Document Rvba5KLdVgD07Z9YgMLLYNyv

FSOM GEORGE H* FARRAH ENVIRCNMENTAL HEALTH LABORATORY ALCOA TECHNICAL CENTER INDUSTRIAL HYGIENISTS / April 17, 1972 RE: INDUSTRIAL HYGIENE NEWSLETTER - ASBESTOS DUST EXPOSURES Mr. R. P Carter's Newsletter dated December 23, 1971, concerning the 06HA emergency standard for asbestos has led to many requests for advice in determining compliance with the new Federal standards. This letter attempts to point out the more likely areas of exposure to asbestos dust, general reduction of worker exposures and includes sampling and analytical methods to determine if you are in compliance with any promulgated OSHA standard referring to asbestos. The principal asbestos-containing materials of concern (apart from building insulation and pipe covering) are Molten Metal Marinite (Johns-Manville), asbestos shorts and insulating block used in smelting cells and furnaces of all types. Marinite constitutes a problem from the point of delivery of sheet stock, through storage and handling, all machining operations, removal of used material, to disposal of wastes. Asbestos shorts, as currently used, may present dust problems during transfer and mixing of the dry material in preparation of mortar, and in removal of old linings. According to Mr. H.M. Short, practically all the insulating (back-up) block used in smelting cells and in all types of furnaces contains 8% asbestos. This means that the operations of removing old lining from furnaces and cells, and even the relining, can create asbestos dust exposures. Asbestos is also used in other forms, such as paper and rope, and in a variety of applications - but principally as high temperature gasket. Wherever asbestos is routinely used, and in whatever form, we must take a careful look at exposures, not only of those handling the material, but of other workers in the ^vicinity. As mentioned in the December 23 Newsletter, this concern applies as well to the demolition of asbestos-covered structures, pipes, etc. In starting an asbestos dust control program, the first step should be the listing of all forms and applications of asbestos-containing materials. This information should be readily available from the Process Materials List which all plants should have prepared and which they should maintain as current information. Next, all operations involving asbestos should be critically inspected. In many cases, it will not be necessary to collect samples and count fibers to recognize that concentrations are too high. If inspection of the operation shows a visible dust cloud, or if there is a layer of asbestos dust on surrounding surfaces, control measures must be instituted at once. Many of these measures are specified in the Federal Register of Tuesday, December 7, 1971; there are also some useful suggestions in the copies of Insulation Hygiene Progress Reports which were attached to the December 23, 1971, letter. Most shops in which Marinite is processed have exhaust ducts attached to lathes, table and bandsaws, routing machines, etc. Power hand tools are similarly equipped and connected to the exhaust system. Some, of these do a fairly good job of capturing dust, others are of little value. To be effective, enclosures must be virtually complete, with 412259 0191 Industrial Hygienists April 17, 1972 Page 2 high capacity exhaust systems. Furthermore, exhaust systems must be connected to collection systems which meet the performance standards set forth in the Ftederal Register, December 7, 1971, page 23208, Section 1910.93a and pages 23242-23243, Sections 61.23 and 61.24. There should be no visible emissions from discharge of the collection system. This discharge should be to the outside and directed away from any windows that may be opened, to avoid any pos sibility of dust being blown back into the workroom. Where the * collector clischarge is directed against the side of a'building and has resulted in a readily visible brown deposit, collection efficiency may well be questioned. Assistance with your control problems can be obtained from the Pittsburgh Environmental Engineering Division. The handling of dry asbestos shorts may be avoided by purchase of this material in plastic bags equipped, with h^se connections which permit wetting of the contents before the bag is opened. Wet-digging of old trough and furnace linings, where this is permissible, will reduce the generation of dust. If wet removal and replacement of lining is done in the open, provision should be made for adequate clean-up, including flushing away of fines, so that dust will not blow about as the work area dries. In all cases, clean-up must be done by means of vacuum cleaners and not by dry sweeping. Asbestos wastes should be collected and disposed of in sealed bags an required by the existing standard. In removing old furnace and cell linings, wetting the exposed surfaces to minimize dust should be employed wherever practical. Again, the Pittsburgh Environmental Engineering Division should be consulted on the practicality of exhaust from the working area, especially during lining removal. After installation of all appropriate control measures, even though there is no visible dust, an air sampling program will be necessary to determine whether respiratory protection may be discontinued. If levels of dust are above the standard permitted, the actual levels will establish the type of respiratory protection required. The emergency standard for anbestos dust published in the Federal Register of December 7, 1971, established the approved method for counting the fibers in a sample. When this level was proposed as a permanent standard in the Federal Register of January 12, 1972, (Attachment #1) some of the details of sampling were also spelled out, along with requirements for warning signs, environmental sampling, and medical examinations. Early in February, NIOSH published a criteria document on asbestos dust recommending a still lower fiber count as the standard. The detailed method for sampling, counting and calculating the fiber concentrations which was contained in this document is given in Attachment #2. Attachment #3 is a copy of Q3HA Sampling Data Sheet #2 which contains additional helpful information. Regardless of the concentration which is established as the final standard, these sampling and analytical procedures will apply. 412259 0192 Industrial Hygienists April 17, 1972 Page 3 Sampling to determine worker exposures will be the responsibility of each plant and suitable equipment must be purchased, if it is not already available. The decision to evaluate samples in-house or to send them to a commercial laboratory will depend upon availability of personnel and equipment, and the volume of work anticipated. While our Environmental Health Laboratory will be equipped to make these evaluations for the Technical Center, the anticipated demand would be too great if we were to offer our services, company-wide. Collection of samples is most conveniently done with pre-loaded filters and a small, battery powered pump of about 2 liters per minute capacity, such as the following* .. Pre-loaded Filters Millipore Field Monitors, Cat. No. MAWP 037 AO Price per carton of 50 (available from Millipore Corp., Bedford, Mass. 01730) $30.00 Battery Powered Pump 1. MSA Portable Pump Assembly, Model G, Cat. No. 456058 (Requires MSA Battery Charger Assembly, Model G Pump, Cat. No. 456059) $160.00 $ 40.00 Mine Safety Appliances Co. 201 North Braddock Avenue Pittsburgh, Pa. 15208 or 2. NEI Micronair Personal Air Sampler, Cat. No. 3900-10, complete with Nicad battery and charger $195.00 National Environmental Instruments, Inc. 1865 Post Road Warwick, R.I. 02888 Counting the fibers collected on the filters requires the use of a microscope equipped for phase contrast illumination, and a good quality microscope lamp, preferably one capable of providing Ktihler illumina tion. To adape a given microscope for this work, the manufacturer should be consulted because the optical parts of different manufacturers may not be interchangeable. A Bausch and Lomb CTA-10 conventional microscope would require these accessories: special condenser, telescope, filters, phase annulus, and objective totaling $344.00. A suitable microscope lamp may cost about $100.00. If a microscope is to be purchased especially for this work, consideration should be given to the American Optical N51MP Series 50 Phase Teaching Microscope with 4X scanning objective, 10X phase and 45X phase objectives, and built-in 412259 0193 Industrial Hygienists April 17, 1972 Page 4 illuminator. It appears to be a satisfactory instrument and sells for $448.00, without carrying case. Examination of Molten Metal Marinite dust by phase contrast and bv bright field illumination showed little difference since the fibers are stained brown - probably by iron oxide - due to heat treatment vdiich Marinite receives to convert it to the Molten Metal type. This was confirmed by discussion with the Product Manager for Marinite, Johns-Manvilie Corporation, who stated that the only type of asbestos used din Molten Metal Marinite is the brownish amosite. At this time, it appears that exposures to Molten Metal Max inite fibers can be evaluated by bright field counting with a conventional microscope. Therefore, this can be used to get preliminary data on Marinite dust concentrations, until equipment for the standard method required by OSHA is obtained. This is not the case for other forms of asbestos, which will require phase contrast microscopy at the outset. Sending samples to commercial laboratories for counting may be advantageous in some cases, but may also present difficulties in locating laboratories qualified to perform this service. Walter C. McCrone Associates, Inc., Chicago, 111., is probably the best known organization in the field of consultative microscopy and is preparing to offer this service at a change of $25.00 to $30.00 per sample. Mr. Robert P. Carter has supplied a corrected list for the respirators approved by the Bureau of Mines to replace that attached to his December 23, 1971, letter re "Emergency Standard for Exposure to Asbestos Dust." A copy of this corrected list is Attachment #4. If after reviewing this letter and all attached materials you have questions or special problems concerning methods of sampling and counting, please contact me. GEORGE H. FARRAH GHFrmh Attachments cc, no att: Chairmen, Environmental Health Steering Committees Vjs W. Rieke, Pgh. - 2 yC. V. Cralley/T. B. Bonney, Pgh. - 7 W. B. Garyotis, Pgh. - 2 R. H. Watson, Pgh. - 7 R. B. Kempton, Rea Magnet 412259 0194 DISTRIBUTION Arkansas Badin Chillicothe Cleveland Cressona Corona Davenport Lafayette Lancaster Lebanon Logans Ferry Marshall Massena Mobile Pt. Comfort Richmond Rockdale Tennessee Tifton Vancouver Vernon Warrick Wenatchee INDUSTRIAL HYGIENISTS J.L. Laudenberg Earle Morgan J. Schachtele L. L. Grubb E.J. Schafer R.H. Allen K.W. Williams L.S. Chambers H.E. Hillstrom R. Andrew W.D. Helmick J.W, Warnock W.S. Barr Albert Steele C. F, Scott R.E. Beachem A.G. Clayton J.C. Vergho L.L. Haisch H.L. Chandler R.L. Parsons J.A. Thompson EHSC CHAIRMEN J.W. Wells R.C. Hinkle J.J. Thimons L.J. O'Connell N.O. Kraft R.H. Allen D. L. Schaffer J.B. Dolan R.S. Howell R Andrew J. Hicks L.E. Norris R.W. Knapp R.V. Newsome C.L. Green R.H. Cunneen G.W. Hutton H.W. Brooks H.E. Chandler P.F. Woodward J. R . Jones R.J. Knox J.A. Thompson Cap** Z-L-. t'L-l-.C-iO ,~Pf, (t J-A e o, IS -t" 412259 0195 Attachment #1 466 PROPOSED RULE MAKING regulated by this order than from other order plants during the mouth. Proposal No. 9. Amend 11036.43(b) (3> to read "Other source milk In bulk fluid form exclusive at that specified in i 1036.41(e)(6)'. Proposal No. 10. Amend 1 1036.43 /*- terplant movements. Add in (1036.43(0(3) (1). (11). and (hi), the words "of bottling grade milk" after the phrase "constitute regular sources of supply". Proposed by Borden, Inc.: Proposal No. 11. Add to 11036.45 a pro vision to read as follows: Subtract from the remaining pounds at skim milk In Class n, the pounds of ririm milk in other source milk (except that received In the form of a fluid milk product) that Is added to, or used to pro duce, any product specified In 11036.41 (b). proposed by Town and Country Dairy, Garvins Dairy, Sweet Borne Dairy, and TTalms Modem Dairy: Proposal No. 12. Amend order No. 36 to provide that the following counties In the State of Ohio: Belmont, Jefferson, Harrison, Monroe, and part of Guernsey now in the marketing area; plus the West Virginia counties of Hancock, Brooke, Ohio, and Marshall be Included In Zone 1 as defined by the proposal of Milk, Inc. (Proposal No. 1): or alterna tively that the above dairies are to be put In the present Cleveland-Erie District rather than the Pittsburgh District. Proposed by the Dairy Division, Con sumer and Marketing Service: Proposal No. 13. Revise I 1036.11(a) (1) to read as follows: 1036.11 Pool plant. (a) A distributing plant that has: (1) Route disposition except filled milk, during the month of not less than 50 percent (40 percent for each month off April through August) of the total re ceipts of fluid milk products, except filled mfik, that are approved by a duly constituted health authority for fluid consumption and that are physically re ceived at such plant or diverted as pro ducer mfik pursuant to 11036.16 to a supply plant Qualified under paragraph (b) or (c) of this section or a nonpool plant; and * Proposal No. 14. Review the provisions of 1 1036.11(c) to determine whether they should apply only to plants primar ily engaged In the transfer of milk to distributing plants qualified under para graph (a) of this section. Proposal No. 15. Revise i 1036JO (a) (2) to read as follows: S 1036.30 Report of receipt* aid atiEzation. (a) * (2) Inventories at the beginning and end of the month of the following products: (I) Fluid milk products; and (II) Products listed In 11036.41(b) (1), except those received In packaged form from another plant, showing separately such Inventories in bulk form and In packaged form; Proposal No. IS. Revise 11036.41(c) (6) (vll) to read as follows: g 1036.41 flww of utilisation. ((c6)) (vll) Less 1A percent of the quantity of bulk fluid milk products and bulk cream transferred to other plants which does not exceed such quantity to which per centages are applied in subdivisions (1), (11), (lv), (v) and (vl> of this subpara graph; Proposal No. 17. Make whatever changes are necessary In the order to eliminate the possibility of a handler be ing charged under the order at the Class I price for milk that already has beat classified and priced as Class I milk un der a Federal order. Proposal No. IS. Reposition, for clari fication of the order, the provisions which establish that the Class I price for other source milk when adjusted for location of the shipping plant, shall not be less than the Class m price. Proposal No. 19. Make whatever changes are necessary In the order to provide for a uniform "equivalent price" section to read as follows; g 1036.54 Equivalent price. If for any reason a price or pricing component required for this part for computing class prices or for other pur poses Is not available In the manner de scribed in this part, the market admin istrator shall use a price or pricing com ponent determined by the Secretary to be equivalent to the price or pricing com ponent that Is required. Proposal No. 20. Make such changes as may be necessary to make the entire marketing agreement and the order con form with any amendments thereto that may result from this hearing. Copies of this notice of hearing and the order may be procured from the Market Administrator, 7503 Brookpark Road, Cleveland, OH 44129 or from the Hear ing Clerk, Room 112-A, Administration Building, U.6. Department of Agricul ture, Washington, D.C. 20250 or may be there Inspected. Signed at Washington, D.C, on Janu ary 7, 1972. John C. Bluk, Deputy Administrator, Regulatory Programs. [TO Doo. 73-466 Filed l-ll-73;8:48 am] DEPARTMENT OF LABOR Occupational Safety and Health Administration 129 CFR Part 19101 STANDARD FOR EXPOSURE TO ASBESTOS DUST Notice of Proposed Rule Making Section 6(c) of the Williams-Steiger Occupational Safety and Health Act of 1970 (84 Btat. 1596; 29 UJ3.C. 655) pro vides that mxm the publication of an emergency temporary standard In the Federal Racisxxx the Secretary of Labor shall commence a rule making proceed ing In accordance with section 6(b) of the Act, and that the emergency standard as published shall also serve as a proposed rule for the proceeding. An emergency temporary standard concern ing exposure to asbestos dust was pub lished in the Federal Register on De cember 7, 1971 (36 FJL. 23207). Accord ingly, pursuant to section 6 (b) and (c) of the WUllams-Stelger Occupational Safety and Health Act of 1970 (84 StaL 1593, 1596; 29 TJJB.C. 655). 29 CFR 1910.4, and Secretary of Labor's Order No. 12-71 (36 Fit. 8754), tt Is hereby proposed to amend 29 CFR Part 1910 as set forth below. The proposals Include the emergency temporary standard and additional proposed rules on subsidiary Issues. Interested persons are Invited to sub mit, both orally and In writing, data, views, and arguments concerning these proposals. Written data, views, and arguments may be mailed to the Office of Safety and Health Standards, Room 305, 400 First Street NW, Washington. DC 20210, with in 30 days after the publication of this notice In the Federal Register. The data, views, and arguments will be available for public inspection and copying at the Office of Safety and Health Standards, except as to matters the disclosure of which is prohibited by law. Oral data, views, and arguments will be received by Hearing Examiner Arthur Goldberg, at a hearing beginning at 10 am. on March 14, 1972, in Conference Room B. Departmental Auditorium, 14th Street and Constitution Avenue NW, Washington, DC. Persons desiring to ap pear at the hearing must file with the Office of Safety and Health Standards a notice of Intention to appear, no later than March 3, 1972. The notice must state the name and address of the per son to appear, the capacity In which he will appear, and the approximate amount of time required for his presentation. The notice must also Include, or be ac companied by. a statement of the posi tion to be taken with regard to the pro posed rules. The oral proceedings shall be reported verbatim, and transcripts shall be avail able for Inspection to any Interested per son on such conditions as the presiding KDERAL REGISTER. VOL >7, NO. 7--WEDNESDAY, JANUARY 12, 1972 4?2259 0196 PROPOSED RULE MAKING 467 hearing waminw mar prescribe. The hiring examiner shall regulate the SubfftaAC* paragraph are not feasible or do not re Mppcf UsfM* duce the concentration of asbestos dust course ol the oral proceedings, dispose of procedural requests, objections, and Amorphous, iMtadl&f natural distOSUhCOOU* earth, ..... similar matters, regulate the conduct of below toe limits prescribed to paragraph 3D 80mc/M* (a) of tols section, toe employer shall require the use of respiratory protective those present at the hearing b; appro *010. devices. The selection of respiratory pro priate means, and shall exclude to the Silicates (loss than 1% cry* tective devices shall be limited to those extent practicable Irrelevant, immaterial, and unduly repetitious data or argu ments. The hearing examiner shall have discretion to keep the record of the hear ing open for a reasonable, stated time to tallneule*): Ml Soapstone............... . Talc..................................... Portland oemeai........ Graphite (natural).............. Coat dost (respirable fraction X 30 30 30 16 specified to paragraph (c) of this section. <il) The employer shall require that each employee test his respiratory pro tective device before each use in order to insure a proper fit according to the receive written recommendations, and additional data, views, and arguments from any person who has participated hi lest than 0% 610,).. . For more than 9% 8KH. 2.4mg/M* manufacturer's instructions. The em or Knc/M* ployer shall further provide for .effective training or supervision of employees in the oral proceeding. Upon completion of the oral proceedings, the transcript thereof, together with written submis Inert or Nuisance Dost: Respirable fraction_____ Total dust ........................ %8tOr+l the testing of respiratory protective de 16 30 lASmmgs/fMM1I vices for fit before their use. (c) Allowable respirators. (1) When sions on the proposed rules, exhibits filed the 8-hour time-weighted average con during the bearing, and any poethearing data, views, arguments, and recommen dations shall be certified by the hearing Hots: Conversion factor*znppofX3fi4miUion particles per cubic meter particles per aa f Milhous ofpartfcles per cubic foot of air, baaed on centration of asbestos dust is projected to exceed 5 fibers longer toon 5 microns per milliliter, but not to exceed 25 such examiner to the Assistant Secretary of labor for Occupational Safety and Health for his decision. The Assistant Secretary may adopt the proposals with or without changes, or determine not to tmpinger samples counted by Ught-Aeld technics. * Tbe percentage of crystalline silica in the formula Is the amount determined bom air-borne samples, except in those Instances in which other methods havebeen shown to be applicable. i As determined by tbe membrane filter method at 430 X phase contrast magnification. fibers, and when a concentration over a period of 15 minutes exceeds 10 fibers longer than 6 microns per milliliter, but does not exceed 50 such fibers, a re usable or single use filter type respira issue a rule. Under the authority of section 6(b) (1) Both concentration and percent quarts for the application of this Uznit are to be determined from the traction passing a sire-eelector with tbe following tor, operating with negative pressure during the inhalation phase of breath and section 7(b) of the Act, the Assist characteristics: ing. approyed by toe UjS. Bureau of ant Secretary of labor for Occupational Mines under the provisions of 30 CFR Safety and Health will request the recommendations of an advisory com Aerodynamic diameter (unit density sphere) Percent passing selector Fart 14 (Bureau of Mines Schedule 21B), shall be used. mittee with regard to the proposed rules. (2) When the 8-hour time-weighted The committee will be provided with copies of these proposals, together with 2 2.5 3.5 90 76 60 average concentration of asbestos dust is projected to exceed 25 fibers longer all pertinent factual Information which Is, or may become, available to the As A0 10 26 than 5 microns per milliliter but not to 0 exceed 250 such fibers, and when a con sistant Secretary, Including any Infor centration over a period of 15 minutes mation submitted by the National Insti tute for Occupational Safety and Tbe measurements under this note refer to the use of an AEC instrument. If tbe respirable fraction of ooal dust is determined with a MRE the figure corresponding exceeds SO fibers longer than 5 microns per milliliter but does not exceed- 500 Health. The advisory committee will be to that of 2.4 Mg/M* in tbe table for ooal dost is 4A Mg/M, such fibers, a powered filter positive asked to submit to the Assistant Secre tary written recommendations regarding these proposed rules within 45 days after the publication of this notice. The 2. A new 11910.93a Is proposed to be added to Part 1910, reading as follows: g 1910.93a Asbestos dust. pressure respirator approved by the US. Bureau of Mines under the provisions of 30 CFR Part 14 (Bureau of Mines Sched ule 21B) shall be used. recommendations will be available for (a) 8-hour time-weighted average. (3) When the 8-hour time-weighted public Inspection and copying. No other advisory committee will be consulted with regard to these proposed rules. Part 1910 of Title 29 of the Code of The 8-hour time-weighted average air borne concentration of asbestos dust to which employees are exposed shall not exceed 5 fibers longer than 5 microns per average concentration of asbestos dust is projected to exceed 250 fibers longer than 5 microns per milliliter a type "C" positive pressure supplied-air respirator Federal Regulations is proposed to be amended as follows: S 1910.93 [Amended] milliliter, as determined by toe mem brane filter method at 400-450 x (mag nification) (4 millimeter objective) phase contrast illumination Concentra approved by the US. Bureau of Mines under the provisions of 30 CFR Part 12 (Bureau of Mines Schedule 19B) shall be used. 1. Table G-3 to { 1910.93 (36 FJt. tions above 5 fibers per milliliter, but not (4) The employer shall establish a 15104, August 13, 1971) Is proposed to be to exceed 10 fibers per milliliter,, may be respirator program in accordance with amended by deleting the following: permitted up to a total of 15 minutes to the requirements of American National Asbestos--12 fibers per milliliter greater than 5 microns In length or 2 Mppcf. Tremollte 6 Mppcf. %sio. an hour, but for not more than 5 hours to an 8-hour day. (b) Methods of compliance--(1) Engineering methods. Engineering Standard Practice tor Respiratory Pro tection Z88JS--1969. (5) The respirators provided each em ployee shall be properly inspected, If so amended. Table G-3 would read as follows: Table G-3--Mineral Dusts methods, such as, but not limited to, en closure, vacuum sweeping, and local ex haust ventilation, shall be used to meet the exposure limits prescribed to para cleaned, repaired, and stored. (d) Particular operations and prod ucts. (1) When an employer has employ ees who are exposed to asbestos dust re Substanoe graph (a) of this section. Where such sulting from the operations or the use Mppcf Mg/M> engineering methods are not feasible, or of tools described to the remaining sub- Bflica: Crystalline: do not reduce the concentrations below . paragraphs of this paragraph (d), the toe limits prescribed to paragraph (a) employer shall comply with the require Quart* (respirable). 360< Khng/M1 * of this section, respiratory protective de ments of this paragraph. The require Quarts (total dost).................... ........ . %S10rf2 30mg/M* vices shall be provided and used to ac cordance with subparagraph (2) of this ments of this paragraph shall apply at all times, and, in addition, the require Cristobal]t Vse M the alue calculated from tbe oount or mass formulae for auart*. %8iOH-2 paragraph. (2) Other methods, (i) When toe ments of paragraph (b) of this section may also apply, according to the terms limits of exposure to asbestos dust pre thereof. scribed in paragraph (a) of this section (2) All hand- or power-operated tools Tndymite: Use tbe value calculated from the for mulae for quart*: are exceeded, and engineering controls which produce asbestos dust such as, but required by subparagraph (1) of tois not limited to, saws, scorers, abrasive FEDERAL REGISTER, VOL 37, NO. 7--WEDNESDAY, JANUARY 12, 1972 412259 0197 468 PROPOSED RULE MAKING wheels, drills, shall be provided with dust in exoess of the limits specified in In every employment and place of em local exhaust ventilation and dust col paragraph <c) <3> of this section shall ployment covered by 1 1910.12, 1910.13. lectors In accordance with the American be monitored In accordance with this 1910.14. 1910.1S. or 1910.16 at this Sub National Standard Fundamentals Gov paragraph. part B, in Ueu at any different standard erning the Design and Operation of Do (i) Method. Dust samples shall be col on exposure to asbestos dust which es] Exhaust Systems; ANSI Z9.2--1071. lected from within the normal breathing would otherwise be applicable by virtue (3) Employees exposed to the spray zone of the employees in their normal of any of those sections ing of asbestos, to the demolition of pipes, structures, or equipment covered working posture. Employees wearing res piratory protective devices shall have (See. e. 84 Stat. 1693. 39 V.C CSS. 39 CFR 1910.4: Secretary of Labor'* Order Bo. 13-71. or Insulated with asbestos, or to the the sample taken from a point located on 3 FA 8764) demolition of insulating strippings, shall the exterior of the respirator facepiece. be provided with respiratory protective ill) Procedure. The sampling proce devices in accordance with paragraph dure shall be such as to permit the de Signed at Washington D.C.. this 6th day of January 1972. (c) (3) of this section. terminations required by paragraph (a) a. C Guchtbxr, " (4) Asbestos cement, mortar, coatings, of this section. Asst ttant Secretary of Labor. grout, and plaster shall be mixed in (ill) Sampling duration. The sampling closed bags or other closed containers. duration shall be for a period of not less |FB Dor 73-403 Filed 1-11 73:8:46 am) (5) Asbestos waste and scrap shall be than IS consecutive minutes. collected and disposed of in sealed bags <jv> Sampling frequency Sampling or other closed containers. periods shall be of such number and DEPARTMENT OF HEALTH, (6) Accumulation of asbestos dust pattern as to represent accurately the be removed, as soon as practicable, exposure of the employees over their and only by vacuum cleaners. working period. EDUCATION, AND WELFARE <e) Wonting signs--(1> Posting. <21 Environmental. Environmental Food and Drug Administration Warning signs shall be provided and monitoring shall be conducted in all displayed at each location where asbestos areas in which employees are exposed to [21 CFR Part 19 1 dust hazards are present. 8igns shall be concentrations of asbestos dust in excess posted at least 60 feet In each direction of the limits specified in paragraph (a) CERTAIN CHEESES from the location where the hazard is of this section Proposed Identity Standards present, and at Intervals of not more (1) Method. Asbestos dust samples Regarding Labeling Requirements than 100 feet along each edge of the area where the hazard is present. (2) Sign specifications. The warning signs shall conform to the requirements for 20" x 14" vertical format signs speci fied in { 1910.145(d) (2). and to this par agraph. The signs shall display the fol lowing legend in the white panel, with letter sizes and styles of a visibility at least equal to that specified in the nota tion in the following column to the right: Legend: Asbestos ______ Dust Hazard____ Follow these Safety and Health Buies.1 * * * S. 1. Avoid breathing dust. a. Wear your respirator. S. Do not remain In - area unless your work Notation 1" Sans Serif Gothic or Block. Vt" Sans Serif Gothic or Block. V Gothic % ' Sans Serif Gothic or Block 14" Gothic. %' Gothic V Gothic. shall be collected from areas which are representative of the concentration of airborne asbestos dust which may reach the breathing zone of exposed employees. <ii) Procedure Sampling procedure shall be such as to permit the determina tions required by paragraph '&> of this section. (Ui) Sampling duration. Sampling du ration shall be for a period of not less than IS consecutive minutes. (iv) Sampling frequency. Sampling periods shall be of such number and pattern as to represent accurately the exposure of the employees over their working period. (g) Medical examinations. The em ployer shall provide, or make available at his cost, appropriate medical exami nations on a periodic basis to any em ployee who is exposed to asbestos dust In excess of the limits specified in para graph (a) of this section. <h) Records. 1 > Every employer shall maintain records of the personal and environmental monitoring, and of the medical examinations, required by para Notice is given that a petition has been filed by the National Cheese Institute. Inc., 110 North Franklin Street. Chicago. HI, 60606. proposing that Identity stand ards for certain specified cheeses be amended to require that (1) the full name of the food appear on the principal display panel of the label in type of uni form size, style, and color. 2> wherever any word or statement emphasizing the name of any ingredient appears on the label (other, than in circumstances de scribed below so conspicuously as to Uc easily seen under customary conditions of purchase, the full name of -the food immediateh and conspicuously precedes or follows such word or statement in type of at least the same size as the type of such word or statement, and (3) op tional ingredients be listed conspicuously, either on the principal display panel of the label or on a single appropriate in formation panel In accordance with specifications that are consistent with similar specifications for many other food products Accordingly ,t is proposed that Part. requires it. graphs (f> and (g) of this section. Such 19 be amended Asbestos dust may cause esbestosls. a severe lung disease, and is implicated in the development of certain cancers. Con trol of exposure to asbestos dust helps 14 point Gothic. records shall be maintained for at least 20 years. (2) The records of monitoring shall be made available for Inspection and copying to the Secretary of Labor and to his designated representatives. (3) The records of medical examina 1 In 5 18 750'fi by revising subpara graph (6) and adding subparagraphs (71 and (8). as follows- 19.750 Pasteurized prorese cheese: identity; label statement of optional ingredients. protect against these tions shall be made available only to the hazards. Secretary of Labor, to the Secretary of (f) * * (3) Spacing. Spacing between lines Health, Education and Welfare, to desig (6) The full name of the food shall shall be at least equal to the height of the upper of any two lines, except that the spacing between "Following these" and "Safety and Health Rules" shall be at nated representatives of either of them, and, at the request of the employee or former employee examined, to his physician. appear on the principal display panel of the label in type of uniform size, style, and color (7) Wherever any word or statement least %". (f) Monitoring--(1) Personal. Em ployees engaged in the particular opera tions or using the particular tools speci 3. A new 11910.19 is proposed to be emphasizing the name of any ingredient added to Subpart B, reading as follows: appears on the label (other than as speci fied in subparagraph (8> of this, para g 1910.19 Asbestos dust. graph) so conspicuously as to be easily fied in paragraph (d) of this section, or Section 1910.93a shall apply to the ex seen under customary conditions of pur exposed to concentrations of asbestos posure of every employee to asbestos dust chase, the full name of the food shall FEDERAL REGISTER, VOL 37, NO. 7--WEDNESDAY, JANUARY 12, 1972 412259 0198 MEASUREMENT OFASBESTOS FIBERS Attachment #2 The sample should be collected on a 37-millimeter Millipore type AA* filter mounted in an open-face filter holder.. The holder should be fastened to the worker's lapel and air drawn through the filter by means of a battery-powered personal sampler pump similar to those approved by NIOSH under the provisions of 30 CFR 74. The filters are contained in plastic filter holders and are supported on pads which /also aid in controlling the distribution of air through the filter. To yield a more uniform sample deposit, the filter-holder face-caps should be removed. Sampling flow rates from 1.0 liter per minute (1pm) up to the maximum flow rate of the personal sampler, pump (usually not over 2.5 1pm) and sampling .time from 15 minutes to eight hours are acceptable provided the following restraints are considered: (a) In order to obtain an accurate estimate of the number of fibers the statistical error resulting from the random distribution of the fibers must be kept to an acceptably low level. Since fiber counts follow a Poisson distribu tion, a count of 100 fibers in a sample would have a standard deviation of 100 or 10 fibers or + 10%. Thus the 95% confidence limits would be approximately 2 standard deviations or + 20%. Since the 37 mm filter has an effective collecting area of 855 mm2 and the projected field area of the Porton reticle is 0.005 mm2 , each field rep resents 1/171000 of the sample. Based on this ratio the following number of fields must be counted to measure the various limits in various sampling times: Mention of commercial products does not constitute endorsement by the Public Health Service or U. S. Department of Health, Education and Welfare. VIII-4 412259 0199 Sampling Time Minutes 10 15 30 90 90 240 240 480 Flow Rate 1pm 2 2 2 1 2 1 2 1 Number of Fields for 100 Fibers 0.2 fibers/ml 2.0 fibers/ml 10 fibers/ml 4350 2860 1430 1000 500 260 180 180 435 286 143 100 50 26 18 18 91 ' 58 29 20 10 7 4 4 -- 0>) Do not count a field containing over 20 fibers because in addition to the fibers being counted, there are also present a number of grains, which interfere with the accuracy of the count. Based on these restraints, i.e., number of fields to be counted and maximum number of fibers per field, acceptable sampling parameters for the various limits are underlined in the above table. The following conclusions may be drawn from this analysis: (1) The short-term limit should be for a period of at least 15 minutes and preferably 30 minutes. (2) The 2.0 fiber/cc limit may be evaluated over periods of from 90 to 480 minutes. As many fields as required to yield at least 100 fibers should be counted. In general the minimum number of fields should be 20 and the maximum 100. Mounting Sample The mounting medium used in this method is prepared by dissolving -0.05 g of membrane filter per ml of 1:1 solution of dimethyl phthalate VIII-5 412259 0200 and diethyl oxalate. The index of refraction of the medium thus prepared is KD = 1.47. To prepare a sample for microscopic examination, a drop of the mounting medium is placed on a freshly cleaned, standard (25 mm X 75 mm), microscopic slide. A wedge-shaped piece with arc length of about 1 cm is excised from the filter with a scalpel and forceps and placed dust-side-up on the drop of mounting solution. A Ho. 1-1/2 coverslip, carefully cleaned / ' v? . with lens tissue, is placed over the filter wedge. Slight pressure on the coverslip achieves contact between it and the mounting medium. The sample may be examined as soon as the mount is transparent. The optical homogeneity of the resulting mount is nearly perfect, with only a slight background granularity under phase contrast, which disappears within one day. The sample should be counted within two days after mounting. Evaluation The filter samples mounted in the manner previously described are evaluated in terms of the concentration of asbestos fibers greater than 5 um in length. A microscope equipped with phase-contrast optics and a 4-ma ''high-dry" achromatic objective is suitable for this deter mination. 10X eyepieces, one of which contains a Porton or other suitable reticle at the level"of the field-limiting diaphragm, should be used. The left half of the Porton reticle field serves to define the counting area of the field. Twenty fields located at random on the sample are counted and total asbestos fibers longer than 5 um are seconded. Any particle having an aspect ratio of three or greater is considered a fiber. 412259 0201 The following formulae are used to determine the number of fibers/ml: (1) -Filter area (mm^) Field area (mm^) K (2) Average net count X K * fibers/ml Air volume -sampled (ml) Por example, assume the following: area of the filter used was . 855 nm^i counting area of one field under the Porton reticle was 0.005 mm2; average net count per field of 20 fields was 10 fibers; and sample was collected at 2 liters per minute for 90 minutes: Theni 855mm2 - 171,000 (K) " 0.005 mm2 # 10 fibers x 171,000 " 9.5 fibers/ml 2,000 ml/min x 90 min Calibration of Personal Sampler The accuracy of an analysis can be no greater than the accuracy of the volume of air which is measured. Therefore, the accurate calibration of a sampling device is essential to the correct interpretation of an instru ment's indication. The frequency of calibration is somewhat dependent on the. use, care, and handling to which the pump is subjected. Pumps should be calibrated if they have been subjected to .misuse or if they have just been repaired or received from a manufacturer. If hard usage is given the instrument, more frequent calibration may be necessary. Ordinarily, pumps should be calibrated in the laboratory both before they are used in the field and after they have been used to collect a large number of field samples. The accuracy of calibration is dependent oa the type of instrument used as a reference. The choice of calibra- tlon instrument will depend largely upon where the calibration is to be ..perfoinaed. For laboratory testing, a 1-liter burette or wet-test meter should be used. In the field, a rotameter is the most convenient VIII-7 4 412259 0202 instrument used. The actual set-up will be the same for all of these Instruments. The calibration Instrument will be connected in sequence to the filter unit which will be followed by the personal sampler pump. In this way, the calibration Instrument will be at atmospheric pressure. I Connections between units can be made using the same type of tubing used in the personal sampling unit. Each pump must be calibrated separately for each type of filter used,' if, for example. It has been decided * to use a filter with a different pore size. The burette should be set up i , eo that the flow is toward the narrow end of the unit. Care must be exercised in the assembly procedure to insure adequate seals at the joints and that the length of connecting tubing be kept at a minimum. Calibration should be done under the same conditions of pressure, temperature and density as will be encountered. The rotameter should be used only in the field as a check if the diaphragm or piston pumps are not equipped with pulsation dampeners. The pulsating flow resulting from these type pumps causes the rotameter to give results which are not as accurate as that obtained with a burette or wet-tast meter. Calibration can be accomplished with any of the other standard calibrating instruments, such as spirometer, Marriott's bottle, or drygas meter. The burette and wet-test meter were selected because of their accuracy,- availability, and ease of operation. Method based on a modification of the membrane filter method described by Edwards & Lynch "The Measurement of exposure to Airborne Mineral Fibers," Presented at the American Ind, Hyg. Conference, Denver 1969, VTII-8 412259 0203 Attachment #3 1 8330 OSHA SAMPLING DATA SHEETS FOR FIVE TOXIC SUBSTANCES RELEASED Back reference*: f 1071; 6647.93; 6647.93a. The Occupational Safety and Health Administration has released sampling data sheets for the five toxic sub stances on which its "Target Health Hazards" program will focus. The data sheets cover sampling equip ment and procedures for carbon mon oxide, asbestos, crystalline silica, lead and its inorganic compounds (except lead arsenate), and raw cotton dust. Criteria for violations of employee exposure to excessive concentrations of each substance are also described. The sampling data sheets are repro duced below. 8-hour time-weighted average*: S libers per milliliter greater than 5 microns in length. Excursion limit*: 10 fibers per milliliter, up to IS minutes in an hour for up to 5 hours per 8-hour day. Unprotected or improperly protected worker exposures Analytical Method: Fibers counted at 400-450 magnification, using phase contrast illumination, with sample mounted in high-viscosity solution of membrane filter material. Sampling Equipment: Personal sampling pump plus Miliipore type AA filter (37mm, 0.8 > pore size). Face cap is removed and filter used open face during sampling. Sampling rate: 21/m. Sample Size: Minimum period of 15 minutes for evalua tion of excursion limit. .Several samples of up to 4 hours for evaluation of 8-hour average. Samples with a visible deposit may be too heavy to count. Compare with a clean filter. Heavy concentrations of visible dust in the air (100 to 500 fibers/ml) may require short sampling periods of only 5 minutes, or less. Blanks: With each batch of samples submit two fil ters which are subjected to exactly the same handling as for the samples except that no air is drawn through them. Label these as blanks. Shipping: The cassettes in which the samples are col lected should be shipped in a suitable con tainer, designed to prevent damage in transit. Imminent Danger Situations: Generally not applicable. OSHA SAMPLING DATA SHEET #2 Substance: Asbestos. Standard: 29 CFR 1910.93a(a) of December 7, 1971 1 8330 Serious Violation: 5.1 or more fibers per ml, greater than 5 , in length, for an unprotected or improperly protected worker, for an 8-hour timeweighted average, except for certain proven excursions as noted in the emergency stand ard, which may raise the 8-hour timeweighted average to 5.8 fibers per mL Nonserious Violation: Not applicable. De Minimis Violation: Not applicable. 1972, Commerce Clearing House, Inc.