Document O1w4jrjKRer2wbwD8KqgMmXwe

presH SttAtp Todmed fc^atm / L 66. Wm. 9 j Tfrwday. April y 19-- / Rales maS Ungtsha-- 19661 UB* ILIA 6Uto.J*aad CUM) biw been approyd by the Office of Mniwiirl and Budget |OMB) ndw the provisions of the Paperwork Redaction Act of 1900, 44 U&G 1501 el mnadbrnl--mltMiOMB control number 20OHBM. This regulation mi submitted to the Offioe of Management ond Budget (OMB? for review as required by E.O. 12291. Pursuant to the provisions of 5 U.S.C. B05(bk 1 bmbf certify isl Ads cuts, f promulgated, will not have a significant eceramic impact an any small entities. list of Subjects in 40 CFR Part SI Air pollution control, Asbestos. Beryliiuin. Hstsrdosi materials. Mercury, Vinyl chloride. Doted MwckSO.1964. WHtism D- ttackririwis, Administrator. PART 61--{AMENDED} 40 CTR Part SI is amended by redesignating Subpart B (If 81.20-6125] as Subpart M and revising the new Subport M to read as follows: Subpart M--National Emission Standard ter Sec 01.140 Applicability. 0LK1 Defadtions. 61.142 Standard hr aabeatos mills. 61.143 Standard for roadways* 61.144 Standard for manufacturing. 61.145 Standard fordemolition and renovation: Applicability. 61.146 Standard fotdpaafition and renovation: NotfSAm requirements. 61.147 Standard MmsMItion and novation: Procedure* for a*be*to* emission control. 61.148 Standard for spraying 61.140 Standard for fabricating. 61.150 Standard for insulating materials. 61.151 Standard for waste disposal for asbestos mills. 61.152 Standard for waste disposal for manufacturing, demolition, renovation, spraying, and fabricating operation*. 61.10 ' Standard far inactive waste disposal sites for asbestos mills and manufacturing and fabricating operation*. 61.154 Air-cleaning. 61.155 Reporting61.156 Active waste disposal sites. Authority. Secs. 112 and 301(a) ofthe Clean Air Ad. as amended (42 VS.C. 741Z 7601(a)]. additional authority as noted below. M--National Emission for Aabootoo Mb AppbcabWty. previsions of this subpart ore Me to those sources specified in through 61.153. apartinaatfraHifNni having ao --a M terms that araused hi tills subpart than few dmaltagaaBal od art not defined balow are given fra Facility component manna any pipe, some meaning es in the Act and In duct boiler, tank, reactor. turbine. or Subpart A of this part furnace at or in a facility: or any Active waste disposalsite means any structural member ofa ntcBMy. disposal afta other than an inactive site. Adequately wettedmeans sufficiently mixed or coated with water or an aqueous solution to prevent dust emissions. Asbestos means the asbestiform varieties of sarpenfinite (chxysotile), riebeckRe (croddoHte), cummingtonitegiumiiJIe, onthophyllito. and actinobtetiwwrflte. Asbestos-containing waste material/ means anyTmteThat contains ~ commercial asbestos and is generated by a source subject to the provisions of this aubpart This term includes asbestos mill tellings, asbestos waste from control devices, friable asbestos waste material, and bag* or containers that previously contained cofrunerdel asbestos. However, as applied to demolition and renovation operations. ffiSlefm ineludes only friable asbestos Friable asbestos material means_auy material containing more than 1 percent Mbeatoa bv weight tKaThand pressure can crumble putarol-- nr isfare to powder whan dry. Inactive waste disposalsite meana aay disposal site or portico ofit where SfbUtinwal materiel will not be deposited and where the surface is not disturbed by vehicular traffic. Manufacturing means the combining of commercial asbestos--or, In the case of woven friction products, the Combining of textiles containing commercial asbestos--with any bther nsaterial(s), including commercial asbestos, and the processing of this combination into a product Outside airmeans the air outside buildings and structures. waSe'Kfid asbestos waste from control Particulate asbestos material means devices;" -- finely divided particles of asbestos HsbesSas material meana asbestos or material. any material containing asbestos. Plannedrenovation operations means Asbestos millmeans any facility a renovation operation, or a number of engaged In converting, or in any such operatianjz ia which the amount of intermediate step in converting, friable asbestos material that will be asbestos-ore into commercial asbestos. remOVed or stopped within a given Outside storage of asbestos material is period of time can be predicted not considered a part of the asbestos Individual nonschedtiled operations are mfil. included if a number of ouch operations Asbestos tailings means any solid can be predicted to occur during a given waste that contains asbestos and is a period of time based on operating product of asbestos mining or milling experience. operations. Asbestos wastefrom control devices means any waste material that contains asbestos and is collected Id a pollution control device. *1 Commercial asbestos means any asbestos that is extracted from asbestos ore. DemaBtica means the wrecking or taking out of ariy load-supporting structural member of a facility together with any related handling operations. Emergency renovation operation means a renovation operation that was not planned but results from a sudden, Remove means to take out friable asbestos materials from any facility.' Renovation means altering in any way one or more facility components. Operations in which load-supporting structural members are wrecked or taken out are excluded Roadways means surfaces on which motorvehicles travel. This term includes highways, roads, streets, parking areas, and driveways. Strip means to take off friable asbestos materials from any part of facility. anexpectad event. This tana includes Structural member means any load operations necaasiteted by nonroutine supporting member of a facility, such as failures of equipment beams and loarf supporting walls; or any Fabricating agent any processing of a onload-supporting member, such as maaufai ImiittiWMiict that contains ceilings ana nonloadeapporting walls. commercial ttfijflbs, with the exception Visible emissions means any of processlngsnhuporary sites for the eminioni containing particulate constaction or {tistoration of facilities. asbestoa material that are visually Facility means' any institutional. detectable without the aid of commercial, or industrial structure, instruments. This does not include installation, or building (excluding condensed unoombined water vapor. c 000474 r' LAM022383 fmfatal Register / VoL 4ft Nq. Ofr / Thursday. April S. 1984 / Ruler and Regulation* components, all the requirements of (c) include the following information owner or operator of an aabeatos ii 0.141 and 81.147 apply, except a* in the notice: mill fhit either discharge no visible provided in paragraph (c) of this section. (1) Name and address of owner or omissions to the outside air from that (b| If the amount of friable asbestos operator. asbestos mill or use the methods materials in a facility being demolished (2) Description of the facility being specified bp f 91-154 to clean emissions is less than 80 linear meters (280 linear demolished or rknovated, inrhuHwg the containing particulate asbestos material feet) on pipes ami less than 15 square size, age, and prior use of die facility. 7 before they escape to, or are vented to. the outside air. maters (100 square feet) on other facility components, only the nnMfiaatfan requirements of paragraphs (a), (b). and (3) Estimate of the approximate amount of friable asbestoe material present in the facility?Por facilities fr (c) (1). (2). (3). (4). and (5) of 181.140 described in 101.145(b), explain ^ apply. techniques of estimation. _ ,\L. nianjyssl^sshTStiH tailings or (c) If the facility is being demolished (4) Location of the fodlity being asbestos-containing waste material on under an order of a State or local demolished or renovated. that roadway, unless it is a temporary governmental agency, issued because (5) Scheduled starting and completion> roadway on an area of asbestos ore the facility ie structurally unsound and dates of demolition or renovation. deposits. in danger of imminent collapse, only the (8) Nature of planned demolition or /fS1.144 Standard for manufacturing. (a) Applicability: This sectioa applies to the following manufacturing operations using commercial asbestos. (1) The manufacture of doth, cord, wicks, tubing, tape, twine, rope, thread, yarn, roving, lap, or other textile materials. (2) The manufacture of cement products. ..... (3) The manufacture of firajnSrfiiig requirements in 181.140 and in paragraphs (d). (e). (f). and (g) of i 61.147 apply. (d) If at least 80 linear meters (260 linear feet) of friable asbestos materials on pipes or at least 15 square meters (180 square feat) of friable asbestos materials on other facility components are stripped or removed at a facility being renovated, all the requirements of J f 01.140 ami 81.147 apply. (1) To determine whether paragraph renovation and method(s) to be used. (7) Procedures to boused to comply with the requirements of this Subpart. (8) Name and location of the wests disposal site where the friable asbestos waste material will be deposited. (9) For facilities described in i 01.145(c). the name, title, and authority of the State or local governmental representative who has ordered the demolition. and insulating materials, (4) The manufacture of friction (d) pf this section applies to planned renovation operations involving (Approved by the Office ofManagement and Budget under control number 2000-0284) products; (5) The manufacture of paper, individual nonscheduled operations, predict the additive amount of friable f 44.147 Standard tor i renovation: I millboard, and felt asbestos materials to be removed or emission control (S) The manufacture of floor tile. (7) The manufacture of paints, stripped over the maximum period of time a prediction can be made, not to coatings, caulks, adhesives, and * exceed 1 year. sealants. (8) The manufacture of plastics and (2) To determine whether paragraph (d) of this section applies to emergency rubber materials. (9) The manufacture of chlorine. (10) The manufacture of shotgun shell renovation operations, estimate the amount of friable asbestos materials to be removed or stripped as a result of the wads. sudden, unexpected event that (11) The manufacture of asphalt necessitated the renovation. \ concrete. j (e) Owners or operators of demolitions (b) Standard: Each owner or operator /and renovation operations are exempt f of any of the manufacturing operations [from the requirements of || 81.05(a), / to which this section applies shall either t.07, and 81.08. (1) Discharge so visible emissions to the outside air frxn these operations or tfif 01.148 Standard for demotion end Each owner or operator to whom this section applies shall comply with the following psocedures to prevent emissions of particulate asbestoe material to the outside she (a) Remove friable asbestos materials from a facility being dsnmlished or renovated bedim any wrecking or dismantling that would break up the materials or preclude access to the materials for subsequent removal However, friable asbestos materials need not be removed before demolition it- (1) They are on a facility component \ from any buildiigt or structure (n which Qi hYfOTVOTwms ivooncanan imumimiiib they are conduced; or Each owner or operator to which this / that la encased in concrete or other '^similar material; and J / (2) Use the meftods specified by f 81.154 to dean amissions from these operations cantoning particulate section applies shall: (a) Provide the Administrator with written notice of intention to demolish (2) These materials are adequately wetted whenever exposed during demolition. asbestos material before they escape to, or renovate. (b) When a facility component or are vented to. he outside air. (b) Postmark or deliver the notice as follows: covered or coated with friable asbestos materials ia being taken out of the 101.148 Stands* tor damoMon and renovation: AppnudUily. (1) At least 10 days before demolition facility as units or in sections: begins if the operation is described In (1) Adequately wet any friable The requiremaria of || 01.140 and 101.145(a); asbestos materials exposed during 81.147 apply to endt owner or operator (2) At least 20 days before demolition cutting or disjointing operations; and of a demolition arrenovation operation begins if the operation is described in (2) Carefully lower the units or as follows: i 01.145(b); sections to ground level, not dropping (a) If the amomCof friable asbestos (3) As early as possibla before them or throwing than, materials in a foailty being demolished demolition begins if the operation is (c) Adequately wet friable asbestos is at least 00 Unemmeters (200 linear described hi 101.145(c)) materials whan they am being stripped feet) on pipea or* least 15 square (4) As ratty as possible before from facility components before the meters (100 squawfeet) on other facility renovation begins. members are removed from the fodlity. mt C 000475 LAM022384 Fad--1 Register / VoL 48. No. 87 / Thnroday, April g, 1964 / Bute* md Rggdlatfbteg nawl In renovation operations, wetting that 161.146 g--MHarapraylng. would unavoidably damage equipment The ownaror operator of an operation th* outride air from any of th* l not required If the owner or operator in which eshestoe rnnielnliig operations or from any befldtag or (1) Aaks tha Administrator to an spray applied shall comply with the structure in which thsry are conducted: determine whether watting to comply following requirements: or with this paragraph would unavoidably (a) Un materials that <" l (2) Use the methods apedfled by damage equipment and, before beginning to atrip, supplies tha Administrator with adequate information to make thla determination: and (2) When the Administrator does percent asbestos or lees an dry weight basis for spray-on application on buildings, structures, pipes, and conduits, except as-provided in paragraph (c) of this section. (b) For spray-on application of 161.154 to dean emission* containing particulate' tabestoe material before they escape to, or are vented to, the outside air. 141.15* ftrodwdforbiiidemig mUrine determine that equipment damage materials that contain more than 1 After the effective date at this would be unavoidable, uses a local percent isbestoe on a dry weight basis regulation, no owner or operator of a exhaust ventilation and collection on equipment and machinery, except as facility may install or reinstall an a system designed and operated to capture the particulate asbestos provided in paragraph (c) of this section: facility component any insulating (I) Notify the Administrator at least materials that contain commercial material produced by the stripping and removal of the friable asbestos materials. The system must exhibit no 20 days before beginning the spraying operation. Include the following information In the notice: asbestoe if the materials are either ' molded end friable or wet-applied and friable after drying. The provisions of visible emissions to the outside air or be designed and operated in accordance with the requirements in f 81.154. (d) After a facility component has been taken out of the facility as units or (1) Name and address of owner or Ibis paragraph do not apply to spray- operator. applied Insulating materials regulated (II) Location of spraying operation. under 161.146k (Hi) Procedures to be followed to meet the requirements of this paragraph. (// 161.151 in sections, either (2) Discharge no visible emissions to (1) Adequately wet friable asbestos the outside air from the spray-on Each owner or operator of ally source materials during stripping; or application of the asbestos-containing covered under tha provisions of 161.142 (2) Use a local exhaust ventilation and collection system designed and operated to capture the particulate asbestos material produced by the stripping. The system must exhibit no visible emissiona to the outside air or be designed and operated in accordance with the requirements in | 61.154. (e) For friable asbestos materials that have been removed or stripped: (1) Adequately wet the materials to ensure that they remain wet until they are collected for disposal in accordance with i 61.15% and (2) Carefully lower the materials to the ground or a lower floor, not dropping or throwing them; and material or use the methods specified by i 61.154 to clean emissions containing particulate asbestos materiel before they escape to, or an venthd to, die outside air. (c) The requirements of paragraphs (a) and (b) of this section do not apply to the spray-on application of materials when die asbestos fibers in die materials era encapsulated with a bituminous or resinous binder during , spraying and the materials era not friable after drying. (d) Owners and operators of sources subject to this section an exempt from the requirements of If 61.05(a), 61.07, and 81.09. shall: (a) Deposit aO asbestos-containiof wests material at --ate disposal sites operated in accordance with the provisions at| folfo end (b) Discharge no visfoln emissions to the outside air from the transfer of asbestoe waste from control devices to the tailings conveyor, or use the methods specified by 161.154 to clean emlsaione containing particulate asbestoe materiel before they escape to, or are vented to, the outside air. Dispose of the asbestoe waste from control devices in accordance with 161.152(b) or paragraph (c) of this section; and (c) Discharge no visible emissions lo (3) Transport the materials to the ground via dust-tight chutes or (Approved by the Office of Management and the outside air during the collection, Budget under control number 20004264) processing, packaging, transporting, or containers if they have been removed or stripped more than 50 feet above ground level and were not removed as units or in sections. (I) When the temperature at the point of wetting is below 0*C (32'F): (1) Comply with the requirements of paragraphs (d) and (e) of this section. The owner or operator need not comply with the other wetting requirements in this section; and (2) Remove facility components ted or covend with friable asbestos iteriala as Asfoior in sections to the -UEv'Cyifcussible. 41.14* Standard for fabricating. ' (a) Applicability. TUa section applies to the following fabricating operation* using commercial asbestos: (1) The fabrication of cement building products. (2) The fabrication of friction products, except those operations that primarily install asbestos friction materials on motor vehicles. (3) The fabrication of cement or silicata board for ventilation hoods; ovens; electrical panels; laboratory furniture, bulkheads, partitions, and ceilings for marine construction; and deposition of any asbestos-containing waste materiel, or use one of the disposal methods specified in paragraph* (c) (1) or (2) of this section, as follows: (1) Use wetting agent as follows: (1) Adequately mix all asbestoscontaining waste material with a wetting agent recommended by the manufacturer of the agent to effectively --t duet and tailings, before depositing the material at a waste disposal site. Use the agent as recommended for the particular dnet by the manufacturer of the agent U For described in flow control devices for the molten (ii) Discharge no visible emissiona to -l45(c).'acHqoately wet the portion metal Chiustry. the outside air from tha wetting foe faeflity ftet contains friable (b) Standard. Each owner or operator operation or use the methods specified ; materials during tha wrecking of any of tha fabricating operations to by 161.154 to clean emissions on. which this section applies shall either: containing particulate asbestoe material C 000476 LAM022385 x3664 Federal Register / VoL 49, No. 07 / Thursday, April 5, 1986 / Rules sad Regulations before they escape to or us vented to. (i) Font all asbeatoa-eontatoing waste (i) B posted in socfc a manner and the outride rir. material into nonfriaUe pellets or othar location that a person can easily read (iit) Wetting may be euipendsd when shapes: and the legend; and the ambient temperature at the waste ' (il)Dtochtrya no risible emissions to (ii) Conform to die requirements for 51 disposal site Is lass than --PJTCftST), the outside suon eoUaetioa and cmx 30 cm (arxtr] upright format Determine the air temperature procssdMMdnmtfcmnorusetbe by an appropriate measurement method metbodanBlJpl by 18L1M to dean signs specified In 29 CFR 1910.145(d)(4) and this paragraph; and with an accuracy of 1*C(2*F), and record it at least hourly while the ' wetting operation is suspended. Keep the records for at least 2 years in a form suitable for inspection. emisshme enUining particulate (ill) Display dta following legend In aabestoa material before they escape tm or are vented to, the ootside air. the town panel with latter sizes and styles of a visibility at least equal to I',dia(3l)haUssreecaenivaeltdeprnraiotirvaepdpirsopvoaslablymtehtehod thoaa specified in this paragraph. (2) Use an alternative disposal method that has received prior approval by the Administrator. Administrator. 9 S1.153 Standard (Or inactive for Ugantf Maaew M OtpM 3*. U ca (t Ml Wm >* jsi.isa iwanutacturfog demoSMow. reoovsOon. ipciywiQ, ira iwuong opwootm manufactivtog and foOrfcaUngopanOonm Each owner or operator of any ' inactive waste disposal site that was OoNolCMiOM__ IS os (W M* torn M iiis*>s Ml to M MMnOoMs Each owner or operator of any sourca operated by sources covered under covered under the provisions of 91 Sl.lfl-M.149 shaft (a) Deposit all asbestos-containing 9161142.61.144, or 91.149 and received deposits of asbestos-containing waste material generated by the sources, shall Spacing between any two Unas must be at least equal to the height of the upper waste material at waste disposal sitea (a) Comply with one of the following of the two lines. operated in accordance with the provisions of 161.156; and (1) Either discharge no visible emissions to the outside air from an (2) Fence the perimeter of the rite ia a manner adequate to deter socesa by the (b) Discharge no visible emissions to inactive waste disposal site subject to general public the outside air during the collection, this paragraph; at (3Ufoon request end supply of processing (Including incineration), packaging, transporting, or deposition of any asbestos-containing waste material generated by the source, or use one of the disposal methods specified in paragraphs (bKl). (2), or (3) of this section, as follows; (1) Treat asbestos-containing waste material with water (1) Mix asbestos waste from control devices with water to form a slurry; adequately wet other asbestoscontaining waste material; and - (U) Discharge no visible emissions to the outside air from collection, miring and wetting operations, or use the methods specified by 161.154 to clean emissions containing particulate asbestos material before they escape to, or are vented to, the outside air; and (ill) After wetting, seal all asbestos* containing waste material in leak-tight containers while wet; and (iv) Label the containers specified ia paragraph (b)(l)(iii) as follows; CAUTION Contains Asbestos* Avoid Opening or Breaking Contrinw Breatiling Asbestos ta Uaurdoua (2) Cover the asbestos-containing wasta material with at least 15 centimeters (9 inches) of compacted nonasbestos-containing material, and grow and maintain a cover of vegetation an the area adequate to prevent exposure of the asbestos-containing waste material; or (3) Cover the asbestos-containing waste material with at least 60 centimstara (2 foet) at compacted nonasbestos-cantaining material, and maintain it to prevent exposure of the asbestos-containing waste; or (4) For inactive wests disposal litas for asbestos tailings, apply a resinous or petroleum-based dost suppression agent that effectively binds dust and controls wiitd erosion. Uaa the agent as recommended lor the particular aabestoa toiling by the manufacturer of the dust suppression agent Obtain prior approval of tbs Administrator to uaa other squally afbcttve dust suppression agents. For purposes of this psrapsph, wests crankcase oil is not considered a dust suppression agent (b) Unless a natural barrier adequately deten access by the general public; Install and maintain warning signs and fencing as follows, or comply apprapmata information, the Administrator will determine whether a fence or a natural barriar adequately deten access by the general pobtis. (c) The owner or operator may aeesa alternative control method that bee received prior approval at th* Administrator rather thaa comply with the requirements of paragraph (a) or (b) of this section. cU, < i 41.154 AtecHwitog.fcxilca^ 4 (a) The owner or operatorwheeled*^) to use aircleaning, as pemriBadby-- n 9310191144. iMIPMffh m i47(d)p),a.m(bKlL4i340h> (1) Use fabric filter collection devices, except as noted in paragraph (b) ofthis section, doing all of the following (i) Operating the fabric filter collection devices at e pressure drop of no more titan 4 inches water gaga as measured acroas the fitter fabric and (ii) Ensuring that the airflow permeability, ea determined byASTM Method D737-78, does not exceed 9 m*/ min/m* (30 ftVnrin/ft*) for woven fabrics or ll*/min/iaa(38 ft*/ndn/ft*) for felted fabrics, except the! 12 m*/ to Yoar Haaltb Alternatively, use warning labels specified by Occupational Safety and Health Standards of the Department of with paragraph (a)(3) or (a)(3) of this section. (1) Display warning signs at afi entrances and at intervals of 100 m (330 mln/m* (40 ft*mhi/ft*) for woven and 14 m*/min/m* (48 ft nrin/ft*) for foltad fabrica ia allowed for filtering air from asbestos ora dryers; and Labor. Occupational Safety and Health feet) or lass along the property line of (ill) Ensuring that fsltad fabric weighs Administration (OSHA) under 29 CFR' the site at along the protester of the at least 47S grams per square mater (14 1910.1001 (gX2HUJ- sections of tits site where asbestos*. ouncas per square yard) and Is at lesto (2) Procaee aabaatos-coataining waste containing waste material was 16 mffltestsra (cne-eixtaantil Inch) thick material into nooftiable forma: deposited The wanting rigna must: throughout; and ;| ft deal ore fori P sbs Oi fope mayi watq a unij kilopa pressi (2)1 tha ui thstdj (bHl)| opwrmt Admiii equivsf ftltertn tala i foUowi (2)1 cent across l gaga: on (fllfti fabric, t! min/m* whether and (Ii) If L felted fa airflow f (3) Fro and81.lt (i)Afc that gene waste mt C. 000477 LAM022386 Federal Register / Vot 49. Na 87 / Thursday, April 8. 198* / Ruler and tam (Iv) Avoiding the dm of synthetic fabrics that fill yam othar tbaa that which Is spun. (2] Property install use, operate. asd maintain sit afawlsmtng --pdpmmt authorized bjr tUa section. Bypass devices may ba oaad only during upset or emergency conditions and then only for ao Ion* aa It takaa to ahut down tha oparatioB generating die particulate aabeatoa matarlaL (b) There are the following exception* to paragraph (a)(1): (1) If the uae of fabric create* a fire or explosion hazard, tha Administrator may authorize aa a substitute the use of wet collectors designed to operate with a unit contacting energy of at least 9.95 ldlopascals (40 inches water gage pressure). (2) The Administrator may authorize the use of filtering equipment other than that described in paragraphs (a)(1) and (b)(1) of this section if the owner or operator demonstrates to the Administrator's satisfaction that it is equivalent to the described equipment in filtering particulate asbestos material. | St.155 Reporting. (a) Within 90 days after the effective date of this subpart each owner or operator of any existing source to which this subpart applies shall provide the following information to the Administrator, except that any owner or operator who provided this information prior to April 5,1984 in order to comply with 161-24 (which this section replaces) is not required to resubmit it (1) A description of the emission control equipment used for each process: and (2) If a fabric filter device is used to control emissions, the pressure drop ecross the fabric filter in inches water gage; and (i) If the fabric device uses a woven fabric, the airflow permeability in m*/ min/m* and: if the fabric is synthetic, whether the fill yarn is spun or not spun: and (II) If the fabric filter device uses a felted fabric, the density in g/m*. the minimum thickness in inches, and the airflow permeability in m*/min/m*. (3) For sources subject to f ( 81.151 and 61.152: (i) A brief description of each process Mi generates asbestos-containing a material; and (ii) Tha average weight of asbestos-1 styles of a visibility at team equal to containing waste material disposed at tboec specified in this paragraph. measured in kg/day; and (111)Ilia emission control methods used in all stages of water disposal: and' fa-- mmm (iv) Tha type of disposal site or Incineration sits used for ultimate disposal, the name of the sits operator, and the nama and location of the disposal site. .If.... -r-. UwdMtWsM OseMwnm. OoHMCraaaO1tW-------- i s cm (* M* am Ss* MSraMw OlfafmM. (4) For sources subject to 181.153: (i) A brief description of the site; and (11) The method or methods used to comply with the standard, or alternative procedures to be used. fb) Tha information required by paragraph (a) of this section must accompany tits information required by i 61.10. The information described in Spacing between any two Unas must bo at least equal to the height of the upper. of the two lines. (2) The perimeter of the dispoaal site must be fenced in a manner adequate to deter access by the general public. this section must be reported using the (3) Upon request and supply of format of Appendix A of this part appropriate information, the (Sec. 114. Clean Air Act ss amended (43 U5.C 7414)). (Approved by this Office ofManagement and Budget under control number 2000-0284) (81.158 Active waste dispesst sites. Administrator will determine whether a fence or a natural barrier adequately deters sccass by the general public. (c) Rather than meet tha ao visible emission requirement ofparaymph (a) of this section, an active waste dispoaal To be an acceptable site for disposal sits would be an acceptable site ifat tha of asbestos-containing waste material and ofeach operating day, or at least under || 81.151 and 61.152, an active once every ZShour period while the site waste disposal site must meet die is in continuous operetta*, dm asbestos- requirements of this section. containing waste inatariaf which was fa) Either there must be no visible deposited at th* sit* during the - emissions to the outside air from any operating dayorprevious M-hour period active waste disposal site where is covered with either. asbestos-containing waste material has been deposited, or the requirements of paragraph (c) or (d) of this section must be met fb) Unless a natural barrier adequately deters access by the general public, either warning signs and fencing must be installed and maintained as follows, or the requirements of paragraph (c)(1) of this section must be (1) At least IS centimeters (6 indies) of compacted nonasbestoe-containiag material, or (2) A resinous or petroleum-based dust suppression agent diet affectively binds dot and anjbtijb wind erosion. This agent must hlaied a* recommended for the particular dust by the manufacturer of die ifost met (1) Warning signs must be displayed at all entrances and at intervals of 100 m (330 ft) or less along the property line of the site or along the perimeter of the sections of the site where asbestoscontaining waste material is deposited. The warning signs must: (i) Be pasted in such a manner and location that a person can easily read the legend: and (ii) Conform to the requirements of 51 cm x 38 cm (20" x 14") upright format effemiv* dust suppression agents may be used upon prior approval by the Administrator. For purposes of this paragraph, waste crankcase oil is not considered a dust suppression agent. (d) Rather than meet tha ao visible emission requirement of paragraph (a) of this section, an active waste disposal site would be an acceptable sits If an alternative control method for emissions that has received prior approval by the Administrator ia used. signs specified in 29 CFR 1910.145(d)(4) (Sacs. 113 asd 3U(a) of the Ossa Air Act as and this paragraph: and amended (42 UAC 7413. 7801(a)) (iii) Display the following legend in ira Uae. IMMIW -* MS art the lower panel with letter sizes and MUMS COM HS4MI c 000478 LAM022387