Document GmQoLq2dBVRKar1QdMpE49Yqx

NIBCO INC. ONE-YEAR LIMITED WARRANTY Applicable to NIBCO INC. Pressure Rated Ductile Iron, Industrial Ball & Butterfly, Alloy Iron, and Cast Steel Valves NIBCO INC. warrants each NIBCO pressure rated Ductile Iron, Industrial Ball & Butterfly, Alloy Iron, and Cast Steel valve to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase under normal use and service within limitations recommended by It. In the event any defect occurs which the owner believes is covered by this Warranty, the owner should immediately con tact NIBCO INC., either In writing or by collect telephone call, Attention; Valve Product Manager. The owner will be in structed to return said valve, at the owner's expense, to NIBCO INC. or an authorized NIBCO INC. representative for in spection. In the event said inspection discloses to NIBCO INC.'s satisfaction that said valve Is defective, It will be re placed or repaired at NIBCO INC.'s expense. Replacements shall be shipped free ol charge to the owner. THIS WARRANTY SPECIFICALLY EXCLUDES INCIDENTAL AND CONSEQUENTIAL DAMAGES OF EVERY TYPE AND DESCRIPTION RESULTING FROM ANY CLAIMED DEFECT IN MATERIAL OR WORKMANSHIP, INCLUDING BUT NOT LIMITED TO, PERSONAL INJURIES AND PROPERTY DAMAGES. Some states do not allow the exclusion or limitations of Incidental or consequential damages so these limitations may not apply to you. TO THE EXTENT PERMITTED BY LAW, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR TICULAR PURPOSE ARE LIMITED IN DURATION TO ONE (1) YEAR FROM THE TIME OF PURCHASE OF SAID VALVE. Some states do not allow limitations in how long an implied warranty lasts, so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. NIBCO f^SCO^JC PO SOX 1187 Elk hart, im .assis how to order State quantity, figure number and size for each valve you wish to order. See individual valve catalog pages for specific or special product designations. HOW MANY TO ORDER -- NIBCO valves are decimal packed for your conveni ence in handling, shipping and stock-keeping. Number in master carton varies with item. POLICY ON RETURNS TO FACTORY -- No NIBCO valves are to be returned without prior written agreement. Transportation must be prepaid. A 20% charge will be made to cover cost of rehandling ami reinspection. TECHNICAL ASSISTANCE -- Engineers, contractors, wholesalers or manufactui ers may obtain special or technical assistance from any factory representative of NIBCO. Write, wire or phone NIBCO Inc., Elkhart, Ind., for information regarding the sales representative for your area. Copyright 1985, NIBCO Inc.. Elkhart, Ind. The mformaiton presented in this catalog is correct at time of printing. NIBCO Inc. reserves the right io change design andfor material specifications without notice. Utho ml)'.* NIBCO000788 IM1BCO general index BALL VALVES Page One Piece ......................................... ......... 5-12 Two Piece................................... --.........13-21 Three Piece ...................... ............... ........22-35 BUTTERFLY VALVES .................. .... 36-52 ENGINEERING DATA INDEX ...................58 Flow Data ......................-.................... .... 64-65 Page Pipe Dimensions ........................ .....................70 Properties of Materials............................ 60-63 Specifications ...................................................59 OPTIONS AND ACCESSORIES INDEX.......... ................... 53 WARRANTY .............................................. 2 FIGURE NUMBER INDEX Fig. No. ball valves one piece Page Fig. No. ball valves three piece Page Fig. No. butterfly valves ductile iron Page T-560-BR-R-20 ........ ........... 6 S-590-Y ............. .................... 23 LD-2000 ..................... ..........38 T-560-BR-Y-20.......... ........... 6 T-590-Y............. .................... 23 WD-2000 ..................... ..........38 T-560-BR-R-66 ........ ........... T-560-BR-Y-66.......... ........... T-560-CS-R-25 ........ ........... 7 7 8 S-590-Y-66 ....... .................... 24 T-590-Y-66 ....... ................... 24 K-590-CS-R-25 ..................... 25 LD-2001 ..................... ..........39 WD-2001 ..................... ..........39 LD-2100 ..................... ..........40 T-560-CS-R-66 ........ ........... 9 T-590-CS-R-25 . .................. 25 WD-2100..................... ......... 40 T-560-S6-R-66......... ........... 10 K-590-CS-R-66 . ................... 26 LD-2101 ..................... ..........41 T-570-CS-R-25 ........ ........... 11 T-590-CS-R-66 . ................... 26 WD-2101 ..................... ..........41 T-570-CS-R-66 ........ ........... 12 K-590-S6-R-66 .. ...................27 LD-3010 ..................... ..........42 two piece S-580 ........................ ........... 14 T-580 ........................ ........... 14 S-580-66 ................... ........... 15 T-580-66 ................... ........... 15 S-580-BR-R-70 ........ ........... 16 T-580-BR-R-70 ........ ........... 16 T-580-CS-R-25 ........ ........... 17 T-580-CS-R-66 ........ ........... 18 T-580-S6-R-66 ......... ........... 19 S-585 ........................ ........... 20 T-585 ........................ ........... 20 S-585-66 ................... ........... 21 T-585-66 ................... ........... 21 T-590-S6-R-66 .. ................... 27 F-590-CS-R-25 .. ................... 28 F-590-CS-R-66 .. ................... 29 F-590-S6-R-66 .. ...................30 S-595-Y ............. ................... 31 T-595-Y............. ................... 31 S-595-Y-66 ....... ................... 32 T-595-Y-66 ........ ................... 32 K-595-CS-R-25 . ................... 33 T-595-CS-R-25 . ................... 33 K-595-CS-R-66 ..................... 34 T-595-CS-R-66 . ...................34 K-595-S6-R-66 .. ........... .. 35 T-595-S6-R-66 .. ................... 35 WD-3010..................... ..........42 LD-3011 ..................... ..........43 WD-3011 ..................... ..........43 LD-3110 ..................... ......... 44 WD-3110..................... ..........44 LD-3111 ..................... ......... 45 WD-3111 ..................... ..........45 LD-3*22 ..................... ......... 46 WD-3*22..................... ..........46 LD-3*33 ..................... ..........47 WD~3*33..................... ..........47 LD-3*44 ..................... ..........48 WD-3*44..................... ..........48 LD-0011 ..................... ..........49 WD-0011 ............................... 50 LD-0111 ...-............................ 51 WD-0111 ................................. 52 i NIBCO000789 MIBCO ball valves illustrated index Numerical Index Fig. No. Page T-560-BR-R-20............. 6 T-560-BR-Y-20............. 6 T-S60-BR-R-66............. 7 T-560-BR-Y-66 ....... 7 T-580-CS-R-25............. 8 T-560-CS-R-66 ....... 9 T-56Q-S6-R-66 ............. 10 T-S70-CS-R-25............. 11 T-570-CS-R-66............. 12 S-580 ............................ 14 T-580 ............................ 14 S-580-66 ....................... 15 T-580-66 ....................... 15 S-580-8R-R-70............. 16 T-580-BR-R-70............. 16 T-580-CS-R-25............. 17 T-580-CS-R-66............. 18 T-580-S8-R-66 ............. 19 S-585 ............................ 20 T-585 ............................ 20 S-S85-66 ........................ 21 T-585-66 ........................ 21 S-590-Y .......................... 23 T-590-Y .......................... 23 S-590-Y-66 ................... 24 T-590-Y-66 ................... 24 K-590-CS-R-25............. 25 T-590-CS-R-25............. 25 K-590-CS-R-66............. 26 T-590-CS-R-66............. 26 K-590-S6-R-66 ............. 27 T-590-S6-R-66 ............. 27 F-590-CS-R-25............. 28 F-590-CS-R-66............. 29 F-590-S6-R-66 ....... 30 S-595-Y .......................... 31 T-59S-Y .......................... 31 S-595-Y-66 ................... 32 T-595-Y-66 ................... 32 K-595-CS-R-25 ....... 33 T-595-CS-R-25............. 33 K-595-CS-R-66............. 34 T-595-CS-R-66............. 34 K-595-S6-R-66............. 35 T-595-S6-R-66 ............. 35 4 on Pi'ct Bull V.lv, ufMoSOOOtb.W.O.O. T-560.BR, CS. S6 Sitn Y.--Z" Thr*fJ end* One Piece Bar Stock Bali Valve up io 2000 ft. W.O.G. # T-570-CS Sizes W*-T Threaded Ends Two Piece Carbon Sleet Bali Valve up to 2000 ft. W.O.G. TWo Piece Bronze Balt Valve 4001b. W.O.G, T- or S-SIO Sizes 'h"`T T- or S-585 Sizes %**-V Threaded or Solder End* TWo Piece Stainless Sleet Bali Vaive up to 2000 ft. W.O.G. T- or S-SH-BR Sim V.*" Threaded or Solder Ends Three Piece Bronze 8a Valve 600 W.O.G. T-580-CS Size* Threaded Ends Three Piece Carbon Steel Ball Valve up to 1000 lb. W.O.G. Threaded Ends Three Piece Stainless Steel Balt Vaive T- or S-S9Q Size* T- or S-595 Size* W-2W* Threaded or Solder End* T-, K-, or F-590-CS Size* T-S95-CS Sizes '/."-r Threaded, Socket Weld, or Flanged End T-, K-, or F-590-S6 Sizes W-2" T-505-S6 Sizes W'~Z' Threaded. Socket Weld, or Flanged End Key to Bali Valve Figure Number System* 1 2.3.4 5.6 7 6.9 End Valve Designation Basic Material Seat Material Trim F -- Flanged X - Socket Weld S -- Solder T -- Threaded 560 -- One Piece Body Casting 570 -- One Piece Body Barslock 580/585 -- two Piece Body 590/505 - Three Piece Body 8R -- Bronze CS -- Carbon Steel S6-316SS V - Virgin TFE R -- Reinforced TFE B -- Bronze-Maly 20 -- Bronze 25 -- Carbon Steel 66 -- Stainless Steel 70 --Bronze/Chrome Plated Ball ` This key is a guittv tuiiy nrut not intended to mler that every valve will be produced that is contained in the key. NIBCO INC,. ELKHART, INDIANA N1BCO000790 NIBCO 560 SERIES NIBCO designed the T-560 line after intensive discussions with engi neers in processing, refining, and manufacturing plants. We asked what they considered most important in a one-piece ball valve, and what fea tures they wanted. We got the an swers. Now you've got the right ball valve for the job. And best of all, it's backed with NIBCO's unbeatable repu tation for quality, with on-time delivery and attractive pricing. Three body materials. To match your application needs, NIBCO offers the T-560 in three body materials-- bronze, carbon steel, and stainless steel. Bronze is ideal for service up to 600 psi; carbon and stainless steel One-piece ball valves will withstand pressures to 2000 psi in sizes Vi" through 2". Two seat materials. Glass rein forced TFE seats are standard on the carbon and stainless steel ball valves, for temperatures to 400 F at the valve's pressure rating. Virgin TFE seats, with 600 psi and 366 F rating are standard on the bronze ball valves and offer excellent sealing with low line pressure. One-piece body. The one-piece construction of the T-560 gives you an important safety advantage: it eliminates the chance of accidental disassembly when downstream pip ing is being turned. Of course, it also greatly reduces the chances of a leak. Standard features. A hole drilled in the ball stem slot allows the pres sure to equalize between the body cavity and the ball bore when the valve is in the full open position. This eliminates the possiblity of damaging or blowing out the seat should en trapped fluid expand rapidly. A stainless steel spring washer grounds the stem to the valve body to prevent static electric discharge on all T-560 valves. No stem leakage, even when ' ^ handle is removed whiid ;Vaive is in service. Separate steel nuts secure both the packing and tie handle. . . .... .' - f *-t /r " , Reinforced TFE packing with . . Belleville 'washer- assures leak-free T seal on. cool-down and as packing p"wears.' ^ '""-'V V . yy `i i-r^ .-"..-v-.-i '*' The insert, which holds the inter?^-^.,:^^ nal assembly in position, is shout- i . IS;: Seat: riKgrare; ' 'T.v.nf^v =-T-rv- ` ;u ' Lever handle \s standard-^-jTiade". T. . of hardened ,,.r, phate' finish''$n7d:>iijsu"Tatfh^pIa^ ; ' - grip. v; T-Sn` \~ - ' 5^ >y|sV ? Tndependent^a'rtfehed-steel^:^ ' :;i;|T.;..."^stops all(^bnfy^^^jfuji^pReh:to:;'. ti.terialsi/'virglrTJFE,* " ,*1 &T;:g!ass-reihforeed^TFE%.;:TTV H >: aanndd bhrrnoon7zPp--mmonllyv-T+ * ` , filled TF- Erfex';:t>- ^ if -v,-Blowout-proof ? stem. Reinforced TFE thrust washer creates 'fi an internal :seal.;;\.'>! 5, -that improves j.; pressure increases._ ";; Balls'are " * fully machined tor i ish, and., individuallyTil assure optimum seal t seat life, and low t 1T.,'to ; MU I -- ' ..... Mi.- ... . - .. ` 7. ................ <<$ i l*2fIkX: NIBCO000791 IMIBCO bronze ball valves One Piece Body * Blowout-Proof Stem * Bronze Trim 600 lb. WOG Federal Specifications: WW-V-35, Type II, Class A, Style 3 MATERIAL LIST PART 1. Handwheel Not SPECIFICATION Zinc Plated Steel 2, Identification Plata Aluminum 3. Handle Zinc Plated Steel. Plastisol Coated 4. Packing Nut Zinc Plated Steel S. Belleville Washer Zinc Plated Steel 6. Travel Stop Zinc Plated Steel 7. Pack Gland Brass. ASTM 8-16 8. Packing Reinforced TFE 9. Grounding Washer Stainless Steel, ASTM A-167 Type 304 10. Thrust Washer Reinforced TFE 11. Stem Bronze. ASTM B-371 Alloy 694 12. Ball* Bronze. ASTM 8-584 Alloy 844 13. Seat Ring (2) TFE (V): Reinforced TFE (Rt 14. Body Insert Bronze. ASTM 8-5B4 Alloy 844 15. Body Bronze, ASTM B-584 Alloy 844 Ball Material on V. W. and V sizes is ASTM B-16. DIMENSIONS -- WEIGHTS -- QUANTITIES Appro*. Master Net WL Carton Size A B c 0 E F G Lb. Oty. 27, 1'V IV. %4 1%! 10-24 .6 SO 7. 2% I'Va 174 V. 4 1 'Is 10-24 .6 50 'h 2/ 1'V IV. %4 1?/ai 10-24 .6 50 V. 2!7 1V 'h 4 1%. 10-24 .8 50 1 3fe 2 V. 4 Wit 1 "In V.-20 13 30 IV. 1 'Vis 2V.< u/. 4'Vis Vh 'A-20 2.0 20 Vh 4 2'/is 2s/is 1 6% IV. '/.-20 2 4'/* Z'h, 2% IV. 6% 2>/ V.-20 2.8 4.3 20 10 T-560-BR-Y-20 threaded TFE Seats and Seals with Bronze trim T-560-BR-R-20 threaded Reinforced TFE Seats and Seals with Bronze trim NOTE: For specific pressure/temperature relationships refer to page 67. 6 NIBCO INC., ELKHART, INDIANA NIBCO000792 MIBCO bronze ball valves One Piece Body Blowout-Proof Stem 316 S.S. Trim 600 lb. WOG Federal Specifications: WW-V-35, Type II, Class A, Style 3 T-560-BR Series NPT x NPT MATERIAL LIST PART SPECIFICATION 1. Handwheel Nut Zinc Plated Steel 2. Identification Plata Aluminum 3, Handle Zinc Plated Steel, Plastisol Coated 4. Packing Nut Zinc Plated Steel 5. Belleville Washer Zinc Plaled Steel 6. Travel Stop Zinc Plated Steel 7. Pack Gland Stainless Steel. ASTM A-276 Type 316 8. Packing Reinforced TFE 9. Grounding Washer Stainless Steel. ASTM A-167 Type 304 10. Thrust Washer Reinforced TFE 11. Stem Stainless Steel. ASTM A-276 Type 316 12. Ball Stainless Steel. ASTM A-276 Type 316 13. Seat fling (2) TFE (Vi: Reinforced TFE |R) 14. Body Insert Bronze, ASTM B-584 Alloy 844 15. Body Bronze. ASTM B-584 Alloy 844 DIMENSIONS - WEIGHTS -- QUANTITIES Approx. Master Net Wt Carton Size A 8 C 0 E F G Lb. qty. V* 2V, 1'*/J! IV, V, 4 17 10-24 .6 50 >!, 2s'. 1 "hi IV, V, 4 17 10-24 .6 50 2%; 1 "ht 1% % 4 T/ 10-24 .6 50 su 2'/ VU 1/k 'h 4 17m 10-24 .8 50 1 Th: 1JN 2 V, 4>V* 1 Vi-20 1.3 30 IV. 3'>h 1'V# 2% ah 4"/n 17, '/.-2Q 2.0 20 IV, 4 2V 2Vu 1 61/. m >/.-20 2.8 20 2 4%. 2%, 2?k 1'/, 6% 2'h 'A-20 4,3 10 NOTE: For specific pressure/temperature relationships refer lo page 67. T-560-BR-Y-66 threaded TFE Seats and Seals with S.S trim T-560-BR-R-66 threaded Reinforced TFE Seats and Seals with S.S trim \ i NIBCO INC., ELKHART, INDIANA 7 NIBCO000793 carbon steel ball valves One Piece Body Blowout-Proof Stem C.S, Trim Up to 2000 lb. WOG # NIBCO000794 MIBCO carbon steel ball valves One Piece Body Blowout-Proof Stem * 316 S.S. Trim Up to 2000 lb. WOG Federal Specifications: WW-V-35, Type II, Class D, Style 3 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Identification Plate Aluminum 3. Handle Zinc Plated Steel. Plastisol Coated 4. Packing Nut Zinc Plated Steel S. Belleville Washer Zinc Hated Steel 6. Travel Stop Zinc Plated Steel 7. Pack Gland Stainless Steel. ASTM A-276 Type 316 a Packing Reinforced TFE 9. Grounding Washer Stainless Steel, ASTM A-167 Type 304 10. Thrust Washer Reinforced TFE 11. Stem Stainless Steel. ASTM A-276 Type 316 12. Ball Stainless Steel. ASTM A-276 Type 316 13. Seat Ring 0 Reinforced TFE 14. Body Insert Carbon Steel. ASTM A-108 Type 12114. Phosphale Coated IS. Body Carbon Steel. ASTM A-216 GR WCB. Phosphate Coated T-560-CS-R-66 threaded Reinforced TFE Seats and Seals with S.S. trim DIMENSIONS -- WEIGHTS -- QUANTITIES Size A V* 2V, J. 2* fl c 1"/ 1% 1'Vjj 1% DE %4 V. 4 FG 1'/ 10-24 1%! 10-24 Approx. NelWL Lb. .6 .6 Master Carton ODf. 50 50 2<V* 1/ji 114 % J/, 2nU 1*.- P>ln % 4 4 Vht 10-24 Vht 10-24 .6 .8 SO 50 1 33* 1/ 2 ? 4"/k 1"/ Vi-20 1.3 30 IV, 3%, Wr 2V ah 4>V 17! Vi-20 2.0 20 l'*'z 4% 2li 2S/,! 1 65/. 1*/. A-20 2.8 20 2 4"/.; 2'U Vk 1'A 6% 2'/* '/.-2a 4.3 to NOTE: For specific pressure/temperature relationships refer to page 67. NIBCO INC.. ELKHART, INDIANA 9 NIBCO000795 stainless steel ball valves One Piece Body * Blowout-Proof Stem *316 S.S. Trim 2000 lb. WOG NIBCO000796 MIBCO carbon steel ball valves One Piece Barstock Body Blowout-Proof Stem * C.S. Trim %"-1" 2000 ib. WOG 1W'-2" 1500 lb. WOG T-570-CS Series NPT x NPT Federal Specifications: WW-V-35, Type II. Class D, Style 3 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Identification Plate Aluminum 3. Handle Zinc Plated Steel. Ptastisol Coated 4. Packing Nut Zinc Plated Steel 5. Belleville Washer Zinc Plated Steel 6. Pack Gland Stainless Steel ASTM A-276 Type 304 7. Packing Reinforced TFE 8. Thrust Washer Reinforced TFE 9. Stem Carbon Steel ASTM A-108 Type 12L14. Nickel Plated 10. Ball Carbon Steel ASTM A-108 Type 12114. Hard Chrome Plated 11. Seal Ring (2) Reinforced TFE 12. Body Insert Carbon Steel ASTM A-108 Type 12L14, Phosphate Coated 13. Body Carbon Steel ASTM A-108 Type 12L14, Phosphate Coaled *m T-570-CS-R-25 threaded Reinforced TFE Seats and Seals with C.S. trim DIMENSIONS -- WEIGHTS -- QUANTITIES Size A 8 ft m 1ft ft 2ft 1% C IV. 1% 0E ht 3% % 3% Approx. NetWl Lb. .5 .8 Master Carton Qty. 80 80 1 3% 1% 2ft IV. n 1% 2% v 5ft ft 5ft 1.4 2.4 40 8 1ft 4 2 2ft 1 6v? 2 47; 2ft 3 1ft 6ft 3.3 5.3 8 3 NOTE: For specific pressure/temperature relationships refer to page 67. NIBCO INC., ELKHART. INDIANA 11 NIBCO000797 carbon steel ball valves One Piece Barstock Body Blowout-Proof Stem * 316 S.S, Trim Va"'1" 2000 lb. WOG 1500 lb. WOG Federal Specifications: WW-V-35, Type II, Class D, Style 3 MATERIAL LIST part SPECIFICATION 1. Handle Nut Zinc Plated Steel - 2. Identification Plate Aluminum 3. Handle Zinc Plated Steel. Plastisol Coated 4, Packing Nut Zinc Plated Steel 5. Belleville Washer Zinc Rated Steel 6. Pack Gland Stainless Steel. ASTM A-27B Type 304 7. Packing Reinforced TFE 8. Thrust Washer Reinforced TFE 9. Stem Stainless Steel. ASTM A-278 Type 316 10. Ball Stainless Steel. ASTM A-276 Type 316 11. Seat Ring 12) Reinforced TFE 12. Body Insert Carbon Steel, ASTM A-108 Type 12114. Phosphate Coated 13. Body Carbon Steel. ASTM A-108 Type 12L14. Phosphate Coated T-57Q-CS-R-66 threaded Reinforced TFE Seats and Seals with S.S. trim DIMENSIONS -- WEIGHTS -- QUANTITIES Size A B ft 2V 1V ft m IV# C m i% 0E Ta 3% % Approx. HetWt Lb. 5 Master Carton Oty. 80 80 1 3V 1% 2ft '% 5ft 1.4 40 IV. 3s/ 1% 2* 57. 2.4 8 1ft 4 2 2% 1 6ft 3.3 8 2 4ft 2ft 3 1*A 6ft 5.3 8 NOTE: For specific pressure/temperature relationships refer to page 67. 12 NI8CO INC., ELKHART, INDIANA NIBCO000798 NIBCO 580 SERIES NIBCO's product philosophy is to Two-piece WOG in sizes V4" through 2". design, produce, and market the right < valve for the application intended. In ball valves Conventional port. The 580 line, offered in sizes from W' through 2" doing this, NIBCO's customers enjoy and rated at 125 SWP/400 WOG, long-term dependable service at pric three port sizes and three pressure has a conventional port that will ing that is realistic and very competi ratings. accomodate the majority of ball valve tive. NIBCO's figure number 580 and Full port. The 585, rated at 150 applications. 585 bronze valves are consistent in SWP/400 WOG in sizes from 14" Federal Specification compli conforming to this view. through 1", has a full port, for those ance. NIBCO ball valves meet Fed The result is a bronze two-piece, applications with critical flow require eral Specification WW-V-35, and are I end-entry ball valve that has a proven ments. available with either threaded or history of quality performance in a Standard port. The 580-BR line solder ends. wide range of residential, commer is a heavier duty, ruggedly construc The valves that do the job--the cial, and industrial applications. ted bronze body with blow-out proof lightweight 580, 580-BR and 585. In order to accommodate the stem and chrome plated ball. These Check the features below and see consumer or engineer, NIBCO offers valves are rated at 150 SWP/600 why NIBCO offers you more value. iZinc^chjfqmata^lnighed . V... v. . , 1.PC --a r - - . |||T rZinc-p|i^^8eJ;'h^^bniit: for P^'corrosion i^isfonc,.Handlenut musp. . ft-fbe held inplaijrfj^^1s,rerii6ved.*f.. *. ' IV- - . , ..,...,.... ill iustable Tonmore life th&F ponadjust- %*j i^ableTFr6^des&itt;TTT-,^U^^ NIBCO000799 NIBCO bronze ball valves Two-Piece Body Conventional Port Bronze Trim Blowout-Proof Stem 125 PSI Saturated Steam 400 PSI Non-Shock Cold Water, Oil or Gas Federal Specifications: WW-V-35, Type II, Class A, Style 3 MATERIAL LIST PAST SPECIFICATION 1, Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel. Plastisol Coated 3. Packing Gland Brass ASTM 8-16 4. Packing TFE Impregnated Asbestos 5. Stem Silicon Bronze ASTM 0-371 Alloy 694 6. Ball* Cast Red Bronze ASTM B-584 Alloy 845 7. Seat Ring (2) TFE 3, Body Cast Red Bronze ASTM B-584 Alloy 845 9. Body End Piece Cast Red Bronze ASTM B-584 Alloy 845 "Ball Material on V. and V sizes is ASTM 8-16. t S-580 Copper x Copper 14 DIMENSIONS -- WEIGHTS -- QUANTITIES Approx. Master Dim. A Dim. Dim. C Dim. D Net WL . Cta Size T-580 S-580 B T-580 S-580 Pori T-580 S-580 Oty. '/? 2 1*/ I8/* 4% 4/ 7 ,5 .5 100 % 2% 1!%j 5 57* 7i .7 7 100 1 2% 3'/ 2% 67,s 6 1.3 1.3 50 1% 2ln 3% 27* 6"In 67* i 1.9 1.8 25 1% 37, 47, 2aI 8>/,s 8>* i% 2.9 3.0 10 2 47* 5'fo 37* 87. 9V, IVs 4.5 4.8 10 t Designed to be soft soldered into lines using solders with the melt ing point not exceeding 450F. Higher temperature solders will dam age the seat material. NOTE: For specific pressure/temperature relationship refer to page 67. NIBCO INC., ELKHART, INDIANA TFE Seats and Seals t S-580 solder TFE Seats and Seals NIBCO000800 IMIBCO bronze ball valves Two-Piece Body Conventional Port * 316 S.S. Trim 125 PSt Saturated Steam 400 PSt Non-Shock Cold Water, Oil or Gas Blowout-Proof Stem t* Federal Specifications: WW-V-35, Type II, Class A, Style 3 i MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel. Ptastisol Coated 3. Packing Gland Brass ASTM B-16 4. Packing TFE impregnated Asbestos S. Stem Silicon Bronze ASTM B-371 Alloy 694 6. Bar Cast Red Bronze ASTM 8-584 Alloy 845 7. Seal Ring (2) TFE 8. Body Cast Red Bronze ASTM B-584 Alloy 845 9. Body End Piece Cast Red Bronze ASTM B-584 Alloy 845 Ball Material on W, and */<' sizes is ASTM B-16. DIMENSIONS -- WEIGHTS -- QUANTITIES Approx. Mister Dim. A Dim. Bim.C Dim. 0 NelWt . On. Size T-S80 S-580 B T-580 S-580 Port T-580 S-580 Oiy. ft 2 1% 17* 47i 4/ % .5 .5 100 7. 27 2%4 F7 5 57* ft .7 .7 100 1 27. 37 27* 6V* 67 7- 1.3 1.3 50 1% 3'7 3V 27* 6"/ 67* 1 1.9 1.8 25 1% 344 4 ft 2/* 87* 8'7 174 2,9 3.0 10 2 47* 5'hi 3'/* m 9'/. 1ft 4.5 4.8 10 t S-580 Copper x Copper tDesigned to be soft soldered into lines using solders with the melt ing point not exceeding 45Q'F, Higher temperature solders will dam age the seat material, NOTE: For specific pressure/temperature relationship refer to page 67. T-580-66 threaded TFE Seats and Seals with S.S. trim t S-580-66 solder TFE Seats and Seals with S.S. trim NIBCO INC., ELKHART, INDIANA 15 NIBCO000801 IMIBCO bronze ball valves Two-Piece Body Standard Port Bronze Trim Chrome Plated Ball Blowout-Proof Stem ISO PSI Saturated Steam 600 PSI Non-Shock Cold Water, Oil or Gas Federal Specifications: WW-V-35, Type II, Class A, Style 3 T-580-BR NPT x NPT t S-580-BR Copper x Copper 16 PART 1. Handle Nut z Handle a Stem 4. Packing Gland 5. Packing a Thrust Washer 7, Body End Piece 8. Seat Ring (2) a Ball 10. Body MATERIAL LIST SPECIFICATION Zinc Plated Steel Zinc Plated Steel. Ptastisol Coated Brass, ASTM B-16 Brass, ASTM B-16 TFE Reinforced TFE A'-'/i" Brass. ASTM 8-16 >*"? Cast Bronze, ASTM B-584 Alloy 844 Reinforced TFE Brass. ASTM 8-16. Hard Chrome Plated Cast Bronze. ASTM B-584 Alloy 844 T-580-BR-R-70 threaded Reinforced TFE Seats and Seals with Chrome Plated Ball DIMENSIONS -- WEIGHTS -- QUANTITIES dim. A Dim. Dim. Dim. as Master On. Oty. She T-5B0-BB S-SflO-BB 8 c 0 T-580-8R S-580-88 T-580-BR S-580-8R v 2%. - 1'V.s V, 3 .50 - 120 % 2% - I'Vis V, 3 .46 - 120 % 2%, 1!v IV, <h 3 .60 .63 90 % 2h 2'/ Vta !% 33A 1.25 1.32 30 - 80 30 1 3% 3 2'hi Vs 3% 1.72 1.80 30 15 5'4t`/ 3,s/ 2'V# 2>'hi 1 3.08 3.17 15 12 Vk 4'/. 2% 2V. IV. 5'h 4.00 3.91 15 9 2 mi 3% 3'hi 1*4 5<h 5.76 5.44 6 6 f S-580-BR-R-70 solder Reinforced TFE Seats and Seals with Chrome Plated Ball tDesigned to he soft soldered into lines using solders with the melt ing point not exceeding 450"F. Higher temperature solders will dam age the seat material. NOTE: For specific pressure/temperature relationship refer to page 67. NIBCO INC., ELKHART, INDIANA NIBCO000802 NIBCO carbon steel ball valves Two Piece Barstock Body Biowout-Proof Stem C.S, Trim W'-l" 2000 lb, WOG 1W'-2" 1500 lb. WOG Federal Specifications: WW-V-35, Type II, Class D, Style 3 T-580-CS Series NPT x NPT MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Identification Plate Aluminum 3. Handle Zinc Plated Steel. Plastisol Coated 4. Packing Nut Zinc Plated Steel 5. Belleville Washer Zinc Plated Steel 6. Pack Gland Stainless Steel ASTM A-276 Type 304 7. Packing Reinforced TFE 8. Thrust Washer Reinforced TFE 9. Stem Carbon Steel ASTM A-108 Type 12L14, Nickel Plated 10. Balt Carbon Steel ASTM A-108 Type 12114, Hard Chrome Plated 11. Seat Ring {2) Reinforced TFE 12. Body End Piece Carlton Steel ASTM A-108 Type 12114. Phosphate Coaled 13. Body Carbon Steel ASTM A-108 Type 12114, Phosphate Coated DIMENSIONS -- WEIGHTS -- QUANTITIES Approx. Mister NetWt Carton Size A B C 0 E Lb. Qty '!> 2 1 1% % 3% .5 80 44 2 1 144 % .5 80 '/> 244 1V 1% % 3% .8 80 V. 2% 1% Z% <% 5% 1.4 40 1 3* 1% 2% 'ft 5V4 2.4 8 IV. 3>A 1'/. 2% 1 6V4 3.3 8 IVi 444 244 3 1'A 6% 5.3 8 2 4"fc 2% 3V 144 7T* 7.9 8 NOTE: For specific pressure/temperature relationships refer to page 67. NIBCO INC., ELKHART, INDIANA T-580-CS-R-25 threaded Reinforced TFE Seats and Seals with C.S trim 17 NIBCQ000803 rvjiBco carbon steel ball valves Two Piece Barstock Body Blowout-Proof Stem 316 S.S. Trim V"-1" 2000 lb. WOG 1W-2" 1500 lb. WOG NIBCO000804 ' |; I' ftsi* . W t. . ft v;: K it). NiBca stainless steel ball valves Two Piece Body Blowout-Proof Stem 316 S.S. Trim V"-1" 2000 lb. WOG 1V"-2" 1500 lb. WOG Federal Specifications: WW-V-35, Type II, Class C, Style 3 MATERIAL LIST FART SPECIFICATION 1. Handle Nut Stainless Steel, ASTM A194 GR8 (304) 2. Identification Plate Aluminum 3. Handle Stainless Steel. ASTM A-167 Type 304. Plastisoi Coated 4. Packing Gland Stainless Steel, ASTM A-276 Type 316 5. Packing Reinforced TFE 6. Thrust Washer Reinforced TFE 7. Stem Stainless Steel. ASTM A-276 Type 316 8. Ball Stainless Steel. ASTM A-276 Type 316 9. Seat Ring (2) Reinforced TFE 10. Body End Piece Stainless Steel. ASTM A-276 Type 316 (W-H Stainless Steel. ASTM A-351 Gr, CF8M (1 r-rj 11. Body Stainless Steel, ASTM A-351 GR. CF8M DIMENSIONS -- WEIGHTS -- QUANTITIES Approx. Mister Net Wt. Carton Size A 8 C 0 E f G H Lb. Oty. '/. 2 1 17, m, Vi 17, 10-24 .5 80 V, 2 1 m mi 'k 17, 10-24 .5 80 7, 2V 17, m, ''la 3'7 y. 2"ta 1U/l! 2V "/ 4"/i \h % 17, 10-24 1 10-24 .8 1.4 BO 40 i 3'hi 17, 27* 7, 4'V 7, 1>A 10-24 2.4 8 17. 3'V 1% 2% 1 6"/ '7* Vk 7.-20 3.3 8 i 'h 4'h 2%, 2"/ 17. 2 V'h, 27., 3% 1% 6n/ % 6"/,, Vk 7.-20 Vk 7,-20 5.3 7.9 8 8 T-580-S6-R-66 threaded Reinforced TFE Seats and Seals with S.S. trim NOTE: For specific pressure/temperature relationships refer to page 67. NIBCO INC., ELKHART, INDIANA 19 NIBCO000805 IMIBCO bronze ball valves Two-Piece Body * Full Port Bronze Trim Blowout-Proof Stem ISO PS1 Saturated Steam 400 PS) Non-Shock Cold Water, Oil or Gas % Federal Specifications: WW-V-35, Type 11, Class A, Style 3 T-580 NPT x NPT t S-580 Copper x Copper MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel. Ptastisol Coated 3. Packing Gland Brass ASTM 8-16 4. Packing TFE Impregnated Asbestos 5. Stem Silicon Bronze ASTM 8-371 Alloy 694 6. Ball* Cast Red Bronze. ASTM B-584 Alloy 845 7. Seat Ring (2) TFE 8. Body Cast Red Bronze ASTM B-584 Alloy 845 9. Body End Piece Cast Red Bronze ASTM B-584 Alloy 845 `Ball material on 'A*. >4", and r sizes is ASTM 8-16. DIMENSIONS -- WEIGHTS -- QUANTITIES Approx, Master Dim, A Dim. Dim. C Dlm.O NetWt . Cln. Size T-585 S-585 B T-585 S-585 Pert T-5B5 S-585 Qty- V* 2 I7i 1% 4% 47, 3k* .6 .5 100 h2 17, 17,s 47, 47, % .6 .5 100 'h 2V, 27, 1H 5 5 'A .6 .6 100 7, n 3 2% 6 m 7, .9 .9 50 1 3% 3V* 27* 6'h 1 1.8 1.6 50 -s/i6 on S-58S tDesigned to be soft soldered into lines using solders with the melt ing point not exceeding 450T. Higher temperature solders will dam age the seat material. NOTE: For specific pressure/iemperature relationship refer to page 67. T-585 threaded TFE Seats and Seals f $-585 solder TFE Seats and Seals 20 NIBCO INC.. ELKHART. INDIANA NIBCO000806 A'. ` NIBCO bronze ball valves Two-Piece Body Full Port Blowout-Proof Stem 316 S.S. Trim 150 PSI Saturated Steam 400 PSI Non-Shock Cold Water, Oil or Gas T-580 NPT x NPT t S-580 Copper x Copper Federal Specifications: WW-V-35, Type II, Class A, Style 3 PART t. Handle Nut 2. Handle 3. Packing Gland 4. Packing 5. Stem 6. Ball 7. Seat Ring (2) 8. Body 9 Body End Piece MATERIAL LIST SPECIFICATIOM Zinc Plated Steel Zinc Waled Steel, Plastisol Coated Brass ASTMB-16 TFE Impregnated Asbestos Stainless Steel, ASTM A-2T6 Type 316 Stainless Steel. ASTM A-276 Type 316 TFE Cast ted Bronze, Copper Alloy 845 Cast Red Bronze, Copper Alloy 845 DIMENSIONS -- WEIGHTS -- QUANTITIES Approx. Master Dim. A Dim. Ofm. C Bim.D MetWL . Ctn. Size r-sas S-585 8 T-5B5 S-585 Pert T-585 S-585 Oty. V. 2 1% 1'/* 4% 4% V .6 .5 100 %2 1% 1*/.* 4'A 4V. .6 .5 100 'h 2V, 2V. m 5 5 % .6 .6 100 % 2Vi 3 2V# 6 W* % .9 .9 50 1 3% m 2'U m m 1 1.8 1.6 50 /* on S-585 tOesigned to be soft soldered into lines using solders with the melt ing point not exceeding 450F. Higher temperature solders will dam age the seat material. NOTE: For specific pressure/temperature relationship refer to page 67. T-585-66 threaded TFE Seats and Seals with S.S. trim f S-585-66 solder TFE Seats and Seals with S.S. trim NIBCO INC., ELKHART, INDIANA 21 NIBCO000807 NIBCO Vv ' -/.Tj. The NIBCO 590 and 595 Series Ball Valves are based on a proven, versatile three-piece design that com bines superior performance charac teristics with fast, economical in-line maintenance. These valves offer swing-out accessibility that makes them ideal for commercial and indus trial installations where frequent clean ing and seal replacement are necessary. The 590 Series has a conven tional port in both threaded and solder ends. They are available in sizes from 1 Vi" through 3". For full flow, specify the 595 Se ries, with full port. Available in sizes from Vi" through 2Vz\ these valves of fer unobstructed flow for applications 590 SERIES Three-piece ball valves that require optimum flow conditions. Both valves meet the require ments of Federal Specification VWVV-35, and are rated up to 1,500 psi. Swing out design. The swingout three-piece body construction allows for easy in-line valve disas sembly to clean, service, or replace seals without the high labor costs involved in tearing down and remak ing pipe connections. During installation, the swing-out design allows the ends to be threaded or soldered into place separately, with the center section installed lator This prevents any damage to the TFE seats that might occur during solder ing, brazing or welding. The body can be pivoted to the most convenieni position. Interchangeable ends. NIBCO 590 and 595 parts in sizes 1" and larger are interchangeable. By interchang ing valve ends, for example, you can make a valve that reduces or in creases pipe size through the valve. A 1 Vi" end can be substituted tor a 1 '/>" end, thus making a 1 Vi" x 1W' valve. A small part inventory gives you a com plete selection of conventional and full port parts and bodies in both threaded and solder ends. i ,i**v .> fcij-.Handle..is-'zinc-'chromate-plated , f.Tist'eer for "corrosion' resistance', and-- forced TFE and can be adjusted on-line l^jamply by tightening the nut.. l-fe-: -'r. ' :` jVjiTT,;TTie stem is blowout-proof. It's.in- - ff?serted ' 'irom iwithin -'the valve, and - l^fshbufder'prevents rts removal from the ; ^outside....T' ' 1* ' ' NIBCO000808 bronze ball valves Three Piece Body Blowout-Proof Stem Conventional Port Bronze Trim 150 PSI Saturated Steam 600 PSI Non-Shock Cold Water, Oil, or Gas Federal Specifications: WW-V-35, Type II, Class A, Style 1 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel, Plasllsol Coated 3. Packing Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5. Travel Stop Zinc Plated Steel 6. Stem Silicon Bronze ASTM B-371 Alloy 694 7. Pack Gland Brass ASTMB-16 a. Body Bronze ASTM B-584 Alloy 844 9. Packing Reinforced TFE 10. Body Ends Cast Bronze ASTM B-584 Alloy 844 11. 0-Ring Seal (2) Fluorocarbon Rubber 12. Seat Ring (2) TFE 13. Bail Cast Bronze ASTM B-584 Alloy 844 14. Ground Device Stainless Steel. 316 SS 15. Thrust Washer Reinforced TFE 18. Body Bolts Zinc Plated Steel 17. Body Nuts Zinc Hated Steel T-590-Y threaded TFE Seats with Bronze trim r S-59Q-Y Copper x Copper DIMENSIONS -- WEIGHTS -- QUANTITIES Hem. Din. A Dim. A Size Threaded Selder Dimension! 8. C, 0, and E same lor solder and threaded ends BC0 E Dim. F Solder Approx. Weight Threaded Approx. Weigh! Solder Ctn. Oty. H. 3'V, 3!'ln 2% 1 2% 4*'/ Wh 3.2 2.9 10 V; 4y,. 4*A 2"/ IV* 37. B"h 2>/.t 4.5 35 10 7 4*V** 5V. 3 116 3%i 6"/.. 2'/n 6.4 5.7 6 t; 6V..- 614 4 2 3"/.. 6"/ 3Vi. 11.8 10.2 5 .1 6:7,.- 7'/., 5 216 4"/ 8 4% 18.0 16.0 4 NOTE For spociflc pressure/temperature relationships refer to page 67. S-590-Y solder TFE Seats with Bronze trim NIBCO INC., ELKHART, INDIANA 23 NIBCO000809 IMIBCO bronze ball valves Three Piece Body Blowout-Proof Stem Conventional Port 316 S.S. Trim 150 PSI Saturated Steam 600 PSI Non-Shock Cold Water, Oil, or Gas T-590-Y NPT x NPT Federal Specifications: WW-V-35, Type II, Class A, Style 1 MATERIAL LIST PART SPECIFICATION f. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steal, Plastisol Coated 3. Packing Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5. Travel Stop Zinc Plated Steel 6. Stem Stainless Steel ASTM A-276 Type 316 7. Pack Gland Brass ASTM B-16 8. Body Bronze ASTM B-584 Alloy 844 9. Packing Reinforced TFE 10. Body Ends Cast Bronze ASTM B-584 Alloy 844 11. 0-Ring Seal (2) Fluorocarbon Rubber 12. Seat Ring (2) TFE 13. Bali Stainless Steel ASTM A-276 Type 316 14. Ground Device Stainless Steel. 316 SS 15. Thrust Washer Reinforced TFE 16. Body Bolts Zinc Plated Steel 17. Body Nuts Zinc Plated Steel T-590-Y-66 threaded TFE Seats with S.S. trim S-590-Y Copper x Copper DIMENSIONS -- WEIGHTS -- QUANTITIES Non, Dim. A Din. A Size Threaded Solder Dimensions 8. C.D. and E same for solder and threaded ends BC0E Dim. F Solder Appro*. Appro*. Weight Weight Threaded Solder Ctn. Oty. I'/i 3"/ 3% 2'h 1 2'h 4!'fe t*hi 3.2 2.9 10 Vh 4%* Vh 2"hi 1'/. 3% 6"/ 27,< 4.5 3.9 10 2 4A, 5V< 3 Vh 3"ht 6"/ 2/ 6.4 5.7 6 i'h 6'/ 67. 4 2 3"/.. 6"/n 37,, 11.8 10.2 5 3 6"/ 77., 5 2'h 4 "h 8 4'/i 18.0 16.0 4 S-590-Y-66 solder TFE Seats with S.S. trim NOTE: For specific pressure/temperature relationships refer to page 67. 24 NIIBCO INC., ELKHART, INDIANA NIBCO000810 IMIBGO carbon steel ball valves Three Piece Body Blowout-Proof Stem Conventional Port C.S. Trim 1S00 lb. WOG T-590-CS Series NPT x NPT Federal Specifications: WW-V-35, Type II, Class D. Style 1 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Rated Steel 2. Handle Zinc Plated Steel, Plasllsol Coated 3. Packing Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5. Pack Gland Carbon Steel ASTM A-108 Type 12114, Phosphate Coated 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Carbon Steel ASTM A-108 Type 12114. Nickel Plated 9, Body Carbon Steel ASTM A-108 Type 12L14, Phosphate Coated 10. Body Bolts Carbon Steel ASTM A-449GR 5, Zinc Plated 11. Body Nuts Zinc Plated Steel 12. Body Ends Carbon Steel ASTM A-105 13. Ball Carbon Steel ASTM A-108 Type 12L14, Nickel Plated 14. Seat Ring (2) Reinforced TFE 15. 0-Ring Seal (2) TFE DIMENSIONS - WEIGHTS Size A 8 C E F G Net Wt. Vt 2% 2 % Vm 5'A 2%> 1.6 % 2,S/l6 2V. % 6% 25/is 2.5 1 3% m *%2 ',6 6% 2ie 4.3 VA 4>/2 3 1'/.* 1 8!4 3% 7.4 VA 5s/ 3'/j iy,6 VA 8Vi 4'%2 11.2 2 S'%2 4 VA 8*/2 AVn 15.0 NOTE: For specific pressure/temperature relationships refer to page 67. T-590-CS-R-25 threaded Reinforced TFE Seats and Seals with C.S. trim K-590-CS-R-25 socket-weld ends Reinforced TFE Seats and Seals with C.S. trim NIBCO INC.. ELKHART. INDIANA 25 NIBCO000811 MIBCO carbon steel ball valves Three-Piece Body Blowout-Proof Stem Conventional Port 316 S.S. Trim 1500 lb. WOG $ Federal Specifications: WW-V-35, Type II, Class D, Style 1 T-590-CS Series NPT x NPT K-590-CS Series SOC x SOC MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel z Handle Zinc Plated Steel. Plastlsol Coated 3. Packing Nut Zinc Plated Steel N 4' Belleville Washer 5. Pack Gland Zinc Plated Steel Carbon Steel ASTM A-108 Type 12L14, Phosphate Coated 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Stainless Steel ASTM A-276 Type 316 9. Body Carbon Steel ASTM A-t08 Type 12114. Phosphate Coated id. Body Bolts Carbon Steel ASTM A-449 GR 5. Zinc Plated 11. Body Nuts 3nc Plated Steel 12. Body Ends Carbon Steel ASTM A-I05 13. Balt Stainless Steel ASTM A-276 Type 316 14. Seal Ring !2) Reinforced TFE 15. O-Ring Seal {2) TFE DIMENSIONS - WEIGHTS Size A B C E F G Net Wt. 'h zv, 2 2,Az V,s 5'/4 2%z 1.6 % 2'% 2'/4 Vn 6% 2s/i 2.5 1 3% 2% '.6 6% 2/,s 4.3 1 Vi 414 3 va6 1 8% 3% 7.4 PA 5% 3!4 Ws PA 8>/z 4'%z 11.2 2 5'%z 4 1% PA 8'/z 4,t 15.0 T-590-CS-R-66 threaded Reinforced TFE Seats and Seals with S.S. trim K-590-CS-R-66 socket-weld ends Reinforced TFE Seats and Seals with S.S. trim NOTE: For specific pressure/temperature relationships refer lo parje67 26 NIBCO INC.. ELKHART, INDIANA NIBCO000812 IMIBCO t stainless steel ball valves Three Piece Body Blowout-Proof Stem Conventional Port 316 S.S. Trim 1500 ib. WOG T-590-S6 Series NPT x NPT K-S90-S6 Series SOC x SOC Federal Specifications: WW-V-35, Type II, Class C, Style 1 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Stainless Steel. ASTM A194 GR 8 (304) 2, Handle Stainless Steel. ASTM A-167 Type 304. Plastisaf Coated 3. Packing Nut Stainless Steel. ASTM A194 GR 8 (304) 4. Belleville Washer Ds. Pack Gland Stainless Steel. ASTM A-167 Type 304 Stainless Steel. ASTM A-276 Type 316 8. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Stainless Steel, ASTM A-276 Type 316 9. Body Stainless Steel. ASTM A-276 Type 316 <%"%') Stainless Steel. ASTM A351 GR CF8M (T-2") 10. Body Bolts Stainless Steel. ASTM B193 GR B 8 Type 304 11. Body Nuts Stainless Steel. ASTM 8194 GR 8.(304) 12. Body Ends Stainless Steel. ASTM A-351 Grade CF3M 13. Ball Stainless Steel. ASTM A-276 Type 316 14. Seat Ring (2) Reinforced TFE 15. 0-Ring Seal (2) TFE DIMENSIONS - WEIGHTS Slie A B 'h 2% 2 CE F % Vn S>/4 G 2%a Net Wt. 1.6 % 2'Vn 2V* % S/,6 6% 2s/,e 2.5 1 >>3323/3A2* 2'h ,3/,6 6% 2l 4.3 W 4% 3 1VW 1 8V4 3% 7.4 m 5s/,8 3'/? iy. 1!4 SVi 4'%i 11.2 2 5'%a 4 i% 8V4 4V,s 15.0 NOTE: For specific pressure/temperature relationships refer to page 67. T-590-S6-R-66 threaded Reinforced TFE Seats and Seals with S.S. trim K-590-S6-R-66 socket-weld ends Reinforced TFE Seats and Seals with S.S. trim NIBCO INC., ELKHART, INDIANA 27 NIBCO000813 IMIBCO carbon steel ball valves Three Piece Body Blowout-Proof Stem C.S. Trim Conventional Port Class 150 Federal Specifications: WW-V-35, Type II, Class D, Style 1 F-590-CS Series MATERIAL LIST PART SPEnFIOTON 1. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel. Plaslisol Coaled 3. Packing Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5, Pack Gland Carbon Steel ASTM A-108 Type 12L14, Phosphate Coated 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Carbon Sfeel ASTM A-108 Type 12114. Nickel Plated 9. Body Carbon Steel ASTM A-108 Type 12114, Phosphate Coated 10. Body Bolts Carbon Steel ASTM A449 GR 5. Zinc Plated 11. Body Nuts Zinc Plated Steel 12. Body Ends Carbon Steel ASTM A-105 13. Ball Carbon Steel ASTM A-108 Type 12L14, Nickel Plated 14. Seat Ring (2) Reinforced TFE 15. 0-Ring Seal (2) TFE DIMENSIONS -- WEIGHTS Ket Size A 8 c 0 1 F G M Wt 'k 4*4 m 3'k 23/i 'As 43/ 3 2'h 3.5 H, 4% I'V# 3'h 2?k ?f( 5'/. 3'A m 5.5 1 5 2 4'U 2% %s 5% 33A 27i 7.3 1% 5% 2'h m 2'h t 8h 37. 27. 11.0 t <h 6% 2% 5 3'k 1'/. &'h 4 3'A 15.0 2 7 m 6 4 1% m 4 2'h 20.0 NOTE: For specific pressure/temperature relationships refer to page 67. F-59Q-CS-R-25 flanged ends Reinforced TFE Seats and Seals with C.S. trim 28 NIBCO INC., ELKHART, INDIANA NIBCO000814 MIBCO carbon steel ball valves Three Piece Body Blowout-Proof Stem 316 S.S. Trim Conventional Port Class 150 F-590-CS Series Federal Specifications; WW-V-35, Type II, Class D, Style 1 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel. Plastisol Coated 3. Packing Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5. Pack Bland Carbon Steel ASTM A-108 Type 12114, Phosphite Coaled 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Stainless Steel ASTM A-276 Type 316 9. Body Carbon Steel ASTM A-108 Type 12L14, Phosphate Coaled 10. Body Bolts Carbon Steel ASTM A-449 GR 5, Zinc Plated 11. Body Nuts Zinc Plated Steel 12. Body Ends Carbon Steel ASTM A-105 13. Ball Stainless Steel ASTM A-276 Type 316 14. Seal Ring (2) Reinforced TFE IS. 0-Ring Seal (2) TFE DIMENSIONS -- WEIGHTS Nit Slle A B c B E F & M m 'k 4'/. Ph m 2% 7* 4V< 3 2% 3.5 7, 4s/. V'h m 2V % 5% 3V. 27* 5.5 1 5 2 4*/< 3'/ %, 5'/. 3% 2'h 7.3 17. 5'h 2'h m 3'/. 1 8% 3% 27. 11.0 1 'h Mi 2'k 5 3% 1% 8% 4 3'/. 15.0 2 7 m 6 4V. 1'/. 8Vi 4 3% 20.0 NOTE: For specific pressure/temperature relationships refer to page 67. F-590-CS-R-66 flanged ends Reinforced TFE Seats and Seals with S.S. trim NIBCO INC.. ELKHART, INDIANA 29 NIBCO000815 stainless steel ball valves Three Piece Body Blowout-Proof Stem 316 S.S. Trim Conventional Port Class 150 $ F-59Q-S6 Series Federal Specifications: WW-V-35, Type II, Class C, Style 1 MATERIAL LIST PART SPECIFICATION 1. Handle Nut Stainless Steel ASTM A194 GR 8 {304) 2. Handle Stainless Steel ASTM A-167 Type 304, Plaslisol Coated 3. Packing Nut Stainless Steel ASTM A194 GR 8 (304) 4. Belleville Washer Stainless Steel ASTM A-167 Type 304 5. Pack Gland Stainless Steel ASTM A-276 Type 316 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Stainless Steel ASTM A-276 Type 316 9. Body Stainless Steel ASTM A-276 Type 316 (W-W) Stainless Steel ASTM A351 GR CF8M (1*-2") 10. Body Bolts Stainless Steel ASTM 8193 GRB 8 Type 304 11. Body Nuts Stainless Steel ASTM B-194 GR 8.(304) 12. Body Ends Stainless Steel ASTM A-351 Grade CF8M 13. Ball Stainless Steel ASTM A-276 Type 316 14. Seat Ring 0 Reinforced TFE 15. 0-Ring Seal (2) TFE F-590-S6-R-66 flanged ends Reinforced TFE Seats and Seals with S.S. trim DIMENSIONS -- WEIGHTS Net Size A B c D E F S M Wl Vi 4V< 11i 3% 2'A 7# 4V. 3 2Vi 3.5 V, 4% 1'V,e 3% 27. V,, 57. 3*A 27* 5.5 1 5 2 4V. 37. /* 5% 3. 2% 7.3 17. 5'A 2Vi 4% 3% 1 2,'h 3% 27. 11.0 i'/} m 27. 5 3% IV. Vk 4 3'A 15.0 2 7 m 6 4% I'A 10s/. 4 3'A 20.0 NOTE: For specific pressure/temperature relationships refer to page 67. 30 NIBCO INC., ELKHART, INDIANA NIBCO000816 IMIBCO bronze ball valves Three Piece Body * Blowout-Proof Stem Full Port Bronze Trim 150 PSI Saturated Steam 600 PSI Non-Shock Cold Water, Oil, or Gas Federal Specifications: WW-V-35, Type II, Class A, Style 1 T-59S-Y NPT x NPT MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel z Handle Zinc Plated Steel. Plastisol Coated 3. Racking Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5. Travel Slop Zinc Plated Steet 8. Stem Silicon Bronze ASTM B-371 Alloy 694 7, Pack Gland Brass ASTM B-16 8. Body Bronze ASTM B-584 Alloy 844 a Packing Reinforced TFE 10. Body Ends Cast Bronze ASTM B-584 Alloy 844 51. 0-Ring Seal (2) Fluorocarbon Rubber 12. Seat Ring (21 TFE 13. Ball" Cast Bronze ASTM B-584 Alloy 844 14. Ground Device Stainless Steel. 316 SS 15. Thrust Washer Reinforced TFE 16. Body Bolts Zinc Plated Sieel 17. Body Nuts Zinc Rated Steel Ball Material on Vi", V and V is Brass, ASTM 8-16. S-595-Y Copper x Copper DIMENSIONS -- WEIGHTS -- QUANTITIES Nom. Dim. A Dim. A Size Threaded Solder Dimensions B.C. B. and E same lor solder and threaded ends 8CD E Approx. Approx. Dim. F Weight Weight Cln. Solder Threaded Solder Oly. 1W i"/ 1/ 'h 2V 3/ 1V 0.6 0.6 50 J/s 2'k 1 1 %t h Vto 3/m 17,8 0.7 0.7 50 h 2h 2% 1/,. h 2'hi 3/ 17,8 0.8 0.8 50 V. 3'/., 2'Vtt IRA. V. 2/ 4!Vj! 17,8 1.4 1.2 30 1 3"/ V'h 2% 1 2'h 4"/m 1"/k 3.0 2,9 10 I1/. 4 3'Vn 2"la 1% 3V 6y 1s*& 4.0 3.9 10 I'* 4V VHu 3 Vh 3"/m 6"/ 2%i 6.0 5.6 6 2 6Vn 5fe 4 2 3"M 6"f 7?hi 10.1 9.9 5 2'A 6& 6"/t* 5 2'k 4"/,6 8 4 17.0 15.0 4 NOTE: For specific pressure/temperature relationships refer to page 67. NIBCO INC., ELKHART, INDIANA T-595-Y threaded TFE Seats with Bronze trim S-595-Y solder TFE Seats with Bronze trim 31 NIBCO000817 IMIBCO bronze ball valves Three Piece Body Blowout-Proof Stem Full Port 316 S.S, Trim 150 PSI Saturated Steam 600 PSI Non-Shock Cold Water, Oil, or Gas T-S9S-Y NPT x NPT Federal Specifications: WW-V-35, Type II, Class A, Style 1 MATERIAL LIST PART 1. Handle Nut SPECIFICATION Zinc Plated Steel 2. Handle Zinc Plated Steel, Ptastisol Coaled 3. Packing Nut Zinc Plated Steel 4. Belleville Washer 8. Travel Stop Zinc Plated Steel Zinc Plated Steel 8. Stem Stainless Steel ASTM A-276 Type 316 7. Pack Gland Brass ASTM B-16 & Body Bronze ASTM 8-584 Alloy 844 9. Packing Reinforced TFE 10. Body Ends Cast Bronze ASTM B-584 Alloy 844 11. 0-Ring Seal (2) Fluorocarbon Rubber It Seat Ring (2) TFE 13. Ball Cast Bronze ASTM A-276 Type 316 14. Ground Device Stainless Steel. 316 SS 15. Thrust Washer Reinforced TFE 16. Body Bolts Zinc Hated Steel (not shown) 17. Body Nuts Zinc Plated Steel (not shown) T-595-Y-66 threaded TFE Seats with S.S. trim S-595-Y Copper x Copper DIMENSIONS -- WEIGHTS -- QUANTITIES Horn. Dim. A Dim. A Size Threaded Solder Qlmtnslons 8, C. 0. and E same for solder and threaded ends BCBE Dim. F Solder Approx. Approx. Weight Weight Threaded Solder cm. Oiy. V, 2'h 1 ahi TV,. V; 2'h 3/ 1 >/ 0.6 0.6 50 % 2V; 1 ahi I'Vis V; 2'In 3"/a m 0.7 0.7 50 V; 2'h 1!Y 1'V 'h 2 3i!/ m 0.8 0.8 50 V, 3V* 2al* 1/u V. 2*Z 4Jl/j; Vh 1.4 1.2 30 1 3'V* P'hi 2'h 1 2'h 4'Vk 1 "In 3.0 2.9 10 IV. 4 3"/ 2"1* IV. 3V 6'V* V'ln 4.0 3.9 10 1% VI* 2%? 3 IV; 3'Vh 6"/u 2"In 6.0 5.6 6 2 6%; 4 2 3'Vi. 6/a 3%; 10.1 9.9 5 2 '/> 6"/ 6/ 5 2V; 4"l* 8 4 17.0 15.0 4 S-595-Y-66 solder TFE Seats with S.S. trim NOTE: For specific pressure/temperature relationships refer to page 67. 32 NIBCO INC., ELKHART, INDIANA NIBCO000818 IMIBCO carbon steel ball valves Three Piece Body Blowout-Proof Stem * C.S, Trim Full Port 1500 lb. WOG Federal Specifications: WW-V-35, Type II, Class D, Style 1 T-595-CS Series NPT x NPT K-595-CS Series SOC x SOC MATERIAL LIST PART SPECIFICATION _ 1. Handle Nut 0 2. Handle Zinc Plated Steel Zinc Plated Steel. Plastisol Coated 3. Packinj Nut Zinc Plated Steel 4. Belleville Washer Zinc Plated Steel 5. Pack Gland Carbon Steel ASTM A-108 Type 12114. Phosphate Coated 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Carbon Steel ASTM A-10B Type 12114, Nickel Plated 9. Body Carbon Steel ASTM A-108 Type 12L14, Phosphate Coaled 10. Body Bolts Carbon Steel ASTM A449 GR 5, Zinc Plated 11. Body Nuts Zinc Plated Steel 12. Body Ends Carbon Steel ASTM A-10S 13. Sail Carbon Sleet ASTM A-108 Type 12114. Nickel Plated 14. Seat Ring |2) Reinforced TFE 15. 0-Ring Seal (2) TFE DIMENSIONS - WEIGHTS Size A B C E f G Net Wl. 'A 2% 2 % Vn 5'A 2% 1.6 % 2% 2 2l/32 ?/is 5'A 2%2 1.6 '/! 2'y 2V, 2%2 s/is 6% 2s/,E 2.5 % 3% 2Vz 2%2 ,3/l6 6% 2Vm 4.3 1 414 3 VAs 1 m 3% 7.4 VA 55/i6 314 iy. VA 314 A'Va 11.2 I'/e 5'%! 4 m 8V4 4'/, 6 15.0 2 5'%a 4<M6 1'%a 2 m 4% 15.5 NOTE: For specific pressure/temperature relationships refer to page 67. NIBCO INC., ELKHART, INDIANA T-595-CS-R-25 threaded ends Reinforced TFE Seats and Seals with C.S. trim K-595-CS-R-25 socket-weld ends Reinforced TFE Seats and Seals with C.S. trim 33 NIBCO000819 IMIBCO carbon steel ball valves Three Piece Body * Blowout-Proof Stem 316 S.S. Trim Full Port 15001b. WOG Federal Specifications: WW-V-35, Type II, Class D, Style 1 T-595-CS Series NPT x NPT MATERIAL LIST PART SPECIFICATION 1. Handle Nut Zinc Plated Steel Handle Zinc Plated Steel, Plastisol Coated <5 3- pMkinBNut 7 4, Belleville Washer 5, Pack Gland Zinc Plated Steel Zinc Plated Steel Carbon Steel ASTM A-108 Type 12114, Phosphate Coated 6. Packing Reinforced TFE 7. Thrust Washer Reinforced TFE 8. Stem Stainless Steel ASTM A-276 Type 316 9. Body Carbon Steel ASTM A-108 Type 12114, Phosphate Coated 10. Body Bolts Carbon Steel ASTM A-449 GR 5, 2inc Hated 11, Body Nuts Zinc Plated Steel 12, Body Ends Carbon Steel ASTM A-105 13. Ball Carbon Steel ASTM A-276 Type 316 14. Seat Ring (2) Reinforced TFE 15. 0-Ring Seal (2) TFE K-595-CS Series SOC x SOC DIMENSIONS1 - WEIGHTS Size A 8 C E F 5 Net Wt. '/ 2 7Ai 5% 2%a 1.6 % 2% 2 2'/j2 5'/ 2%a 1.6 V4 2'Vts 2'A % *As 6% 2s/,6 2.5 % 3% 1'h Wn 13/l6 6% 2s/,6 4.3 1 4V4 3 1Y,e 1 814 3% 7.4 PA 5y 3'A 1% PA 8'A 45%2 11.2 PA 5>% 4 1% PA 814 4s/,6 15.0 2 5% 4,s/is l'%2 2 m 4% 15.5 T-595-CS-R-66 threaded ends Reinforced TFE Seats and Seals with S.S. trim K-595-CS-R-66 socket-weld ends Reinforced TFE Seats and Seals with S.S. trim 34 NiBCO INC., ELKHART, INDIANA NIBCO000820 I stainless steel ball valves Three Piece Body Blowout-Proof Stem * 316 S.S. Trim Full Port 800 lb. WOG Federal Specifications: WW-V-35, Type II, Class C, Style 1 I T-595-S6 Series NPT xNPT MATERIAL LIST PAST SPECIFICATION 1.. Handle Nut Stainless Steel ASTM A492 Type 304 2. Ground Device Stainless Steel 316 SS 3. Handle Stainless Steel ASTM A-167 Type 304. Plastisol Coated 4. Packing Nut Stainless Steel ASTM A-194 GR 8 (304) 5. Belleville Washer Stainless Steel ASTM A-167 Type 304 6. Pack Gland Stainless Steel ASTM A-276 Type 316 7. Packing Reinforced TFE 8. Thrust Washer Reinforced TFE 9, Stem Stainless Steel ASTM A-276 Type 316 10. Body Stainless Steel. ASTM A-351 Grade CF8M ft. Body Bolts Stainless Steel ASTM A-493 Type 304 12. Body Nuts Stainless Steel ASTM A493 Type 304 13. Body Ends Stainless Steel. ASTM A-351 Grade CF8M 14. Ball Stainless Steel ASTM A-276 Type 316 15. Seat Ring (2) Reinforced TFE 16. 0-Ring Seal (2) Reinforced TFE T-595-S6-R-66 threaded ends Reinforced TFE Seats and Seals with S.S. trim K-595-SS Si in.-, SOC x SOC DIMENSIONS - WEIGHTS Size A 8 c E F G Net Wt. V, Vh 1% Vi* 7/l6 3% Vh .94 m i% '/is '/! 3% 1% .88 vs* a-vis Vli S/ 4'Ms 2Va 1.44 Yi 3"/5z Vh . 'y!6 Ww 2V2 2.00 \ 3*3/i6 VVn >y>6 i 5% Vh 2.88 is 4% 2% I'/us i1/. 5% 2% 4.88 1 V/ 5'/, 3%! V/n Vh 8V4 3% 7.38 2 6V4 4>y,fi 2%! 2 8'/. 3% 13.10 K-595-S6-R-66 sockef-weld ends Reinforced TFE Seats and Seals with S.S. trim NOTE For specific pressure/temperature relationships refer to page 67. NIBCO INC., ELKHART, INDIANA 35 NIBCO000821 butterfly valves illustrated index I Numerical Index Fig. No. Page WWWWWWWWLLLWWWWLLWLLLLLLLLDDDDDDDDDDDDDDDDDDDDDDDDDD------------0-33-202--3322-3---3-0-----32023001033310010132323**000110100111***040*21101101101101112341300004211111001102343100011............................................................................................................................................................................................................................................................... ,, ,, ,. ,. ., . ,. .. 4444444544455344444443344318110677892655240023349988 WD 2000 Sizes 2"-12" Moide<d-in liner Aluminum Bronze Disc Ductile Iron Body 260 PSi Lug Style Butterfly Valve LD 2600 sties r-ir Moided-in Uner Aluminum Bronze Disc WO 3111 Sizes 2'M2*' MoWed-in Uner Ductile iron Disc DuclHe Iran Body 250 PSi Lug Style Butterfly Valve LD 3iit Sizes r-12" Mofded-in Uner Ductile Iron Disc WD 0011 Sizes 14 24 Moldetf'in Angle*0i' i>* Ouciilr- inm Minty 150 fW Lug Style v-u I LO ooi s Sizes 14 24 Moided-in l i* Angle-Dr?c 0*hm* 1 Body Type W - Wafer l -- Lug 2 Body Material D -- Ductile Iron Key to NIBCO Butterfly Valve Figure Number Positions* 34 5 6 Pressure Rating Uner Material Disc Material Stem & Bushing Combination Stem Upper & Lower Collar 0-150 PSI 1 - 175 PSI 2 - 200 PSI 3 - 250 PSI 0 -- EPDM 1 -- Nitrile (8UNA-NJ 2 -- Fluoro- carton {VITON'J 3 -- Hypalon* 4 -- Neoprene 0 --Alum. Bronze2 t -- Ductile Iron3 2 - CF8M 3 -- CN7M 4 -- Monel 0-416 S.S. 1 - 416 S.S. 2 - 17-4PH S.S/ 3 -- Alloy 20 S.S. 4 -- Monel Brass 316 S.S. 316 S.S. Alloy 20 S.S. Monel Brass Brass 316 as. Alloy 20 S.S. Monel This key is a guide only and is nol intended to infer that any valve that is contained in the key will be made, 1, Trademark of E. I. DuPont Co. 2. Valve rated at 200 PSI when supplied with an aluminum bronze disc. 3. Electro nickel plated 4. Trademark of ARMCO Steel Co. NOTE: 14--24" carry a ISO PSI rating only. l Dpiif.illiiu Mnch.mli rn fl Him.- 1 U.'. 3 In-r l. 5 Ojlf-Mim 7 - ii.-thf- A< hi.ii*H 9 - I'flfiiin.iltt Ariti.ildi 36 NIBCO INC., ELKHART, INDIANA I NIBCO000822 HPR 2000 butterfly valves Field removable* threaded collar bushing. Body and stem O-ring seals of EPDM or Viton. Extended neck for insulation up to 2". Molded-in liner fully supported by valve body at flange seals. Eliminates leakage between body and liner as In cartridge or boot type liners. Best for dead-end service without the need for a flange on the downstream side. Liners are color-coded for easy material identification. High-strength stem materials with onepiece thru-disc stem design. Integrally cast operator/actuator mounting pad. Upper and lower bushings are standard for smooth valve operation. Streamlined spherical disc with high flow capacity. Internal stem/disc drive eliminates the need for pins or bolts which create addi tional leak paths and turbulence in the waterway that reduces flow. Ductile iron body reduces cracking due to abuse. Do not remove collar bushing with valve under pressure. A HIGH-PERFORMANCE RESILJENT-SEATED BUTTERFLY VALVE FEATURING: Pressure Rating to 250 PSI Wide choice of materials to suit customer's application Bubble-tight shutoff at full pressure rating Dead-end service at 200 PSI "Blind-hole" lower bushing prevents leakage. Sizes Available 2", 2W\ 3", 4", 5", 6". 8", 10", 12" Operation Bare shaft, lever-lock flow control handle, worm gear operator, electric and pneumatic actuators Body Styles Tapped full lug or wafer NIBCO INC.. ELKHART, INDIANA 37 NIBCO000823 JsEfcss 38 INilBCO 200 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner Lug and Wafer Type Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 Part 1. Siam 2. Collar Bushing 3. Siam Seal 4, Body Seal s. Nameplate 6. Upper Bushing ?. Uner 8. Disc 9, Lower Bushing 10. Body(\AWer) 11. Body(Lug! MATERIAL UST Specification Stainless Steel, ASTM A-582 Type 416 Brass, ASTM 8-16 EPDM Rubber EPDM Rubber Aluminum Brass, ASTM B-16 EPDM Rubber At. Bronze, ASTM B-148 Alloy 954 Brass, ASTM B-16 Ductile Iron, ASTM A-536 Ductile Iran, ASTM A-536 Size 2 214 3 4 5 6 3 10 12 A 2.15 2.65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C D EF G H Square 4.0 1.25 5.38 2.82 .38 .312 1.688 1.812 3.25 4.75 1,25 5.88 3.12 .38 .370 1.812 1.938 3.25 5.25 1.25 6.12 3.38 .38 .370 1.812 1.938 3.25 8.75 1.25 6.88 4.00 58 .403 2.062 2,188 3.25 7.82 1.25 7.38 4.75 .38 .496 2,188 2.312 3.25 8.62 1.25 8.00 5.25 .38 .496 2.188 2.312 3,25 10.87 1.25 9.25 6.50 .50 .560 2.375 2,500 3.25 13.25 1.25 10.50 8.00 .50 .686 2.688 2.812 4.75 16.0 1.25 12.00 9.25 .50 .748 3.000 3.125 4.75 LD 2000 lug style With EPDM Liner and Aluminum Bronze Disc Capscrew Data/Stud Data Lug Wafar Size N O PK B.C. Dia. No. L Wafer Lug M NefWL NefWL Ola. Length Length S.C. (Iba.) (lb.) 2 .500 3.25 .437 4 H-llunc 4 vu 414 7 6 214 562 3.25 .437 4 H-llunc 4% m 514 9 8 3 .562 3,25 .437 4 H-llunc 4Vt m 6 914 814 4 .625 3.25 .437 8 H-llunc 5 184 m 15 12 5 .750 3.25 .437 8 H-lQunc 5V* m 8% 19 IS 6 .750 3.25 .437 8 H-lQunc SV* 2 914 8 J75 325 .437 a H-IOunc 5% 2'A 11% 24 35 18 29 10 1.125 5.00 .562 12 H-9unc 6V* 214 1414 5614 4514 12 1.250 550 .562 12 H-9unc m 214 17 87 72 NIBCO INC., ELKHART, INDIANA WD 2000 wafer style With EPDM Liner and Aluminum Bronze Disc NIBCO000824 200 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner Lug and Wafer Type Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 Part 1. Stem 2. Collar Bushing a Stem Seal 4, Body Seat 5, Nameplate 6. Upper Bushing 7. Liner a Disc 9, Lower Bushing 10. Body Wafer 11. Body Lug MATERIAL LIST Specification Stainless Steel ASTM A-582 Type 416 Brass ASTM B-16 EPOM Rubber EPDM Rubber Aluminum Stainless Steel ASTM A-276 Type 316 EPDM Rubber AL Bronze ASTM B-148 Alloy 954 Stainless Steel ASTM A-276 Type 316 Ductile Iran ASTM A-536 Ductile Iron ASTM A-536 Size 2 2V4 3 4 5 6 8 10 12 A 2.15 2.65 3.15 4.15 545 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C 0 EF a H 1 Square 4.0 1.25 5,38 2.62 .38 .312 1.688 1.812 3.25 4.75 1.25 5.88 3.12 .38 .370 1512 1.938 3.25 5.25 1.25 6.12 3.38 .38 .370 1.812 1.938 3.25 6.75 1.25 6.88 4,00 .38 .403 2.062 2.188 3.25 762 1.25 7.38 4.75 .38 .496 2.188 2.312 3.25 8.62 1.25 8.00 5.25 ,38 .496 2.188 2.312 3.25 10.87 155 9.25 650 .50 .560 2,375 2.500 3.25 13.25 1.25 10.50 8.00 .50 .686 2.688 2.812 4.75 16.0 1.25 12.00 9.25 .50 .748 3.000 3.125 4.75 LD 2001 lug style With EPDM Liner and Aluminum Bronze Disc Size N 2 .500 2'h .562 3 .562 4 .625 5 .750 6 .750 8 .875 10 1.125 12 1550 O B.C. 3.25 3.25 3.25 3.25 355 355 3.25 5.00 S.00 Capscrew Data/Stud Data Lug Wafer Approx. PK Dla. No. L Wafer Lug M Net Wt Net Wt. Dia. Length Length B,C. (tbs.) (lbs.) .437 4 H-llunc 4 1V4 4V* 7 6 .437 4 Vi-llunc 4% m 5% 9 8 .437 4 H-llunc 4% m 6 954 8% .437 8 W-llunc 5 m 7% 15 12 437 8 %-iOunc 5V5 i* m 19 15 .437 a %-lQunc 5y. 2 m 24 18 .437 8 14-lOunc 5% 2V* 11% 35 29 .582 12 &-9unc 6'/. 2*/. 14V* 56% Am .562 12 %-9tmc 6% 2% 17 87 72 WD 2001 wafer style With EPDM Liner and Aluminum Bronze Disc NIBCO INC.,.ELKHART, INDIANA 39 NIBCO000825 200 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner * Lug and Water Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 Pad 1. Stem 2. Collar Bushing 3. Stem Seal 4, Body Seal 5. Nameplate 6. Upper Bushing 7. Liner 8. Disc 9. Lower Bushing to, Body Water 11. Body Lug MATERIAL LIST Specification Stainless Steel ASTM A-582 Type 416 Brass ASTM B-16 Fluorocarbon Rubber Fluorocarbon Rubber Aluminum Brass ASTM B-16 Nitrile BUNA-N Rubber Al Bronze ASTM B-148 Alloy 954 Brass ASTM B-16 Ductile Iron ASTM A-536 Ductile Iron ASTM A-536 Size A 2 2.15 214 2.65 3 3.15 4 4.15 5 5.15 6 6.15 8 8.15 10 10.15 12 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C D E F G H 1 Square 4.0 1.25 5.38 2.62 .38 .312 1.688 1.812 3.25 4.75 1.25 5.88 3.12 M .370 1.812 1.938 3.25 5.25 1.25 6.12 3.38 .38 .370 1.812 1.938 3.25 6.TS 1.25 6.88 4.00 .38 .403 2.062 2.188 3.25 7,62 1.25 7,38 4.75 .38 .498 2.188 2.312 3.25 8.62 1.25 8.00 5.25 .38 .496 2.188 2.312 3.25 10.87 1.25 9.25 6.50 .50 .560 2.375 2.500 3.25 13,25 1J25 10.50 8.00 .50 .686 2.688 2.812 4.75 16.0 1.25 12.00 9.25 .50 .748 3.000 3.125 4.75 LD 2100 lug stylo With Nitriln Liner and Aluminum Bronze Disc Size N Capscrew Data/Stud Data Lug Water Approx. Apprcx. O PK L Water Lug M Net Wt. Net WL B.C. DIa. No. Ola. 1Length Length B.C. (Ibs.i (lbs.) 2 .500 3J2S .437 4 14-11 unc 4 VA 444 7 6 2% .562 3.25 .437 4 44-1 lunc 4*4 144 544 9 8 3 .562 3.25 .437 4 44-11 unc 4'/< m 6 954 854 4 .625 3.25 .437 a 44-11 unc 5 144 744 15 12 5 .750 3.25 .437 $ 44-IQunc 5'A 144 8% 19 15 6 .750 3.25 .437 8 %-t0unc 514 8 .875 3.25 .437 a 44-1 Ounc 5V 2 944 214 1144 24 35 18 29 10 1.125 5.00 .562 12 54-9unc 644 214 14'A 5654 4554 12 1.250 5.00 .562 12 '/4-9unc 644 2*4 17 87 72 WD 2100 water style With Nitrile Liner and Aluminum Bronze Disc 40 NIBCO INC., ELKHART, INDIANA NIBCO000826 IMIBCO 200 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner Lug and Wafer Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 IrZl' 0*' Part 1. Stem 2. Collar Bushing 3. Stem Seal 4. Body Seal s. Nameplate 6. Upper Bushing 7. Liner 8. Disc 9. Lower Bushing 10. Body Wafer n. Body Lug MATERIAL LIST SpecHication Stainless Steel ASTM A-582 Type 416 Brass ASTM B-1B Fluorocarbon Rubber Fluorocarbon Rubber Aluminum Stainless Steel ASTM A-278 Type 316 Nitrile BUNA-N Rubber Al. Bronze ASTM B-148 Alloy 954 Stainless Steel ASTM A-276 Type 316 Ouctlle Iron ASTM A-536 Ductile Iron ASTM A-536 Size 2 2% 3 4 s 6 8 10 12 A 2.15 2.65 3.1 S 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C 0 iF G H Square 4.0 1.25 5.38 2.62 .38 .312 1.688 1.812 3.25 4,75 1.25 5.88 3.12 38 .370 1,812 1.938 3,25 525 1.25 6.12 3.38 38 .370 1512 1.938 3.25 6.75 1.25 6.88 4.00 .38 .403 2.062 2.188 3.25 7.62 1.25 7.38 4.75 .38 .496 2.188 2.312 325 8.62 1.25 8.00 525 .38 .496 2.188 2.312 325 10.87 1.25 925 6.50 .50 560 2.375 2.500 3.25 1325 1.25 10.50 8,00 .50 .686 2.688 2.812 4.75 16.0 125 12.00 925 .50 .748 3.000 3.125 4.75 LD 2101 lug style With Nitrile Liner and Aluminum Bronze Disc Size N Capscrew Data/Stud Data Lug Wafer Approx. Approx. O PK L Water Lug M Net Wt. Net WL B.C. Dia. No. Dta. 1Length Length B.C. Elbs.) (lbs.) 2 .500 3.25 .437 4 14-11 unc 4 1'/4 4% 7 6 254 .562 325 .437 4 14-1 lunc 4'/. 154 5% 9 6 3 .562 325 .437 4 14-11 unc 4Va m 6 954 854 4 .625 325 .437 8 14-1 lunc 5 m m 15 12 5 ,750 3.25 .437 8 %~1Qurvc 5'A m 814 19 15 WD 2101 wafer style 6 .750 325 .437 8 W-iOune- 5>A 2 m 24 18 With Nitrile 8 .875 3.25 .437 8 H-IQunc m 2V< 1114 35 29 Liner and I 10 1.125 5.00 .562 12 54-9unc m 2V, 14'A 5654 4554 12 1250 5.00 .562 12 y-9unc 614 254 17 87 72 Aluminum Bronze Disc NIBCO INC., ELKHART. INDIANA 41 NIBCO000827 IMIBCO 250 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner Lug and Wafer Type Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 Part 1. Stem 2. Collar Bushing 3. Stem Seal 4, Body Seal 5. Nameplate & Upper Bushing 7. liner 8. Disc 9. lower Bushing 10. Body (Wafer) 11. Body(Lug) MATERIAL LIST Specification Stainless Steel, ASTM A-582 Type 416 Brass, ASTM B-1S EPDM Rubber EPDM Rubber Aluminum Brass, ASTM B-16 EPDM Rubber Ductile Iron. ASTM A-395 (Plated) Brass. ASTM 8-16 Ductile Iron. ASTM A-S36 Ductile Iron, ASTM A-536 Size 2 ZV> 3 4 5 6 8 10 12 A 2.15 2,65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 B 4.0 4.75 5.25 8.75 7.62 8.62 10.87 13.25 16.0 DIMENSIONS -- WEIGHTS Melal CD EF G H 1.25 5.38 2.62 .38 .312 1.688 1.25 5.88 3.12 .38 .370 1.812 1.25 6.12 3.38 .38 .370 1.812 1.25 6.88 4.00 .38 .403 2.062 1.25 7.38 4.75 ,38 .496 2.188 1.25 8.00 5.25 .38 .496 2.188 1.25 9.25 6.50 .50 .560 2.375 1.25 10.50 8.00 .50 .686 2.688 1.25 12.00 9.25 .50 .748 3.000 Rubber J Square 1.812 3.25 1.938 3.25 1.938 3.25 2.188 3.25 2.312 3.25 2.312 3.25 2.500 3.25 2.812 4.75 3.125 4.75 LD 3010 lug style With EPDM Liner and Ductile Disc Size N 2 .500 2n .562 3 .562 4 .625 5 .750 6 .750 8 .875 10 1.125 12 1.250 O 8.C. 3.25 3.25 3.25 325 3.25 3.25 3.25 5.00 5.00 Capscrew Oata/Stud Data Lug Wafer Approx. Approx. PK L Wafer lug M Net Wt. Net Wt. Oia. No. Dia. length Length B.C. (lbs.) (lbs.) .437 4 H-llunc 4 VA m 7 6 .437 4 tt-llunc 4% Vh 5% 9 8 .437 4 %-11unc m t% 6 9A 8% ,437 8 14-1 lunc s 1% Vh 15 12 .437 8 V.-IOunc 5% m 8'A 19 15 .437 8 %-lOunc 5% 2 9'A 24 18 .437 8 %-10unc 53A 2V4 11% 35 29 .562 12 J/-9urc 6V4 2'A 14% 561* 451* .562 12 ?/-9unc 614 2V5 17 87 72 WD 3010 wafer style With EPDM Liner and Ductile Disc 42 NIBCO INC., ELKHART. INDIANA NIBCO000828 W^ ^ IMIBCO 250 psi butterfly valves Ductile Iron Body * Extended Neck Geometric Drive Molded-fn Seat Liner Lug and Wafer Type Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 Part 1. Stem 2. Collar Bushing 3. Stem Seal 4, Body Seal 5. Nameplate 6. Upper Bushing 7. Uner 8. Disc 9, Lower Bushing to, Body (Water) 11. Body (Lug) MATERIAL LIST Specification Stainless Steel, ASTM A-582 Type 416 Brass, ASTM 8-16 EPDM Rubber EPDM Rubber Aluminum Stainless steel. ASTM A-276 Type 316 EPDM Rubber Ductile Iron. ASTM A-395 (Plated! Stainless Steel. ASTM A- 276 Type 316 Ductile Iron. ASTM A-535 Ductile Iron. ASTM A-536 Size 2 244 3 4 5 6 8 10 12 A 2.15 2.65 3.15 4.15 5.15 6.15 8,15 10.15 12.15 B 4,0 4.75 5.25 6,75 7.62 8.62 10.87 13.25 16.0 DIMENSIONS -- WEIGHTS Metal C0 EF 6 H 1.25 5.38 2.62 .38 .312 1.688 1.25 5.88 3.12 .38 .370 1.812 1.25 6.12 3.38 .38 .370 1.812 1.25 6,88 4.00 .38 .403 2.062 1.25 7.38 4.75 .38 .496 2.188 1.25 8,00 5.25 .38 .496 2.188 1.25 9.25 6.50 .50 .560 2.375 1.25 10.50 8.00 .50 .686 2.688 1.25 12.00 9.25 so .748 3.000 Rubber J Square 1.612 3.25 1.938 3.25 1.938 3.25 2.188 3.25 2.312 3.25 2.312 3.25 2.500 3.25 2.812 4.75 3.125 4.75 LD 3011 lug style With EPDM Liner and Ductile Disc Capscrew Data/Stud Data Lug Wafer Size N O PK B.C. Dia. No. l Water Lug M Net WL Net WL Dla, Length Length B.C, (lbs.) (lbs.) 2 .500 3.25 .437 4 %-llunc 4 VA 414 7 6 244 .562 3.25 .437 4 H-llunc 4V* m 544 9 8 3 .562 3.25 .437 4 H-llunc m . 6 m 8% 4 .825 325 .437 8 %-11unc 5 114 714 15 12 5 .750 3.25 .437 8 14-10unc 5'/* m an 19 15 6 .750 3.25 .437 8 44-10unc 5V< 2 944 24 18 8 .875 3.25 .437 8 14-10unc 514 2V4 11% 35 29 10 1.125 5.00 .562 12 '/-9unc 644 2'A 1414 5644 4544 12 1250 5.00 .562 12 '/-9unc 614 244 17 87 72 NIBCO INC., ELKHART, INDIANA WD 3011 wafer style With EPDM Liner and Ductile Disc 43 NIBCO000829 fpyiBcol 250 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner Lug and Wafer Sizes 2" through 12" . f Applicable Specifications: MSS-SP67, MSS-SP25, API-609 Part 1 Stem 2. Cotter Bushing 3. Stem Sea! 4. Body Seat 5. Nameplate 6. Upper Bushing 7. Liner 8. Oise 9. Lower Bushing 10. Body Water 11. Body Lug MATERIAL LIST Specification Stainless Steel ASTM A-582 Type 416 Brass ASTM B-16 Fluorocarbon Rubber Fluorocarbon Rubber Aluminum Brass ASTM 8-16 Nitrile (BUNA-N) Rubber Ductile Iron ASTM A-395 (Plated) Brass ASTM 8-16 Ductile Iron ASTM A-536 Ductile Iron ASTM A-536 Size 2 2% 3 4 5 6 8 10 12 A 2.15 2.65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C D EF G H Square 4.0 1.25 5.38 2.62 .38 .312 1.688 1.812 325 4.75 1.25 5.88 3.12 .38 .370 1.812 1.938 325 5.2S 1.25 6.12 3.38 .38 .370 1.812 1.938 3.25 6.75 1.25 6.88 4.00 .38 .403 2.062 2.188 3.25 7.82 1.25 7.38 4.75 .38 .496 2.188 2.312 3.25 8.62 1.25 8.00 5.25 ,38 .496 2.188 2.312 3.25 10.87 1.25 9.25 8.50 .50 .560 2.375 2.500 3,25 13.25 1.25 10.50 8.00 .50 .686 2.688 2.812 4.75 16.0 1.25 12X10 9.25 .50 ,748 3.000 3.125 4.75 Size N 2 .500 2% .582 3 .562 4 .825 5 .750 6 .750 8 .875 10 1.125 12 1.250 0 B.C. 3.2S 3.25 3.25 3,25 3.25 3.25 3.25 5.00 5.00 Capscrew Dala/Stud Data Lug Water PK Dia. No. L Water Lug M Net WL Net Wt. Dla. Length Length B.C. (lbs.) (lbs.) .437 4 %-tlunc 4 v/i 4% 7 6 .437 4 H-llunc 4V< 1% 5% 9 8 .437 4 H-llunc 4 Vi 1% 6 9% 8% .437 8 %-11unc s 114 7% 15 .437 8 14-1 Ounc 5% m 8% 19 12 15 .437 8 14-1 Dune 5V, 2 914 .437 a 14-1Ounc 514 214 11% 24 35 18 29 .562 12 F-9unc 6'/, 2V4 14% 56% 45% .562 12 %-9unc 6% 215 17 87 72 lug style With Nitrile Liner and Ductile Disc WD 3110 wafer style With Nitrile Liner and Ductile Disc 44 NIBCO INC., ELKHART, INDIANA NIBCO000830 NIBCO 250 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Molded-in Seat Liner Lug and Wafer Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 >1 F1 Part t Stem 2. Collar Bushing 3. Stem Seal 4. Body Seal 5. Nameplate 6. Upper Bushing 7, Liner S. Disc 9. Lower Bushing 10. Body Wafer 11. Body Lug MATERIAL LIST Specification Stainless Steel ASTM A-582 Type 416 Brass ASTM B-16 Fluorocarbon Rubber Fluorocarbon Rubber Aluminum Stainless Steel ASTM A-276Typ* 316 Nitrile (BUNA-N) Rubber Ductile Iran ASTM A-395 (Plated) Stainless Steel ASTM A-276 Type 316 Ductile Iron ASTM A-538 Ductile Iron ASTM A-536 Size Z'A 10 12 2.15 2.65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS B0 Metal Rubber J H Square 4.0 1.25 5.38 2.62 38 .312 1.688 1.812 3.25 4.75 1.25 5.88 3.12 38 .370 1.812 1338 3.25 5,25 1.25 6.12 3.38 38 .370 1.812 1.936 3.26 6.75 1.25 6.88 4.00 38 .403 2.062 2.188 3.25 782 1.25 7.38 4.75 38 .496 2.188 2.312 3.26 8.62 1.25 8.00 5.25 38 .496 2.186 2.312 3.25 10.87 1.25 9.25 650 50 .560 2.375 2.500 335 1325 1.25 1080 8.00 50 .686 2.688 2.812 4.75 16.0 1.25 12.00 9.25 50 .748 3.000 3.125 4.75 Capscrew Data/Stud Data O PK L Wafer Lug M siz<L N B.C. Dia. No. Dia. Length Length B.C. 2 .500 3.25 .437 4 H-llune 4 IV. m 254 .562 3.25 .437 4 H-llunc 4V. 1W S'h 3___ .562 3.25 .437 4 %-11unC 4V. U4 4 625 335 .437 8 tt-llunc 5 1% m 5 750 3.25____.4_3_7__ S V.-IOunc 5'/. 1. 8% 6 750 3.25 .437 8 V.-IOunc 5V< 9'A H B75 3.25____.4_3_7______8___W__-_IO__u_n_c 5W 2V. 11V. 10 t 125__ 5.00 .562 12 V(-9unc_____6__V_. _ _ 2V. 14V. 17 >250 5.00 .562 12 5i-9une 6=4 Vh 17 Lug Wafer Approx. Approx, Net Wt. Net Wt. (lbs.) fibs.) 954 814 15 12 19 15 24 18 35 29 56W 4554 87 72 NIBCO INC., ELKHART. INDIANA LD 3111 lug style With Nitrile Liner and Ductile Disc WD 3111 wafer style With Nitrile Liner and Ductile Disc 45 NIBCO000831 IMIBCO 250 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive 316 S.S. Trim Molded-in Seat Liner Lug and Wafer Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 -- J-----... --p8 _~'U ^-- OP ` i1 46 MATERIAL LIST Part Specification i. Stem Stainless Steel ASTM A-S64 Type 1T-4PH 2. Collar Bushing Stainless Steel ASTM A-276 Type 316 3. Stem Seal Fluorocarbon Rubber 4, Body Seal Fluorocarbon Rubber 5. Nameplate 8. Upper Bushing Aluminum Stainless Sleel ASTM A-276 Type 316 7, Liner 8. Disc Options: See Below* Stainless Steel ASTM A-743 Grade CF8M 9. Lower Bushing Stainless Steel ASTM A-276 Type 316 10. Body Wafer Ductile Iron ASTM A-536 11. Body Lug Ductile Iron ASTM A-536 Optional Liners: 0 -- EPOM 1 -- Nitrile (BUNA-N) 2 -- Fluorocarbon 3 - Hypalon 4 -- Neoprene Size 2 2 VS 3 4 5 6 8 10 12 A 2.15 2.65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C D EF G H Square 4.0 1.25 5,38 2.62 .38 .312 1.688 1.812 3.25 4.7S 1.25 5.88 3.12 .38 .370 1612 1.938 3.25 5.25 1.25 6.12 3.38 .38 070 1.812 1.938 3.25 6.75 1.25 6.88 4.00 .38 .403 2.062 2.188 3.25 7.62 1.25 7.38 4.75 .38 .496 2.188 2.312 3.25 8.62 1.25 8.00 5.25 .38 .496 2.188 Z312 3.25 1067 1,25 9.2S 6.50 .50 660 2.375 2.500 3.25 13.25 1.25 10.50 8.00 .50 ,686 2688 2.812 4.75 160 1.25 12.00 9.25 .50 .748 3.000 3.125 4.75 Size N Capscrew Data/Stud Data Lug Waler Approx. Approx. O PK L Water Lug M NetWI. NelWt. B.C. Dia. No. Ola. Length Length B.C. (lbs.) (to*.) 2 .500 3.25 .437 4 14-11 unc 4 1V4 m 7 6 214 .562 3.25 .437 4 14-1 lunc 4VS 1 Vi 5VS 9 8 3 .562 3.25 .437 4 14-11 unc 4*A m 6 914 854 4 625 3.25 .437 8 14-11 unc 5 i y< 714 15 12 5 .750 3.25 .437 8 U-lOunc 5% 814 19 15 6 .750 3.25 .437 8 %-lOunc 5V4 2 914 24 18 8 .875 3.25 .437 8 H-lOunc S3/< 254 II3/. 35 29 10 1.125 5.00 .562 12 54-9unc 6V 2V4 14'/* 5654 45V4 12 1.250 5.00 .562 12 54-9unc 61/. 2tt 17 87 72 NIBCO INC., ELKHART, INDIANA lug style With Optional Liner and CF8M Disc WD 3*22 wafer style With Optional Liner and CF8M Disc NIBCQ000832 NIBCO 250 psi butterfly valves Ductile Iron Body Extended Neck Geometric Drive Alloy 20 S.S. Trim Molded-in Seat Liner * Lug and Wafer Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 MATERIAL LIST Part Specification 1. Stem Stainless Steal ASTM B-473 Alloy 20 2. Collar Bushing Stainless Steel ASTM B-473 Alloy 20 3. Stem Seal Fluorocarbon Rubber 4. Body Seal Fluorocarbon Rubber s. Nameplate Aluminum 6. Uppef Bushing Stainless Steel ASTM B-473 Alloy 20 7. Liner Options: See Below* 8. Oise Stainless Steel ASTM A-743 Grade CN7M 9. Lower Bushing Stainless Steel ASTM B-473 Alloy 20 10. Body Wafer Ductile Iron ASTM A-S36 11. Body Lug Ductile Iron ASTM A-536 Optional Liners: 0 -- EPDM 1 -- Nitrile (BUNA-N) 2 -- Fluorocarbon 3- Hypalon 4 --- Neoprene Size 2 2 54 3 4 5 6 8 10 12 A 2.15 2.65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS Metal Rubber J B C D EF G H Square 4.0 1.25 5.38 2.62 .38 .312 1.688 1.812 3 25 4.75 1.25 5.88 3.12 .38 .370 1.812 1.938 3.25 5.25 1.25 6.12 3.38 .38 .370 1.812 1.938 3.25 6.75 1.25 6.88 4.00 .38 .403 2.062 2.188 3.25 7.82 1.25 7.38 4.75 .38 .496 2.188 2.312 3.25 8.62 1.25 8.00 5.25 .38 .496 2.188 2.312 3.25 10.87 1.25 9.25 6.50 .50 .560 2.375 2.500 3.25 13.25 1.25 10.50 8.00 m .686 2.688 2.812 4.75 16.0 1.25 12.00 9.25 .50 .748 3.000 3.125 4.75 Size N 2 .500 Vh .562 3 .562 4 .625 5 .750 6 .750 6 .875 10 1.125 12 1.250 O B.C. 3.25 3.25 3.25 3.25 3.25 3.25 3.25 5.00 5.00 Capscrew Data/Stud Data Lug Wafer Approx. Approx. PK L Wafer Lug M Net Wt. Net Wt. Dia. No. Dia. Length Length B.C. (lbs.) (lbs.) .437 4 44-1 lunc 4 IV* 444 7 6 .437 4 44-1 lunc 4% V/t 5% 9 8 .437 4 44-11 unc 4% 154 6 954 854 ,437 8 44-1 lunc 5 144 754 15 12 .437 8 44-lOunc 544 144 854 19 15 .437 8 44-1 Ounc 5V4 2 m 24 18 .437 8 44-1Qunc 5'/, 2'/. 1144 35 29 .562 12 54-9unc m 254 14% 5654 4554 .562 12 '/a-9unc 844 244 17 87 72 NIBCO INC., ELKHART, INDIANA LD 3*33 lug style With Optional Liner and CN7M Disc WD 3*33 wafer style With Optional Liner and CN7M Disc 47 NIBCO000833 250 psi butterfly valves Ductile Iron Body * Extended Neck Geometric Drive Monel Trim Molded-in Seat Liner * Lug and Wafer Sizes 2" through 12" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 MATERIAL LIST Part Specification 1. Stem Monel QQ-N-286 2. Collar Bushing Monet QQ-N-286 3. Stem Seal Fluorocarbon Rubber 4. Body Seal Fluorocarbon Rubber 5. Nameplate Aluminum 6. Upper Bushing Monel QQ-N-286 7. Liner Options: See Below* 8. Oise Monel (Cast) QQ-N-288 Comp. B 9. Lower Bushing Monel QQ-N-286 10. Body Water Ductile Iron ASTM A-536 11. Body Lug Ductile Iron ASTM A-536 Optional Liners: 0 -- EPDM 1 -- Nitrile {8UNA-N! 2 -- Fluorocarbon 3 -- Hypalon 4 -- Neoprene Size 2 2'h 3 4 5 6 8 10 12 A 2.15 2.65 3.15 4.15 5.15 6.15 8.15 10.15 12.15 DIMENSIONS -- WEIGHTS B c D Metal Rubber j EF G H t Square 4.0 1.25 5.38 2.62 .38 .312 1.688 1.812 3.25 4.75 1.25 5.88 3.12 .38 .370 1.812 1.938 3.25 5.25 1.25 6.12 3.38 .38 .370 1.812 1.938 3.25 8.75 1.25 6.88 4.00 .38 .403 2.062 2.188 3.25 7.62 1.25 7.38 4.75 .38 .496 2.188 2.312 3.25 8.62 1.25 8.00 5.25 .38 .496 2.188 2.312 3.25 10.87 1.25 9.25 6.50 .50 .560 2.375 2.500 3.25 1325 1.25 10.50 8.00 .50 .686 2.688 2.812 4.75 16.0 1.25 12.00 9.25 .50 .748 3.000 3.125 4.75 LD 3*44 lug style With Optional Liner and Monel Disc Size N Capscrew Data/Stud Data , Lug Wafer Appro*. Appro*. O PK L Wafer Lug M Net Wt. Net Wl. B.C. Oia. No. Dia, Length Length B.C. (lbs.) (lbs.) 2 .500 3.25 .437 4 %-llunc 4 m 4V. 7 6 2% .562 3.25 ,437 4 %-l 1 unc 4V* iw 5'A 9 a 3 .562 3.25 .437 4 %-tlunc 4% i% 6 m SVi 4 .625 3.25 .437 8 %-11unc 5 IV* m 15 12 5 .750 3.25 .437 8 V*-10unc 5v 1% m 19 15 6 .750 3.25 .437 8 3A-i0unc 5Y* 2 m 24 18 8 .875 3.25 .437 8 W-lOunc 53S 2 VS ii 35 29 10 1.125 5.00 .562 12 7i-9unc 6'/. 2V* 14*4 581# 451# 12 1.250 5.00 .562 12 7/*-9unc 6U 2'h 17 87 72 WD 3*44 wafer style With Optional Liner and Monel Disc 48 NIBCO INC., ELKHART, INDIANA ISIIBCO 150 psi butterfly valves Lug Type Ductile Iron Body * Extended Neck Geometric Drive Angle Disc Molded-in Seat Liner Sizes 14" thru 24" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 MATERIAL LIST PART SPECIFICATION 1. Stem 2. Dust Seal S41600 (Type 418} Stainless Steel Nitrile (Buna-N) Rubber 3. Collar Bushing Bronze 4. Upper Bushing Stainless Steel 5. Stem Seal (3) Fluorocarbon Rubber (Viton*) 6. Disc Ductile Iron ASTM A-395 (Plated) 7. Liner EPDM Rubber- 8. Lower Bushing Stainless Steel 9. Mug Carbon Steel 10. Nameplate Aluminum It Locating Pin N08020 (Alloy 20) Stainless Steel 12. Body Ductile Iron, ASTM A-395/A-536 Trademark El. DuPont Co. "EP0M not suitable tor use with petroleum products (hydrocarbons) and many chlorinated compounds. LD0011/LD-15E-4D lug style With EPDM Liner and Ductile Disc DIMENSIONS -- WEIGHTS Approx. Met Size A 5 C 0 E F 6 H Key Wl 14 13V, 18% 3 13 10% % Vh 3% % 123 16 15% 18% 3 14% 12 h 1% 4 % 190 IB 17% 20% 3 15 13 % 1% 4% % 232 20 19% 22% 3 16% 14 'k 1% 5 % 286 24 23% 26% 3 18% 16% 'k 2% 6 % 477 Size 1 14 3!/ 16 4 18 4"M 20 5% 24 BVn J 6% 6% 6% 6s/. 6% 0P N B.C. Ola. 1% 7% '% 2 Vk "h 2 m nh 2 Vh "Is 2'h Vk K No. 12 16 16 20 20 Cioicrew Date LM Dll. Length 8.C. 1 -Burn 2% 18% 1 -8 urtc 3% 21% 1'/i-7 unc 3% 22% 1%-7 unc 4 25 1%-7 unc 4% 29% NIBCO INC., ELKHART, INDIANA 49 NIBCO000835 150 psi butterfly valves Wafer Type * Ductile Iron Body * Extended Neck Geometric Drive Angle Disc Molded-in Seat Liner Sizes 14" thru 24" 9 Applicable Specifications: MSS-SP67, MSS-SP25, API-609 MATERIAL LIST PART 1. Stem SPECIFICATION S41600 (Type 416) Stainless Steel 2. Dust Seal a Collar Bushing Nitrile (Buna-N) Rubber Bronze 4. Upper Bushing Stainless Steel 5. Stem Seal (3) 8. Disc Fluorocarbon Rubber (Viton*) Ductile Iron ASTM A-395 (Plated) 7. Liner EPDM Rubber S. Lower Bushing Stainless Steel 9. Plug Carbon Steel 10. Nameplate Aluminum 11. Locating Pin N08020 (Alloy 20) Stainless Steel 12. Body Ductile Iron. ASTM A-395/A-538 Trademark E.I. DuPont Co. "EPDM not suitable for use with petroleum products (hydrocarbons) and many chlorinated compounds. WD0Q11/WD-15E-4D wafer style With EPDM Liner and Ductile Disc DIMENSIONS -- WEIGHTS Size A B C 0 E F 14 13V. 16% 3 13 10V. % 16 15% 18% 3 14% 12 % Appro*. Net 8 H Key WL 1% 3% % 99 1% 4 % 136 18 17% 20% 3 15 13 % 1% 4% % 20 19% 22% 3 16V. 14 % 1% 5 % 24 23% 26% 3 18V. 16% % 2V, 6 % 171 225 382- Flmne/Slud Deli 0 P KL M Size 1 J N B.C. OIL Ns. Dla. Length 8.C. 14 3%s 6% 1% 7% >V* 12 1 7% 18% 16 4%. 6% 2 7% "h 16 t m 21V. 18 4"/n 6% 2 7'h 16 1% 9% 22% 20 5%. 6% 2 7% "U 20 1% 10 25 24 6%. 8% 2% 7% h 20 1% 11V. 29% 50 NIBCO INC., ELKHART, INDIANA NIBCO000836 150 psi butterfly valves Lug Type Ductile Iron Body Extended Neck Geometric Drive Angle Disc Molded-in Seat Liner Sizes 14" thru 24" Applicable Specifications: MSS-SP67, MSS-SP25, API-609 f I MATERIAL LIST PART SPECIFICATION 1. Stem 2. Oust Seal S4180Q (Type 416) Stainless Steel Nitrile (Buna-N) Rubber 3. Collar Bushing Bronze 4. Upper Bushing Stainless Steel 5. Stem Seal (3) 6. Disc Fluorocarbon Rubber (Vlton*) Ductile Iron ASTM A-395 (Plated) 7. Liner 8. Lower Bushing Nitrile (Buna-N! Rubber Stainless Steel 9. Plug Carbon Steel 10. Nameplate 11. Locating Pin 12. Body Aluminum N08020 (Alloy 20) Stainless Steel Ductile Iron. ASTM A-395/A-536 Trademark E.t. DuPont Co. LD0111/LD-15B-4D lug style With Nitrite Liner and Ductile Disc 0 tS 1 --f DIMENSIONS -- WEIGHTS Approx. Nit 0, Size A 8 C D E F 6 H Key Wt. 14 13V. 16% 3 13 10% % Vh 3% % 123 16 15% 18% 3 14% 12 % 1% 4 % 190 18 17% 20% 3 15 13 'h 1% 4'A % 232 20 19% 22% 3 16% 14 % 1% 5 % 266 24 23% 26% 3 16% 16% 'k 2% 6 % 477 Size 1 14 3s/* 16 4Vl6 18 4'V* 20 a. 24 m* i 6% 6% 6% 6% 6% 0? N B.C. 3(2. n1% 'V* 2 n *v 2 m "/* 2m Z'h m v K No. 12 16 16 20 20 Cmertw Bata L Dia. Length 1 -8unc 2% 1 -8unc 3% l'/s-7 unc 3% 1%-7unc 4 1%-7 unc 4% M BA 18% 21% 22% 25 29% NIBCO INC.. ELKHART, INDIANA 51 NIBCO000837 IMIBCO '9 150 psi butterfly valves Wafer Type Ductile Iron Body Extended Neck Geometric Drive Angle Disc Molded-in Seat Liner Sizes 14" thru 24" 4 Applicable Specifications: MSS-SP67, MSS-SP25, API-609 MATERIAL LIST PART SPECIFICATION 1. Stem S41600 (Type 416) Stainless Steel 2. Dust Seal Nitrile (Buna-N) Rubber a Collar Bushin} Bronze 4. Upper Bushing Stainless Steel 5. Stem Seal (3) Fluorocarbon Rubber (Vlton") 6. Oise Ductile Iron ASTM A-395 (Plated) 7. Liner Nitrite (Buna-N) Rubber 8. Lower Bushing Stainless Steel 9, Plug Carbon Steel 10. Nameplate Aluminum 11. Locating Pin N08020 (Alloy 20) Stainless Steel 12. Body Ductile Iron, ASTM A-395/A-53S "Trademark El. DuPont Co. WD0111/WD-15B-4D wafer style With Nitrile Liner and Ductile Disc DIMENSIONS -- WEIGHTS Size A 8 C D E f s H 14 13% 16V. 3 13 10% 'h 1% 3V 16 15% 18% 3 14% 12 % IV, 4 18 17V. 20% 3 15 13 % IV, 4% 20 19% 22% 3 16% 14 V, IV, 5 24 23% 26% 3 18V. 18V, 'h 2V, 6 Approx. Net Key Wt % 99 % 136 % 171 % 225 % 362 flange/Stod Pula 0PKL M Size 1 J N BA Dia. No. Ola. Length 8.C. 14 3V* 6% IV, n "/* 12 1 Tk 18% 16 4V 6% 2 Th 'V* 16 1 8% 21% 18 4"/* 6V. 2 7% 16 1% 9V, 22% 20 5% 8V. 2 7% 20 IV. 10 25 24 6%. 6% 2'/! 7% 'V* 20 iv. 11% 29% 52 NIBCO INC.. ELKHART, INDIANA NIBCO000838 N1BCO options and accessories index BALL VALVES Page Acutators: Electric ................................ .........54 Pneumatic........................... .........54 Ball and Stem -- Stainless Steel.......... ........ 54 Handles: Extended Round.................... .........55 Extended Tee.......................... .........55 Locking .................................. .........55 Round..................................... ........ 55 Wing....................................... .........55 Memory Stop......................................... ........ 55 Oxygen Service................................ ... .........54 BUTTERFLY VALVES Actuators: Electric ................................ .........56 Pneumatic........................... ........ 56 Babbitt Sprocket................................... .........56 Operators: Gear..................................... .........57 r Lever-Lock........................... .........57 Stem Extensions.................................... .........56 # NIBCO INC., ELKHART, INDIANA 53 NIBCO000839 ball valves options and accessories Stainless Steel Ball and Stem 316 stainless steel ball and stem are available on most NIBCO ball valves. Oxygen Service Most NIBCO ball valves are available for oxygen kih vice preparation. Cleaned and packaged in durable heat-sealed plastic bags to avoid contamination Oxygen cleaned valves are not recommended lor prim sures exceeding 50 psi. Electric Actuator/Pneumatic Actuator 54 NIBCO INC., ELKHART, INDIANA NIBCO000840 IM1BCO ball valves options and accessories Handle Options ---- m- A wide variety of low-carbon steel handles is available to fulfill safety and operational requirements in various processing and manu facturing industries. The lever handle with plastic cover is standard. Other handle options are shown at right. Stainless steel lever handles are avaiiable, as an option, also with plastic cover. If an optional handle is desired, please indicate which one when ordering. Lever Wing Round CD Round Extended Extended Tee Handles Available for NIBCO ball valves. T-handle provides a full two-inch clearance above piping to ailow easy installation of insulation covering. Open-neck design allows adjustment of stem pack ing. Memory stop feature allows valve to be closed and reopened to same pre-set position. Memory Stop With memory stop the NIBCO ball valve can be opened to the same pre-set position each time. Made of sturdy steel, the memory stop can be supplied with the 580,585,590 and 595 series ball valves. Specify by adding -M to figure number, i.e. T-580-M. A kit is available for field installation, which includes pre tapped handle, screw, and memory plate. NIBCO INC., ELKHART, INDIANA 55 NIBCO000841 IM1BOO butterfly valve options and accessories # Adjustable Sprocket 0i*. of Sprocket Size Wheel Mo, In Inches 04 1 SVt m 7Vi 29 2V4 12% 3 im 3VS 19 4 22 Weight in Lbs, 2 4 5 8 15 21 25 34 me, of Valve Rim Will Pit 2 to 4 4>/ 10 554 6 to m 73A to 9 9'A to 12# 12% to 15% 15j/ to 19 19 Vi to 22 Chain Size No. 2 1/0 1/0 1/0 4/0 4/0 4/0 5/0 Chain Weight per ier in Lbs, 10 m 17% 17V* 30 30 30 35 The Babbitt Adjustable Sprocket Rim will provide for remote operation of gate, globe, angle and butterfly valves in high, normally out-of-reach locations- Attaches to valve wheel for Instant valve open/close response. Sprocket rim made from cast iron, chain guide is malleable iron. When ordering specify either the sprocket and chain number or the NIBCO valve figure number and size. The chain length must also be specified. DUCTILE SPROCKET RIM OUCTIL6 SPROCKET RIM PLATE guide arm Stem Extension Stem extension for butterfly valves -- available In lengths up to 10 feet to provide means of operation at a required distance away from the valve body. Manual or power operated actuators are easily adapted to mounting flange on the extension housing. For stem extension in excess of 10 feet -- consult factory. Actuators -- Electric & Pneumatic Electric and pneumatic actuators for on-off control -- used whenever automatic or remote control operation is required. Both types are available for the full size of NIBCO Butterfly valves. k Pneumatic-- Air to air or spring return designs are available. Options include electric sole noids, switch boxes, positioners, and lighter pressure springs. Air supply of 40 to 120 PSI may be used. Electric -- available in NEMAIV and NEMA VII (explosion proof) enclosures. 120 or 220 volt, single phase, 60 cycle service. Options such as throttling, different cycle times, and special controls are available. 58 NIBCO INC., ELKHART, INDIANA NIBCO000842 |ryiBcpoj engineering data index Page Flange Dimensions ...........................................66 Flow Data .................................. 64-65 Pressure/Temperature Charts ..........................67 Property of Materials ............................... 60-63 Pipe Dimensions .............................................. 70 Specifications ................................................... 59 Technical Information -- Butterfly Valves Torque Requirements....................................... 68 Resilient Seat Materials ....................................69 58 NIBCO INC., ELKHART, INDIANA NIBCO000843 specifications NIBCO Ball and Butterfly valves are designed and manufactured to give maximum performance on recommended service at the lowest possible initial and upkeep cost They meet or exceed the following specifications developed through years of experience, research and many laboratory tests. Ball Valves Federal Specification WW-V-35B Type: II -- Stationary seat ring and floating ball. Classes: A - Copper Alloy C - Corrosion Resisting Steel D - Carbon Steel Styles: 1. Valve design which permits inspection and repair of seats and seals without removing the valve body from the line. 3. Valve design which requires the valve to be removed from the line for either inspection or repair. Butterfly Valves American Petroleum Institute Manufacturers Standardization Society of the Valve and Fitting Industry, Inc. API 609 MSS-SP-67 NIBCO INC., ELKHART, INDIANA 59 NIBCO000844 IMIBCO properties of valve materials ALLOY Die Cast Aluminum Free Cutting Brass Navy "M" (Steam Bronze) Composition Bronze (Ounce Metal) m Copper-Silicon Alloy B s Forging Brass o 8 Brass Wire (Red Brass) g Leaded Red Brass 2 m Aluminum Bronze (Cast) Aluminum Bronze (Rod) Silicon Red Brass Leaded Semi-Red Brass Leaded Red Brass Copper (Wrought) ASTM NO. B-85 B-16 OTHER ALLOY DESIGNATION UNS-A03800 UNS-C36000 AL 87 NOMINAL OR MAX. CHEMICAL COMPOSITION CARBON CHROME COBALT COPPER IRON C Or Co Cu Fe LEAD Pb MANOANtM Mn w mm m 1.0 1.3 35 61.5 3.0 B-61 UNS-C92200 .005 88.0 .25 1.5 8-62 B-98 8-124 B-134 B-140 UNS-C83600 UNS-C65100 UNS-C37700 UNS-C23000 UNS-C31400 .005 85.0 96.0 60.0 85.0 89.0 .30 5.0 .8 .05 .3 2.0 .05 .05 .10 1.9 t 8-148 B-15Q 8-371 UNS-C95400 UNS-C64200 UNS-C69400 11.0 7.0 85.0 4.0 91.0 .30 .05 .10 81.5 .20 .30 B-584 UNS-C84400 .005 81.0 .40 7.0 UNS-C84500 .005 78.0 .40 7.0 B-75 UNS-C12200 99.9 Gray Iron 3% Ni Grey Iron Austenitic Grey Iron (Ni Resist) Ductile Iron (Ferritic) Austenitic Ductile Iron (Ductile) (Ni-Resist) A-126 - Class B A-126 -- Class B Modified A-436 -- Type 2 A-395 A-S36 A-439-D2C 3.00 2.0 3.20 2.9 .5 .5 1.0 2.4 Copper iron 60 NIBCO INC., ELKHART, INDIANA NIBCO000845 IMIBCO properties of valve materials MS 1 NICKEL & Nl IT .50 NOMINAL OR MAX. CHEMICAL COMPOSITION PHOS SILICON SULFUR P SI S TIN Sn TITAN IUM Ti TUNG STEN W 12.0 .15 w>: m 1; i-o p**` % S 1i0 if -7 .05 .005 .05 6.0 .05 .005 .08 5.0 1.6 ZINC Zn ,50 35.5 4.5 S.O 1.5 38.0 15.0 9.1 .25 2.0 4.0 .20 .02 .005 .08 3.0 1.0 .02 .005 .08 3.0 .50 14.5 9.0 12.0 NOMINAL PHYSICAL PROPERTIES TENSILE STRENGTH Psi YIELD STRENGTH Psi % ELONGATION HARDNESS 42,000 19,000 3.5 50,000 20,000 15 75 Rw B 34,000 16,000 22 65 BHN 500 kg 30,000 14,000 20 60 BHN 500 kg 50,000 20,000 11 65 Rw B 52,000 20,000 45 80 Rw B 56,000 60 Rw B 50,t0 30,000 7 60 Rw B 75,000 30,000 12 170 BHN 3000 kg 90,000 45,000 9 80 Rw B 80,000 40,000 15 85Rw8 29,000 13,000 18 55 BHN 500 kg 29.000 13,000 16 55 BHN 500 kg .02 3.00 20.0 .75 .75 2.0 .08 2.50 .15 .15 .12 36.000 31,000 31,000 25,000 60,000 30,000 25 40,000 18 45 T 30,000 kg 195 195 118 167 ^24.0 .08 3.0 58,000 28,000 20 146 NIBCO INC., ELKHART, INDIANA NIBCO000846 properties of valve materials # ALLOY Wrot 304 Cast 316 ASTM NO. A-167-304 A-351-CF8M OTHER ALLOY DESIGNATION UNS-S30400 UNS-S31600 Cast 316 Cast 316 d> m Wrot 316 Cast 410 m Forged 410 IE Wrot 410 s Wrot 416 tf) Wrot 420 A-743-CF16F A-743-CF8M A-276-316 A-217-CA15 A-182-F6A2 A-276-410 A-582 A-276-420 UNS-S31600 UNS-S4100 UNS-S41600 UNS-S42000 Cast Alloy 20 Wrot Alloy 20 A-743-CN7M B-473-20C63 UNS-N08020 Wrot 17-4PH A-564-630 UNS-S17400 Forged Carbon Steel Cast Carbon Steel A-105 A-216-WCB 1<D I'A Cast Cr. Moly Steel 55 Cast Cr.-Moly Steel Cast Low Carbon Steel Nickel-Low Carbon Steel A-217-WC6 A-217-C5 A-352-LC8 A-352-LC2 8-7 Alloy Steel Studs 304 S.S. Nuts A-193-B7 A-184-GR8 2-H Alloy Steel Nuts Reg. Steel Bolting m VCJ Steel Bolting 304 S.S. Bolting A-194-2H A-307-Gr, B A-449 A-493-304 UNS-S30400 E Eyebolts p Gland Nuts H/WNuts Swing Bolt Pin Yoke Bushing Caps Seat Ring Base A-489 A-563-Gr, A A-108-1020 A-108-1212 A-108-12L14 A-519-1026 UNS-G10200 UNS-G12120 u. AWS 5.13 (Trademark Materials like. Stellite 6*. Stoody 6. and Wallex 6.) 'Trademark by Cabot Corp. 1 sco Cast Monel Wrought Monel (K-500) QQ-N-288-E QQ-N-286-C1B NOMINAL OR MAX. CHEMICAL COMPOSITION manic; a MOlfP CARBON CHROME COBALT COPPER IRON At. C Cr Co Cu Fe LEAD Pb Nt sr Mn Mm .08 19 .08 20 :> t *. ' * ,16 20 .08 20 .08 17 .15 13 1 !> i ' su y ;> *, 1 .15 13 .15 13 .15 13 .15 13 .07 20 .07 20 3.5 3.5 i i i ;:* -- iw i; ? *1 .07 16 3.5 \ .35 .3 .2 1.2 .2 5 .3 .25 .4 1 .08 19 i ti 7 .... 5!) V. 1.0 .65 .85 '> 2 .4 .2 .45 .4 .08 19 .6 2 .48 .37 .55 .35 1.0 1.0 .20 .45 .13 .85 .15 .25 1.25 29 55 .25 1.0 .75 A2.5 w .5 .3 3.0 .1 30 3.5 24 2.0 1,5 1.5 62 NI8C0 INC., ELKHART, INDIANA NIBCQ000847 NIBCO000848 flow data Cv Values for Valves Fig. Nos. GATES S&T-22 S & T-180 S & T-111-113-131-133 134-135-136-174-176 (T & F-617-619-667-669 607-609) {CS-102-103 302-303-602-603) (F-637-639-DI-102) GLOBES S & T-211 (BWV)-235Y 275Y T-275-B , F-718-(CS-132-133 332-333-632-633 (738) CHECKS S & T-413-433-473 (Swing) S & T-480 (Poppet) F-908 (Swing) T & F-918-968-938 (Swing) W-900-W (Wafer) W-F-910-960 (Poppet) BALL T-560 (Br-CS-SS) T-570 F & S & T-580-590 T & S-580-BH K & S & T-585-595 BUTTERFLY LD&W0 W & L (D-15-E-40) Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv Cv VALVE SIZE V. V* V, % V- 1 I'/- Vh 2 2% 3 3'A 4 5 .5 2 4.9 9.1 22 -- 5.6 10.7 17.6 32 40 50 65 95 95 130 175 220 -- 5.6 10.7 17.6 32 54 97 135 230 337 536 710 960 1.525 2.250 215 335 510 710 945 1.525 2.25n .61 1.16 2.21 3.64 6.85 11.1 -- 1.16 2.21 3.64 6,65 11.1 20 20 28 28 48 70 111 -- 198 48 70 111 Aw 45 70 105 ___ 195 315 465 _ 1.3 ---- 2.5 4.8 14.3 24 3.70 6.86 16.3 30 43 60 49 72 102 150 238 315 465 675 1,000 130 150 243 356 -- 665 1,073 1,584 137 221 327 -- 330 ._ 605 -- 500 -- 595 975 1,440 806 1,200 950 1,400 _ 4.0 4.0 4.9 11.7 22 ---- -- 5.2 12.9 24 ---- _ 5.84 13.9 27 -- 4.3 6.2 9.1 21 32 -- 5.9. 11.4 18.7 34 57 35 52 37 58 44 64 45 68 103 143 95 97 100 183 390 110 245 310 135 225 340 - 660 1,080 64 NIBCO INC., ELKHART, INDIANA NIBCO000849 Liquid Plow. ` Q ** Cv IMIBCO where .., Q = flow rate {gallons per minute) AP * pressure drop across valve (psi) S * specific gravity of media This equation Is good for turbulent flow and for liquids with viscosities near that of water. (Cv is defined as the flow in GPM that a valve will carry with a pressure drop of 1.0 psi when the media is water at 60 F.) Gas Flow: Q = 1360 C.v 'AP x Pi ST where... Q = gas flow (SCFH--std. cu. ft/hr) S = specific gravity of gas (air = 1.0) T = temp--degress Rankine (F + 460) AP = pressure drop across valve (psi) Pi = upstream pressure (psia) absolute NOTE: AP must be less than .5 Pi. (Flow is critical when AP is greater than .5 Pi.) (THROTTLING FACTORS) For throttling use with disc partially open. Multiply Cv by factor. Note: Gate valves are not throttled. Percent Open I- 8 10 12 14 16 18 20 24 1 0 10 20 30 40 SO 60 70 80 90 100 fr I $ | 4150 6,700 9,925 13,800 18,375 23,600 29.600 43,570 L 860 1,390 2,93? 4,730 6,985 2.670 2,200 2.600 4,300 3,550 4,175 6,350 5,250 6,150 8,575 11,400 0 ,35 .65 .90 .93 .96 .98 .99 1.00 1.00 1.00 0 .03 .035 .06 .1 .16 .24 .32 .47 .68 1.00 0 .35 .65 .90 .93 .96 .98 .99 1.00 1.00 1.00 WARNING The Fluid Flow factors contained herein are calculated values. They are therefore approximations and cannot be used for highly critical flow or pressure drop calculations. For very precise flow measurements, tests must be conducted on any valve mentioned within this catalog. Ball & Butterfly Valves Degrees of Open 0 10 20 30 40 45 50 60 70 80 90 0 .01 .05 .16 .30 .37 .45 .58 .71 .87 1.00 0 .01 .05 .16 .30 .37 .45 .58 .71 .87 1.00 0 .01 .05 .16 .X) .37 .45 .58 ,71 ,87 1.00 #0 5.300 7,969 0 .03 .06 .12 .18 .22 .27 .40 .56 .80 1.00 9.500 13,000 18,000 22.500 32.600 0 .03 .06 .12 .18 .22 .27 .40 .56 .80 1.00 NIBCO INC., ELKHART, INDIANA 65 NIBCO000850 IMIBGO flange dimensions Class 150 Flanges -- ANSI-B16.5 Vie" Raised Face Mate with 125 lb. Cast Iron Flanges -- ANSI-B16.1 DIMENSIONS IN INCHES Diameter Thickness Diameter Balt Number Diameter length al of al Bell Hole of of of SIM Flange Flange Circle diameter Bolts Bolls Stud Bolls a 6 % 4% % 4 % 3V. 2% 7 "/ 5% % 4 % 3% 3 Vh % 6 % 4 V. 3*/. 3% m % 7 % 8 % 3% 49 Vh % 8 V, 3% 5 10 '* 8% '/ 8 Vi 4 6 11 1 9% % 8 % 4 8 13% 1% 11% % 8 % 4V. 10 16 Vh 14V. 1 12 % 4% 12 19 1% 17 1 12 % 4% 14 21 1% 18% IV. 12 i 5% 18 23% Vh 21% IV. 16 i 5% 18 25 w* 22% Vh 16 1V 6 20 27% 1"/. 25 IV. 20 iv. 6% 24 32 1% 29V; 1% 20 Vh 7 NIBCO INC., ELKHART, INDIANA NIBCO000851 pressure/temperature ratings Bali Valves 400, m 4E li? f i%' 300 ':4vV-* it vii- ?-<4 1 ? 200 "a '> s- - ' . Vor SBC and 585 3ronze Bail V lives V yj- \\ \V. 150 psi Sati rated - -'Ji' \Ste< m 580 ' 'A`* -r. VoE \- 125 p si Sati rated steam100 1 -E'.' . , ' "3 -20 0 100 200 Temperature, F 300 400 -20 100 200 Temperature, F 300 400 2,000, T-560 ;CS'&S6 Vi"-2" T-571 -CS W-1" T-581 -CS & $6 V"-1 For T-560,'570 an< osu w tn TGFig=ssS-<Rtaetsiiifor ;ed 1For 590 and 595 CS an i S Ba 1 Velive 3 -V4"-2" K & T-i590- CS 1,500 -CS V/* "-2` -CS &s 6 a. <o \ k ` .* \ \ 600 500 f'X-t. '3i"-2 i-s60' 400 > W IS P'Z -t\,, * - 3k .i*M,zSr "~u. a?/ gf V:*S .'is Jp! ISaturi tec Ste a'ni ' IE - figti "i" -20 0 100 200 300 Temperature, F 400 1500 V) CL 1400 \ V4''-2"'k & T-590-J-S6 \ I ---i---- i \ v14"-2 K & t-:595- CS 0> 3 1300 tfi 3vn oj 1200 \ CL 1100 Kl T- 595 -S6 with Glass-Re inf( rced 800 TFE Sfpats I \700 J600 \ s, \ \500 f-5 0-E Ft 8 \400 ith. \\ SN300 s\j200 T.ESe. its r: *? .4* <5 y" \ 100 0 15()ps ISaturs ted Ste am 3? a ivj `X A`> ,' i V -20 0 100 200 300 400 1000 900 800 700 600 500 400 300 200 100 0 -20 0 \\ \ S \s, \\ \\ 100 200 300 400 Temperature. F Temperature, F Butterfly Valves F-590-S6 F-590-CS -20 to 100F 275 285 TEMPERATURE 200 F 300F 240 215 260 230 400 F 195 200 LINER TEMPERATURE RATINGS Seat Material EPDM Nitrile (Buna-N) Fluorocarbon (Viton) Temperature -20F to + 225F -20F to + 180F -20F to + 300F Seat Materia! Neoprene Hypalon Temperature -20F to + 180F -20 F to + 200'F 67 NIBCO000852 riviBca] < butterfly valve technical information butterfly valve torque requirements OPERATING TORQUE / INCH-POUNDS 50 PSI 100 PSI 150 PSI 200 PSI 250 PSI Size Dry Wet Dry Wet Dry Wet Dry Wet Dry Wet 2" 225 175 250 190 290 225 295 230 300 235 2V4" 280 215 315 240 355 275 375 285 395 300 3" 360 275 390 300 435 350 440 370 450 390 4" 550 420 600 470 675 525 730 565 780 600 5" 850 520 900 570 950 620 975 645 1,000 670 6" 1,000 800 1,100 900 1,300 1,000 1,450 1,100 1,600 1,200 8"' 2,400 1,400 2,600 1,600 2,800 1,800 2,900 1,900 3,000 2,000 10"* 4,100 2,450 4,400 2,750 4,700 3,050 4,850 3,200 5,000 3,350 12''* 5,500 3,200 6,000 3,700 6,500 4,200 6,750 4,450 7,000 4,700 14" 7,600 4,600 8,400 5,400 9,200 6,200 9,600 6,600 10,000 7,000 16" 11,400 7,400 12,600 8,600 13,800 9,800 14,400 10,400 15,000 11,000 18" 14,000 9,000 16,000 11,000 18,000 13,000 19,000 14,000 20,000 15,000 20" 17,500 11,000 20,000 13,500 22,500 16,000 23,750 17,250 25,000 18,500 24" 24,000 15,000 28,000 19,000 32,000 23,000 34,000 25,000 36,000 27,000 Torque is the force that produces rotation when operating a butterfly valve. The rotary force required to operate a butterfly valve is affected by several factors such as length of time in service, frequency of operation, type of liner material and service conditions. All these factors combine to make up three main classes of torque--seating or unseating torque, bearing friction torque, and dynamic torque, which comprise what is known as shut-off or break-away torque. The values given above are a total of seating or unseating torque and bearing friction torque at a given pressure differential. In sizing an-actuator, these values are used since they are the highest torques required to operate the valve under normal conditions. A safety factor has been added to these values. * Before specifying lever-lock operation on these sizes, ensure that the valve can be operated with reasonable effort. Butterfly valves, sizes 8" and larger, when used on liquids, show a marked increase in dynamic torque which tends to close the valve. For this reason, gear operated or actuated valves are recommended. 68 NIBCO INC., ELKHART, INDIANA NIBCO000853 butterfly valve technical information Resilient Seat Materials EPDM -- EPDM is a terpolymer elastomer made from ethylene-propylene diene monomer. EPDM has good abrasion and tear resistance and offers excellent chemical resistance to a variety of acids and alkaiines. It is susceptible to attack by oils and is not recommended for applications involving petroleum oils, strong acids, or strong alkaiines. It has exceptionally good weather aging and ozone resistance. It is fairly good in ketones and alcohols. BUNA-N (NITRILE) -- BUNA-N is a general purpose oil resistant polymer known as nitrile rubber. Nitrile is a copolymer of butadiene and acrylonitrile. BUNA-N has good solvent, oil, water and hydraulic fluid resistance. It displays good compression set, abrasion resistance and tensile strength. BUNA-N should not be used in highly polar solvents such as acetone and methyl ethyl ketone, nor should it be used in chlorinated hydrocarbons, ozone or nitro hydrocarbons. Fluorocarbon (VITON*) -- Fluorocarbon elastomers are inherently compatible with a broad spectrum of chemicals. Because of this extensive chemical compatibility which spans considerable concentration and temperature ranges, fluorocarbon elastomers have gained wide acceptance as a material of construction for butterfly valve O-rings and seats. Fluorocarbon can be used in most applications involving mineral acids, salt solutions, chlorinated hydrocarbons and petroleum oils. It is particularly good in hydrocarbon service. Fluorocarbon (VITON*) is not suitable for steam service. NEOPRENE -- Neoprenes were one of the first synthetic rubbers developed. It is an all purpose polymer with many desirable characteristics. Neoprene features high resiliency with low compression set, flame resistance, animal and vegetable oil resistance. It is principally recommended for food and beverage service. Generally, neoprene is not recommended and is attacked by strong oxidizing acids, most chlorinated solvents, esters, ketones, aromatic hydrocarbons and hydraulic fluids. Neoprene is not generally affected by moderate chemicals, fats, greases, and many oils and solvents. HYPALON* -- Hypalon has very good resistance to oxidation, ozone and good flame resistance. It is similar to neoprene except with improved acid resistance where it will resist such oxidizing acids as nitric, hydrofluoric, and sulfuric acid. Abrasion resistance of neoprene is excellent, about the equivalent of the nitriles. Oil and solvent resistance is somewhat between that of neoprene and nitrile. Salts have little if any effect on hypalon. Hypalon is not recommended for exposure to concentrated oxidizing acids, esters, ketones, chlorinated, aromatic and nitro hydrocarbons. Not to be used in steam service. 'Trademark of E. I. Dupont Co. NIBCO INC., ELKHART, INDIANA 69 NIBCO000854 NIBGO pipe dimensions ,-> Nominal Outside Pipe Diem. Size TABLE 5 Pipe Dimensions in Inches Dimensions shown conform to ANSI B36.10 (Wrought Steel and Wrought Iron Pipe). Wall Nominal Wall TWctawt and Inside Diameter 10. Schedule Schedule Schedule Standard Schedule Schedule Extra Schedule Schedule Schedule Schedule Schedule to 20 30 Weight 40 60 Strong *0 100 129 140 160 Dbl Ex. Strong Wall .068 .068 .095 .095 1.0. .540 watt I.D. wall .269 .269 .088 .088 .364 ,384 .091 .091 .215 .215 jig .119 .302 .302 .126 .126 l.D. .840 Wall l.D. .493 .493 .109 .109 .622 .622 .423 .423 .147 .147 .546 .546 .187 .294 .4 .252 1.315 1.900 2.875 Wait 1.0. Wall !.D, Walt 1.0. Wall 1.0. Wall l.D. Wall l.D. .113 .824 .133 1.049 .140 1.380 .145 1.610 .154 2.067 .203 2.469 ,113 .824 .133 1.049 ,140 1.380 .145 1.610 .154 2.067 .203 2.469 .154 .742 .179 .957 .191 1.278 .200 1.500 .218 1.939 .276 2.323 .154 .742 .179 .957 .191 1.278 .200 1 500 .218 1.939 .276 2.323 .218 .614 .2 .815 .2 1.1 ,1 1.3 .343 1.689 .375 2.125 .308 .434 .3 .599 ,2 .896 .4 1.1 .436 1.503 552 1.771 3.500 4.000 4.500 Wall 1.0. Walt l.D. Wall l.D. .216 3.068 .228 3.548 .237 4.026 .216 3.068 .226 3.548 .237 4.026 .300 2,900 ,318 3.364 .337 3.826 .300 2.900 .318 3.364 .337 3.826 .4 3.624 .438 2.624 .600 2.300 .531 3.4 .674 3.152 5.563 Wan 1.0. Wall ,258 5.047 .280 .258 5,047 .280 .375 4.813 .432 .375 4.813 .432 .500 4.563 ,2 .625 4.313 .718 .7 4,063 4 1.0. 6.065 6.065 5.761 5.761 5.1 5.189 4.897 8 8.825 Wall l.D. .250 8.125 .277 8.071 .322 7.981 .322 7.981 .406 7.813 .500 7.625 .500 7.625 .593 7.439 .718 7.189 .812 7.001 .906 6.813 .875 6.875 Wall l.D. .250 .307 .365 .385 10.250 10.136 10.020 10.020 .500 9.7 .500 9.7 .593 9.564 .718 9.314 .843 9,064 1.000 8.7 1.125 8.500 12.750 Wall l.D, .250 .330 .375 .406 .562 .500 .687 .843 1.000 1.125 1.312 12.250 12.090 12.000 11.938 11.626 11.7 11.376 11.064 10.7 10.500 10.1 14.00) Wall .250 .312 .375 .375 .438 .593 .500 .7 .937 1.093 1.2 1.406 l.D. 13.500 13.375 13.250 13.250 13.124 12.814 13.000 12.500 12.126 11.814 11.500 11.1 16.000 Wall .250 .312 .375 .375 .500 ,6 .500 .843 1.031 1.218 1.4 1.593 l.D. 15.500 15.375 15.250 16.2 15.000 14.688 15.000 14.314 13.938 13.564 13.124 12.814 18 18.000 Wall .250 .312 .438 .375 .562 .7 .500 .937 1.1 1.375 1.2 1.781 l.D. 17.500 17.375 17.124 17.250 16.876 16.500 17.000 16.126 15.688 15.2 14.876 14.4 20 20.000 Wall .250 .375 .500 .375 .593 .812 .500 1.031 1.281 1.500 1.7 1.968 1.0. 19.500 19.250 19.000 19,2 18.814 18.376 19.000 17.938 17.4 17.000 16.500 16.064 24 24.000 Wall .250 .375 .562 .375 .687 .968 .500 1.218 1.S31 1.812 2.062 2.343 1.0. 23.500 23.250 22.875 23.2 22.626 22.064 23.000 21,564 20.9 20.376 19.876 19.314 AH dimensions given in inches. The wall thicknesses shown represent nominal or average wall dimensions which are subject to a - l2Yt% mill tolerance. 70 NIBCO INC., ELKHART, INDIANA NIBCO000855 fmew-. m FITTINGS BRONZE AND IRON BODY PRESSURE-RATED VALVES NIBCO000856