Document dvoQbQ1gyOLNeL5Mb45wd4Q9

>300 U. S. Flexible Metallic Tubing Co., Keflex Mfg. Div. Expansion Joints ' KEFLEX EXPANSION JOINTS Corrugated, Packless Type FOR STEAM AND HOT WATER HEATING SYSTEMS AND PROCESS PIPING KEFLEX packless type Expansion Joints are made from highly flexible laminations of Type 321 or 347 stabilized stainless steel. Standard equipment in both KEFLEX Types 158 and 308 consists of a packless type, stainless steel bellows; weld ends or carbon steel flanges: self guiding, full bore, flow liner; and self equalising contour control rings in sizes over 4 in., also available for smaller sizes. Type 308 reinforcing shoulder rings. Sizes 2 in. through 48 in. The force to compress KEFLEX Expansion Joints is usually less than 100 lb. Rigid flanges supplied on standard Types 15S-12E and 15S-15-12E assemblies have a series 15 drilling, but with special elongated bolt holes to permit easy installation in the event companion flange bolt holes are misaligned. TYPE 15S-9B I5S-1S-9Z 15S-I2E I56-I5-12E Overall Sixes rL-esngfyth-r Working Pressure pmg Temperature Fahr. Traverse Compression Rvteraann tt.00* 13.00* 150 2.00* o.so* lUi..7tSy* 150 4l..ooor* 7.75* 6.75* ISO too* 0.50* 14.00* u.oo* 150 ?oo* 1.00* ^*g*fj If5??} 308-9E 308-1S-9E 308-14E 308-15-14E When flanges are required, Type 308 is fitted with lap joint or swivel flanges. 150 lb type is standard; 300 lb type and heavier are available. J0S-9E J06-15-9E 308-14E jr*-i5-iE Overall Length Sixes r-syi'-r .Sixes IM*-*4* tod. ar.giwxwwi Working Pressure psig ii.^mnwi Temperature Fahr. Trarene Cnmpminna Extendtm t*.so* 14.00* sao 900 2.00* o.so* a.oo* 23.00* 200 8004.00* 1.00* 14.50* 14.00* 200 500 2.00* O.SO* KEFLEX ANCHOR BASE UNITS (INTERMEDIATE TYPES) 308-EAB-9E 158-EAB-12E 308-CAB-14E KTO 300-EAB-2E (Patenl Pending) KTO 300CAB-2E (Patent Pending) KTO 300-15EAB-14E (Patent Pmdins) KTO 300-ISCAB-14E (Patent Pending) . Expansion Joints li. Sr Flexible Metallic Tubing Co* Keflex Mfg, Div. 301 KEFLEX-KETROL CONTROLLED EXPANSION JOINTS FOR EXTRA SAFETY POSITIVE PROTECTION AGAINST TORSION. FOR USE IN PIPE UNES TO COMPENSATE FOR EXPANSION AND CONTRACTION (Patent Pending) KEFLEX-KETROL, self guiding, anti-torsion, packless type, expansion joints are manufactured with multi-ply. Type 321 or 347 stabilized stainless steel and enclosed by a special alloy steel shroud having two matched sections. Each section has at least four equally spaced finger-type projections at one end, which fit axially into the space between the finger projections of the companion section so as to serve as a positive guide to the bellows element and prevent torsion and deflection. The shroud cage also protects the bellows from exterior damage. The lengths of the finger projections determine the full extent to which the bellows may be compressed, and also provide sufficient travel to accommodate extension of the bellows in the event ambient temperatures drop below normal and the pipe lines contract accordingly. Steel nngs to prevent over extension of the bellows element are attached to the ends of the finger projections of each companion section. The rings also maintain complete concentricity of the matched shroud-cage and insure structural stability. KTO-150-2E KTO-1SO-1S-2E KTO-1SO-L2E KTO-150-15-12E Rigid flanges supplied on standard Types KTO-150-I2E and KTO 150-15-12E assemblies have a series 15 drilling, but with special elongated bolt holes to permit easy installation in the event companion flange bolt holes are misaligned. Overall Lenitb sue* r-w-r Sam I)i*-J4* lad. Msrimnm Working Pressure U MT>nx>TT. Tempoatare F Tern.vet* Cotapremioa STANDARD UNITS KTCMSO-I5-2E ' KOI i.otr 0.50* KTO-300-2E KTO-300-1$->2E KTO-300-14E KTO-300-15-14E When flanges are required, KTO 300 are fitted with lap joint or swivel flanges. 150 lb type are standard;'300 lb type and heavier are available. STANDARD UNITS _ KTO-SXMJ-2E KTO-300-15-KE Sires Ipel. Maximum Warking Pressure D> Maximum Temperature F Traverse Compres-oa TYPE KTO 450 Pressures to 450 psig--Temperatures to 800 F. For 2 in. Traverse in Compression and )4 in. in Extension Type KTO-450-2E with Ends Beveled for Welding Type KTO-450-14E with 300 lb, Type Lap Joint Flange For 4 in. Traverse in Compression and 1 in. in Extension Type KTO-4SO-15-2E with Eads Beveled for Welding Type KTO-450-15-14E with 300 lb, Type Lap Joint Flange NOTE: Type 450 measurements are essentially the g>>rn M type 300 listed above, except 450 standard flanges are series 30 (300-Ib type)