Document OzEoRRMymbnX6Mn8XjLKwzzGM

TECHNICAL SPECIFICATIONS CertairileedH T.C.O. REP. NO. SPECIFICATION NO: PAGE NO.: CertainTeed Corporation Pipe and Plastics Group 50 SUPERSEDES: 2 September 28, 1970 2-1 WAY 1980DATE OF ISSUE: 2b DESCRIPTION: FLUID-TITE A/C Sewer Pipe, Couplings and Accessories Classes 1500, 2400, 3300, 4000, 5000, 6000 and 7000 Sections A & B INDEX I tea lots. Foreword 1-1 SECTION B Iod*3t...................................................................... * ........................... 2-1 Central j-l lubber Ring................................... .... ................................... . 3-1 CERXA-SW.CLK band...........................................................................3-1 lubricant............................... .... ....................................... .... . . 3-1 Fackaglog. ........ ...................................................... 3-2 Chcaj'cal RcquIreaLT.t*. ..............................................................3-2 Caocral Product Description....................3-2 SECTION A (Sro 11 ^lioeter S.'vcr) Coofonu.ir.cc............................ 4-1 Pipe lengths.......................................................... 4-1 n.j,lcal Kiqulretruoes........................................................... .... . 4-2 Crushing Strcnteh ................................ ...... 4.3 Flexural Proof Louds. ..... 4-2 Jvlp.t lest.......................................................... 4-2 Korkin?. 4.3 r.puelil.......................................................4-5 Conforunce.................. .... . Pipe Lengths ....................... Physical Requirements. . Crushing Strength . Flexural Proof Loads, Out-oC-Round. . . . Joint Test.................. Marking. ... .................. Standard Pipe....................... Standard Coupling. . . . Manhole Stub ....................... iDrop Manhole Section End Cap. 'V. . . . . Increater-A/C to A/C . . Elbows .................................... 45 Vye Fittings .... 60 Wye Fittings .... Tee Flttlnga ....................... Standard ripe............................ .... ....................................... ..... 4-6 Standard Coupling. ...... 4-6 Sleeve Adaptor.................................................................................... 4-7 Sleeve Adaptor - A/C Rough Darrel to Clay. . . . . 4-7 Adaptor Bell and Spigot. 4-8 Inere*ser Adaptor - Cast Iron to Sever..........................4-6 duplex Adaptor Coupling - Clay Spigot to A/C M.E. 4-8 Duplex /. Japror Coupling - Concrete to J-/T. Sewer . 4-8 Duplex Adaptor Coupling - Cast Iron to Sewer . . . 4-9 Increoscr - F.T. A/C to K.T. A/C........................................ 4-9 Coupling Cn-J Plug..........................................................................4-10 End Cap....................................................................................................... * 4-10 Seuur Tcs Mpplc for Field Cut Mains................................ 4-11 45 Wyc Fittings............................................................................... 4-12 45 Double Vyc Fittings................................................................ 4-14 60 Vyc Fittings......................... .... ............................. . . 4-16 Tea Fittings........................................................................................ 4-17 Clbows.................... .... ........................................... .... ......................... 4-19 & 4-13 & 4-15 4 4-18 l3. . 5-1 . 5-1 5-2 5-2 5-2 5-3 . 5-3 . 5-4 5-6 . 5-7 . 5-8 1 5-6 . 5-9 . 5-10 . 5-11 . 5-12 4 5-13 . 5-14 4 5-15 > 5-16 4 5-17 CTD015294 PREPARED BY: AZX- APPROVED BY: R *O MFO. SALES I.E. m J.4.A. Q. C. 02-10-0023 4/80 CONFIDENTIAL DOCUMENT - NOT TO BE DISTRIBUTED TO UNAUTHORIZED PERSONNEL OTHERS OCftCRIPTlON: OAT* OP IMUC; MAY 2 8 1980 SPECIFICATION NO: 2 PAOC NO.: 3-1 FLUID-TITE A/C Sewer Pipe, Couplings and Accessories Classes 1500, 2400, 3300, 4000, 5000, 6000 and 7000 - Sections A & B GENERAL This specification designates the requirements for P&PG FLUID-TITE Asbestos Cement Sewer Pipe. It is divided into two Sections, A and B. Section A deals with 4", 5" and 6" small diameter pipe, and is manufactured in three (3) classes, 1500, 2400, and 3300, and is intended for use in non pressure drainage systems, outside dwellings, septic tank systems, sub-surface disposal systems, and as sewer connections between dwellings and sewer lines. Section B is intended for use with 8, 10, 12, 14, 15, 16, 18, 20, 21, 24 inch pipe sizes and is manufactured in classes; 1500, 2400, 3300, 4000, 5000, 6000 and 7000 and is intended for use in the conveyance of sanitary sewage in gravity flow systems. Available Classes Available Size Inches Section A Section B 1500 2400 3300 4000 5000 6000 7000 4, 5 and 6 4, 5 and 6 4, 5 and 6 -- --- -- --- 8-16 8-24 8-24 10 - 24 10 - 24 18 - 24 18 - 24 The class designations mean that the pipe and coupling shall be capable of withstanding the designated crushing strength in pounds per foot, when the pipe and coupling are tested in accordance with Method of Test ASTM C-500. Ripe linings.are available for special use in sizes 6" through 24". Rubber Rings Two rubber rings shall be furnished with each standard coupling. Standard or special rings shall be supplied with each fitting requiring rings. Rings shall meet the requirements of ASTM D1869 and A/C Standard Purchasing Specs. #506, 531 or 512. Oil-resistant rubber rings shall be furnished when specifically re quested provided there is sufficient lead time. Certa-Spacer Band One factory-applied CERTA-SPACER band (on prebelled side) must be furnished with each length of pipe. They shall meet all requirements of A/C Standard Purchasing Spec. #528. Lubricant Lubricant for use in field work shall be supplied in 5-ounce tubes, 1% quart containers or upon request by customer, 5 gallon pails. Lubricant shall meet all requirements of A/C Standard Purchasing Spec. #504. CTD015295 TECHNICAL SPECIFICATIONS CertairileedEI SPECIFICATIONS CLASSIFICATION: A/C Standard Product Specification T.C.O. REF. NO. SPECIFICATION NO: PAGE NO.: CertairiTeed Corporation Pipe and Plastics Group 49 SUPERSEDES: March 5, 1979 2 3-2 OATE OF ISSUE: SEP 2 8 19/9 description: FLUID-TITE A/C Sewer Pipe, Couplings and Accessories Classes 1500, 2400, 3300, 4000, 5000, 6000 and 7000 Sections A & B Pipe Size Inches No. of Joints Per 1% qt. containers No. of Joints Per 5 gal, pails 4 100 5 85 6 70 8 50 10 40 12 25 14 20 15 20 16 19 18 12 20 11 21 11 24 10 --- -- -- 725 545 415 280 270 260 170 155 145 135 Note: Fluid-Tite couplings in sizes 4, 5 and 6 inch a: and will have two joints per assembly. Sizes 8" and above are prebelled and therefore have only one joint per assembly. PACKAGING Packaging shall be in accordance with P&PG Standard Packaging Specification No.'s 2 and 3. CHEMICAL REQUIREMENTS Uncombined Calcium Hydroxide - 1.0 per cent maximum. GENERAL PRODUCT DESCRIPTION For products described in this specification, refer to page I, (Index) of this specification Section A and B. Refer to General Product Specification Data "Section D" of the General Standards Manual for information concerning the following: CTD015296 1. Composition 2. Installation Instructions 3. Finish 4. Straightness 5. Leakage Allowance 6. Handling Label PREPARED BY: APPROVED BY: J.e/). 02-10-0023 (P927) 12/76 CONFIDENTIAL DOCUMENT - NOT TO BE l^TRIBUTED TO UNAUTHORIZED PERSONNEL Page 3-3 All A/C Sewer pipe and couplings shall be completely free of loose or hanging A/C chips in the interior. Machined outer surfaces of all pipe (regardless of length), fittings, and adaptors shall be free of hanging machined trim (lace curtains). The interior corner of the pipe nose shall be free of all loose or hanging chips. The approved method for cleaning the pipe interior nose is to use the I.D. bevel tool to break this corner. CTD015297