Document bN4krwm8YxjVENpLkrxLE1ZZ

PLAINTIFF'S EXHIBIT J-M THERM 0-12* asbestos-free pipe and block insulation DESCRIPTION: A molded, high temperature pipe and block insulation, J-M Thermo-12 is com posed of hydrous calcium silicate. It is an insulating material which, because of its light weight, low thermal conductivity, great structural strength and insolubility in water, is ideal for high temperature piping and equipment. AVAILABLE FORMS: Thermo-12 is fur nished in both sectional pipe insulation and block form. The pipe insulation comes in a complete selec tion of sizes up to 24" x 4" half sections. Pipe sizes 25" through 33" are available in quad segments. Scored blocks 12" x 36" in thicknesses from 1W to 3Vi" are available for application on curved sur faces representing a diameter range from 34" through 180". Scored blocks are furnished with three equally spaced scores. Beveled blocks are also available in widths of 6", 12", and 18", by 36" lengths, in a full range of thicknesses. USES: Especially recommended for use in the power generation and process industries on in door and outdoor piping and equipment operating at temperatures to 1500F. Thermo-12 is light enough for easy handling and fast application. Re peated wettings have no permanent effect on it which makes it ideal for installations subjected to weather, or for insulating underground steam lines. Because it will not burn or carry flame, it may also be advantageously specified for use in the presence of inflammable gases and liquids. J-M Trademark ADVANTAGES: Exceptional Strength Similar in chemistry and composition to a very fine concrete, Thermo-12 will withstand unusual operating abuse without appreciable damage. Extreme Lightness Thermo-12 is as light as many insulating materials pos sessing a fraction of its strength and durability. Not Damaged by Water Can be soaked in water without damage. After drying, conductivity will be as good as new. Easy Application Thermo-12 is purposely made in large blocks and half sections to facilitate handling and reduce number of joints. Low Conductivity LAM 005098 Thermo-12 offers one of the lowest k factors of all in sulations in general use throughout the power genera tion and process industries. Low Chloride Content Thermo-12 has a low chloride content and can be used on Austenitic stainless steel without problems since it meets MIL-I-24244 Amendment 3 for chloride content. DPMC-02711 5 - '1 ) THERMO-12 PIPE & BLOCK INSULATION t Specification Data* ........... yPhiYSICAL PROPERTIES j*V*sfffvWy W ^ -p-v ' ;:H^i^^R^Al-^NDUCTIVrrV 'f4` ` h r. -, >jj ; ,r.:-v1 ^ *r-?-5ji: - >. '. ? *' - c Density (dry) 13 lbs per cu ft Transverse Strength (modulus of rupture) SO psi Compressive Strength (based on 2" thickness of block) 165 psi to produce 5% compression Linear Shrinkage 1.1 % after 24-hr soaking period at 1500F Maximum Service Temperature 1500F The physical properties of Johns-Manville Thermo-12 represent typical average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations. They are supplied as a technical service and are subject to change without notice. Check the Johns-Manville district office to assure current information. MEAN TEMPERATURE, F 100 200 300 400 500 600 700 ~) COMPLIANCE WITH GOVERNMENTSPECS ';7 ' StS'Gomplsancewith ' Pipe Insulation: MIL-1-2781 Grade I, Class b, to 600F (except k at 200F) Grade II, Class d, to 750F (except k at 200F) Grade III, Class e, Type I and II, to 1200F HH-l-523 Type II, Class A and B, to 1200F MIL-l-24244, Amendment 3 Block Insulation: MIL-l-2819 Class 1, to GOOF (except k at 200F) Class 2, to 1200F Class 3, to 1500F HH-l-523 Type I, to 1200F Pipe and Block Insulation: C533, to 1200F !iSI Johns-Manville Greenwood Plaza Denver, Colorado 80217 Sales Offices in Principal Cities LAM 005099 DPMC-02712 I i*hn i*> ||<5A