Document byorjye8qLy492w7wdR7x8K16

April 11, 1975 Dept- 5429 TWX Prom: E.M.Begnaud Cleveland A. Vittone R. D. Scott . B. Osborne It* J. L. Nelson /#JK. Greene T .H. Smith E. W. Harrington T. R. Linak P. Terry P,^5. Weaver iSZ. Waltemate J. F. Malone W. S. Lodge W. F. Brune L. W. Hardesty B. C. Birkmeier/R. A. Ellis R. J. Solak R- L. Toole A. L. Hatfield G. S. Ramsey N. G. Duke R. L. Steller R. J. Gerbick H. J. Fast - Akron WHB-6 R. N. Rylands - ALGC R. S. Mather - ii M. W. Ross - ii R. M. Sandfry - M P. W. Shore - II R. M. Kreager - ALTC L. A. Bennett - i D. J- Barnicki/H. F. Gough C. B. Vrabel - n C. B. Cooper - Henry L. R. Mitchell _ H M. Tawney - 11 A. R. Webber - Pedricktown W. E. Kenney - II * C. L. Woods - Calvert City F. R. Carvell -_ n G. E. Evens - ii A. W. Clements - Long Beach E. L. Beeler - <1 P. H. Lawrence - Lvlle. P. A. Wagner - " D. A. Brooks - Kitchener F. M. Fister T. F. Dowse - M R. A. Krueger - Brecksville W. R. Holstein/R. Grahek - Lvlle. Re: REVISIONS TO OSHA LABELING INSTRUCTIONS It has been decided that the following instructions be followed covering the specific products listed: Geon Latex 660X1, 660X2 and 660X4 should not contain the previously specified OSHA label. These latices do not contain vinyl chloride and are, therefore, not applicable to the regulation. Hycar Acrylic Latex 2600X189 should be labeled according to previous instructions covering Geon latices. This is the only Hycar Latex that will require the OSHA label. In an effort to clear up some recent confusion concerning some Geon product groups, the following Geon Polyblend Compounds should not be labeled: 8720-021, 8720-022, 8720-239, 8720-250, 8720-288, 8720-289. The following materials now classified as Flexible Geon Compounds should be labeled: 8880-021, 8880-288 and 8878-288. These two items were previously classified as Polyblend Compounds. If there are any questions concerning the labeling of these or related items, please contact us. M QArrr, n u/1 Mfir WH P . & PkJ. NGC 16414 April 11 1975 Dept. 5429 TWX From: E. M. Begnaud Cleveland To: J. K. T. E. 4: J. w. w. L. B. R. R. A. L. Nelson Greene H. Smith W. Harrington J. Weaver Waltemate F. Malone S. Lodge F. Brune W. Hardesty/W. F. McPherson C. Birkmeier/R. A. Ellis J.Solak L. Toole L. Hatfield P. H. Lawrence - Lvlle. P. A. Wagner - " F. M. Fister - W. R. Holstein - " R. N. Rylands - ALGC R. S. Mather - " R. M. Sandfry - " M. W. Ross - " C. B. Cooper - Henry L. R. Mitchell - Henry A. R. Webber - Pedricktown W. E Kenney - " A. W. Clements - Long Beach E. L. Beeler - M Re: APPLICATION OF PERMANENT OSHA LABELS TO RAIL CARS An audit of several plants indicates that some rail car labeling has possibly not been up to the expected standards. The labeling of top hatches normally appears to be satisfactory. Labeling of the discharge outlets is frequently questionable. The suggested labels, BFG Form No. 16611, should only be applied to the slope sheet after the 3" X 5" area for label placement has been thoroughly cleaned. Pressure-sensitive labels will not adhere to a dirty area. It is acceptable for these labels to be applied to an area of the discharge chute above the bolted flange if the area below this flange is excessively dirty and cannot be easily cleaned. A suggested method for applying the labels was furnished by the supplier with each shipment to our plants. Please follow these instructions closely for secure adhesion of the label to the car surface. E. M. Begnaud Manager, Whse. & Pkg. NC 1641S \ . -f* April 11, 1975 Dept. 5429 From: E. M. Begnaud Cleveland TW X A. Vittone E. B. Osborne J. L. Nelson K. Greene R* D. Scott T* H. Smith E. W. Harrington T. R. Linak P^J Weaver Waltemate J. F. Malone W. S. Lodge W. F. Brune L. W. Hardesty/W. 1`. McPherson T. Tomson B. C. Birkmeier/R. A. Ellis R. J. Solak R. L. Toole A. L. Hatfield H. J. Fast - WHB-6 Akron P. H. Lawrence - Lvlle. P. A.' Wagner - Lvlle. F. M. Fister - II W. R. Holstein _ tl R. N* Rylands - ALGC R. S. Mather - n R. M. Sandfry - it M* W. Ross - it C. B. Cooper - Henry L. R. Mitchell n A. R. Webber - Pedricktown W. E. Kenney - II A. W. Clements - Long Beach E. L. Beeler - ii D. A. Brooks - Kitchener Subject: LABELING OF PVC SHIPMENTS TO ARMSTRONG CORK Armstrong Cork has requested that all shipments of PVC received at their plants contain the required OSHA label on every oag. Please put this procedure into effect immediately. All shipments of Dispersion, Pearl and Mass Resins plus Geon Compounds should contain labels on every bag. The following orders are currently in our system for shipment at a future date. Any new order will contain the statement "Label Each Bag With The Required OSHA Statement." This information will be in the Special Instructions area of the order. F.O. Shipping Product Location Date of Quantity Shipment Armstrong Cork Co. Lancaster, Penna. P097215 P097256 P097264 P097272 P097280 140X30 124F1 124F1 124F1 124F1 P * town. ALDC ALDC ALDC ALDC 40,000 40,000 40,000 40,000 40,000 4/23 4/DO* 4/DO* 4/DO* 4/D0* *Tentative The Marketing group is working with this customer toward convincing them to accept our standard methods of labeling so as to meet the OSHA requirements. E. M. Begnaud Mgr., Whse. & Pkg. NOC 16416