelom V .03" -.01" T7<5~ .63 .63 .63 .63 .63 a Kin. nii? .50 .50 .62 .62 .62 V .03" -.00" .35 .35 .So 5o .50 ** -.010" TT2T .200 .200 .200 .200 .200 e i.025' "5752 7.31 7.31 9.40 11.55 13.55 a 3.025" '(T.56~ 6.69 6.69 6.69 10.81 12.8] c 4 ~sr.er 6.77 6.77 6.78 10.yi 12.92 7.00 7.00 7.00 7.00 7.00 6.00 Adaptor Size, Inches 6x4 6x6 8x6 8x8 10 x 10 12 x 12 30 ' 10.50 10.50 12.50 14.70 B.O. D." -t- .08" - .00' H 40 45 50 - 10.50 10.50 12.75 15.00 8.18 8.18 10.50 10.50 12.7S 15.00 8.18 8.18 10.67 10.67 13.30 15.55 8.40 8.40 10.90 10.90 13.30 15.76 60 8.76 8.76 11.32 11.32 14.36 17.00 70 80 8.76 8.76 11.32 11.32 14.36 17.13 9.35 9.35 12.00 12.00 15.15 17.90 90 9.35 9.35 12.00 12.00 15.15 17.90 Kabber Ring* Koch coupling adapter ehall ba supplied Kith two (2) rubber rings. The ring for the A/C end shall be of CO design of the proper alia and oliei. The ring for the ateol tnl shall be at ah<wn belowt Cwpllnt In. 6r L 6x6 6r6 6x6 10 x 10 12 x 12 flfcael tfrd Rl&g to ha t/tr^pllcd. li" Claso 100 FUJlD-TITE - Std. Purchasing 3pec.Ho.$03-B 6" CAS ring per 3t4. Purchasing Spao. Ko.31 6m CIS ring par Std. Purchasing Spec. Ko. $31 8* Savor ring par Std. Purchasing Spec. Ko. $31 10" Sower tit?, per Std. Purchasing Spec. No. *>31 12" Sower ring per Std. Purchasing Sp>o. Ko. 31 * Oil reeletant rln^ will be supplied when epadflad by the cuetooar. Noteai 1) For axcaesirely oval etaal pipe, field reworking of the Bg to the Cs diAanaloo la pemittad. 2) Ettieenilon* accomodate threaded and coupled, black or galvanised etaal pipe, aehadula 10 through 160. CTD015459 TECHNICAL SPECIFICATIONS SPECIFICATIONS CLASSIFICATION: CertainTeedEH A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: PAGE NO.: CertainTeed Corporation Pipe and Plastics Group 11 SUPERSEDES: 15B April 30, 1979 oncmmoN: A/C Bureau of Reclamation/FIuid Transmission Pipe, Couplings and Accessories 23 DATE OF ISSUE: FEB 1 1982 MOWS Tor Butou or kcTnwtlon Only Refer to Itanderd Plpo, 'ages 4 and 7, for dimension* not shown. 51t. Inches AC 30 B.O.D.*' Min. AC 3S *C liO *li Dimensions c So 1" -0" AC 30 AC 35 Kan. >C liO AC 65 AC SO Slwi, Inches 6 -- .. 7.06 7.06 7.16 32.00 __ ,,,, 6.00 6.00 6.00 8 9.11 9.26 9.26 9.J6 9.38 37.50 8.00 8.00 6.00 8.00 8.00 1l.lt 11.18 II.JO 11.49 11.52 1.3.00 10.00 10.00 10.CO 10.00 10.00 n IJ.M IJ.27 IJ.J8 13.70 13.87 1.7.00 12.00 12.00 12.CO 12.03 12.00 iu IS. 3* IS.M 15. 15.78 15.95 S3.SO Hi. 00 ih. 00 13.ro Hi .00 Hi.00 IS 16 16 :o 21 all MM 17.58 19.60 2I.H 22.8t 26.06 18.82 17.58 19.40 21.67 22.91 26.19 16.72 17.71 20.21 22.1.3 19.59 26.82 17.05 18.07 20.21 22.63 23.72 26.97 17.15 18.22 20.44 22.27 23.86 27.25 56.00 59.00 6!. .00 69. SO 72.00 80.00 lS.co l6.cn lB.uo 20.00 21.00 2ll.0C 15.00 16.00 in.00 20.00 21.00 26.00 15.00 15.50 18.00 20.00 21.00 2lj.00 15.03 16.00 18.CO 20.00 21.00 2i).00 15.00 16.00 18.CO 20.00 21.00 26.00 6 6 10 12 Hi 15 16 18 20 21 aii Pip* Site All All All AU Cleeses All All All All Dofrcoa 11-iA 22-3/2 30 1*5 oc JO S-S'B ll-l/ll IS 22-1/2 20C tS ll-ldi 22-1/2 . 30 65 forking! CETvTALSTEED (Degree) EL ;sa) (cun) ac Hotel 2. RpAxy ell adjoining eurfaeee. Restore excess on inside for smooth surface. I. tingth for oil eiisns. CTD015460 PREPARED by: 02- 10-0023 (P927) APPROVEO BY: n 0 MFO. X- fab 12/76 CONFIOICNTIAL DOCUMENT - NO | SALES 1 jaa I.E. OTHERS rpr Dttrtmi of ''uclxmtlw Only Page 74 Roduolng Kiln Pjjnonalono Refer to Itandard ripe, friges 6 end 7, for dimension* not shown. Hon-fU>duclnE Tee AC )G 1,0.00 56.00 66-00 V. oo 76.00 80.00 58.00 9o.00 100.00 n?.oo L" 1.0" -0.0* " it 35 AU h) AC hS -- liO.OO To. 00 13.00 63.00 68.0.0 56.00 66.00 56.00 6!l.ou 72.00 Ml.00 72.00 66.00 72.00 76.00 7'). CO 76.00 80.00 60.00 80.00 83.00 83.00 88.00 96.00 9n.00 96.00 100.00 112.00 100.00 112.00 100.00 112.00 AC 50 "60.00 68.cn 56.0) 66.00 72.00 76.00 80.00 89.00 96.00 100.00 ` 112.00 Fitting 517a, Inches 6x6x 6 6x8*8 10x10x30 12x12x12 I!ixl6xl6 15x15x13 16x160.6 18x18x18 2-7x20x20 2Jx?1x21 76x16x26 AC jJ -- 13.66 24.46 23.61 23.31 23.78 23.21 26.20 24.12 23.se 24.9* lo" 10.06" AC 35 xiren 23.3/ 24.41 23.37 23.2! 23.69 23.21 26.20 24.06 23.56 24.80 22.67 23 37 26.35 23.31 23.22 2}.64 23.14 23.93 23.81 23.20 26.59 At 65 22.67 23.32 26.27 23.15 23.13 23.48 22 .96 23.93 23.81 23.14 24.SI Ac [>o 22.42 23.31 24.24 23.06 2J.02 23-42 22.89 23.78 23.86 23.OB 24.38 Fitting Slro, Inches 6x6x6 8x0x8 10x10x30 12x12x12 Uixliixlti 15x15x35 1^x16x36 18x18x18 ?0x?0x20 2)x?lx?l ?6x?lix?6 Markingi COSAINTESO xtt rmiKG (Uu) s (Siss) Class) *C IS I88S 888S S 888 |K |S S 8888g8S 88 U" XC33~"IJT ~~lC 66" "66'65 26.00 28.00 32.00 36.00 38.00 60.00 66.00 68.00 So.00 56.00 26.00 28.00 32.00 36.00 35.00 60.00 66.00 68.00 50.00 S6.M 20.00 26.00 28.00 32.CO 36.00 38.03 60.00 66.00 68.00 S0.00 56.00 20.00 26.00 28.00 32.00 36.00 38.00 60.00 66.00 68.00 So.oo S6.00 -75-50 20.00 26.00 28.0.0 32.00 36.00 38.00 60.00 66.00 68.00 So.oo 56.00 it jy -- 78.00 30.00 30.00 31.00 32.00 37.00 36.00 35.00 35.00 38.00 r* nr~xmcr~~vrT.r~"ICTo -- 78.00 30.00 26.00 28^X3 30.00 76.00 25.00 30.00 26.00 26.00 30.00 30.00 30.00 30.00 30.00 33.00 )?.00 37.00 31.00 37.00 32.00 31.00 32.00 32.00 31.00 32.00 32.00 36.00 3S.0O 36.00 35.00 36.00 35.00 36.00 35.00 35.00 35.00 35.00 35.00 38.00 38.00 38.00 35.00 CTD015461 TECHNICAL SPECIFICATIONS fPKCiriCATIONt CLASSIFICATION: CertairiieedOl A/C Standard Product Specification T.C.O, RBF. NO. PACIFICATION NO: CertainTeed Corporation Pipe and Plastics Group 11 ufirbcdcb: April 30, 1979 5B 25 DATI OF lUUi: FEB 1 82 description: A/C Bureau of Reclamation/Fluid Transmission Pipe. Couplings and Accessories 42J2 19.16 m.W. iS-lii 26.31 29.68 31.21 314.20 37.12 38.58 I.2.F1 Ac 3o .. 8.00 10.00 n.oo 111. 00 iS.oo 16.00 IB .00 20.00 21.00 7li.00 TOR BUSEAP or BBCT/KmOW OULT jKon-twilit:\o 1-D" 0.00" - 0.06" nrAC 35 102 AC ^0 .. 19.37 22 .lil 25-37 26.21 29.59 31.03 3i.> 37.12 38.56 Ii2.56 16.67 19.37 22.3S 25.31 28.22 29.59 31.03 33.93 36.31 33.16 62.59 16.67 19.37 22.27 25.15 28.13 29.68 31.01 33.93 36.81 . 38.16 62.59 16.62 19.31 22.26 25.12 20.07 29.3? 30.89 33-78 36.72 36.08 62.38 fitting Slr.e, Inches 6x6x6 6x6x8 10x10x10 12x12x12 16x16x16 15*15*15 lAxlAxlfi 18x16x18 20x20x20 21x21*21 26x26x26 AC 30 __ 28.56 33.56 38.59 63.69 66.32 68.79 53.80 58.88 61.62 69.06 LS" 0.06* --0.00" *C j? ic 6a AC L$ __ 28.63 33.59 38.66 63.79 66.61 68.97 53.80 56.88 61.1*1* 69.06 23.53 28.63 33.6S 38.69 63.78 1*8.1*1 68.97 56.07 59.19 61.86 69.61 23.53 28.68 33-73 38.65 63.68 66.53 69.00 56.07 59.19 61.86 69.61 AC 5o 23.56 23.69 33.76 38.68 63.56 66.66 69.11 56.22 59.28 61.92 69.63 1.0.1 " & T.D.2 " Hon. At 35 A7TE5 AC 1*5 6.00 10.00 12.00 ll.on iS.oo 16.00 18.00 20.00 21.00 26.00 6.00 8.00 10.00 12.00 13.60 IS.OO 15.50 18.00 20.00 21.00 26.00 6.00 8.00 10.00 12.00 16.00 iS.oo 16.00 18.00 20.00 21.00 76.00 AC 56 6.00 8.00 10.00 12.00 16.00 iS.oo 16.00 18.00 20.00 21.00 26.oo Fitting Sire, Inches 6x6x6 8x6x6 10x10x10 12x12x12 lUxlbxll* 15x15*15 16x16x16 18x18x18 20x20x20 21x21x21 26x26x26 B.0.D.1" & B.0.D.2" vryy 1c 60 9.12 II.u 11.26 15.38 16.64 17.58 19.60 21.76 22.8J* 26.08 .. 9.28 If.18 13.27 15.H 16.62 17.58 19.80 21.87 22.9> 26.19 7.08 9.28 11.30 *3.38 t$.U 18.7? 17.71 20.21 22.43 23.59 26.82 Min. 1C 6> 7-06 9*38 11.49 13-70 15-78 17.05 18.07 20.21 22.43 23-72 26.97 "TftTjS 7.18 9.38 11.52 13.87 15.95 17.15 18.22 20. h t* 22.27 23.84 27.25 PREPAREO BY: APPROVEO BY: R *O MFO. J-- BALES J.QA I.E. CTD015462 OTMCRB iJO ... .. 68_.00 60.oo $6.00 .. 66.00 $6.00 66.00 .. 68.00 $6.05 66.00 72.00 .. 68.00 $6.00 66.00 72.00 76.00 AC JO -- 27.00 .. 28.7$ 78.00 .. 30.7$ JO.2$ 29.7$ 31.00 31.00 JO.So 29.7$ 31.$0 31-7$ 31.So 30.2$ 30.So AC JO "" y.i6 9.16 11.10 -9.16 11.10 13.20 - 9.16 11.10 13.20 i$.6o -9.16 11.10 13.20 1S.60 16.1.6 Aw yj 8.00 10.00 12.00 I6.oo iS.oo 16.00 AC 30 ~ 6.00 10.00 12.00 16.00 lS.oo L* *1.0* -0.0N AC 3$ AC ItO 14 US -- \ 68....00 68.00 S.6....00 68.00 $6.00 66.00 .. 68.00 $6.00 66.00 72.00 68.00 $6.00 66.00 72.00 76.00 60.00 6o.oo 68.00 60.00 68.00 $6.00 60.00 68.00 $6.00 66.00 6o.oo 69.00 $6.00 66.00 72.00 liO.OO 68.00 $6.00 66.00 72.00 76.00 6o.oo 6o. co 68.00 60.00 68.00 $6.00 .60.00 68.00 $6.00 66.00 60.00 68.00 $6.00 66.00 72.00 60. on 68.00 $6.00 66.co 72.00 76.00 _______ AC 50 60.00 60.00 68.03 60.00 68.00 $6.00 ho. 00 68.00 S6.00 66.00 bo.oo 68.00 $6.00 <6.00 Ti.ro 60.00 68.00 $6.00 6u.00 72.00 76.00 F" '1C 5$'--jnrnr"-TTCTS- ' ... 26.00 26.00 27.50 27. $0 27.00 .. 27.00 29.00 27.00 29.00 28.7$ 76.7$ 28.7$ 28.00 20.00 2C.OO 30.CKJ 30.00 10.2$ 30.2$ 10.7$ 30,2$ J0.7$ 29.25 .. 29.2$ 30. $0 29.2$ 30. $0 31.00 31.00 31.00 31.00 31.00 31.00 30. $0 30.$0 30. $0 29.7$ -- 29.7$ 31.2$ 29.7$ 312$ Jl.SO 31.$0 Jl.SO 31.7$ 31.7$ 31.7$ 31.$0 31.SO 31. $0 30.2$ 30.2$ 30.2$ 30. SO 30.$0 30.S0 Acid' 26.00 27.50 27.00 29.00 28.75 28.00 30.00 30.7$ 30.7$ 79.25 30.50 31.00 31.00 30. So 29.75 31.25 31.50 31.7S 31.50 30.2$ 30. $0 15" .0V\ -.01" 1C 3$ 9.28 9.28 11.20 -- 9.20 11.20 13.29 -- 9.28 11.20 13.29 IS.60 -- 9.20 11.20 13.79 IS. 60 16.64 1C 60 T.08 7.08 9.28 7.08 9.28 11.32 7.08 9.28 11.32 13.60 7.08 9.28 11.32 13.60 IS. $8 7.03 9.28 11.32 13-60 IS.SB 16.7^ *J& 7.08 7.08 9.38 7.08 9.38 11.66 7.08 9.38 11.66 13.72 T.OS 9.30 11.68 13.72 IS.77 7.00 9.38 11.68 V3.72 IS. 77 17.07 7.18 4.40 7.l 9.40 11.54 7.18 9.40 II. $6 U.89 7.1# 9.60 11.56 13.89 15.97 7.18 9.40 11. $6 13.89 15.97 17.17 1. AC 35 8.00 lo.ro lr.oo 16. eo iS.oo 16.00 AC 60 8.30 70.00 12.00 13.60 IS.oo i$.$o AC Uc. 0.00 10.00 12.00 111.00 15.00 16.00 AC $0 3.00 10.00 12.00 16.00 lS.rxj 16.00 I.,n.?N No.n. --*5To -- 6.-0 8.00 8.00 10.00 10.00 12.00 12.00 i6.no IS.oo 15.00 I.C'VT 6.O') 8.00 10.00 12.00 16.00 IS.oo 1C 55 6.00 8.00 10.00 32.00 16.00 15.00 RndvcJnrT Page 26 Kit. tine Si**, Inches 8x6r4 10x10x6 10x10x8 12*17x6 12x17x8 12x12x10 llixl Iix4 l6xl6x0 l6rllix:0 16x16x12 I$xl5x6> l5xi5x0 lSxlSxlO 1$xl5x12 l>xl5x] ll 16x16x6 14x14x8 16x16x10 16x16x12 16x16x16 16x16x15 ____ AC 30 26.00 .. 26.00 28.00 .. 76.on 28.00 32.00 26.oo 2B.OO 32.00 36.00 26.CO 28.00 3?. oo 36.03 33.00 IAtc 35 AC Lo .. 26.00 .. 26.00 23.00 __ 76.00 28.00 32.00 .. 26.00 73.00 32.00 36.00 -- 76.00 23.00 32.00 36.00 33.00 20.00 20.00 26.CO 20.00 26.00 28.00 20.00 26.00 28.00 32.00 20.00 26.00 20.00 32.00 35.CO 20.00 26.00 28 .CO 32.00 34.00 38.00 AC 6$ 20.03 20.03 26.00 20.00 26.00 28.00 20.00 26.00 28.00 32.00 20.00 26.00 28.00 3?.CO 36.00 20.00 26.00 26.00 3?. 00 36.00 38.00 * ac'56 20.00 20.00 26.00 20.00 26.00 2e.oi 20.00 76.00 28.00 32.00 20.00 26.00 23.CO 32. CO 36.00 20.00 26.00 29.00 32. M 36 .CO 38.00 Fitting Size. Inches 8x8x6 10x10x4 10x10x8 12x12x6 12x12x8 12x12x10 lliXl Iix4 16x16x8 16x16x10 16x16x12 lxl5x4 15x15x8 15x15x10 15x15x12 l$xl$xl6 16x14x4 16x16x8 14x36x10 16x16x12 lfxlfxlij 16x16x15 AC 30 .. 22.00 ... 22.75 2?.00 .. 23.2$ 23.2$ 22.25 .. 23. SO 23.50 23.00 22.2$ -23.50 23.7$ 23.50 22.2$ 22.50 LC 8.2?* - *05 AC .. 22.03 -- 22.50 22.00 ... 22.00 23.00 22.7$ 22.00 .. 22.75 22.00 23.00 73.25 2>.2$ 22.2$ -- 23.50 23.50 23.00 ?3.2$ 23.2$ 22.29' 23.00 23.50 23.50 23.00 22.2$ .. 23. So 22.25 23.25 23.50 23.7$ 23.50 23.7? 23.50 22.2$ 22.25 22.50 22.$0 to 65 22.00 22.50 22.03 23.00 22.7$ 22.00 23.00 23.2$ 23.25 22.2$ 23.00 23. SO 23.50 23.00 22.2$ 23.25 23.50 23.TS 23.50 22.2S 22.$0 ~AC~?0 22.00 22. $0 22.CC 23.00 22.7$ 22.00 23.00 23.2$ 23.75 27.2$ 23.00 23.50 2J.SO 23.00 22.2S 23.25 23.50 23-7$ 23.50 22.2$ 22.50 Fitting Site. Inches 6x8x6 10x10x6 10x10x8 12x12x6 12x12x8 12x12x10 lijxliixf lJjxlUxO 16x16x10 16x16x12 l$xl$x6 15x15x8 i$xi$xio 15x15x12 l$xl$xl6 16x3 toc6 16x16x0 16x16x10 16x16x12 IfoclAxlb 16x16x1$ *lf existing core drills are not the proper size, machine branch end to fit or use oversize stock, as the s i tua tion warrants. Help Sirn, Inches 8x8 10x10 1?.\12 16x16 l$xl$ 16x16 li.O.D.l" Kin. 13} "Ti!3i "Tcnr* ACJil 9.12 11.14 l).6 15.JB 16. 6t 17-58 9.26 n.ie IJ.27 15-66 16.62 17.58 9.16 11.30 11.JB 15.u 16.72 17.71 9.36 11.69 19.70 15.76 I?.OS 18.07 At'$6 9.J8 n.M 11.87 15.95 17.15 11.22 Pnnflt "l.p, Inches 6 8 10 12 16 1$ *or 9.12 ll .14 t).24 19.38 rt.tt B.O.O.?" Hln, __ 9.26 11.18 TTLo 7.06 9.|A 11. yo 13.27 IS.AS 11.JB 15.6* 16.(2 16.72 AC In 7.06 9.36 11.69 13.70 15.78 17.0$ ACJO 7.18' 9-38 II.SI 11.87 I5.9S 17. IS CTD015463 TECHNICAL SPECIFICATIONS specifications classification: CertainTeedEI A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: PAGE NO.: CertainTeed Corporation Pipe and Plastics Group 9 supersedes: 15B description: July 25, 1977 A/C Bureau of Reclamation/Fluid Transmission Pipe, Couplings and Accessories 27 DATE OF ISSUE: JAN 1 6 1978 3" and 4" Direct Tap Couplings Type 25, and Classes 30 and 35 See Hote #2 -U Drill Size for 3" Direct Tap Coupling = 3.25" Marking Example: Drill Size for 4" Direct Tap Coupling - 4.25" CERTAINTEED (3" or 4") DIRECT TAP CPLG (Size) FT (Class) AC B.O.D." 40.OS" -0.00" FLUID TRANSMISSION AGRI-PERM Size'* Class 8 10 12 14 15 16 18 20 21 24 30 11.27 13.83 16.19 18.63 19.83 20.95 23.13 25.46 26.72 30.15 35 11.27 13.83 16.19 18.63 19.83 20.95 ' 23.13 25.46 26.72 30.15 Size" Class 30 35 8 8.00 6.00 M" +0. 00" -0. 06" 10 8.00 8.00 12 9.00 9.00 14 9.70 9.70 15 9.70 9.70 16 9.70 9.70 18 10.70 10.70 20 21 10.70 10.70 10.70 10.70 24 10.70 10.70 Size" Class 30 35 8 11.50 11.50 10 11.50 11. io 12 12.50 12.50 L" + 0.06" 14 13.50 13.50 15 13.50 13.50 16 13.50 13.50 .JJL 14.50 14.50 20 14.50 14.50 21 14.50 14.50 24 14.50 14.50 Kotcg; 1, For dimensions not shown, refer to Standard Coupling dimensions d&rPREPARED BY 2. Counter bore each tap to a depth that allows the first full thread engagement. Use a 3,5" counter bore for a 3" tap, and a 4.5" coimrA*- bore for a 4M tap. CTD015464 3. Use KPT (ITT) threads. APPROVED BY'. 02-10-0023 (P927) 12/76 confidential DOCUMENT - NOT to be distributed to unauthorized personnel Page 28 Rubber Rings COJPIIM3 RgWCgRS - FID TP TRANSHTSSTOH TO FlUID TRANSMISSION nxrn>for transkissiqi ovi r Harking Each coupling. r*yv2<u shall le supplied with on (i) rubber rir^ of the Appropriate corresponding with tho coupling aide. An oil resistant ling will bo supplied when specified by trie purchaser. curtajutted CUD CI.A.rS (Sir.c) FT - (Size) FT FuriD-T[Vvfr.::issiON AGKI-i Uu-l Reducer Site, In. 4 .063" Type 25 and All Classes + ^13** Type 25 r.r.d All Classes Type 25 Classes 3Q-3S Ncrc. T. D. " Cl.isscs Classes 40-4S 50-60 Classes 70-90 Type 25 C1 J S i C 5 30-35. B.O.P.*1 *- .OS1* -.0-3" Claeses Classes 40-45 ' 50-30 Classes 70-5-0 8 to 6 10 CO 8 12 co 10 16 co 12 15 Co 14 16 to !* 16 co 15 18 to 16 20 to 13 21 co 20 24 to ?i 6.50 6.50 7.CO 7.75 8. CO 8. CO 8.00 5.00 IQ. CO 10. CO 10.00 CTr?* 25 only) 3.50 3.50 3.50 4.00 4.50 4.50 4.50 4.SO 5.00 5.CO 5.00 6.60 0 8.70 10.60 12.70 14.50 14.50 15.50 16.80 19.CO 21.CO 21.80 6.60 8.70 10.60 12.70 14.90 14.90 15.90 16.CO 19.60 21.CO 23.00 6.SO .30 9.00 9.00 11. CO 11.50 13.20 13.60 15.00 15. CO 15.30 15.50 15.90 15.SO @ 17.40 - 19.60 - 21.00 - -- 9.26 11.18 13.27 15.44 17.60 17.94 10.40 19.80 21.77 24.01 26.08 9.36 11.49 13.70 15.78 18.20 18.20 19.51 20.42 23.20 25.66 26.93 0 (class 50 only) (5) (class 70 oaly) 9.32 11.91 17.00 19.80 19.80 21.02 22.28 24.79 27.07 -- 9.62 12.34 15.15 17.90 21.06 21.06 21.52 0 __ -- ott: a) For machining dimensions not shown refer to standard pipe and coupling this specification. B) .D. subject to manufacturing tolerances, machining of I.D. not required on pipe side. C) Physicsl Jtcqulrcraents - Coupling Reducer shall be designed to meet the hydrostatic test requirements of the Appropriate class. CTD015465