Document ExNq2mkdr5XEZxZG3onq00v0V

To From Subject cc: Mr. W. C. Strader ETHYL CORPORATION Mr. H. 0. Bourque Mr. J. E. Gonce Mr. J. C. Klock S. A. D'Armond INTER-OFFICE Address Address Date 8/16/73 Listed below are certain OSHA training and record keeping requirements. (1) Training CRF PART FEDERAL REGISTER STANDARD "QUOTE" 1910.134 Respiratory protection p. 22231 ' (3) The employee shall use the provided respiratory protection in accordance with instructions and training received. (b) Requirements for a minimal acceptable program. (1) Written standard operating procedures governing the selec tion and use of respirators shall be established. (2) Respirators shall be selected on the basis of hazards to which the worker is exposed. (3) The user shall be instructed and trained in the proper use of respirators and their limitations. p. 22232 (2) The correct respirator shall be specified for each job. The respirator type is usually specified in the work procedures by a qualified individual supervising the respiratory protective program. The individual issuing them shall be adequately instructed to Insure that the correct respirator is issued. (3) Written procedures shall be prepared covering safe use of respirators in dangerous atmospheres that might be encountered in normal operations or in emergencies. Personnel shall be familiar with these procedures and the available respirators. (1) Taken from U.S. Dept, of Labor bulletin - OSHA 2082 & titled "Training Requirements of the Occupational Safety-and Health Standards". VC1167 2. CRF PART FEDERAL REGISTER STANDARD "QUOTE" * The Baton Rouge Plant Safety Office does not think it is necessary for safety purposes to wear in test atmosphere at the Baton Rouge Plant at this time. ^910.178 Powered industrial trucks. p.22257 (5) For safe use of any respirator, it is essential that the user be properly in structed in its selection, use, and main tenance. Both supervisors and workers shall be so instructed by competent persons. Training shall provide the men an oppor tunity to handle the respirator, have it fitted properly, test its face-piece-to-face seal, wear it in normal air for a long familiarity period, and finally,* to wear it in a test atmosphere. (i) Every respirator wearer shall receive fitting instructions including demonstra tions and practice in how to adjust it, and how to determine if it fits properly. To assure proper protection, the facepiece fit shall be checked by the wearer each time he puts on the respirator. This may be done by following the manufacturer's facepiece fitting instructions. (1) Operator training. Only trained and authorized operators shall be per mitted to operate a powered industrial truck. Methods shall be devised to train operators in the safe operati n of powered industrial trucks. 1910.217 Mechanical power presses. p. 22288 (3) Training of maintenance personnel. It shall be the responsibility of the em ployer to insure the original and contin uing competence of personnel caring for, inspecting, and maintaining power presses. (2).Instruction to operators. The employer shall train and instruct the operator in the safe method of work before starting work on any operation covered by this section. The employer shall Insure by adequate supervision that correct operating procedures are being followed. VC1168 3. CRF PART FEDERAL REGISTER STANDARD "QUOTE" 1910.252 Welding, cutting, and brazing. p. 22305 p. 22306 p. 22307 /1910.264 p. Laundry /machinery and operations 22331 (iii) Instruction. Workmen designated to operate arc welding equipment shall have been properly instructed and qualified to operate such equipment a^ specified in subparagraph (4) of this paragraph. (iii) Personnel. Workmen designated to operate resistance welding equipment shall have been properly instructed and judged competent to operate such equipment. (6) Maintenance. Periodic inspection shall be made by qualified maintenance personnel, and records of the same main tained. The operator shall be Instructed to report any equipment defects to his supervisor and the use of equipment shall be discontinued until safety repairs have been completed. (v) Instruction of employees. Employees shall be properly instructed as to the hazards of their work and be instructed in safe practices, by bulletins, printed rules, and verbal Instructions. (2) RECORD KEEPING A brief explanation is given here - you will find full explanation in the reference standard numbers. SUBPART I SECTION Respiratory protection PARAGRAPH EXPLANATION 1910.134 (e)(2) 1910.134 <f)(3)(iv) Recording issue date for respirators Record of inspection dates and findings for respirators maintained for emergencies (2) Taken from "Table of Specialized Records," published in National Safety News, March 1973. VC1169 *f 4. SUBPART SECTION PARAGRAPH EXPLANATION I Portable fire 1910.157 Tag on fire extinguisher to extinguishers (d)(3)(iv) show date of maintenance or recharge and identification of person performing this service 1910.157 Hydrostatic test date of <d)(4)(viii) fire extinguishers Fixed dry . chemical extinguishing systems 1910.160 (c)(1)(iii) Report and recommendations of the inspector N Overhead and 1910.179 Report of monthly rope gantry cranes (m) (1) inspections and (2) Crawler, loco motive, and truck cranes 1910.180 (d)(6) Record of monthly inspec tion of criticial items (brakes, crane hooks, ropes) Derricks 1910.180 (g)(1) and 1910.180 (g)(2)(ii) 1910.181 (g)(1) and (3) Monthly rope inspection records Monthly rope inspection records 0 Mechanical 1910.217 Inspection and maintenance power press (e)(1) records Forging machines 1910.218 (a)(2)(i) and (ii) Records of safety inspections Q Welding, 1910.252 Records of periodic inspection cutting and (c)(6) of resistance welding equipment brazing VC1170 5. With the assumption that you will comply with the requirements as they pertain to your organization, will you please advise me of action taken to comply and to keep in compliance. SAD:sgm S. A. D'Armond \ / / VC1171