Document bB4XZLybdB326eqvrmNLjjbQD

IMtiRIRt SMCIMCATIBI - MATIBIAtf , MATC*IAL NAME MATCRIAL NO .- GASKET - ASBESTOS FIBERS & ELASTOMERIC POLYMERS bCT 2-15-73 RELEASED PCR 970023 tMOM AMR SHCCT MO PM CM r* ml f *' T 1 rUl R. D. CHAPMAN or 2 1. SCOPEt THE MATERIAL DEFINED BY THIS SPECIFICATION IS A GASKET MATERIAL COMPOUND ED FROM ASBESTOS FIBERS AND ELASTOMERIC POLYMERS. IT IS PRODUCED BY THE BEATER ADDITION PROCESS. 2. APPLICATION: THIS MATERIAL IS GENERALLY USED AS REAR AXLE COVER PLATE GASKETS. 3. REQUIREMENTS; (FOR 1/32" THICK MATERIAL) 3.1 CONDITIONING: SPECIMENS SHALL BE CONDITIONED IN AN OVEN AT 215 + 5 F FOR 1 HOUR AND COOLED IN A DESICCATOR CONTAINING ANHYDROUS CALCIUM CHLO RIDE PRIOR TO TESTING. 3.2 COMPRESSIBILITYs (ASTM F36, PROCEDURE "A") 15 - 25% 3.2.1 RECOVERY! 40% MINIMUM 3.3 TENSILE STRENGTH: (ASTM F104, TYPE 1) 1500 PSI MINIMUM 3.4 IMMERSION IN LIQUIDS; (THICKNESS CHANGE SHALL BE MEASURED WITH 9 + 0.1 OZ LOAD ON GAGE BEFORE IMMERSION, AND 3 + 0.1 OZ AFTER IMMERSION, USING A PRESSER FOOT DIAMETER OF 0.25 + 0.01"). LIQUID ASTM OIL #1 ASTM OIL #3 ASTM FUEL "A" ASTM FUEL "B" TIME & TEMPERATURE 5 HRS 0 300 i 5 F n" 5 HRS 9 72 + 5 F 11 THICKNESS CHANGE 20 - 355^ 35 - 60% 15 - 30% 25 - 40% 3.5 COMPRESSION SET: 60% MAXIMUM (ASTM D395, METHOD "B", 22 HOURS AT 158 + 2 F, PLIED TO ") 3.6 PHYSICAL AND/OR PERFORMANCE REQUIREMENTS OF FINISHED PRODUCT: WHEN REQUIRED, SHALL BE AS SPECIFIED ON THE AFFECTED PART OR PRODUCT ENGINEER ING DRAWING, OR IN THE AFFECTED PART OR PRODUCT ENGINEERING PERFORMANCE SPECIFICATION. g o 00 \A "O o _________________________ I_________ PRODUCED BY FORD SCF-FORD-0986 IIMliKII IHCATItl - MATKIIAll \.TCWIAL KAMI MATERIAL NO 5V/~M8<H2S-\GASKET - ASBESTOS FIBERS & ELASTOMERIC POLYMERS AT* LIT. INCH A*** tMCCt NO 2t.15-.73,.. RELEASED PCR 970053 AAAAOVID IV R. D. CHAPMAN 3.7 SUPPLIER'S RESPONSIBILITY: ALL MATERIAL SUPPLIED TO THIS SPECIFICA TION SHALL BE EQUIVALENT IN ALL CHARACTERISTICS TO THE MATERIAL UPON WHICH APPROVAL WAS ORIGINALLY GRANTED AND SHALL 3E SUITABLE FOR THE IN TENDED APPLICATION. NO CHANGES IN AN APPROVED FORMULATION, NOR AN APPROVED PROCESS BY WHICH APPROVED SAMPLES WERE MANUFACTURED, SHALL BE MADE UNTIL NEW SAMPLES HAVE BEEN TESTED AND APPROVED, AS OUTLINED IN PARAGRAPH 4. k. APPROVAL OF NEW SUPPLIERS: MATERIALS SUBMITTED BY NEW SUPPLIERS TO THIS SPECIFI CATION SHALL BE APPROVED BY THE AFFECTED PRODUCT ENGINEERING OFFICES. FOR APPROVED SOURCES, SEE ENGINEERING RELEASE AND/OR ENGINEERING STAFF'S APPROVED SOURCE LIST. 00 o o o 00 ___________________________________________ I________________ Eft "A >5 IMtKM im. ^Br^i^pioT^CTn/tany-, PRODUCED BY FORD