Document V3oYgYoko298nE1GR5VgGeng8
/
MOLDING COMPOUNDS
PHENOLIC
MATERIAL SAFETY DATA
SHEET
\
MATERIAL SAFETY DATA SHEET
(APPROVED BY U.S. DEPARTMENT Of LABOR "ESSE NT1ALL* SIMILAR" TO FORM LSBCOS-fl
i/80
MANUFACTURER'S NAME
REICHHOLD CHEMICALS, INC.
Section I
STREET ADDRESS
525 North Broadway
CITY, STATE AMD ZIP CODE
White Plains, New York 10603
fMnMMCvmimacNo. 914.682_5700
---
CHEMICAL NAME A^D SYNONYMS
Phenolic Molding Compound
CHM,cKBF*-11.yphenol/Formaldehyde
trade HM.E pj,enoiic Molding Compound "" Uos. 25-310,25-346,25-347,25-388
25-39B,2^-397^25=506___ "rnlnrt -_______
; Section 1 -HAZARDOUS INGREDIENTS
| PAINTS. PRESERVATIVES. & SOLVENTS |
PIGMENTS
%
TLV
SOLVENTS
TLV %
NOT
A > p LIC ABLE
CATALYST
NOT
ADDITIVES
A > P LIC ABLE
VEHICLE
OTHERS
NOT
A : > P LIC ABLE
HAZARDOUS MIXTURES OF OTHER LIQUIDS, SOLIDS, OR GASES
1%
TLV (Unit*)
This compound may contain up to 51% bv weiqht.bound asbestos fibers. While it would not be expected that under normal handling and use of
this compound free --such-a5~aniiing,
asbestos fibers would be released, subsequent procei sanding, mining'ana filing May release asbestos fibi
isin frsl
a____
Refer to Section Asbestos 1910.1001 of the Occupational Safety & Healti i e si--
Section III-tPHYSICAL DATA
.|
BOILING POKT (*F4 VAPOR PRESSURE (rmn Mg.) VAPOR DENSITY (AJR-t) SOLUBILITY IN WATER APPEARANCE AND ODOR
None Nil Mil
SPECIFIC GRAVITY
(%)PERCENT VOLATILE
BY VOLUME EVAPORATION RATE
I................ -D
Nil
Granular soli d. Odor is nil
Nil Nil
Section IV-FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used) Wot Applicable
fummmu um.tb
|--------w--------1------- w--------
EXTINGUISHING MEDIA
. __
Water, C0^r chemical foam
SPECIAL FIRE FIGHTING PROCEDURES
Wear self-contained breathinq apparatus if fiahtinq fire in a confined area.
such as a warehouse.
UNUSUAL FIRE AfjO EXPLOSION HAZARDS
Dust/air mixtures are explosive.
THIS WfORMATJOW IS FURNISHED WJTMOOT WARRANTY. REPRESENTATION, INDUCEMENT OR LICENSE Of ANY KINO, EXCEPT THAT IT W ACCURATE TOTMEBCSTOFREtCKHOU) CHEMICALS, INC.'S KNOWLEDGE. OR OSTAtMEO FROM SOURCES SELttVtD BY REICHHOLD CHEMICALS, INC, TO KJUXURATtJJJD KISHHOLD| CHEMICALS, INC. DOCS NOT ASSUME ANY LEGAL RESPONSIBILITY FOR USE OR RELIANCE UPON SAME. CUSTOMERS ARE ENCOURAGED TO CO*UCT THEIR OWM| TESTS. BEFORE USING ANY PBOOUCT. READ ITS LABEL.
A 71 EXHIBIT
Vl
0000004
Deponent (X(Wof)
Pcxte^JglL^iDtr
WWW.DEPOBOOk.com
( MATERIAL
MOLDING COMPOUNDS SAFETY DATA
PHENOLIC V) SHEET
STABILITY
UNSTABLE
Section VI-REACTIVITY DATA
CONDmOKS TO AVOID
I INCOMPATIBILITY i
STABLE
X
lo mntd)
None known.
HAZARDOUS DECOMPOSITION PttOOUCTS
Carbon dioxide. carbon monoxide,
- ______________
phenol
(s) , ammonia -
KAIAROOUS POLYMERIZATION
MAY OCCUR WIU. NOT OCCUR
CONDITIONS TO AVOID
None known X
Section VII --SPILL OR LEAK PROCEDURES
*Ttea TO K TMCSH l CAM UATERUU. IS REUEUED OH BtUED . Vacuum or sweep up. Use sweeping compound to avoid generating dust.
Ventilate area well. Wear respirator if dust is generated,
*
f
1 n
Waste Disposal Method 1. Incinerate.________________________________________________________________________
. 2. _Laad_.fill in accordance with State and Federal regulations
Section VIII-SPECIAL PROTECTION INFORMATION
P8^T8T%S^?glii'^*^SatS&^S!^ture extremes and moisture. Both affect product
performance. Do not breath heated vapors from molding process.
onnntEcumoia
...
----
0000005
V