Document Z6m78dZdXJKbOQVpMox8nr4L

200 CHAPTER 9 1952 Guide may be controlled by ventilation, or possibly by some moisture absorption process! The temperatures of the inside room surfaces in winter may be .increased by adding insulation to outside walls, by, double glazing of win dows, by circulating warm-air over the surface, or-perhaps by direct heating of the surface. . The most expedient method of overcoming a surface con densation difficulty will depend upon special conditions surrounding the problem. Vapor Transmission through Materials ' The condensation of moisture within buildings is not limited to visible surfaces. Vapor permeates through certain materials very readily and may penetrate exterior or cold walls and contact material therein having a temperature below the dew point of the vapor. At these places the vapor will condense, to form liquid water or frost. Such concealed condensation may, if excessive, cause serious damage which is particularly insidious when Fig. 6. Relative Humiditt at Which Visible Condensation Will Appeab on Inside Stxhpace it continues without detection. An accumulation of hidden condensation often causes great difficulty in long-range processes. The principal mechanism by which water vapor passes through solid - materials is a process of diffusion, the net transfer requiring a difference of vapor pressure. Various writers have suggested the possibility that adsorbed moisture (which is neither vapor nor liquid) moves from a region of high concentration to one of lower concentration without the benefit of a vapor pressure difference, but this action has not been conclusively demonstrated and probably is negligible in the problems here considered. The property of a material which enables it to transmit vapor is known as its vapor permeability. Other forces which play an important part are capillarity and gravity (when the vapor changes to liquid at any point in its path), and the hygroscopic adsorption of moisture (which, for many materials, is nearly proportional to relative humidity). The term permeability has frequently been applied to the rate of vapor transmission for the thickness of the material considered or tested, but this use is not consistent with the use of conductivity (thermal) which relates. . to a property of the material based on unit thickness. It has been sug gested17 that the term permeance (similar to conductance in heat transfer) ' Heat Transmission Coefficients of Building Materials 201 be. used whep referring to, any. specimen of definite' thickness, or an as sembly of, such pieces. This recommendation'is followed in this chapter. The -term; permeability, as used herein, defines a property of, the, material and is numerically equal to the permeance of. a unit thiokness. The theory covering water vapor transmission through materials leads to the following formula, W = MAT Ap (7) where, W = .total weight 'of vapor transmitted through, the specimen, grains. A =. area of the specimen, square feet. . , T. = .time during which the. transmission occurred, hours. .; Ap -- the difference of the vapor pressure across the specimen, inches of mercury, M = the permeance of the specimen, in perms, or grains per (square foot) (hour) (inch of mercury vapor pressure difference)... The basic units in Equation 7 are favored by the building industry. The designation perm, for the unit of permeance has been proposed17 as a convenient substitute for the unit,T grain per ^square foot) (hour) (inch of mercury vapor pressure difference), and this recommendation is followed herein. :. j The weight ofvapor transmitted is unquestionably proportional to area and time, but is not always proportional to the vapor pressure difference. Proportionality is a useful relation when applied with caution in a limited range, but the expression per'inch of mercury does not sanction an un restricted extension of this-relation.. In other .words, the permeance of a specimen is not a constant-under every condition. This factmust be con sidered but is generally not an obstacle in the solution of many practical problems. Vapor resistance is the reciprocal of permeance, and theory indicates that the vapor resistance of a homogeneous specimen is proportional to its thickness. Permeance, therefore; is inversely proportional to thickness, and: where, or, it = Mt (8) M = the permeance of'the specimen, perms, t = the thickness of the specimen, inches. Evidently p is the permeance of a unit thickness of the material, wliich is its permeability,' as above defined. Using consistent units, permeability is expressed in perm-inches, a perm-inch being equal, to one grain per (square foot) (hour) (inch of mercury per inch of thicknete.) ' Equations 7 and 8may be combined to give: "` . where, w= ' (9) M = the average permeability of the material. (The spot permeability in thin ele- , nients may be progressively different throughout the thickness.) The overall vapor resistance of an assembly (like a wall) of materials in