Document VJNeQ3rJZ8orEv3Z16j5vX6Vw

MATERIAL SAFETY DATA SHEET FOR COATINGS, RESINS AND RELATED MATERIALS (Approved by U S Department of LfPOr Essentially Similar to F orm OSHA-20) NPCA V BY: P. Jazenskl Section I manufacturers name street address DAYTON CHEMICALS DIVISION WHITTAKER CORPORATION 10 Electric Street city.state.andzipcode West Alexandria, Ohio 45381 EMERGENCYTELEPHONE NO information telephone no 513-839-4612 Same product class Solvent-borne Bonding Agent tradename THIXON GPO manufacturers code identification DOT CLASS: Adhesives - Flammable Liquid UN #1133 ------------ ----------- " INGREDIENT Section II - HAZARDOUS INGREDIENTS PERCENT Wet. tlv *STEL PPM mo/M1 LEL Xylene Proprietary Curative System Carbon Black Non-Water Soluble Lead Compound (as lead) ,1,1-Trichloroethane < 50 <6 <4 <4 < 26 100 Unknown -- 350 |a r 1.0 ---- 3.5 -- *0.45 lead fume or dus t 1900 8.0 VAPOR PRESSURE 9.5 -- -- 100 boiling range Boiling Temperature: Section III - PHYSICAL DATA > 200F- vapor density GD HEAVIER, LIGHTER.THAN AIR EVAPORATION RATE miFASTER SLOWER THAN ETHER PERCENT VOLATILE by wgt. 75 WEIGHT PER gallon 8.94 lbs. ________________________ Section IV - FIRE AND EXPLOSION HAZARD DATA flammability classification Flammable Liquid flashpoint 77f (25C) lel 1.0 extinguishing media C02, dry chemical or alcohol type foam. _,D 0871 4? C0NFTD8NTtai unusual fire and explosion hazards Considered serious fire hazard due to low flash point, high volatility and heavy vapor. SPECIAL FIRE FIGHTING PROCEDURES Closed or confined quarters require self-contained breathing apparatus. _____________________________ Section V - HEALTH HAZARD DATA______________ threshold limit value See Section II EFFECTS OF OVEREXPOSURE ACIJTE Irritation of eyes and nasal passages and corneal edema. Headache, nausea and serious narcosis may develop. CHRONIC EMERGENCY ANO FIRST AID PROCEDURES Remove excessively contaminated clothing and wash skin with soap and water. Irrigate eyes thoroughly with water. Remove to uncontaminated atmosphere and give artificial respiration and oxygen if necessary. If swallowed, do not induce vomiting, but contact physician immediately. Section VI - REACTIVITY DATA stability | | unstable [ y | stable INCOMPATABIL'TY [Materials ro evo/01 hazardous decomposition products None known conditions to avoid None known HAZARDOUS POLYMERIZATION CONDITIONS TO AVOID may occur D WILL NOT OCCUR Section VII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELE ASE D OR SPILLED waste disposal method Eliminate all ignition sources. Absorb with rags and/or vermiculite and discard in closed containers. Incineration RESPIRATORY PROTECTION Section VIII - SPECIAL PROTECTION INFORMATION Self-contained breathing apparatus or industrial canister type gas masks. ventilation Local exhaust preferable. protective gloves - Rubber eye protection - Safety goggles other protective equipment DO 0871.43 CONFTDFNTTAl Section IX - SPECIAL PRECAUTIONS PRECAUTIONSTO BE TAKEN IN HANDLING AND STORING dol storage category other precautions Flammable Materials Area _ _ ,, Store in cool area away from open flames, sparks and other ignition sources. Keep containers tightly sealed. CONTACT WITH ALUMINUM PARTS IN A PRESSURIZABLE FLUID SYSTEM MAY CAUSE VIOLENT REACTION. Consult equipment supplier for further information. Do not take internally. Avoid prolor or repeated contact with skin. Always ground container when pouring to avoid static dis charge (sparking) which could ignite solvents. Do not allow free-fall of more than a few inches when pouring, as dangerous static charges could be generated. Avoid prolonged or repeated breathing of solvent vapors of concentrations above TLV.