Document byaRM1wbm8E2v0p46vkjk2D4O

968 CHAPTER 45 s r , 1953, Guide Table 1. Temperatures, and Humidities Applicable to Industrial Air CoNDiTiONiNG~r(Continued) Process . , Temp. F PRECISION MACHINING (Continued) R.H. % Precision gear drive assembly...................................... Watch main snrinir MlihrAtinn Gage room........................... Precision parts--honing............................ 78 75-80 45-50 45-50. 1 42-50 . 45 35-45 For general manufacturing and assembly areas no attempt is made to oontrol conditions during hot weather. An ample supply of outside air ana air motion are relied upon to provide personal comfort. Low relative humidity is usually maintained to prevent corrosion. Temperature control within a narrow range is more important than temperature maintained. Dust control is required wherever polishing operations occur. Air distribution is important to maintain constant conditions throughout the area. Process - Pressroom: Multicolor offset Uthogranhv ........ Other sheet fed printing ............ Stock room: PRINTING Binding, cutting, drying, folding and - cdmn* 6 to 8% above pressroom D same as pressroom Temp. F 75-80 75-80 73-80 73-80 R.H. % 46-48 . 45-50 50-55 ft 5-8% above pressroom 45-50 Lithography requires constant humidity control of entire pressroom with paper conditioned 5 to 8 percent higher relative humidity at start. All printing requires conditioned paper otherwise it will not lie flat, with 40 to 45 percent R.H. low limit to eliminate static electricity; and 60 percent R.H. high limit to prevent swelling of the rolls and slow ink drying. Temperature is not critical, but extremes should be avoided due to softening of the rolls at high temperature and improper ink distribution at low temperatures. Hoods must be provided for:gas dryers, with solvent recovery recommended for all except job shops. Exhaust system with dust collectors incorporated is required for type and plate cleaning areas. Check use of gasoline and other solvents. -, Summer--winter central systems are recommended foT all except job Bhops where unitary equipment with heating coils and humidifiers may be used. Normal air cleaning is adequate. Air distribution must prevent drafts on paper in storage or process. Gas flame dryers impose unusual loads. Air from press and storage rooms should not be recirculated through office areas. Testing Process Temp. F REFRIGERATION EQUIPMENT 75 70 to 76 /' 65 t7o5 82 R.H.% 40 30 to 45 30 to 50 47 Process Temp. F RUBBER DIPPED GOODS R.H. % Storage prior to manufacture................................... Laboratory (ASTM Standard)........................... --____ ___________________________________ _______ 90 80 75-90 60-75 73.4 25-30 25-30 40-50 50 Solvents used in manufacturing processes are usually explosive and toxic, requiring positive ventilation. Volume manufacturers usually install a solvent recovery aystorn. Industrial Air Conditioning 969 ' Table 1. Temperatures and Humidities Applicable to Industrial Air Conditioning--(Continued) Process Temp. F R.H. % TEXTILES Cotton : Opening...... Picking... ............ . Carding, Winter... ' Carding, Summer! Carding, Summer.........................................................or Carding, Summer.........................................................or Drawing...................................... Roving..................................... Ring Spinning Conventional........................... Long Draft.............................. -Frame Spinning......................... Spooling & Warping................... Weaving....................................... Cloth Room................................ - Combing...................................... Linen: Carding.............................. Spinning...................................... Weaving....................................... Woolens: Pickers................ ....... Carding........................................ Spinning...................................... Dressing....................................... Weaving Light goods.............................. Overcoating (32 oz.)................ Drawing....................................... Worsteds: Carding......................... Combing...................................... Gfiling......................................... Top Storage................................ Drawing...................................... Cap Spinning.............................. Spooling & Winding................... Weaving....................................... Finishing..................................... Silk: Preparatory........................... Weaving....................................... Dressing................................ ..... Spinning...................................... Throwing..................................... Rayon: Spinning........................... Throwing..................................... Weaving Regenerated............................. Acetate..................................... Spun rayon.............................. Picking........................................ Carding, roving, drawing.......... Knitting Viscose or cuprammonium... Acetate.................................... Laboratory (ASTM).................. Rayon synthetio fiber processing: Viscose Preparatory............................. Weaving................................... Celanese........................:............. Preparatory............................. Weaving................................... Nylon Preparatory............................. Weaving................................... 70-76 75 75-80 83 85 87 80 80 80-85 80-85 80-85 78-80 78-80 75 75 75-80 75-80. 80 80-85 80-85 80-85 75-80 80-85 80-85 75 80-85 80-85 . 80-85 ' 70-85 80-85 80-85 75 80 75 80 80 80 80 80 80-90 80 80 80 80 75-80 80-90 80-85 80-85 70 80 80 80 80 80 80 55-80 56-60 55 90 80 70 60 60 70 55 55-60 65 70-85 65-70 50-65 60 60 80 60 65-70 50-60 60 60 60-65 50-60 65 65-70 65-70 75-80 65 50-55 65-70 55-70 60 60-65 60-70 60-65 65-70 60 50-60 55-60 50-65 55-60 80 50-60 50-60 65 60 65 60 60 70 70*75 50-60 50-60 Cotton: Relative humidity maintained in ring spinning depends on staple, twist and .whether leather aprons are used for conveying long draft stock. Aprons readily absorb moisture causing cotton to stick when relative humidity is above 55 percent. With conventional 3 or 4 roll spinning, relative humidity may be as high as 70 percent dependent upon draft, twist and staple. . Relative humidity carried in cotton weaving depends upon construction of the doth. When automatic machines are to be tended and the warps are heavily sised, it may be as high as 90 percent. Woolen: In woolen spuming, the relative humidity maintained for mules is generally 55 percent, with conditions over frame spinning at 55 to 60 percent. Both types of spinning depend on the class of stock spun, also the regain in the roving.