Document JkXxdqpwdNJ8okyYGa5ZO1oX

March 1,197 Parts List for Oil Burner Models 40 40CN 92C 92A HOW TO ORDER PARTS The following information must be specified: 1. Model Number of Burner (complete as shown above). 2. Unit in which burner is installed -- gallons per hour firing rate. 3. Number shown on Underwriters' label including any letter or letters used as a prefix. 4. Item No. (see Drawing). 5. Parts Identification (Description). 6. Additional Information (where required). NOTE: Prices available upon request. Minimum - invoice - SI0.00 F.O.B. Chicago, Illinois. AUTOMATIC BURNER CORPORATION 1823 Carroll Avenue Chicago, Illinois 60612 Form No. A-10 (3-1-75) PRINTED IN U.S.A. 05062 ITEM DESCRIPTION 1. Blower Housing Assembly 2. Air Inlet Band Assembly 3. 4. 5. 6. 7. 7A 7B. 8. 9. 9A. 9B. 9C. 10. 11. 12. Flexible Coupling Assembly.................... Fuel Pump................................................. Oil Line Assembly.................................... Blower Wheel Assembly.......................... Motor....................................................... Motor Junction Bax................................. Motor Junction Box Cover .................... Transformer.............................................. Drawer Adjusting Piste ........................... Drawer Adjusting Plate Slide ................. Rear Housing Cap.................................... Drawer Adjusting Plate .......................... Air Tube.................................................... Choke (End Cone).................................... Drawer Oil Pipe....................................... 12A. 13. Elbow........................................................ Static Pressure Disc................................. 14. 14A. 15. Spinner Assembly.................................... Shrouded Spinner Assembly.................... Electrode Support Assembly ................ 16. Electrode Rod Assembly ....................... 17. Nozzle Adaptor....................................... 18. Drawn Pipe Jam Nut.............................. 19. Electrode Support Bushing (2 required) . 20. Drawer Assembly (complete)................ 21. Burner Mounting Flange.......................... 21 A. 22. Burner Mounting Flange Gasket............. Burner Mounting Flange A TubeAssembly (welded) (not shown).............................. 23. Controls.................................................... 24. Cadmium Sulfide Cell............................... ADDITIONAL INFORMATION REQUIRED Complete Model Number Burner rating or specify number of openings, and width Mfg. data on fuel pump Mfg. data on fuel pump Mfg. data on fuel pump and air tube length. Dia., width A motor shaft dia. Mfg. nameplate data Mfg. nameplate data. Air tube length Air tube length 90* or straight oil pipe (see item 12) Air tube length (see Item 22 if welded fig.) Burner rating or ID. and number of vanes. Air tube length or length of pipe including node adaptor 90* or straight Burner rating or O.D. and amount of 3/8 dia. holes and specify full or half disc Burner rating or specify OD. of spinner Burner rating or specify type (tripod or vaned). If vaned specify width of vanes. Air tube length and buss bar or spring length Specify single or double nozzle Tube length, burner rating, or items 13 through 16 Specify die cast or steel - when steel must provide rough sketch Must provide rough sketch Specify item 21 information, air tube length and weld length (face of flange to end of air tube) Mfg. and mfg. data Mfg. and mfg. data 05063 o 05064 IMPORTANT BEFORE INSTALLING THIS BURNER,MAKE SURE THAT THE NOZZLE USED AND THE BURNER DIMENSIONS CORRESPOND TO THOSE LISTED FOR THE PROPER BOILER ON THE ACCOMPANYING DATA SHEET NO. HSK-I7I. NOZZLE AND BURNER SETTINGS AS SUPPLIED,IF DIFFERENT FROM SHEET NO. HSK171, MAY GIVE VERY POOR PERFORMANCE. r \ i 4 m 05066 IMPORTANT BEFORE INSTALLING THIS BURNER,MAKE SURE THAT THE NOZZLE USED AND THE BURNER DIMENSIONS CORRESPOND TO THOSE LISTED FOR THE PROPER BOILER ON THE ACCOMPANYING DATA SHEET NO. HSK-I7I. NOZZLE AND BURNER SETTINGS AS SUPPLIED,IF DIFFERENT FROM SHEET NO. HSK171, MAY GIVE VERY POOR PERFORMANCE. o f ( I\ r 05068