Document MMjawMmxOZ1Ko7OqMwngJZbEz

TO: G.V. /D-/a - 74 OPERATING INSTRUCTIONS AROCLOR SUMP GENERAL: The sump maximum design rate of flow is 250 GPM and appears to be completely separating the second phase from the department effluent. The sump will hold 4000 gallons at a depth of around 3 1/2 feet. This is the maximum height of Aroclor the sump should have in it and should only occur after a major spill. In the north.west comer there is a pump suction pit 18" x 18" x 24". This pit will hold 34 gallons and should collect the Aroclor from the sloped floor. OPERATION: The pump pit should be pumped out as often as it fills up; ie. 34 gallons. Recom mend that the sump be pumped out once every two weeks. A small Randolph pump has been provided for this purpose. Collect the Aroclor and water in drums and haul to the dump. INSPECTION AND/OR MAINTENANCE: When it becomes necessary to pump the sump empty for inspection and/or repairs, the surrounding ground water must be pumped out first and kept out. A hole has . been provided for this on hte northeast and southeast corners of the sump. A pump has not been provided, but the pump should stay in place and run continuously during the time the sump is empty. ' The sump pit should be emptied of Aroclor as much as possible. Sump pumpout should proceed with caution so as not to stir-up any Aroclor lying, on the bottom. After the sump has been returned to service, the outside water pumping can be discontinued. oSVJ STLCOPCB4090399 OPERATING INSTRUCTIONS AROCLOR SUMP GENERAL: . 'The sump maximum design rate of flow is 250 GPM and appears to be completely separating the second phase from the department effluent. The sump will hold 4000 gallons at a depth of around 3 1/2 feet. This is the maximum height of Aroclor the sump should have in it and should only occur after a major spill. In the north west comer there is a pump suction pit 18" x 18" x 24". This pit will hold. 34 gallons and should collect the Aroclor from the sloped floor. OPERATION: The pump pit should be pumped out as often as it fills up; ie. 34 gallons. Recom mend that the sump be pumped out once every two weeks. A small Randolph pump has been provided for this purpose. Collect the Aroclor and water in drums and haul to the dump. INSPECTION AND/OR MAINTENANCE: When it becomes necessary to pump the sump empty for inspection and/or repairs, the surrounding ground water must be pumped out first and kept out. A hole has been provided for this on hte northeast and southeast corners of the sump. A pump has not been provided, but the pump should stay in place and run continuously during the time the sump is empty. The sump pit should be emptied of Aroclor as much as possible. Sump pumpout should proceed with caution so as not to stir-up any Aroclor lying, on the bottom. After the sump has been returned to service, the outside water pumping can be . discontinued. dS\N 551984 STLCOPCB4090400 OPERATING INSTRUCTIONS AROCLOR SUMP GENERAL; The sump maximum design rate of flow is 250 GPM and appears to be completely separating the second phase from the department effluent. The sump will hold 4000 gallons at a depth of around 3 1/2 feet. This is the maximum height of Aroclor the sump should have in it and should only occur after a major spill. In the north- ,west comer there is a pump suction pit 18" x 18" x 24". This pit will hold 34 gallons and should collect the Aroclor from the sloped floor. . OPERATION: . The pump pit should be pumped out as often as it fills up; ie. 34 gallons. Recom mend that the sump be pumped out once every two weeks. A small Randolph pump has been provided for this purpose. Collect the Aroclor and water in drums and haul to the dump. INSPECTION AND/OR MAINTENANCE: When it becomes necessary to pump the sump empty for inspection and/or repairs, the surrounding ground water must be pumped out first and kept out. A hole has been provided for this on hte northeast and southeast corners of the sump. A pump has not been provided, but the pump should stay in place and run continuously during the time the sump is empty. The sump pit should be emptied of Aroclor as much as possible. Sump pumpout should proceed with caution so as not to stir-up any Aroclor lying on the bottom. After the sump has been returned to service, the outside water pumping can be discontinued. - . os-n56 . STLCOPCB4090401 OPERATING INSTRUCTIONS SUMP SKIMMER GENERAL: , The skimmer is to remove the floating phase of Aroclor and sludges. The skimmer .is temporarily mounted on a drum in the southeast comer of the sump. OPERATION: The skimmer barrel should be emptied once every 7 days during normal operation or when the barrel is full. The slurry in the barrel should be pumped into another barrel and hauled to the dump. . INSPECTION AND/OR MAINTENANCE: The oil level in the gear reducer should be checked every three days. Fill with worm gear oil or steam cylinder oils having a viscosity S.U.V. of 135-150 at 210F. Oil purchased at a service station may be used, SAE #140 recommended. Change after two weeks and every 6 to 8 months thereafter. Tube life expected to be 4 to 6 weeks, install Tygon R-4000, 3/4 IN O.D., 1/2 IN I.D., 50 ft. long. Install as shown. 55V*6 OS'N STLCOPCB4090402 INSERTING TUBING IN MODEL 610 BRILL SKIMMER A. Remove backplate, apply power and check direction of rotation. B. Squeeze hew tubing under tube guide lift up helical scraper@and wind in tubing. B. Rotate motor coupling until tubing passes under pressure wheel insert tube between inner and outer rows ofteeth on drive wheel up to the next pressure wheel direction until tubing is past second pressure wheel A. Continue to insert tubing past next pressure wheel by repeating previous instructions. CHECK LIST A. tubing is now in proper position on drive wheel and is ready to be placed on out rigger Tubing in proper opening at right of spout--under tube guide--through hel ical scraper--between inner and outer teeth of drive wheel--firmly held in place by four pressure wheels--place tubing in opening on right side, extend along outrigger through the guide yoke, and over the outboard wheel. Unit is now ready for operation ... be certain that motor will drive unjtjn proper direction. 1803 W. ROYALTON ROAD CLEVELAND, OHIO 44147 A DIVISION OF THE G. BRILL CO. CLEVELAND, OHIO DSW 551987 STLCOPCB4090403 OPERATING INSTRUCTIONS SUMP SKIMMER GENERAL; _ The skimmer is to remove the floating phase of Aroclor and sludges. The skimmer .is temporarily mounted on a drum in the southeast corner of the sump. OPERATION; The skimmer barrel should be emptied once every 7 days during normal operation or when the barrel is full. The slurry in the barrel should be pumped into another barrel and hauled to the dump. . INSPECTION AND/OR MAINTENANCE; The oil level in the gear reducer should be checked every three days. Fill with worm gear oil or steam cylinder oils having a viscosity S.U.V. of 135-150 at 210F. Oil purchased at a service station may be used, SAE #140 recommended. Change after two weeks and every 6 to 8 months thereafter. Tube life expected to be 4 to 6 weeks, install Tygon R-4000, 3/4 IN O.D., 1/2 IN I.D., 50 ft. long. Install as shown. DSW 551988 STLCOPCB4090404 INSERTING TUBING IN MODEL 610 BRILL SKIMMER A. Remove backplate, apply power and check direction of rotation. ' B. Squeeze new tubing under tube guide lift up helical scraperand wind in tubing. A. Place tubing between outside sprocket teeth on drive wheel B. Rotate motor coupling until tubing passes under pressure wheel insert tube between inner and outer rows ofteeth on drive wheel up to the next pressure wheel direction until tubing is past second pressure wheel A. Continue to insert tubing past next pressure wheel by repeating previous instructions. A. Repeat previous instructions. A.' Tubing is now in proper position on drive wheel and is ready to be placed on out rigger , CHECK LIST Tubing in proper opening at right of spout -- under tube guide--through hel ical scraper--between inner and outer teeth of drive wheel--firmly held in place by four pressure wheels--place tubing in opening on right side, extend along outrigger through the guide yoke, and over the outboard wheel. Unit is now ready for operation ... be certain that motor will drive unit in proper direction. 1803 W. ROYALTON ROAD CLEVELAND, OHIO 44147 A DIVISION OF THE G. BRILL CO. CLEVELAND, OHIO a959 pS'N 55 STLCOPCB4090405 OPERATING INSTRUCTIONS SUMP SKIMMER GENERAL;' _ ' The skimmer is to remove the floating phase of Aroclor and sludges. The skimmer is temporarily mounted on a drum in the southeast corner of the sump. OPERATION; . The skimmer barrel should be emptied once every 7 days during normal operation or when the barrel is full. The slurry in the barrel should be pumped into another barrel and hauled to the dump. . INSPECTION AND/OR MAINTENANCE; The oil level in the gear reducer should be checked every three days. Fill with worm gear oil or steam cylinder oils having a viscosity S.U.V. of 135-150 at 210F. Oil purchased at a service station may be used, SAE #140 recommended. Change after two weeks and every 6 to 8 months thereafter. Tube life expected to be 4 to 6 weeks, install Tygon R-4000, 3/4 IN O.D., 1/2 IN I.D., 50 ft. long. Install as shown. DSW 551990 STLCOPCB4090406 INSERTING TUBING IN MODEL 610 BRILL SKIMMER A. Remove backplate, apply power and check direction of rotation. ' B. Squeeze new tubing under tube guide lift up helical scraperand wind in tubing. B. Rotate motor coupling until tubing passes under pressure wheel insert tube between inner and outer rows ofteeth on drive wheel up to the next pressure wheel direction until tubing is past second pressure wheel A. Continue to insert tubing past next pressure wheel by repeating previous instructions. CHECK LIST A. Tubing is now in proper position on drive wheel CD and is ready to be placed on out rigger Tubing in proper opening at right of spout --under tube guide--through hel ical scraper--between inner and outer teeth of drive wheel--firmly held in place by four pressure wheels-- place tubing in opening on right side, extend along outrigger through the guide yoke, and over the outboard wheel. Unit is now ready for operation ... be certain that motor will drive unit .in proper direction. 1803 W. ROYALTON ROAD CLEVELAND, OHIO 44147 A DIVISION OF THE G. BRILL CO. CLEVELAND, OHIO STLCOPCB4090407