Document ZB0am04LwEev5ZBVVqwK6Ge3V

204 CHAPTER 10 1954 Guide ; 'A* and partly an operating problem. It is accomplished by reducing the interior dew-point temperature or by raising the surface temperatures that ~ are below the dew-point, or both. The dew-point temperature may be lowered by giving attention to the sources of the moisture, and in winter, .> may be controlled by ventilation, or possibly by some moisture absorption ; process. The temperatures of the inside room surfaces in winter may be <; increased by adding insulation to outside walls, by double glazing of win dows, by circulating warm air over the surface, or perhaps by direct heating ; of the surface. The most expedient method of overcoming a surface con- 1 densation difficulty will depend upon special conditions surrounding the ' problem. VAPOR TRANSMISSION THROUGH MATERIALS The condensation of moisture within buildings is not limited to visible surfaces. Vapor permeates through certain materials very readily and : may penetrate exterior or cold walls and contact material therein having a i temperature below the dew point of the vapor. At these places the vapor - will condense to form liquid water or frost. Such concealed condensation may, if excessive, cause serious damage which is particularly insidious when it continues without detection. An accumulation of hidden condensation ^ often causes great difficulty in long-range processes. ' The principal mechanism by which water vapor passes through solid '- materials is a process of diffusion, the net transfer requiring a difference of vapor pressure. Various writers have suggested the possibility that ) adsorbed moisture (which is neither vapor nor liquid) moves from a region of high concentration to one of lower concentration without the benefit of-a vapor pressure difference, but this action has not been conclusively)I demonstrated and probably is negligible in the problems here considered.)'; The property of a material which enables it to transmit vapor is known as ;, its vapor permeability. Other forces which play an important part are; capillarity and gravity (when the vapor changes to liquid at any point in;' its path), and the hygroscopic adsorption of moisture (which, for many, materials, is nearly proportional to relative humidity). Hi The term permeability has frequently been applied to the rate of vapor.) transmission for the thickness of the material considered or tested, butthis use is not consistent with the use of conductivity (thermal) which relates) to a property of the material based on unit thickness. It has been sug-;gested2 that the term permeance (similar to conductance in heat transfer))! be used when referring to any specimen of definite thickness, or an ai\4 sembly of such pieces. This recommendation is followed in this chapter.)) The term permeability, as used herein, defines a property of the material.; and is numerically equal to the permeance of a unit thickness. The theory covering water vapor transmission through materials leads) to the following formula, 1' W = MAT Ap 0)- mW; where, W = - total weight of vapor transmitted through the specimen, grains. A = area of the specimen, square feet. T = time during which the transmission occurred, hours. Ap = = the difference of the vapor pressure across the specimen, inches of mercury/-: M -- = the permeance of the specimen, in perns, or grains per (square foot) (hour)- (inch of mercury vapor pressure difference). Water Vapor and Condensation in Building Construction 205 The basic units in Equation 1 are favored by the building industry. The designation perm for the unit of permeance has been proposed2 as a convenient substitute for the unit, 1 grain per (square foot) (hour) (inch of mercury vapor pressure difference), and this recommendation is followed herein. The weight of vapor transmitted is unquestionably proportional to aTea and time, but is not always proportional to the vapor pressure difference. Proportionality is a useful relation when applied with caution in a limited range, but the expression per inch of mercury does not sanction an un- . restricted extension of this relation. In other words, the permeance of a specimen is not a constant under every condition. This fact must be con sidered but is generally not !an obstacle in the solution , of many practical problems: Vapor resistance is the reciprocal of permeance, and theory indicates that the vapor resistance of a homogeneous specimen is proportional to its thickness. Permeance, therefore, is inversely proportional to thickness, and: where, M=t t or, ii -- Mt (2) M = the permeance of the specimen, perms. t = the thickness of the specimen, inches. As defined by Equation 2, n is the permeability of the material or the permeance per unit thickness. Using consistent units, permeability is expressed in perm-inches, a perm-inch being equal to one grain per (square foot) (hour) (inch of mercury per inch of thickness.) Equations 1 and 2 may be combined to give: W = plAT? (3) where, e = the average permeability of the material. (The spot permeability in thin ele ments may be progressively different throughout the thickness.) The overall vapor resistance of an assembly (like a wall) of materials in series is the sum of the resistances of its component parts provided con densation does not take place within the assembly. Expressed in the njore usual terms, the permeances (Mi, Mi, M3, etc.) of the individual pieces may be combined by use of the formula M= -- +-- + -- + - -- Ml Mt Mt Mb (4) Equation 4 holds for materials that are reasonably homogeneous and in a wmdition of steady state where the transmission at all points is a vapor diffusion process as, for example, in a vapor transmission test. Actually, the conditions of moisture movement through a building wall are generally different. A steady state, where the entering and leaving moisture are rarely exists, and frequently, the moisture in some portion of the Path is liquid, in which case forces of capillarity and gravity are usually