Document G5dbMrdbvOeqwzB1NqzXX55rv

PLAINTIFFS JMMC-261' Standardized Mechanical Joint Cast Iron Pipe and Fittings (Revised, 1950) UNITED STATES PIPE & FOUNDRY CO. General Office: Birmingham, Ala. \ Standardized Mechanical Joint Cast Iron Pipe and Fittings (Revised, 1950) UNITED STATES PIPE & FOUNDRY CO. General Office: Birmingham, Ala. Plants: Bessemer (Ala.)? Birmingham (Ala.), Burlington (N. J.), Chattanooga (Tenn.), Decoto (Calif.). District Sales Offices: Burlington, New York, Boston, Pittsburgh, Birmingham, Kansas City, Houston, Dallas, Chicago, Cleveland, Minneapolis, San Francisco, Los Angeles, Seattle, Syracuse ,General Specifications for mechanical joint cast iron pipe fittings and accessories Pipe shall be cast iron produced centrifugally in sand lined or metal molds, horizontally in green sand molds or by the pit cast method. Each pipe shall be provided with a mechanical joint socket on one end and the other end shall be plain. Fittings shall be provided with sockets at all openings unless specifically ordered otherwise. Three to twelve-inch fittings conform to A.S.A. Specification A-21.10 (for short body fittings) and joints conform to A.S.A. Specification A-21.11 (for mechanical joints). Pipe shall be tested in a suitable hydraulic press to the pressure indicated in the appropriate pipe specification. Pipe and fittings shall be furnished-to dimensions as tabulated. All sockets and plain ends shall be checked with ring and plug gages. Pipe and fittings shall he furnished uncoated and unlined unless otherwise specified. If coatings are required they shall meet specifications agreed upon by the purchaser and seller. All joint surfaces shall be protected by suitable means at the foundry against corrosion during storage and shipment. High strength Cast Iron Tee Head Bolts and Hex Nuts shall be furnished in sufficient quantities to provide for each socket opening on pipe and fittings. These bolts shall have a minimum tensile strength of 50,000 pounds per square inch. Cast Iron Glands shall be furnished in sufficient quantities to provide for each socket opening on pipe and fittings. These glands shall be made of high strength Cast Iron. Gaskets shall be furnished in sufficient quantities to provide for each socket opening on pipe or fittings. The type of gasket shall be as stipulated in sales con tract. 17 i 1 1 ,Weights and Dimensions of mechanical joint cast iron pipe fittings and accessories Fittings and all accessories for mechanical joint cast iron pipe are standardized and interchangeable regardless of which member, or members, of the Cast Iron Pipe Research Association they are obtained from. Association members have devoted many years of research, involving the test ing to destruction of hundreds of specimens, to the improvement of design and strength factors of fittings. On the pages following are shown cross-sectional drawings and Tables of Weights and Dimensions of Pipe; Bends; Tees and Crosses; Reducers; Sleeves; Glands, Plugs and Caps; Connecting Pieces; Offsets and Drip Pots. All fittings are made to dimensions, as shown in the Tables, of high quality cast iron and are rigidly inspected and tested. They are furnished with sockets at all openings unless otherwise specified. Socket dimensions of pipe and fittings are the same. Joint surfaces are protected against corrosion during storage and shipment. Fittings are furnished uncoated and unlined unless otherwise specified. For further information, refer to General Specifications for Mechanical Joint Cast Iron Pipe, Fittings and Accessories on page 17. For information regarding Gaskets, Bolts and Glands please turn to page 32. 19 14- 48" GLANDS ONLY i W eight o f B ell, lb . W eight o f ! i S ize B olts and 1 P ipe and G asket, F ittin g s lbs. G land, ts o N o s 00 SOI NNo a ts P it C ast HM M a n O ts ft ts oo N 3 Ots a ts 9 I W _____________________ CM NOISN3WIQ 9N01 ^ KI P it Cast P ipe a n d F ittin g s K2 P it Cast P ipe and F ittin g s u Q(U M NN O n 5 R o N N ftss a m oN 3 4X Mn N N J s $ ** sS Ss S S 55 6 * * N N Z & sS MMMM oN s s N N O--Nin 2i3 SR 2R N N00 NO MOO N-HNO mO N mNN o o N r* r' f * f * f * f ` fa N u o*tsr l 0*0 f ss$ 1 O f` NN f' No f 00 M 90 f` oN f' O0 N OO ,*M 0000 oo f*5 N N 3 M a. S R Ps ts N !? R s R R R O o o O g o N N n M rt N N N N N N tNt N S 2 OON r' ON f o r' OB oo f- oo fa o*o as f-3 Nm MN 1^ NmN f" 25 fa NMU) o N O N O N o o N J 03O* r' O OO I- otoo 1*^ 00 N < f" 00-O fa ON fW NMMN fJ N MN f-3 Nm*2t f NMO f^ NMN fa M O N O N o o N N--O\D I'^ NN 7* NN fa N-- N fd N1MN fd NN fd as IS N M fN N JO 7s 2g l'ft MU) *N N ON O N N O s N--O I**3 NN 7rf NN fd as i`a NwO f N >^o fd NM MN IS NMU) f1 NN 23 fa M9 f1 tNs M00 fa 1N N O N N S o s il 4) CWfi*, N f^ oo f* tfi OO fa i-i id gs fa fd 8S f N SS fs SR i'S co o o f ts 1N CO O 1N N ON o N N o 3 9 -i m o o o ON o oo gs ts OO SS in o o a N Hi10' Hirf -Ha .HIS Hi2 His His nia nia HiS N 9 O ts o f g gx gX gx gx * S l^\ o sf* is 3sss M ++ ++ +++++++ . 0N0 N O S NCD s o S 0N oo s S s oN oO N N s & N + .0 7 -.0 3 9.15 rt'O Noo NO (< r* ts O r* rs f^ In. O N Of>N tSTP *3* S3 ftS ftS NO^Oi ts ts ft fa N fd N IS o i'Es o IS l`s o i'a N N N 3 O + .0 7 -.0 5 + .0 7 -.0 5 + .0 7 - .0 5 + .0 7 --.05 + .0 7 --.05 + .0 7 - .0 5 +++ +++++++ 22.84 18.64 16.54 Tf9 oo nfN o -- iOf NN ioJiriSo* Tp if ^ ?ts S3 ts o N Q o f f fs fd fa o o f N ts l"rS ts NN ON 'J* N O +++++ 00 N O N O K o o 00 o 3 s" + ON fa o 16.40 18.50 ++ 26.90 22.70 a O ots O q NN oN d + .0 7 --.05 + .0 7 -.0 5 20.60 + .0 6 --.04 12.22 H -H H + | m oin O O o o % o in O s N N N N N N N N N N N aaaa o COO O o O S ss S? < N V o O o o s" N "* O i'S s fft -H fl H -H ii H + + + .0 5 -.0 8 19.50 S3 o s N i'S fa o d N 3 ++ w N 0B N s N N 3 % Xoa ai Si rESS 3 go Eg g" XW n-- --3 Coo Xa vw xW.2M VO i .3Ob--u Va. *cc3 ogc 2i"3 3S n : >* ? bw a_ si I 15eS= S| . "O 0. ` 2ES41 . ba ! f'o id'S ! o| s Q x 2w tCIS8 w ft) Q. i &E | Is ill \n 3(O*ft). coo *"T ^*H0* ,I WCX ao n ou i o J \6Ji <0 o ! " g J5 Nij; ^QF .X . > < 1 4 0 0 _____ 1 STANDARD THICKNESSES AND WEIGHTS OF CAST IRON MECHANICAL JOINT PIPE CENTRIFUGALLY CAST IN METAL AND SAND LINED MOLDS -FOR WATER AND OTHER LIQUIDS Note: Thicknesses in accordance with A.S.A. Specifications, 18,000 psi full length bursting tensile, 40,000 psi ring modulus of rupture. For pipe laid without blocks on flat bottom trench with tamped backfill under 5 feet of cover. For other conditions consult the manufacturer. Thick Size ness ins. ins. Outside Diam. ins. 3 .32 3.96 4 .35 4.80 6 .38 6.90 8 .41 9.05 10 .44 11.10 12 .48 13.20 14 .48 15.30 16 .54 17.40 18 .54 19.50 20 .57 21.60 24 .63 25.80 30 .79 32.00 36 .87 38.30 42 .97 44.50 48 1.06 50.80 12 ft. Lgth.* Avg. per ft. per Lgth. Weight Based On 16 ft. Lgth.* 161^ ft. Lgth.* Avg. per ft. per Lgth. Avg. per ft. per Lgth. 12.3 16.6 26.1 37.2 49.3 64.0 76.2 97.1 109.8 128.7 170.2 Class 50--50 Lb. Pressure--115 Foot Head 150 200 315 445 590 770 915 1165 1320 1545 2040 12.2 16.4 25.7 36.7 48.5 62.9 74.6 95.0 107.5 125.9 166.5 259.5 343.9 445.7 195 260 410 585 775 1005 1195 1520 1720 2015 2665 4150 5500 7130 12.1 16.3 25.6 36.6 48.4 62.8 74.4 94.9 107.2 125.7 166.1 259.0 200 270 420 605 800 1035 1230 1565 1770 2075 2740 4275 557.1 8915 18 ft. Lgth. * Avg. per ft. per Lgth. 12.0 16.2 25.5 36.4 48.2 62.6 74.1 94.5 106.7 124.9 165.2 215 290 460 655 870 1125 1335 1700 1920 2250 2975 20 ft. Lgth. * Avg. per ft. per Lgth. 62.3 73.6 94.0 106.0 124.2 164.2 256.0 1245 1470 1880 2120 2485 3285 5120 Class 100--100 Lb Pressure--231 Foot Head 3 .32 3.96 12.3 150 12.2 195 12.1 200 12.0 215 4 .35 4.80 16.6 200 16.4 260 16.3 270 16.2 290 6 .38 6.90 26.1 315 25.7 410 25.6 420 25.5 460 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .44 11.10 49.3 590 48.5 775 48.4 800 48.2 870 12 .48 13.20 64.0 770 62.9 1005 62.8 1035 62.6 1125 62.3 1245 14 .51 15.30 80.4 965 78.8 1260 78.6 1295 78.2 1410 77.8 1555 16 .54 17.40 97.1 1165 95.0 1520 94.9 1565 94.5 1700 94.0 1880 18 .58 19.50 117.0 1405 114.7 1835 114.4 1890 113.9 2050 113.2 2265 20 .62 21.60 138.7 1665 135.9 2175 135.7 2240 134.9 2430 134.2 2685 24 .68 25.80 182.2 2185 178.5 2855. 178.1 2940 177.2 3190 176.2 3525 30 .79 32.00 259.5 4150 259.0 4275 256.0 5120 36 .87 38.30 343.9 5500 42 .97 44.50 445.7 7130 48 1.06 50.80 557.1 8915 Class 150--150 Lb. Pressure--346 Foot Head 3 .32 3.96 12.3 150 12.2 195 12.1 200 12.0 215 4 .35 4.80 16.6 200 16.4 260 16.3 270 16.2 290 6 .38 6.90 26.1 315 25.7 410 25.6 420 25.5 460 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .44 11.10 49.3 590 48.5 775 48.4 800 48.2 870 12 .48 13.20 64.0 770 62.9 1005 62.8 1035 62.6 1125 62.3 1243 14 .51 15.30 80.4 965 78.8 1260 78.6 1295 78.2 1410 77.8 1555 16 .54 17.40 97.1 1165 95.0 1520 94.9 1565 94.5 1700 94.0 1880 18 .58 19.50 117.0 1405 114.7 1835 114.4 1890 113.9 2050 113.2 2265 20 .62 21.60 138.7 1665 135.9 2175 135.7 2240 134.9 2430 134.2 2685 24 .73 25.80 194.2 2330 190.4 3045 190.1 3135 189.2 3405 188.2 376?" 30 .85 32.00 277.3 4435 276.8 4565 273. & 5475 36 .94 38.30 42 1.05 44.50 48 1.14 50.80 368.9 479.1 595.2 5900 7665 9525 Including Bell. Calculated weight of pipe rounded off to nearest 5 pounds. References: A.S.A.--A-21.6--pipe cast in metal molds. A.S.A.--A-21.8--pipe cast in sand lined molds. A-21.11--mechanical joints. Continued on page 21 A.S.A.-- Thick Size ness ins. ins. Out side Diam. ins. 3 .32 3.96 4 .35 4.80 6 .38 6.90 8 .41 9.05 10 .44 11.10 12 .48 13.20 14 .55 15.30 16 .58 17.40 18 .63 19.50 20 .67 21.60 24 .79 25.80 30 .92 32.00 36 1.02 38.30 42 1.13 44.50 48 1.23 50.80 Weight Based On 12 ft. Lgth.* Avg. per ft. per Lgth. 16 ft. Lgth.* Avg. per ft. per Lgth. 16H ft. Lgth.* Avg. per ft. per Lgth. 18 ft. Lgth.* Avg. per ft. per Lgth. 12.3 16.6 26.1 37.2 49.3 64.0 86.0 103.5 125.9 148.7 208.4 -lass 200--200 Lb Pressure--462 Foot Head 150 200 315 445 590 770 1030 1240 1510 1785 2500 12.2 16.4 25.7 36.7 48.5 62.9 84.4 101.5 123.5 145.9 204.8 298.1 195 260 410 585 775 1005 1350 1625 1975 2335 3275 4770 12.1 16.3 25.6 36.6 48.4 62.8 84.2 101.3 123.3 145.7 204.4 297.6 200 270 420 605 800 1035 1390 1670 2035 2405 3375 4910 397.4 6360 512.3 8195 637.9 10205 12.0 16.2 25.5 36.4 48.2 62.6 83.8 100.9 122.8 144.9 203.5 215 290 460 655 870 1125 1510 1815 2210 2610 3665 Class 250--250 Lb. Pressure--577 Foot Head 3 .32 3.96 12.3 150 12.2 195 12.1 200 12.0 215 4 .35 4.80 16.6 200 16.4 260 16.3 270 16.2 290 6 .38 6.90 - 26.1 315 25.7 410 25.6 420 25.5 460 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .44 11.10 49.3 590 48.5 775 48.4 800 48.2 870 12 .52 13.20 68.8 825 67.7 1085 67.6 1115 67.4 1215 14 .59 15.30 91.6 1100 90.0 1440 89.8 1480 89.4 1610 16 .63 17.40 111.5 1340 109.6 1755 109.4 1805 108.9 1960 18 .68 19.50 134.8 1620 132.5 2120 132.2 2180 131.7 2370 20 .72 21.60 158.6 1905 155.7 2490 155.5 2565 154.8 2785 24 .79 25.80 208.4 2500 204.8 3275 204.4 3375 203.5 3665 30 .99 32.00 318.7 5100 318.2 5250 36 1.10 38.30 425.8 6815 42 1.22 44.50 549.5 8790 48 1.33 50.80 685.2 10965 20 ft. Lgth.* Avg. per ft. per Lgth. 62.3 83.4 100.3 122.2 144.2 202.6 294.6 1245 1670 2005 2445 2885 4050 5890 67.1 89.0 108.3 131.0 154.1 202.6 315.2 1340 1780 2165 2620 3080 4050 6305 Class 300--300 Lb. Pressure--693 Foot Head 3 .32 3.96 12.3 150 12.2 195 12.1 200 12.0 215 4 .35 4.80 16.6 200 16.4 260 16.3 270 16.2 290 6 .38 6.90 26.1 315 25.7 410 25.6 420 25.5 460 . 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .48 11.10 53.3 640 52.5 840 52.4 865 52.2 940 12 .52 13.20 68.8 825 67.7 1085 67.6 1115 67.4 1215 67.1 1340 14 .59 15.30 91.6 1100 90.0 1440 89.8 1480 89.4 1610 89.0 1780 16 .68 17.40 119.3 1430 117.3 1875 117.2 1935 116.7 2100 116.2 2325 18 .73 19.50 143.7 1725 141.4 2260 141.1 2330 140.6 2530 140.0 2800 20 .78 21.60 170.4 2045 167.6 2680 167.3 2760 166.6 3000 165.9 3320 24 .85 25.80 222.6 2670 219.0 3505 218.6 3605 217.7 3920 216.8 4335 Class 350--350 Lb. IPressure--808 Foot Head 3 .32 3.96 12.3 150 12.2 195 12.1 200 12.0 215 4 .35 4.80 16.6 200 16.4 260 16.3 270 16.2 290 6 .38 6.90 26.1 315 25.7 410 25.6 420 25.5 460 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .52 11.10 57.2 685 56.4 900 56.3 930 56.1 1010 12 .56 13.20 73.6 885 72.5 1160 72.4 1195 72.2 1300 71.9 1440 14 .64 15.30 98.5 1180 96.9 1550 96.7 1595 96.3 1735 95.9 1920 16 .68 17.40 119.3 1430 117.3 1875 117.2 1935 116.7 2100 116.2 2325 18 .79 19.50 154.3 1850 152.0 2430 151.7 2505 151.2 2720 150.6 3010 20 .84 21.60 182.1 2185 179.3 2870 179.0 2955 178.3 3210 177.6 3550 24 .92 25.80 239.2 2870 235.4 3765 235.1 3880 234.2 4215 233.2 4665 `Including Bell. Calculated weight of pipe rounded off to nearest 5 pounds. Note- STANDARD THICKNESSES AND WEIGHTS OF CAST IRON MECHANICAL JOINT PIPE CENTRIFUGALLY CAST IN METAL AND SAND LINED MOLDS FOR GAS Thicknesses in accordance with A.S.A. Specifications, 18,000 psi full length bursting tensile, 40,000 psi ring modulus of rupture. For pipe laid without blocks on flat bottom trench with tamped backfill under 5 feet of cover. For other conditions consult the manufacturer. Size ins. Thick ness ins. Outside Diam. ins. 12 ft. Lgth. * Avg. per ft. per Lgth. Weight Based On 16 ft. Lgth.* 16H ft. Lgth.* Avg. per ft. per Lgth. Avg. per ft. per Lgth. 18 ft. Lgth.* Avg. per ft. per Lgth. 20 ft. Lgth.* Avg. per ft. per Lgth. aass 10--10 Lb. Pressure 4 .35'" 4.80 16.6 200 16.4 260 16.3 270 16.2 290 or .38'" 4.80 17.8 215 17.6 280 17.5 290 17.4 315 6 .38'" 6.90 26.1 315 25.7 410 25.6 420 25.5 460 or .41'" 6.90 27.9 335 27.6 440 27.5 455 27.3 490 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .44 11.10 49.3 590 48.5 775 48.4 800 48.2 870 12 .48 13.20 64.0 770 62.9 1005 62.8 1035 62.6 1125 62.3 1245 16 .50 17.40 90.7 1090 88.7 1420 88.6 1460 88.1 1585 87.6 1750 20 .57 21.60 128.7 1545 125.9 2015 125.7 2075 124.9 2250 124.2 2485 24 .63 25.80 170.2 2040 166.5 2665 166.1 2740 165.2 2975 164.2 3233 30 .73 32.00 241.5 3865 241.0 3975 238.0 4760 36 .81 . 38.30 322.4 5160 42 .90 44.50 416.5 6665 48 .98 50.80 519.0 8305 Class 50--50 Lb. Pressure 4 .35'" 4.80 16.6 200 16.4 260 16.3 270 16.2 290 or .33'" 4.80 17.8 215 17.6 280 17.5 290 17.4 315 6 .33'" 6.90 26.1 315 25.7 410 25.6 420 25.5 460 or .41'" 6.90 27.9 335 27.6 440 27.5 455 27.3 490 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .44 11.10 49.3 590 48.5 775 48.4 800 48.2 870 12 .48 13.20 64.0 770 62.9 1005 62.8 1035 62.6 1125 62.3 1245 16 .50 17.40 90.7 1090 88.7 1420 88.6 1460 88.1 1585 87.6 1750 20 .57 21.60 128.7 1545 125.9 2015 125.7 2075 124.9 2250 124.2 2485 24 .63 25.80 170.2 2040 166.5 2665 166.1 2740 165.2 2975 164.2 3285 30 .79 32.00 259.5 4150 259.0 4275 256.0 5120 36 .87 38.30 343.9 5500 42 .97 44.50 445.7 7130. 48 1.06 50.80 557.1 8915 Class 100--100 Lb. Pressure 4 .35"' 4.80 16.6 200 16.4 260 16.3 270 16.2 290 or .38'" 4.80 17.8 215 17.6 280 17.5 290 17.4 315 6 .33'" 6.90 26.1 315 25.7 410 25.6 420 25.5 460 or .41'" 6.90 27.9 335 27.6 440 27.5 455 27.3 490 8 .41 9.05 37.2 445 36.7 585 36.6 605 36.4 655 10 .44 11.10 49.3 590 48.5 775 48.4 800 48.2 870 12 .48 13.20 64.0 770 62.9 1005 62.8 1035 62.6 1125 62.3 1245 16 .54 17.40 97.1 1165 95.0 1520 94.9 1565 94.5 1700 94.0 1SS0 20 .62 21.60 138.7 1665 135.9 2175 135.7 2240 134.9 2430 134.2 2685 24 .68 25.80 182.2 2185 178.5 2855 178.1 2940 177.2 3190 176.2 3525 4 .35"> 4.80 or .33'" 4.80 6 .38'" 6.90 or .41'" 6.90 8 .41 9.05 10 .44 11.10 12 .48 13.20 16.6 17.8 26.1 27.9 37.2 49.3 64.0 Class 150--150 Lb. Pressure 200 16.4 260 16.3 215 17.6 280 17.5 315 25.7 410 25.6 335 27.6 440 27.5 445 36.7 585 36.6 590 48.5 775 48.4 770 62.9 1005 62.8 270 290 420 455 605 800 1035 16.2 17.4 25.5 27.3 36.4 48.2 62.6 290 315 460 490 655 870 1125 62.3 1245 `Including Bell. Calculated weight of pipe rounded off to nearest 5 pounds. '"Class 22 thickness. '"Class 23 thickness offers increased factor of safety and is recommended for use in areas of dense population and heavy traffic. References: A.S.A.--21.7--pipe cast in metal molds- A.S.A.--A-21.9--pipe cast in sand lined molds. A.S.A.-- A-21.11--mechanical joints. STANDARD THICKNESSES AND WEIGHTS OF CAST IRON MECHANICAL JOINT PIT CAST PIPE FOR WATER AND OTHER LIQUIDS Note: Thicknesses in accordance with A.S.A. Specifications, 11,000 psi full length bursting tensile, 31,000 psi ring modulus of rupture. For pipe laid without blocks on flat bottom trench with tamped backfill under 5 feet of cover. . For other conditions consult the manufacturer. Size ins* 3 4 6 8 10 12 14 16 18 20 24 30 36 42 48 Class 50 50 lb. Pressure 115 ft. Head Class 100 100 lb. Pressure 231 ft. Head Out side Diam. ins. Weight Based on 12 ft. Length* inicK- ness Avg. per per ins. ft. Length Weight Based on _ 12 ft. Length* ness Avg. per per ins. ft. Length 3.96 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 38.30 44.50 50.80 .37 .40 .43 .46 .50 .54 .54 .58 .63 .66 .74 .87 .97 1.07 1.18 13.9 18.6 29.2 41.3 55.4 71.2 84.7 103.7 126.2 147.2 197.2 291.8 392.0 503.0 634.3 165 225 350 495 665 855 1015 1245 1515 1765 2365 3500 4705 6035 7610 .37 .40 .43 .46 .50 .54 .58 .63 .68 .71 .80 .94 1.13 1.16 1.37 13.9 18.6 29.2 41.3 55.4 71.2 90.3 111.7 135.2 157.1 211.4 312.4 448.8 540.3 724.2 165 225 350 495 665 855 1085 1340 1620 1885 2535 3750 5385 6485 8690 Class 150 150 lb. Pressure 346 ft. Head Weight Based on 12 ft. Length* ness Avg. per per ins. ft. Length .37 .40 .43 .46 .54 .58 .63 .68 .79 .83 .93 1.10 1.22 1.35 1.48 13.9 18.6 29.2 41.3 59.3 76.0 97.2 119.5 154.6 180.7 242.1 359.4 480.5 618.5 775.9 165 225 350 495 710 910 1165 1435 1855 2170 2905 4315 5765 7420 9310 Class 200 200 lb. Pressure 462 ft. Head Weight Based on 12 ft. Length* ness Avg. per per ins. ft. Length .37 .40 .43 .46 .58 .63 .68 .79 .85 .90 1.00 1.19 1.43 1.58 1.73 13.9 18.6 29.2 41.3 63.2 81.8 104.0 136.7 165.2 194.3 258.5 385.7 553.9 712.2 892.5 . 165 225 350 495 760 980 1250 1640 1980 2330 3100 4630 6645 8545 10710 Class 250 250 lb. Pressure 577 ft. Head Class 300 300 lb. Pressure 693 ft. Head Class 350 350 lb. Pressure 808 ft. Head Out side Size Diam. ins. ins. Weight Based on 12 ft. Length* Weight based on 12 ft. Length* Weight Based on 12 ft. Length* ness Avg. per per ness Avg. per per ness Avg. per per ins. ft. Length ins. ft. Length ins> ' ft. Length 3 3.96 .37 13.9 165 .37 13.9 165 .37 4 4.80 .40 18.6 225 .40 18.6 225 .40 6 6.90 .43 29.2 350 .46 30.9 370 .50 8 9.05 .50 44.5 535 .54 47.6 570 .58 10 11.10 .63 68.1 815 .68 72.9 875 .73 12 13.20 .68 87.6 1050 .73 93.4 1120 .79 14 15.30 .79 119.0 1430 .85 127.0 1525 .92 16 17.40 .85 146.0 1750 .92 156.7 1880 .99 18 19.50 .92 177.2 2125 .99 189.3 2270 1.07 20 21.60 .97 207.8 2495 1.05 223.2 2680 1.22 24 25.80 1.17 297.9 3575 1.26 318.5 3820 1.36 30 32.00 1.39 443.2 5320 1.50 474.6 5695 1.62 36 38.30 1.54 592.0 7105 1.79 677.7 8130 1.93 42 44.50 1.71 764.7 9175 48 50.80 2.02 1026.2 12315 Including Bell. Calculated weight of pipe rounded off to nearest 5 pounds. References: Thicknesses--A.S.A.--A-21.2. Mechanical joint A.S.A.--A-2I.11. 13.9 18.6 33.3 50.8 77.6 100.4 136.3 167.2 203.0 255.4 341.2 508.6 725.1 165 225 400 610 930 1205 1635 2005 2435 3065 4095 6105 8700 21B STANDARD THICKNESSES AND WEIGHTS OF CAST IRON MECHANICAL JOINT PIT CAST PIPE FOR GAS Note: Thicknesses in accordance with A.S.A. Specifications, 11,000 psi full length bursting tensile, 31,000 psi ring modulus of rupture. For pipe laid without blocks on flat bottom trench with tamped backfill under 5 feet of cover. For other conditions consult the manufacturer. Size ins. 4 6 8 10 12 16 20 24 30 36 42 48 Class 10 10 lb. Pressure Out side Diam. ins. Weight Based on __ 12 ft. Lgth.* ness Avg. per per ins. ft. Lgth. 4.80 6.90 9.05 11.10 13.20 17.40 21.60 25.80 32.00 38.30 44.50 50.80 .40 .43 .46 .50 .54 .58 .66 .74 .87 .97 1.07 1.18 18.6 29.2 41.3 55.4 71.2 103.7 147.2 197.2 291.8 392.0 503.0 634.3 225 350 495 665 855 1245 1765 2365 3500 4705 6035 7610 Class 50 50 lb. Pressure Class 100 100 lb. Pressure Class 150 150 lb. Pressure Weight Based on 12 ft. Lgth.* Weight Based on 12 ft. Lgth. * Weight Based on tu,,!2 ft- Leth-* ness Avg. per per ness Avg. per per ins. ft. Lgth. ins. ft. Lgth. .40 18.6 225 .40 18.6 225 .43 29.2 350 .43 29.2 350 .46 41.3 495 .46 41.3 495 .50 55.4 665 .50 55.4 665 .54 71.2 855 .54 71.2 855 .58 103.7 1245 .58 103.7 1245 .66 147.2 1765 .71 157.1 1885 .74 197.2 2365 .80 211.4 2535 291.8 3500 N 00 .97 1.07 392.0 503.0 4705 6035 1.18 634.3 7610 ness Avg. per per ins. ft. Lgth. .40 18.6 225 .43 29.2 350 .46 41.3 495 .50 55.4 665 .54 71.2 855 Including Bell. Calculated weight of pipe rounded off to nearest 5 pounds. References: Thicknesses--A.S.A.--A-21.3--pit cast for gas. Mechanical joint--A.S.A.--A-21.11. Bends Nominal Outside Diam. Diam. 3 3.96 4 5.00 6 7.10 8 9.30 10 11.40 12 13.50 14 15.30 16 17.40 18 19.50 20 21.60 24 25.80 30 32.00 36 38.30 42 44.50 48 50.80 T .48 .52 .55 .60 .68 .75 .66 .70 .75 .80 .89 1.03 1.15 1.28 1.42 TABLE OF DIMENSIONS 90 Bends A R Weights A 5.5 4.0 35 3.0 6.5 4.5 55 4.0 8.0 6.0 85 5.0 9.0 7.0 125 5.5 11.0 9.0 190 6.5 12.0 10.0 255 7.5 14.0 11.5 340 7.5 15.0 12.5 430 8.0 16.5 14.0 545 8.5 18.0 15.5 680 9.5 22.0 18.5 1025 11.0 36.0 32.5 2145 15.0 48.0 44.5 3575 18.0 48.0 44.5 4615 21.0 54.0 50.5 6395 24.0 45 Bends R Max. Working Weights Pressure 3.62 30 250 4.81 50 250 7.25 75 250 8.44 110 250 10.88 155 250' 13.25 215 250 12.06 270 150 13.25 340 150 14.50 420 150 16.88 530 150 18.12 755 150 27.75 1380 150 35.00 2095 150 42.25 2955 150 49.50 4080 150 All weights are approximate and do not include joint accessories. See page 19 for joint dimensions and weight of joint accessories. Three to twelve-inch fittings conform to A.S.A. Specification--A-21.10--for short body fittings. Bends Diaxn. 3 4 6 8 10 12 14 16 18 20 24 30 36 42 48 Diam* 3.96 5.00 7.10 9.30 11.40 13.50 15.30 17.40 19.50 21.60 25.80 32.00 38.30 44.50 50.80 T .48 .52 .55 .60 .68 .75 .66 .70 .75 .80 .89 1.03 1.15 1.28 1.42 TABLE OF DIMENSIONS Bends A R Weights A 3.0 7.56 30 3.0 4.0 10.06 50 4.0 5.0 15.06 .75 5.0 5.5 17.62 110 5.5 6.5 22.62 160 6.5 7.5 27.62 220 7.5 7.5 25.12 275 7.5 8.0 27.62 345 8.0 8.5 30.19 430 8.5 9.5 35.19 535 9.5 11.0 37.69 765 11.0 15.0 57.81 1400 15.0 18.0 72.88 2135 18.0 21.0 88.00 3020 21.0 24.0 103.06 4170 24.0 11^ Bends Max. R Weights Pressure 15.25 30 250 20.31 50 250 30.50 75 250 35.50 110 250 45.69 160 250 55.81 220 250 50.75 275 150 55.81 345 150 60.94 430 150 71.06 540 150 76.12 770 150 116.75 1410 150 147.25 2145 150 177.69 3035 150 208.12 4190 150 All weights are approximate and do not include joint accessories. See page 19 for joint dimensions and weight of joint accessories. Three to twelve-inch fittings conform to A.S.A. Specification--A-21.10--for short body fittings. Tees and Crosses TABLE OF DIMENSIONS Nominal Diam. Run Branch Outside Diam. Run Branch 1 Run Branch H Tee Cross Max. Working J Weight Weight Pressure 3 3 3.96 3.96 .48 .48 5.5 5.5 55 70 250 4 3 5.00 3.96 .52 .48 6.5 6.5 4 4 5.00 5.00 .52 .52 6.5 6.5 75 90 250 80 105 250 6 3 7.10 3.96 .55 .48 8.0 8.0 110 125 250 6 4 7.10 5.00 .55 .52 8.0 8.0 115 140 250 6 6 7.10 7.10 .55 .55 8.0 8.0 125 160 250 8 4 9.30 5.00 .60 .52 9.0 9.0 . 165 185 250 8 6 9.30 7.10 .60 .55 9.0 9.0 " 175 205 250 8 8 9.30 9.30 .60 .60 9.0 9.0 185 235 250 10 4 11.40 5.00 .68 .52 T1.0 11.0 235 260 250 10 6 11.40 7.10 .68 .55 11.0 11.0 250 285 250 10 8 11.40 9.30 .68 .60 11.0 11.0 260 310 250 10 10 11.64 11.64 .80 .80 11.0 11.0 310 380 250 12 4 13.50 5.00 .75 .52 12.0 12.0 315 340 250 12 6 13.50 7.10 .75 .55 12.0 12.0 325 360 250 12 8 13.50 9.30 .75 .60 12.0 12.0 340 385 250 12 10 13.74 11.64 .87 .80 12.0 12.0 390 460 250 12 12 13.74 13.74 .87 .87 12.0 12.0 410 495 250 14 6 15.30 7.10 .66 .55 14.0 14.0 435 475 150 14 8 15.30 9.30 .66 .60 14.0 14.0 450 500 ISO 14 10 15.30 11.40 .66 .68 14.0 14.0 465 540 150 14 12 15.65 13.50 .82 .75 14.0 14.0 540 630 150 14 14 15.65 15.65 .82 .82 14.0 14.0 585 710 150 16 6 17.40 7.10 .70 .55 15.0 15.0 540 575 150 16 8 17.40 9.30 .70 .60 15.0 15.0 550 605 150 16 10 17.40 11.40 .70 .68 15.0 15.0 570 645 150 16 12 17.40 13.50 .70 .75 15.0 15.0 590 685 150 16 14 17.80 15.65 .89 .82 15.0 15.0 710 830 150 16 16 17.80 17.80 .89 .89 15.0 15.0 740 895 150 All weights are approximate and do not include joint accessories. See page 19 for joint dimensions and weight of joint accessories. Three to twelve-inch fittings conform to A.S.A. Specification--A-21.10--for short body fittings. Tees and Crosses Continued TABLE OF DIMENSIONS Nominal Diam. Run Branch 18 6 18 8 18 10 18 12 18 14 18 16 18 18 20 6 20 8 20 10 20 12 20 14 20 16 20 18 20 20 24 6 24 8 24 10 24 12 24 14 24 16 24 18 24 20 24 24 30 6 30 8 30 10 30 12 30 14 30 16 30 18 30 20 30 24 30 30 36 8 36 10 36 12 36 14 36 16 36 18 36 20 36 24 36 30 36 36 42 12 42 14 42 16 42 18 42 20 42 24 42 30 42 36 42 42 48 12 48 14 48 16 48 18 48 20 48 24 48 30 48 36 48 42 48 48 Outside Diam. Run Branch 19.50 19.50 19.50 19.50 19.50 19.92 19.92 7.10 9.30 11.40 13.50 15.30 17.80 19.92 21.60 21.60 21.60 21.60 21.60 21.60 22.06 22.06 7.10 9.30 11.40 13.50 15.30 17.40 19.92 22.06 25.80 25.80 25.80 25.80 25.80 25.80 25.80 26.32 26.32 7.10 9.30 11.40 13.50 15.30 17.40 19.50 22.06 26.32 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.74 32.74 7.10 9.30 11.40 13.50 15.30 17.40 19.50 21.60 26.32 32.74 38.30 38.30 38.30 38.30 38.30 38.30 38.30 38.30 39.16 39.16 9.30 11.40 13.50 15.30 17.40 19.50 21.60 25.80 32.74 39.16 44.50 44.50 44.50 44.50 44.50 44.50 44.50 45.58 45.58 13.50 15.30 17.40 19.50 21.60 25.80 32.00 39.16 45.58 50.80 50.80 50.80 50.80 50.80 50.80 50.80 50.80 51.98 51.98 13.50 15.30 17.40 19.50 21.60 25.80 32.00 38.30 45.58 51.98 T Run Branch H .75 .55 13.0 .75 .60 13.0 .75 .68 13.0 .75 .75 13.0 .75 .66 16.5 .96 .89 16.5 .96 .96 16.5 .80 .80 .80 .80 .80 .80 1.03 1.03 .55 .60 .68 .75 .66 .70 .96 1.03 14.0 14.0 14.0 14.0 14.0 18.0 18.0 18.0 .89 .89 .89 .89 .89 .89 .89 1.16 1.16 .55 .60 .68 .75 .66 .70 .75 1.03 1.16 15.0 15.0 15.0 15.0 15.0 15.0 22.0 22.0 22.0 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.37 1.37 .55 .60 .68 .75 .66 .70 .75 .80 1.16 1.37 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 25.0 25.0 1.15 1.15 1.15 1.15 1.15 1.15 1.15 1.15 1.58 1.58 .60 .68 .75 .66 .70 .75 .80 .89 1.37 1.58 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 28.0 28.0 1.28 1.28 1.28 1.28 1.28 1.28 1.28 1.78 1.78 .75 .66 .70 .75 .80 .89 1.03 1.58 1.78 23.0 23.0 23.0 23.0 23.0 23.0 31.0 31.0 31.0 1.42 1.42 1.42 1.42 1.42 1.42 1.42 1.42 1.96 1.96 .75 .66 .70 .75 .80 .89 1.03 1.15 1.78 1.96 26.0 26.0 26.0 26.0 26.0 26.0 26.0 34.0 34.0 34.0 All weights are approximate and do not include joint accessories. See page 19 for joint dimensions and weight of joint accessories. J 15.5 15.5 15.5 15.5 16.5 16.5 16.5 17.0 17.0 17.0 17.0 17.0 18.0 18.0 18.0 19.0 19.0 19.0 19.0 19.0 19.0 22.0 22.0 22.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 25.0 25.0 26.0 26.0 26.0 26.0 26.0 26.0 26.0 26.0 28.0 28.0 30.0 30.0 30.0 30.0 30.0 30.0 31.0 31.0 31.0 34.0 34.0 34.0 34.0 34.0 34.0 34.0 34.0 34.0 34.0 Tee Weight 590 605 620 640 755 905 945 725 735 755 775 795 945 1140 1185 985 1000 1020 1030 1055 1075 1400 1720 1815 1730 1745 1760 1780 1800 1820 1845 1875 2880 3105 2520 2535 2550 2570 2585 2610 2635 2690 4345 4590 3555 3575 3595 3615 3640 3690 4650 6075 6320 4870 4885 4905 4925 4950 4995 5140 6280 8130 8420 Cross Max. Weight Pressure 625 655 685 725 870 1060 1130 150 150 150 150 150 150 150 760 790 820 860 905 1085 1330 1415 150 150 150 150 150 150 150 150 1025 1045 1085 1110 1155 1200 1590 1965 2155 150 150 150 150 150 150 150 150 150 1770 1795 1830 1865 1905 1950 2000 2060 3180 3640 150 150 ISO 150 150 150 150 150 150 150 2565 2600 2630 2665 2705 2750 2805 2910 4790 5280 ISO 150 150 150 150 150 150 150 150 150 3640 3675 3715 3755 3810 3910 5040 6655 7145 150 150 150 150 150 150 150 150 150 4955 4985 5025 5065 5115 5210 5495 6790 8815 9380 150 150 150 150 150 150 150 150 150 150 26 Reducers Nominal Diam. D D' 43 63 64 84 86 10 4 10 6 10 8 12 4 12 6 12 8 12 10 14 6 14 8 14 10 14 12 16 6 16 8 16 10 16 12 16 14 18 8 18 10 18 12 18 14 18 16 20 10 20 12 20 14 20 16 20 18 24 12 24 14 24 16 24 18 24 20 30 18 30 20 30 24 36 20 36 24 36 30 42 20 42 24 42 30 42 36 48 30 48 36 48 42 Outside Diam* Large Small 5.00 7.10 7.10 9.30 9.30 11.40 11.40 11.40 13.50 13.50 13.50 13.50 15.30 15.30 15.30 15.30 17.40 17.40 17.40 17.40 17.40 19.50 19.50 19.50 19.50 19.50 21.60 21.60 21.60 21.60 21.60 25.80 25.80 25.80 25.80 25.80 32.00 32.00 32.00 38.30 38.30 38.30 44.50 44.50 44.50 44.50 50.80 50.80 50.80 3.96 3.96 5.00 5.00 7.10 5.00 7.10 9.30 5.00 7.10 9.30 11.40 7.10 9.30 11.40 13.50 7.10 9.30 11.40 13.50 15.30 9.30 11.40 13.50 15.30 17.40 11.40 13.50 15.30 17.40 19.50 13.50 15.30 17.40 19.50 21.60 19.50 21.60 25.80 21.60 25.80 32.00 21.60 25.80 32.00 38.30 32.00 38.30 44.50 TABLE OF DIMENSIONS Metal Thickness Bell & Bell Large End Bell Small Ind Bell Max. T .52 .55 .55 .60 .60 .68 .68 .68 .75 .75 .75 .75 .66 *66 .66 .66 .70 .70 .70 .70 .70 .75 .75 .75 .75 .75 .80 .80 .80 .80 .80 .89 .89 .89 .89 .89 1.03 1.03 1.03 1.15 1.15 1.15 1.28 1.28 1.28 1.28 1.42 1.42 1.42 T' .48 .48 .52 .52 .55 .52 .55 .60 .52 .55 .60 .68 .55 .60 .68 .75 .55 .60 .68 .75 .66 .60 .68 .75 .66 .70 .68 .75 .66 .70 .75 .75 .66 .70 .75 .80 .75 .80 .89 .80 .89 1.03 .80 .89 1.03 1.15 1.03 1.15 1.28 L Weight 7 40 9 55 9 60 11 80 11 95 12 105 12 115 12 135 14 135 14 150 14 165 14 190 16 190 16 210 16 230 16 255 18 230 18 250 18 280 18 305 18 335 19 295 19 325 19 350 19 380 19 415 20 375 20 405 20 430 20 470 20 510 24 550 24 575 24 615 24 660 24 705 30 990 30 1050 30 1165 36 1450 36 1580 36 1855 42 1915 42 2060 42 2370 42 2695 48 3005 48 3370 48 3750 L Weight 15 40 17 55 17 60 19 80 19 90 20 100 20 115 20 130 22 130 22 145 22 165 22 185 24 185 24 205 24 230 24 255 26 230 26 250 26 275 26 305 26 315 27 295 27 320 27 350 27 365 27 395 28 375 28 405 28 415 28 445 28 485 32 550 32 560 32 595 32 635 32 675 38 965 38 1020 38 1125 44 1420 44 1535 44 1750 50 1880 50 2020 50 2265 50 2530 56 2900 56 3205 56 3540 L Weight Pressure 15 35 250 17 50 250 17 60 250 19 80 250 19 90 250 20 100 250 20 115 250 20 130 250 22 130 250 22 150 250 22 165 250 22 190 250 24 175 150 24 190 150 24 215 150 24 240 150 26 210 150 26 230 150 26 255 150 26 285 T50 26 310 150 27 270 150 27 300 . 150 27 325 150 27 355. 150 27 390 150 28 345 150 28 375 150 28 400 150 28 435 150 28 475 150 32 510 150 32 535 150 32 575 150 32 620 150 32 665 150 38 885 38 945 38 1060 150 150 150 44 1285 44 1410 44 1690 150 150 150 50 1705 50 1855 50 2165 50 2485 150 150 150 150 56 2740 56 3100 56 3480 150 150 150 All weights are approximate and do not include joint accessories. See page 19 for joint dimensions and weight of joint accessories. Three to twelve-inch fittings conform to A.S.A. Specification--A-21.10--for short body fittings. SOLID SLEEVE -- -Sc________________ 1_4i_ ----rt-i-------i t --------------------x--------------SPLIT SLEEVE* TRANSITION SLEEVE** Sleeves Nominal Diam. 3 4 6 8 10 12 14 16 18 20 24 . 30 36 42 48 T .48 .52 .55 .60 .68 .75 .82 .89 .96 1.03 1.16 1.37 1.58 1.78 1.96 Fits O. D. C. I. Pipe 3.96 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 38.30 44.50 50.80 L. 7.5 7.5 7.5 7.5 7.5 7.5 9.5 9.5 9.5 9.5 9.5 15.0 15.0 15.0 15.0 TABLE OF DIMENSIONS Solid Sleeves Split Sleeves Transition Sleeves Fits O. D. X Steel Weight Li Weight Min. Pipe Max. Working Y Weight Pressure 25 12 30 10 3.50 7.50 25 250 35 12 45 10 4.50 7.50 35 250 45 12 65 10 6.62 7.50 45 250 65 12 85 10 8.62 7.50 65 250 85 12 ' 115 10 10.75 7.50 85 250 110 12 145 10 12.75 7.50 110 250 165 15 225 11 150 200 15 275 11 150 240 15 330 11 150 275 15 380 11 150 360 15 505 11 150 745 24 1085 15 150 1030 24 1495 15 150 1330 24 1940 15 150 1645 24 2405 15 150 *This split sleeve can be furnished with boss and tap for service connection. "Transition sleeves are furnished with one end designed for standard steel outside diameter pipe and the other to fit mechanical joint cast iron pipe. All weights are approximate and do not include joint accessories. See page 19 for joint dimensions and weight of joint accessories. GLAND Glands, Plugs and Caps TABLE OF DIMENSIONS Weights Weights Nominal Solid Split Diam. Glands Glands Design T Plugs Caps 3 5 9 Flat .75 14 13 4 6 14 Hat .75 20 20 6 11 18 Flat .75 30 30 8 18 20 Flat .75 50 45 10 20 30 Hat .75 65 55 12 30 35 Flat .75 85 75 14 35 60 Dished .82 115 120 16 45 70 Dished .89 150 155 18 55 85 Dished .96 195 190 20 70 100 Dished 1.03 225 240 24 90 130 Dished 1.16 330 345 30 180 205 Dished & Ribbed 1.37 590 660 36 235 265 Dished & Ribbed 1.58 880 960 42 300 330 Dished & Ribbed 1.78 1250 1355 48 365 400 Dished & Ribbed 1.96 1670 1830 Max. Working Pressure 250 250 250 250 250 250 150 150 150 150 150 ISO 150 150 150 All weights are approximate. See page 19 for joint dimensions and weight of joint accessories. -16- pa Figure B Figure C -5- Figure D All flanges are American 125 standard unless otherwise specified. Connecting Pieces Diam 3 4 6 8 10 12 14 16 18 20 24 30 36 42 48 Body O.D. 3.96 5.00 7.10 9.30 11.40 13.50 15.30 17.40 19.50 21.60 25.80 32.00 38.30 44.50 50.80 .48 .52 .55 .60 .68 .75 .66 .70 .75 .80 .89 1.03 1.15 1.28 1.42 J.E. "G" 3.% 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 38.30 44.50 50.80 TABLE OF DIMENSIONS A B C D E* MJ&Flg Fig. & PE MJ&PE MJ&B MJ&MJ Max. Tt Weight Weight Weight Weight Weight Pressure .48 30 30 35 40 35 250 .45 40 40 45 55 45 250 .48 60 55 65 80 70 250 .51 85 85 95 115 95 250 .57 115 115 125 150 130 ' 250 .62 155 155 165 190 165 250 .66 195 180 205 230 220 150 .70 240 220 250 290 270 150 .75 280 255 300 340 325 150 .80 340 305 360 405 390 150 .89 455 415 475 530 515 150 1.03 710 600 730 820 840 150 1.15 1000 830 1005 1170 1170 150 1.28 1325 1115 1295 1515 1500 150 1.42 1655 1390 1640 1930 1910 150 Fittings shown in Fig. B and C may be furnished from centrifugally cast pipe. Figure E is a mechanical joint-to-mechanical joint connecting piece having laying length of 8*. All weights are approximate. See page 19 for joint dimensions and weight of joint accessories. Offsets TABLE OF DIMENSIONS Plain Outside Max. Nominal End Diam. Working Diam. Diam. ' A Drop L T. T* Weight Pressure 3 3.96 3.96 6 27 .48 .48 50 250 3 3.96 3.96 12 30 .48 .48 60 250 3 3.96 3.96 18 38 .48 .48 75 250 4 4.80 5.00 6 27 .52 .45 70 250 4 4.80 5.00 12 30 .52 .45 80 250 4 4.80 5.00 18 38 .52 .45 100 250 6 6.90 7.10 6 28 .55 .48 105 250 6 6.90 7.10 12 34 .55 .48 130 250 6 6.90 7.10 18 41 .55 .48 160 250 8 9.05 9.30 6 29 .60 .51 155 250 8 9.05 9.30 12 36 .60 .51 195 250 8 9.05 9.30 18 43 .60 .51 240 250 10 11.10 11.40 6 30 .68 .57 220 250 10 11.10 11.40 12 38 .68 .57 280 250 10 11.10 11.40 18 46 .68 .57 340 250 12 13.20 13.50 6 34 .75 .62 320 250 12 13.20 13.50 12 45 .75 .62 420 250 12 13.20 13.50 18 56 .75 .62 520 250 All weights are approximate. See page 19 for joint dimensions and weight of joint accessories. 3"-24.h PRP POTS Drip Pots DIMENSIONS IN INCHES Size A. A 4 5.00 15.30 B. B 3.96 13.98 C 6.00 E 10.75 H 14.75 26.75 Ti .52 Plug. Cap., Wts., T Size qts. lbs. 32 435 .66 14 64 530 15.75 6 7.10 15.30 6.00 13.98 7.12 10.75 27.75 .55 28.75 8 9.30 15.30 8.10 13.98 8.25 10.75 40.88 .60 10 11.40 15.30 10.04 13.98 9.25 10.75 29.75 41.88 .68 30.88 12 13.50 17.40 12.00 16.00 10.25 11.75 42.88 .75 34.12 16 17.40 21.60 16.00 20.00 12.25 14.38 46.88 .70 32 465 .66 14 64 560 64 595 .66 14 96 695 64 645 .66 14 96 740 84 .70 16 126 815 930 138 1285 .80 20 208 1460 36.75 20 21.60 25.80 20.00 24.02 15.38 16.50 49.62 .80 203 1875 .89 24 304 2110 36.12 280 2895 24 25.80 32.00 24.02 29.94 17.50 20.50 47.62 .89 1.03 30 420 3195 Weights include plug, bolts and gasket for top. All weights are approximate. See page 19 for joint dimensions and weight of joint accessories. 31 Gaskets, Glands and Bolts jfor mechanical joint cast iron pipe and fittings (in conformance with A.S.A.--A-21.11) All gaskets furnished for the standardized mechanical joint are produced by long-established manufacturers who are recognized specialists in this field, and are made to accurate dimensions under rigid controls and inspection. Generally plain rubber gaskets are furnished and in sufficient quantities to provide for each socket opening on pipe and fittings. Metal tipped, duck tipped, Thiokol tipped and other special types of gaskets can be supplied when specified by the purchaser. Glands are made of special high quality cast iron under rigid metallurgical controls and inspections. Bolts furnished with the standardized mechanical joint are made ofhigh strength cast iron and have a minimum tensile strength of 50,000 pounds per square inch. They possess the,inherent corrosion resistance of cast iron and will therefore play their full part in living up to the long life records of the pipe itself. Other types of bolts for unusual requirements are furnished to meet purchasers' specifications. Glands and bolts are furnished in sufficient quantities to provide for each socket opening on pipe and fittings.' Thus, the standardized mechanical joint is homogeneous throughout--a true cast iron joint.