Document dQzzzb8w4YQa2Vje8L4EJ4126

Pipe and Tubing, Copper The American Brass Company General Offices--Waterbury, Conn. Manufacturing Plants: Ansoni*. Conn., Tobbinqton, Corn.. WiraanunT, Conn.. Bofvalo, N. Y., Detroit. Mich., Kenosha, Wb. Boston. Mass.. One Forty Federal St. Syracuse, N. Y., 207 E. Genesee St. Providence, R. I., 131 Dorrance St New York. N. Y., 25 Broadway Newark, N. J., 20 Branford Place Philadelphia., Pa., 117 South 17th St. Offices and Agencies: Washington, D. C,. 1511 K St, N.W. Atlanta, Ga,, Forsythe & Walton Sts. Pittsburgh, Pa., 535 Smithfield St. Cleveland, Ohio, 925 Euclid Ave. Datton, Ohio. 32 North Main St Cincinnati, Ohio. 101 West 4th St. Chicago, III., 1326 W. Washington Blvd. Sr. Louis, Mo., 408 Pine St Houston, Texas, 601 Fannin St San Francisco, Calif., 235 Montgomery St. CANADIAN PLANT: Anaconda American Brass Limited. New Toronto. Ontario PRODUCTS--Anaconda Deoxidized Copper Tubes and Fittings; Anaconda "85" Red-Brass Pipe; Anaconda "67" Brass Pipe; Everdur Metal for storage heaters, storage tanks, ducts and air conditioning equipment and A.S.T.M. Spec. No. B-88-33. Ana conda Type K Tubes are recommended for: ANACONDA DEOXIDIZED COPPER TUBES After studying performance records. The American Brass Company endorses Anaconda Copper Tubes, connected with solder fittings, in sizes up to 2 in. where conditions ofpressure and heat are normal. Copper Tubes available in long lengths and coils may be bent for ordinary turns and offsets, offering obvious installation advantages. Anaconda Copper Tubes are drawn to the accurate size required for use with solder-type fittings. Anaconda Copper Tubes are furnished in two wall thicknesses--Type "K" and "L." Type K, the heavier, conforms to U. S. Government Spec. No. WW-T-799 1. Underground water service lines. .2 Hot and cold water lines. .3 Sprinkler systems. .4 Low pressure steam lines. 5. Oil Burner suction and return lines. Anaconda Type L Copper Tubes meet Government and A.S.T.M. Specifications for this class and are considered suitable for interior plumbing, although the heavier grade, Type K, is preferred. Data on the comparative wall thicknesses and weights are included in the accompanying table. Lengths and Coils--Anaconda Deoxi dized Copper Water Tubes in sizes up to and including 1H in. are furnished soft in 30, 45 and 60-foot coils; also hard or soft in 20-foot straight^ lengths. Sizes over \\i in. are furnished'hard or soft only in 20-ft. straight lengths. Weights of Anaconda 67 Brass, 85 Red Brass and Copper Water Tubes Diameters--Inches S.P3. Pipe Copper Water Tubes TypeK TypeL Outside Inside Outsidel Inside Outside Inside Wall Thickness Approx. Weights--Pounds per Foot Inches Copper Water S.P.S. Pipe Copper Water S.P3.\ Tubes Pipe 67 85 Red Type K Type L [Type K Type L Brass ' Brass Copper! 0.405 0.281 0.250 0.186 0.250 0.200 .0620 .0320 .0250 0.540 0.375 0.375 0.311 0.375 0.315 .0825 .0320 .0300 0.675 0.-494 0.500 0.402 0.500 0.430 .0905 .0490 .0350 .8 0.840 1.050 1.315 0.625 0.822 1.062 0.625 0.875 1.125 0.527 0.745 0.995 0.625 0.545 0.875 0.785 1.125 1.025 .1075 .0490 .1140 .0650 .1265 .0650 .0400 .0450 .0500 1.660 1.368 1.375 1.245 1.375 1.265 .1460 .0650 .0550 1.900 1.600 1.625 1.481 1.625 1.505 .1500 .0720 .0600 2.375 2.062 2.125 1.959 2.125 1.985 .1565 .0830 .0700 r* 2.875 2.500 2.625 2.435 2.625 2.465 .1875 .095 3.500 3.062 3.125 2.907 3.125 2.945 .2190 .109 4.000 3.500 3.625 3.385 3.625 3.425 .2500 .120 .080 .090 .100 4.500 4.000 4.125 3.857 4.125 3.9Q5 .2500 .134 .110 253! 0!259 0.085 450 0.460 0.134 630 0.643 0.269 938 0.957 0.344 270 1.300 0.641 .790 1.830 0.839 630 2.690 1.040 130 3.200 1.360 .140 4.230 2.060 .000 6.140 2.920 .560 8.750 4.000 .170 11.410 5.120 .660 12.940 6.510 0.068 0.126 0.198 0.284 0.454 0.653 0.882 1.140 1.750 2.480 3.330 4.290 5.380 Nora--S.P.& Pipe available up to and including 12 in. Copper Water Tubes up to and including 8 in. Other seamless tubes up to 26 in. I.D. 870 Pipe and Tubing, Copper A The American Brass Company anaconda copper tube FITTINGS A complete line of Anaconda Fittings, both solder and flared tube types, is available for the assembly of copper tubes. For size range of fittings, see accompanying table. All three following types of fittings are furnished in elbows, tees, couplings and unions, including a complete range of reduction and adapter combinations. Solder fittings are checked with maximum and minimum gages to insure accuracy and the close tolerance required for dependable solder connections. a moderate price and is recommended for use in localities where highly corrosive water conditions prevail. These waters may be relatively low in hardness, high in carbonic acid gas content and low in alkalinity. Anaconda "85" Red-Brass Pipe con tains 85 per cent copper and conforms to government specifications for Grade "A" water pipe. The words "Anaconda 85 Red-Brass" are stamped in the metal at intervals of one foot throughout each length. ANACONDA "67" BRASS PIPE Wrought Copper Solder Fittings-- Provide copper to copper connections, are uniform in quality and free from porosity. Generous depth of cup and unusually high shoulder give well made joints an extra factor of safety. Anaconda "67" Brass Pipe can be depended upon to give lasting service in all localities where normal water conditions prevail; that is where the water has a low permanent hardness and a fair degree of temporary hardness, is low in carbonic Cast Bronze Solder Fittings--Are made of "steam bronze " alloy (85 per cent copper, 5 per cent zinc, 5 per cent tin and 5 per cent lead). All cast fittings are care fully gauged and checked by air pressure under water. Test joints in.) withstood a straight pull of 7000 lb. at 70 F. and 1500 lb. at 210 F. At all temperatures between 70 and 210 F., test joints withstood in ternal pressure exceeding 2000 p.s.i. Solder--That used in the foregoing tests was 95 per cent tin--5 per cent antimony-- the alloy recommended for best all-around results. Melting point is 465 F.; cooling range is only 15 F. "Hard" solder is, of course, ideal, and where unusually high temperatures are en countered, it is recommended that a high strength, high melt point solder such as Sil-Fos be used (1300 F.). Cast Bronze Flared Tube Fittings-- Serving a definite need for assembling soft tubes in sprinkler systems, under ground lines, etc., these fittings are also made of "steam bronze" alloy. acid gas content and relatively high in alkalinity. Anaconda "67" Brass Pipe contains 67 per cent copper and conforms to government specifications for Grade "B" water pipe. It can be identified by the numerals "67" following the name "Anaconda" stamped in the metal every 12 in. in each length. *Everdur Tanks--Nearly all copper, Everdur is a special non-rust alloy which combines the strength of medium carbon steel with ready weldability. It is an ideal material for durable, rustless water tanks of every description--from domestic range boilers to giant storage heaters for hotels, laundries, hospitals, textile plants, schools or breweries. Everdur is made in all commercial shapes, including tank plates which meet the physical requirements of the A.S.T.M. Boiler Code, Flange Plate Specifications, and S.A.E. Specifications 1010 and 1015. For additional data, and names of fabri cators, address our nearest office. Anaconda Deoxidized Copper Tubes-- Types "K" and "L"in. to 8 in. incL Anaconda Wrought Copper Solder Fittings--------------------- -------------------- in. to 2 in. incL Anaconda Cast Bronze Solder Fittings.... in. to 6 in. incl. Anaconda Cast Bronze Solder Valves: Gate Valves___ H `n. to 2 in. incl. Globe and Stop and Drain Valves___ in. to 1 in. incl. Ananconda Cast Bronze Flared Tube Fittings----------------____ _ )/& in. to 2 in. incl Everdur for Air Conditioning Equip- ment--Everdur Metal has been used with marked success for fans and blowers, ducts, humidifiers (air washers) and for various cast and wrought parts of other equipment items subject to corrosive influences. Because of its strength and welding properties, Everdur may. be substituted for steel in the same gauges, fabricated by ANACONDA "85" RED-BRASS PIPE Anaconda "85" Red-Brass Pipe is offered as the highest quality corrosionresistant pipe commercially obtainable at substantially the same methods, and with the same equipment. "Everdur" is a registered trademark identifying pro ducts of The American Brass Company made from alloys of copper, silioon and other elements. 871