Document Rpa6LjBX9KRYYxqLXZOz3EX9V

FRICTION MATERIALS STANDARDS INSTITUTE, INC., EAST 210 ROUTE 4, PARAMUS, NJ 07652 BULLETIN NO. 856 June 16, 1986 COMMENTS ON EPA'S PROPOSED RULE TO BAN AND PHASE OUT ASBESTOS USES In our BULLETIN NO. 845 of February 12, 1986 we advised the Membership on EPA's proposals to ban and phase out the use of asbestos. The EPA plans were summarized in that Bulletin, and it was indicated that the Institute's Board of Directors would be meeting to consider an Institute position on these proposals. The Board of Directors met on March 11, 1986. This subject was discussed and the Board recommended that comments be made to the EPA essentially re affirming Institute positions taken in 1984 comments to the EPA and OSHA. 1 served on a Task Force with Mr. John Rlopelle, Chairman of the Health and Environmental Affairs Committee, to draft comments along the lines outlined by the Board. These comments were drafted and an original draft and two revisions were circulated to Officers, the Board of Directors, the Health and Environmental Affairs Committee, and Legal Counsel. With an extension granted earlier, the comments were due by June 29, 1986. The Institute mailed its comments, in triplicate (as requested by EPA), with its attachments of: EXHIBIT A - Our OSHA comments of May 22, 1984 EXHIBIT B - Our EPA comments of November 13, 1984 Copies of these earlier comments had been distributed to the Membership at those times, and are not attached to the copy being $0Rf*^Itfi this BulIeFtTK*^_ Our comments were sent to the EPA on June 13, 1986 lwFirst Class Certified Mail. ---------------- -------------- The foregoing is for your information. E. W. Drislane Executive Director Distribution: Delegates and Alternates H.E.A. Committee FMSI--0451 FMSI 02319 T RETURN RECEIPT, REOWTERED, INSURED AND CERTIFIED MAIL , MU your RETURN TO" (CONSULT POSTMASTER FOR FEES) D Show to whom and date delivered .O dat^j^d-addrew ofdelivery--t >. RESTRICTED DELIVERY (7V restricted deUrenfee to charged to addition to dte return receiptfee*) __t TOTAU S ftfficl^cjf^laxTc Substances te,T^lsWfris?,Tr Washington, DC 204a0 4. me OF samCE: RGoBmeo Qmsured Jjcmwm Ocoo TjEXPRESS MAI. ARIICtE NUMBER (wwiyt owm tgniw w Mipmii or iproi I have received the article decayed above. r""~ -- ~V<MTe OF DELIVERY *. ADDRESSEE'S ADORES*(0>4> Vmpmmt) FOOTMARK r.iMtaai* to deliver because: ^SRisr8 FMSI 02320 i UNITED STATES POSTAL SERVICE * OFFICIAL BUSINESS 3EN0ER IKSTHUCnOMS Printyour nwMdMM,in4 ZIP Coft Mhowoe* Mob. > ConaMOMra^a.i,iM4tMrni*. I MMBtnlnttMortUtH VOWOmAa i oinwsiwotnme>t j MonoaridOTMin Rmloi RosmUmT I U KMtMr. RETURN | Friction Materials Standards Institute ( i (Name of Sender) t I East 210 Route 4 ' ft (Street or P.O. Box) 1 ! 1 Pararaus, NJ 07652 ' s (City, State, and ZIP Code) FMSI 02321 TlLCAHONt <201 I 849-0440 FRICTION MATERIALS STANDARDS INSTITUTE, BERGEN MALL OFFICE CENTER E. 210 ROUTE 4 PARAMUS. N J. 07652 INC. June 13, 1986 Document Control Officer (TS-793) Office of Toxic Substances Environmental Protection Agency Room E-209 401 M Street, S.W. Washington, DC 20460 Subject: Asbestos Rulemaking Proposals (Docket Control Ho. 0PTS-62036) Gentlemen: The Friction Materials Standards Institute (FMSI) is a trade association of manufacturers of friction materials - brake linings and clutch facings. We wish to comment on the EPA proposals to prohibit and phase out the manu facture of certain asbestos products as detailed in the FEDERAL REGISTER Hotice of January 29, 198"6. Our comments are limited to the use of asbes tos in friction products. In either the basic proposals or in the options suggested, asbestos friction products would be prohibited oven ten years or over five years from the effective date of the rulemaking. We have responded in the past to proposals put forth both by the Occu pational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) concerning asbestos in friction products. We do not wish to add to the paper work we have sent earlier, but feel those comments bear repeating at this time. We are therefore enclosing copies of certain earlier comments which we wish to have considered in this rule making. EARLIER COMMENTS TO OSHA ON OCCUPATIONAL EXPOSURE TO ASBESTOS Enclosed are copies of our comments to OSHA of May 22, 1984. In those comments we described the uniqueness of the friction materials products as compared to other asbestos products, and the extensive work that had been done on non-asbestos friction products. We also noted the fact that the friction products Industry (with one exception in the past) uses only chrysotile asbestos in its products. The facts contained under "Friction Materials Product" in our May 22, 1984 comments are still appropriate. The remaining comments in that letter address certain areas of control. It is our belief that OSEA's proposed rules, if consideration is given to responsible comments, would provide the necessary control in the workplace to prevent any alleged unreasonable risk presented by exposure to asbestos FMSI 02322 T Environmental Protection Agency -2- June 13, 1986 In friction products. Since it is only in the workplace that significant exposure may occur and only when proper control devices are not in place, we do not believe that EPA's proposed phase out of asbestos in friction products is warranted. Please see our later comments in this letter on "Asbestos Exposure in the Brake Repair Shop." These earlier comments illustrate the dilemma for manufacturers of friction materials. OSHA, on the one hand, is proposing to reduce exposure levels in the workplace where there are substantial capital and on-going costs, while EPA is proposing a ban. We are persuaded that if proper controls are implemented in the workplace that friction materials workers will be adequa tely protected from the risks of asbestos exposure. EARLIER COMMENTS TO EPA ON PETITION TO BAN ASBESTOS BRAKE LININGS On November 13, 1984, we sent comments to EPA on the Natural Resources De fense Council (NRDC) Petition to prohibit the use of asbestos in on-highway brakes. We are enclosing copies of that letter as it is still relevant to the Issues raised in the recent proposals for a ban. We questioned whether or not the occupational asbestos standards and/or the national emissions standards were insufficient to protect against unreasonable risk posed by asbestos in brakes. In addition to our comments on OSHA versus EPA responsi bility, we commented on the use of substitutes and questioned the possible health effects where substitute fibers had physical dimensions similar to asbestos. We also noted that, while there had been substantial progress with semi-metallic disc pads, certain claimed advantages for semi-metallic materi als and other non-asbestos substitutes could not be extended to all friction product lines. While the industry is working on asbestos substitutes, and we realize that "free market" forces cannot rule where substantial health questions are in volved, the regulators should understand that these forces have been respon sible for the removal of asbestos from aircraft brakes several decades ago. These forces were responsible for the development of non-asbestos clutch facings in the heavy duty area and later in the passenger car area. These forces were also responsible for the success of semi-metallic (non-asbestos) disc brake pads as original equipment on the front brakes of a majority of passenger cars and light trucks today. The replacement of earlier asbestos- containing original equipment disc brake pads with later non-asbestos pro ducts requires the consideration of safety implications. The industry is working on substitutes for light, medium, and heavy truck drum segments, and on truck/trailer blocks. Progress has been made, but regulation with arbi trary cut-offs or phase downs is not the best way to Introduce safe and durable materials for a product so safety related as brake linings. PROPOSED PERMIT SYSTEM In the FEDERAL REGISTER Notice, the EPA proposed establishing a permit system for a phase out of asbestos products other than the specific products FMSI 02323 TT Environmental Protection Agency - 3- June 13, 1986 to be banned. This would affect asbestos friction products. We will not address the problems that would affect the importers of asbestos-contain ing friction products in establishing the base year allocations. Our comments address problems of the United States manufacturer. All United States manufacturers are importers of asbestos, with the main asbestos sources in Canada. All would be affected by permit requirements. While it is obvious that a new layer of bureaucracy would be piled on the American manufacturer, this system would tempt that manufacturer to lay in excess inventory where possible to avoid later permit delays or other snarls in the operation of a permit system. Factory operations must rely on dependable sources of supply. The lead times involved with non-asbestos substitutes may run to several years considering new equipment requirements to effect the process changes. Where technically feasible, bans on product lines or on sub-classifications of a product line would be preferable to a permit system, and considerably more workable. LABELING OF ASBESTOS FRICTION PRODUCTS The friction materials industry has been labeling its packages and cartons with the warning label required by OSHA. This label reads as follows: Caution Contains Asbestos Fibers Avoid Creating Dust Breathing Asbestos Dust May Cause Serious Bodily Harm This label has appeared on packaging where there was any likelihood that further machining might raise dust levels. We believe this has been a workable warning label. Where friction materials are being shipped to another factory or to a rebuilding operation, the warning is ordinarily passed on to the user with Inserts in the carton, in correspondence to the user, or with a stenciled warning on the container. The friction materials industry believes this warning is called for particularly where the carton is sold over the counter in an auto parts store, or by a mass merchandiser, or where the carton is delivered to a garage for Installation, even though additional machining is not likely to occur. We urge that EPA continue with the labeling called for by OSHA. ASBESTOS EXPOSURE IN THE BRAKE REPAIR SHOP There are essentially two procedures where the brake repair mechanic could be exposed to airborne asbestos. The first is while cleaning the brakes in need of reline, and the second is while preparing new brakes prior to installation on the vehicle. During the first operation, the mechanic is working on brakes where the airborne dust consists of friction material wear debris, road dirt, and dust. At this stage, the "fibers" are essen tially dust, without fiber orientation. This wear debris does not have FMSI 02324 Environmental Protection Agency -A- June 13, 1986 fiber length and diameter dimensions which OSHA would consider an "asbestos fiber." In addition, the wear debris has been chemically altered such that if it had not been known that the dust was derived from an asbestos contain ing product, this material would not be considered to contain asbestos. In years past, the only exposure to true asbestos fibers could have been while the mechanic was grinding, drilling, bevelling, or in other fashion, machining the new brake lining. Even in these Instances the asbestos fibers are not "pure" asbestos since asbestos fibers have been chemically mixed with resin and other raw materials, and then subjected to a curing operation which results in an alteration of the asbestos fibers. Over the past many years, most of this machining has been removed from the brake repair facility and transferred to the rebuilder or manufacturer who attaches the brake lining to the brake shoe. In certain cases, these opera tions have been further transferred back to the friction materials manufact urer. In the cases of both the rebuilder and the manufacturer, they are better able to control asbestos exposures than the brake shop, and by their very nature are exposing far fewer individuals than the 550,000 who are said to be exposed to asbestos during brake service. CHRYSOTILE ASBESTOS IH BRAKE LININGS Most studies have shown that there is a significantly lower risk of meso thelioma with chrysotile than with crocidollte and amosite. The Institute Members use only chrysotile in brake linings. Almost all reports on limited exposure and resultant malignancy have been based on finding mesothelioma in shipbuilding and construction workers, who were exposed to the amphiboles (crocidollte and amosite). We are not aware of mesothelial tumors in those exposed to brake lining dust absent exposure to the amphlboles. .Knowledge of the carcinogenic properties of asbeBtos developed from studies of exposure in the shipbuilding and construction industries where amphlboles were used, and the real damage that occurred in those areas has been sugges ted for the friction materials industry. The United States is one of but a few countries that treats all asbestos as equally toxic. It is suggested that regulation consider these differences and adopt lower exposure levels for crocidollte and amosite than for chrysotile, rather than a blanket pro hibition of all asbestos types. it * is is is Our industry is working on substitutes for asbestos in friction products. Several new non-asbestos type friction products have been introduced over the past several years. However, replacement of certain asbestos-containing brake linings with non-asbestos materials demands in-depth technical studies, expensive and time-consuming qualification tests, and in many cases the purchase of special equipment and tooling. These take time, particularly in the development of non-asbestos containing friction materials for the aftermarket where the performance must closely match that of the asbestos FMSl 02325 ir Environmental Protection Agency - 5- June 13, 1986 containing product in order to assure safe braking of the vehicles in question. Highway safety is a paramount concern, and our industry is regulated by a Federal Agency which demands safety. We ask that EPA re-consider its pro posed ban (or phase out) of asbestos friction products, and that any action taken along such lines be on a case-by-case basis. We suggest that EPA consider a reduction in asbestos exposure based on asbestos types - the chrysotile used in asbestos friction products being the least toxic type. We also suggest that EPA give consideration to the substitutes being used to replace asbestos, where the long term health effects of the substitutes are still open to question. While industry is working to develop substi tutes for asbestos, which we hope will be as effective as asbestos and themselves pose no significant risks to workers, we believe it would be imprudent for EPA to rush substitution before the safety and toxicology con siderations of substitutes have been fully assessed. Respectfully submitted, FRICTION MATERIALS STANDARDS INSTITUTE E. W. Drislane Executive Director Copies: Letter to OSHA 5-22-84 Letter to EPA 11-13-84 FMSl 02326