Document O3LXexGX2JK4pZYb9rXOzEJZL

* TELURA 521 E^ON COMPANY USA A DIVISION OF EXXON CORPORATION DATE ISSUED: OG/25/87 SUPERSEDES DATE: 07/15/86 MATERIAL SAFETY DATA SHEET EXXON COMPANY, U.S.A. P.O. BOX 2180 HOUSTON, TX 77252-2180 A. IDENTIFICATION AND EMERGENCY INFORMATION PRODUCT NAME TELURA 52V CHEMICAL NAME Petroleum Process Oil PRODUCT APPEARANCE AND ODOR Clear liquid, light yellow color Mild, bland petroleum odor EMERGENCY TELEPHONE NUMBER (713) 656-3424 PRODUCT CODE 3330B4 - 03084 CAS NUMBER 64742-65-0 or 64742-54-7 B. COMPONENTS AND HAZARD INFORMATION COMPONENTS CAS NO. OF COMPONENTS APPROXIMATE CONCENTRATION Solvent dewaxed heavy paraffinic distillate, petroleum or Hydrotreated heavy paraffinic distillate, petroleum 64742-65-0 or 64742-54-7 100% See Section E for Health and Hazard Information HAZARDOUS MATERIALS IDENTIFICATION SYSTEM (HMIS) Health Flammability Reactivity BASIS 11 0 Recommended by Exxon EXPOSURE LIMIT FOR TOTAL PRODUCT 5 mg/m3 for oil mist in air BASIS 05HA Regulation 29 CFR 1910.1000 C. PRIMARY ROUTES OF ENTRY AND EMERGENCY AND FIRST AID PROCEDURES 00 087144 CONFTDFNTTAl EYE CONTACT If splashed Into the eyes, flush with clear water for 15 minutes or until Irritation subsides. If irritation persists, call a physician. SKIN CONTACT In case of skin contact, remove any contaminated clothing and wash skin thoroughly with soap and water. INHALATION Vapor pressure is very low. Vapor inhalation under ambient conditions Is normally not a problem. If overcome by vapor from hot product, immediately remove from exposure and call a physician. If breathing Is irregular or has stopped, start resuscitation; administer oxygen, if available. If overexposed to oil mist, remove from furth r exposure until excessive oil mist condition subsides. 945-O277IMWHO01) TELURA 521 INGESTION If Ingested. DO NOT induce vomiting; call a physician Immediately. D. FIRE AND EXPLOSION HAZARD INFORMATION FLASH POINT (MINIMUM) 172.5*C (345'F) ASTM D 92, Cleveland Open Cup AUTOIGNITION TEMPERATURE Greater than 232*C (450`F) NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) * HAZARD IDENTIFICATION Health Flammability Reactivity BASIS 11 0 Recommended by Exxon HANDLING PRECAUTIONS Use product with caution around heat, sparks, pilot lights, static electricity, and open f1 ame. FLAMMABLE OR EXPLOSIVE LIMITS (APPROXIMATE PERCENT BY VOLUME IN AIR) Estimated values: Lower Flammable Limit 0.954 Upper Flammable Limit 1% EXTINGUISHING MEDIA AND FIRE FIGHTING PROCEDURES Foam, water spray (fog), dry chemical, carbon dioxide and vaporizing liquid type extinguishing agents may all be suitable for extinguishing fires involving this type of product, depending on size or potential size of fire and circumstances related to the situation. Plan fire protection and response strategy through consultation with local fire protection authorities or appropriate specialists. The following procedures for this type of product are based on the recommendations in the National Fire Protection Association's "Fire Protection Guide on Hazardous Materials", Eighth Edition (1984): Use water spray, dry chemical, foam or carbon dioxide. Use water to keep fire-exposed containers cool. If a leak or spill has not ignited, use water spray to disperse the vapors and to provide protection for men attempting to stop a leak. Water spray may be used to flush spills away from exposures. Minimize breathing gases, vapor, fumes or decomposition products. Use supplied-air breathing equipment for enclosed or confined spaces or as otherwise needed. DECOMPOSITION PRODUCTS UNDER FIRE CONDITIONS Fumes, smoke, carbon monoxide, aldehydes and other decomposition products, in the case of Incomplete combustion. "EMPTY" CONTAINER WARNING "Empty" containers retain residue (liquid and/or vapor) and can be dangerous. DO NOT PRESSURIZE. CUT, WELD, BRAZE, SOLDER. DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS OR OTHER SOURCES OF IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to clean since residue is difficult to remove. "Empty" drums should be completely drained, properly bunged and promptly returned to a drum reconditioner. All other containers should be disposed of In an environmentally safe manner and in accordance with governmental regulations. For work on tanks refer to Occupational Safety and Health Administration regulations, ANSI Z49.1, and other governmental and Industrial references pertaining to cleaning, repairing, welding, or other contemplated operations. E. HEALTH AND HAZARD INFORMATION VARIABILITY AMONG INDIVIDUALS Health studies have shown that many petroleum hydrocarbons and synthetic lubricants pose potential human health risks which may vary from person to person. As a precaution, exposure to liquids, vapors, mists or fumes should be minimized. EFFECTS OF OVEREXPOSURE (Signs and symptoms of exposure) Prolonged or repeated skin contact may cause skin irritation. 945-0277(MWH002) 00 087145 conftofNtta( * TELURA 521 NATURE OF HAZARD AND TOXICITY INFORMATION Prolonged or repeated skin contact with this product tends to remove skin oils possibly i leading to irritation and dermatitis; however, based on human experience and available toxicological data, this product is judged to be neither a "corrosive" nor an "irritant" by OSHA criteria. Product contacting the eyes may cause eye irritation. Product has a low order of acute oral and dermal toxicity, but minute amounts aspirated Into the lungs during Ingestion or vomiting may cause mild to severe pulmonary injury and possibly death. This product Is judged to have an acute oral LD50 (rat) greater than 5 g/kg of body weight, and an acute dermal LD50 (rabbit) greater than 3.16 g/kg of body weight. F. PHYSICAL DATA The following data are approximate or typical values and should not be used for precise design purposes. BOILING RANGE IBP Approximately 277'C (530`F) by ASTM D 2887 VAPOR PRESSURE Less than 0.01 mm Hg e 20'C SPECIFIC GRAVITY (15.6 C/15.6 C) 0.87 VAPOR DENSITY (AIR * 1) Greater than 5 MOLECULAR WEIGHT Approximately 340 PERCENT VOLATILE BY VOLUME Negligible from open container in 4 hours P 38"C (100'F) pH Essentially neutral EVAPORATION RATE *> 1 ATM. AND 25 C (77 F) (n-BUTYL ACETATE = 1) Less than 0.01 POUR, CONGEALING OR MELTING POINT -15'C (5'F) Pour Point by ASTM D 97 SOLUBILITY IN WATER P 1 ATM. AND 25 C (77 F) Negligible; less than 0.1% VISCOSITY 106 5SU 100' F G. REACTIVITY This product is stable and will not react violently with water. Hazardous polymerization will not occur. Avoid contact with strong oxidants such as liquid chlorine, concentrated oxygen, sodium hypochlorite or calcium hypochlorite. H. SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Recover free product. Add sand, earth, or other suitable absorbent to spill area. Minimize skin contact. Keep product out of sewers and watercourses by diking or impounding. Advise authorities If product has entered or may enter sewers, watercourses, or extensive land areas. Assure conformity with applicable governmental regulations. I. PROTECTION AND PRECAUTIONS VENTILATION Use local exhaust to capture vapor, mists or fumes, If necessary. Provide ventilation sufficient to prevent exce ding recommended exposure limit or buildup of explosive concentrations of vapor in air. Use explosion-proof equipment. No smoking or open lights. 945-0277IMWH002) DO 087146 CONFTDFNTIAl TELURA 521 RESPIRATORY PROTECTION Use supplied-air respiratory protection In confined or enclosed spaces, If needed. PROTECTIVE GLOVES Use chemical-resistant gloves, if needed, to avoid prolonged or repeated skin contact. EYE PROTECTION Use splash goggles or face shield when eye contact may occur. OTHER PROTECTIVE EQUIPMENT Use chemical-resistant apron or other impervious clothing, If needed, to avoid contaminating regular clothing which could result In prolonged or repeated skin contact. WORK PRACTICES / ENGINEERING CONTROLS Keep containers and storage containers closed when not In use. flame or strong oxidants. Do not store near heat, sparks, PERSONAL HYGIENE Minimize breathing vapor, mist or fumes. Avoid prolonged or repeated contact with skin. Remove contaminated clothing; launder or dry-clean before reuse. Remove contaminated shoes and thoroughly clean before reuse; discard If oil-soaked. Cleanse skin thoroughly after contact, before breaks and meals, and at end of work period. Product is readily removed from skin by waterless hand cleaners followed by washing thoroughly with soap and water. J. TRANSPORTATION INFORMATION TRANSPORTATION INCIDENT INFORMATION For further information relative to spills resulting from transportation Incidents, refer to latest Department of Transportation Emergency Response Guidebook for Hazardous Materials Incidents. DOT P 5800.3. DOT IDENTIFICATION NUMBER Not applicable The Information and recommendations contained herein are. to the best of Exxon's knowledge and beltef, accurate and reliable as of the date issued. Exxon does not warrant or guarantee their accuracy or reliability, and Exxon shall not be liable for any loss or damage arising out of the use thereof. The information and recommendations are offered for the user's consideration and examination, and it is the user's responsibility to satisfy itself that they are suitable and complete for its particular use. The Hazardous Materials Identification System (HMIS) and National Fire Protection Association (NFPA) ratings have been included by Exxon Company, U.S.A, in order to provide additional health and hazard classification information. The ratings recommended are based upon the criteria supplied by the developers of these rating systems, together with Exxon's interpretation of the available data. FOR ADDITIONAL INFORMATION ON HEALTH EFFECTS CONTACT: DIRECTOR OF INDUSTRIAL HYGIENE EXXON COMPANY, U.S.A. P. 0. BOX 2180 ROOM 3157 HOUSTON, TX 77252-2180 (713) 656-2443 945-027?(MWHCI02) FOR OTHER PRODUCT INFORMATION CONTACT: MANAGER, MARKETING TECHNICAL SERVICES EXXON COMPANY. U.S.A, P. 0. BOX 2180 ROOM 2355 HOUSTON, TX 77252-2180 (713) 65G-5949 DO 087147 CONFTDFNTTAl