Document OEMg963J5QngeoE9RbRnJ2E3w

WORKING CONDITIONS AND MEASURES FOR THEIR IMPROVEMENT IN PRODUCTION AND USE OF VINYIiCHLORlDE FUSTICS. Tribukh, S.L., Tikhomirova, N. P., Levina, 5 V., Kozlov, I* A. Gigiena i Sanit. (10)*38-44(1949) The production of vinylchlorida plastics and also the different good prepared from them gained in the list decade considerable importance. In the meanwhile from hygienical point of view, it was little studied. The basic raw material for the preparation of vinylchloride plastics is vinylchloride resin, which is prepared from vinylchloride, a c lorlsss gas, condenses at 12 - 14 in liquid with a specific weight of 0,86 - 0.9 Vinylchloride, on its turn, is prepared by the reaction of gaseous decomp sition products of petroleum vapors (vinyl) and gaseous chlorine. Sub sequently, the vinylchloride condenses by using dichloroethane and is sub jected to polymerization in autoclaves. In this way, polyvinylchl ride resin is the product of vinylchloride polymerization. Due to the resist ance to alkali, diluted acids, ethers, benzin and lubricating oilpoly vinyl chloride resin is used for the preparation of acidresistant fillers fabrics for overalls, substituents to hides, etc. At the preparation of various goods, the polyvinylchloride resin is plasticized with complex ethers of phthalic acid (dibutylphthalate), phos phoric acid (tricresylphosphate), mixture of diphenylchloride (sovol), or chlorinated naphthalenes (golowax). The selection of the plasticizer de pends on the assigned use of the plastic to be prepared. According to the data of the literature, vinylchloride belongs to we narcotics. Its narcotic concentrations for humans are within the limits of 75 to 250 mg/1. According to the data by Petropavlovskii (1942), vola tile substances, liberated, when vinylchloride resin and plasticizers are heated to I3O-I650 cause in animals under the condition of one single inocculation, depending on the concentration, the following phenomena* UCC 057338 -2 irritation of the ocular mucous membrane* respiratory disorders* damag of the central nervous system* breakdown in the coordination of movements* ar. death* after appearance of asphyxic convulsions. Sovol and golowax* introduced into vinylchloride plastics, as plasticizers, have general and local toxic effect. In their overall action on the organism* sovol and golowax are close to chlorinated fatty hydrocarbon Basically they attack the parenchemal organs. Severe toxic effect takes place in form of acute* or subacute yellow atrophy of the liver. In the literature* cases with lethal outcome are described, caused by the toxic effect during the production with vinylchloride naphthalene? (golowax}. and diphenyls (sovol). The local action of sovol and golowax causes acne-type skin eruptions and erythematous-vesicular dermatitis. We studied the working conditions at the finishing of vinyl chi ride plastics under factory conditions in a vinylchloride plastic plant, using vinylchloride plastics as substituent for hides and for insulation of electric wires. Production of vinylchloride plastics- In the vinylchloride plastics plant, the vinylchloride resin (a white powdery mass) is mixed with dibuty phthalate, or with sovol in mixing apparatus, at a temperature of 80-100. Then, the compound is transferred onto rollers, the surface of which is heated to 130-l60V. At the end of the rolling, the vinylchloride fabric is cut up in nar row tapes, which are further sorted and packaged in boxes. UCC 057339 During the hygienical inspection of the vinylchloride plastic plant, the air of the working place was examined on its sovol-. organochlorine compound-, and hydrochloric acid vapor content. The obtained results are plptted in Table 1, Table 1- Organochlorine compound, sovol and hydrogenchloride content in the air of vinylchloride plastic plant 1 Ko-iBiarpmia 1 xi.i Hajeajite oxae'entt / Me;?} uaxaa npcSii z uopopraaaaecaae coeiHae iua. ton eaeae coaoa 3a. uopacruft oaopoi 3b Fioiroxoiuxenbaoe 3 B ntijy ah noi:*pei *. coeoaa ........................ jj B ce;*;aje no**ia* * it yposee auxadxa pafiwro tr C-4eui>iiMa n io y c**:vT4a to ? 3 aaabaaaiut 6 To xe 11CMi*emcemae=i;hnto*njn*o.i>e0.it0ipcu. a. urpyacx kombo3mb:UI . . . Itt Ha patten xecte iut< no.niki........................ S /J V ctcai ana ocidijisaero naacTMKira ...................... -7 CacpaoBOt-ioe y1/0 pi:aaero xecia ;iep- ioinuuu . ................... 0,035 4 He oA.tapy|| 0.003 a 0,06-0,08 0,0^5 C,01-O,( n FHe oftupyxea 0.2*-097 i O.ivJ 0,27 19 Its oOuapyxeu 0,005 ! * * 1, Name of the department i 2. Place of the sample taking 3* concentra- ti n in mg/li 3a. organochlorine compounds,included sovol1! 3b, hydroge chloridet preparation! 5. mixing and rolling! 6. the same! 7. dril ling! 8. in the exhaust hood of the heated sovol! 9. in the middle of the chamber, at the respiration level of the workers! 10, at the mixer at-the time when the components were mixed) 11. at the mixture, at the time when the components were discharged! 12. at the working place of rolling! 13* at the deck for the cooled plastic compound! 14, at the working place of the drill operator! 15. not detected!. In the air of the working places of the vinylchloride plastic plant, as one can see this from the data of Table 1, the concentration of rgano chlorine compounds fluctuated between 0,005 to 0,27 mg/1. In the prepara ti n department sovol vapors formed at its heating, discharging and trans p rtation. The concentrations of organochloride compounds, found in this place (0,005 mg/1) can be attributed, most likely, in great part to sovol On account of the insufficiently developed method to determine separate! organochlorine compounds, they were determined summarily. UCC 057340 At the mixers the organochlorine compounds were found in an amount from 0(01 to 0t08 mg/l* and in the working place of the rolling - from 0,2 t 0,97 mg/l. In the product sorting department the organichlorioe compounds, usue ly, did not exceed 0,05 mg/l* We detected hydrogenchloride only in the di ferent samples in amounts, not exceeding thousandth' part of milligram. In connection with the use of sovol, soiling the skin with ingredieni in the composition of which sovol was introduced causes serious danger. Or the skin of the hands of the workers we found organochlorine compounds. To fight the contamination of the air, the plant was mounted with influent and exhaust ventilation with automatic driving. The exhaust ven tilation was constructed on the principle of local exhaust from the hood?, placed over the basic sources of gas evolution. The efficiency of the ventilation, as this was demonstrated by the sanitary-technical inspection,was insufficient, on account of the fact,th: the air-feed was carried out with a rate of only 7-8 a/sec on the level f the shoulders of the workers. The unpleasant sensation, caused by si milar way of air feed, together with the infiltration and cooling f the compounds on the rollers forced the workers to overlay the damper of the sprinkling valves and already with this, the air current, escaping throug) the different leakages, decreased the work of the exhaust device, deviat ing the convective current, which got up from the rollers* 3esides, the closing of the influx nozzle, disrupted the balance between the influx an the exhaust and attracted inorganized admission of contaminated air from the neighboring places. A significant defect of the ventilation system was th insufficient efficiency of the low-capacity hoods, arranged over the decks for the ready products and over the mixers. Much more effective are, according t our project executed orifices over the mixers in form of tents with open front wall (see the figure). At a productivity of 1 000 these orifices practically completely localised the separation of noxious gas. Scheme of the tentlike openings of the mixer. Use of vinvlchloride -plastics as substituent for hides i- In the pro duction of vinylchloride footwear, the basic raw material is polyvinyl chloride resin, which is prepared by the polymerisation of vinylchlorid in a water-emulsion method. The temperature of the decomposition of this resin is 130 - 150. As plasticizer here dibutylphthalate and as stabiliz er potassium stearate is used. The compound for the sole is prepared by mixing textile scraps, sa turated with dibutylphthalate, and vinylchloride resin in the mixer. The obtained compound is piled on the heater to 170 - 200 and rubbed through after this with Vaseline in the press mold. The, in this way filled pres; form is closed, it is maintained for a few minutes, and then is placed fo: a short time under the hot press. 057342 --- The composition for the upper footwear is obtained by mixing a deter mined amount of polyvinylchloride resin and dibutylphthalate in the mixer. The mass is kept there for aging 12 hours at a temperature of 70. After the aging the compound*is rolled at a temperature of 120-140 with the ad dition of potassium stearate* The vinyl chloride plastic compound* obtain* after the rolling is rapped in textile and pressed at m temperature of l6o` The analysis of the air for noxious gas and vapor content in the plan of vinylchloride footwear production is plotted in Table 2. Table 2- Concentration of gases and vapors in the air of working places Tin vinylchloride footwear manufacturing plants in mg/1 Macro niTaa j (cyxiiapNO) < coamaTpam a xrfa 0,033 0,019 0,01 1. place of the sample takingi la. at the rollersj lb. at the pr ss; lc. at the welding place2.organochlorine contentj 3. minimumi 4. maximu 5. averaget 6. concentration in mg/lt 7. total. The organochlorine compounds, which evolve at the thermal finishing o vinylchloride resins, represent cleaved molecules of vinylchloride in dif ferent quantitative chain compound compositions. In the air of the workin places at the manufacturing of vinylchloride footwear, we found these com pounds in an amount from 0,14 to 1,2 mg/1. Here we found also vapors of hydrochloric acid in concentrations from 0,008 to 0,17 mg/1, hydrocarbon vapors (determined summarily) from 0,21 to 2,6l mg/1 and carbon monoxide vapors within the limits of 0,01 to 0,022 rag/1. ucc 057343 -7- The contamination of the atmosphere by organochlorine compounds and vapors of hydrochloric acid increases in proportion with the temperature increase at the heating during the different manufacturing operations. The ventilation of the working place was carried out by means of a fe exhaust devices, originally destined for local exhaustion. In spite of th comparatively ... high frequency of air exchange (10 - 20), the effi ciency of the ventilation was insufficient. Its basic imperfection was tk lack of local removal of the gasf evolved during the work at the pressing rolling and welding of the footwear. The hood over the welding working benches, usually used in this kind of production, was not efficient and could not be considered as a 1 cal e> haust device, because at the welding of the vinylchloride footwear, the gases evolved on the level of the knee of the seated welder, in the imme diate closeness to his face. A more radical device in the given case is e vertical exhaust channel against each working place. The removal of th air can be carried out through orifices in the platform of the working ber the upper part of which, thus, should be used as planar exhaust channel. Satisfactory effect can be observed also in case of exhaust through e horizontal box, arranged on the surface of the working bench. The rate of suction through the exhaust orifices should not be less than 6 m/sec. Use of vlnylchlorlde plastics for the insulation of electric wires- In the factory, where vinylchloride plastics are used as insulating materi for electric wires, the covering of the wires with vinylchloride envel pe, is carried out on extruders. During the time, when the vinylchloride plastic compound is dried in the drying chambers, and also at its fusion and at the discharge of the wires from the hot envelope from the head of the extruder, in the air of the working space we found the following volatile substances (Table 3). UCC 057344 Tabl 3 MecTO until npotf h Xaopopra* H1MCKM eoeigMMa '< ta 11. . a I 22 s; ss 1 HCI !C | (cytnupHO) i" KtMUtHTpaoiM nr,'! CO I1 i Vs* 9 S 5* UM39s 3S ii 2 a as, 4< J3r m 32 j*/1 Z3 s1 *:. y atnpmivami <w aoae JiuxuHi paftouro . . . Hu npoioj?*. noipwTtiM t ropaieft niacTiaccoi . . B cepeiNic iiomuiihii it o e ! O.C04 0,1 o.w; 0,06 j o,:?'o,65, Hi o4u- pyxtii To ice 0.3 0,6 - i o.it ^1 0.017 o.i i 0.02 j 0, 0 0.14 -- 0,016 0,06 j 0,2? j 7 1. Place of the sample taking? 2. organochlorine compounds? 3. con entration In mg/li 4. summarily? 5* at the extruder in the zone of th worker: respiration? 6. over the wire, coated with hot plastics? 7. over the drying chest, 8. was hot ffeteetedt 9. minimum? 10, maximum 11. in the center of the place. In the composition of the volatile substances, evolved at the heating f the vinylchloride plastics, up to 120 - 140, there is an organochlo- rine content of 0,003 to 0,6 mg/1, vapors of free hydrochloric acid from 0,001 to 0,06 mg/1, hydrocarbon vapors from 0,08 to 0,6 mg/1, and carbon monoxide vapors from 0,01 to 0,05 mg/1. The ventilation of the plant was accomplished by means of exhaust hoods, arranged on the telescopic downstroke over each extruder head. The gases, evolving at the drying of the plastic compound in the drying chest and at the cooling of the vinylchloride wire after discharging from the extruder head, arrived in the atmosphere of the working places,maintaining in them a considerable concentration of toxic substances. UCC 057345 0 Results of the medical examination of the workers;- A randomly se lected group of workers In the Inspected plant was subjected to medical e: amination* In the vinylchloride plant 48 men were examined, mainly rolls: workers. At the rhino-larynx examination, in a great number of the workers, in the upper respiratory tracts (in the nose, larynx, and thnach< white films of dust were observed, which were formed as a result of the mixture of dust with the mucus* These films were compscc at the touch anc could be removed from the surface of the mucous membrane only with diffi culty. In 17 men hyperemia of the mucous membrane of the upper respiratoi tract was found. Chronic bronchitis was detected in 13 raeri. As to the change in blood circulating organs, one must mention vascular hypotonia (90 - 100/45 - 50) in 13 men, moderate hypertonia in one, arterio-cardi - sclerosis - in 5. The condition of the gastro-intestinal tract was charac terixed in 10 examined workers by chronic gastritis and in 2 by chronic colitis. In 15 workersthere were alterations in the liver in form of more or less pronouncedhepatitis, accompanied in 2 examined workers by cholecystitis. Regarding the blood, 29 examined workers had low hemoglobin count; or - 46, 22 50-55^, and 6 56-6OJS, The blood picture and the ROE were wit* * out peculiarities. One must pay attention to the skin diseases (acne, bleakheads), es pecially on the face, the neck and the chest, found in the examined gr up. The skin injuries were found not only on the face of those who were in contact with sovol, butalso on those, who were not in direct contact with it, but were working in the same place. Evidently, the skin disease was caused by the action of sovol, when its vapor was sorbed. UCC 051M6 In the chemical plant 25 female workers were examined* mainly those* working at the presses and welding with a long working record of 3 - 6 years in the said professions* In some of them* examined for ear - laryi different degree of hyperemia of the mucous membrane of the upper respira tory tract was observed* on its whole extent* or only on the organic part: Chronic bronchitis was found in 5* mildly expressed emphysema of the lung: in 3 and remaining signs of pleurisy in 2. As to the cardio-vascular system in 14 men vascular hypotonia (R/R 90 - IIO/55-65) and in 4 mildly expressed hypertonia (rA 140 - 165/ 085) was detected* Thudding sound of the heart* its enlargement ana the data of the ECGs Low T-wave of heart, not less than by 2 basic abcuctioi and the roundness of the S - T interval* gave foundation* in some cases* to diagnose distrophy of the myocardium. In the examined group* in 6 workers hepatitis was diagnosed. At the same time*in some persons*'simultaneously liver and stomach disease was d< t cted. Not in one of the liver disease cases could we find in the anam nesis* or at the examination,signs of jaundice. Neither did we detect an; bile pigment in the urine. In a considerable number of the examined work ers small swelling of the liver* without characteristic pain and sensitiv: ty at palpation was observed. Analysing the results of the medical examination* one must remark* that in a known part of the workers, changes in the upper and deeper res piratory tracts were detected. These findings are confirmed also by the data of the literature. One oust pay attention to the high percentage of skin injuries, whici is* no doubt connected ethiologically to the action of sovol. UCC 057347 The pres nee of hepatitis in some workers, in contact with vinylchlo ride resin and vinylohloride plasticizers deserves serious consideration Therefore further dynamic observations on the state of the health of the workers, who are in contact with vinylchloride resin and its plasticizers are necessary, to prevent the development of severe liver damage. . *u1*f % 1, - Into the composition of volatile substances, which form at the thermal finishing of vinylchloride resins and plasticizers, during the manufacturing organo-chlorine compounds, hydrocarbons, vapors of free hydrochloric acid and of carbon monoxide enter, 2, The action of these volatile substances are manifested in the ir- ritation of the mucous membrane, mainly of the upper respiratory tracts) lengthy influence of finely dispersed dusts and vinylchloride resin vapor cause, besides, dryness and atrophy of the mucous membrane of the upper respiratory tracts, and is also responsible for the development of chr ni bronchitis, 3, A considerable number of hepatitis among the examined workers, and also the change in the upper respiratory tracts, raise the question of the necessity for further dynamic research on the state of the health of the workers and to take a series of therapeutic-prophylactic measures, in particular by organizing heat and moisture*inhalation of drugs foz the workers, U. At the use of vinylchloride sovol, as plasticizer, on most worke: acne type skin injuries, with preferable location on the face and neck, were observed. 5* For the prophylaxis of skin diseases at the work with sov 1, the following complex sanitary measures have to be taken* 1) securing for thf workers work underwear and outfit; #\ TM * (alkaline) 2) construction of sanitary showers ucc 057348 -12- with separate undressing for home and w rk cloths. At the sanitary pas sage, there must be a vapor chamber for the low temperature steaming of underwear and work outfit, at a temperature of 110-120* for one hour. The plant should be equipped with wash basins with hot and cold running water. 6. For the sanitation of the atmosphere, it is necessary to decrease as much as possible, the degree of vinylchloride resin decomposition at i thermal finishing. This must be attained by standardising its heat re sistance, and also by controlling the temperature when the rollers, the presses and other equipment are heated, not to exceed 120-130, Of extremely great Importance is the rationally equipped ventilation system, calculated on maximum screening-off the source of gas-, vapor- an dust separation. In connection with the fact, that in some factories the inflammation of the condensate was observed, which occurred in the exhaust ventilation tubes in contact with open flame, the exhaust apparatus must be projected by observing the conditions, adopted by the construction legislation f r construction , designated for the mixing of inflammable gaseous mixtures. UCC 057349