Document Ed98dJdN107b04MwpJ0VbvnZj

21S.879 215.881 215.883 215.886 Compliance Date Compliance Plan Special Requirements for Compliance Plan Testing.and Monitoring . amended-in R86-10 at. 12 111: Reg. 7650. effective April II. 1988; amended In R87-1 at 12 . m. Reg. 20133 effective Rovember 21. 1988. ROTE: Capitalization denotes statutory language. Subpart PP: MISCELLANEOUS FABRICATED PROOUCT MANUFACTURING PROCESSES SUBPART A: GENERAL PROVISIONS Section 215.920 215.923 - 215.926 Applicability Permit Conditions Control. Requirements Subpart QQ: MISCELLANEOUS FORMULATION MANUFACTURING PROCESSES Section 215.940 215.943 215.946 Applicability . Permit Conditions Control Requirements lection 215.100 introduction # a) This Part .'Contains standards and limitations ' for emissions of organic material from staLionary.saurces. b). Sources subject to this Part may be subject to-the following: 1) Permitsrequlredunder 35 ITT. Adh. Code' 201; Subpart RR: MISCELLANEOUS ORGANIC CHEMICAL MANUFACTURING PROCESSES 21 Air quaVltystandardiunder 35 111. Adm. Code 243. .Section . 215.960 215.963 215.966 Applicability Permit Conditions Control Requirements c) This Part. Is.divided Into .Subparts which are grouped as follows: 1Y Subpart A: GeneraV provVs-tons; ..... Appendix A: Appendix B: Appendix C: Appendlx O: i. Appendix E: . Appendix F: Rule Into Section Table Section Into Rule Table. Past'Compliance Oates. list of Chemicals Oeftnlng Synthetic Organic Chemical and Polymer Manufacturing' Reference Methods and Procedures Coefficients for the Total Resource Effectiveness Index (TRE) Equation 2) Subparts B - J: Emissions from equipment and operations. In cannon to more than one industry:, 1 31. Subpaz.Ls.X-- 1U. Emissions from use of. ... organic material; ..- 4) Subparts N - end: Special rules for various industry groups. AUTHORITY: Implementing Section 10 and authorized-by Section 27 of the Environmental Protection Act (111. Rev. Stat. 1987. ch. Ill 1/2. pars. 1010 and 1027). .SOURCE: Adopted as.Chapter 2: Air Pollution. Rule 205; Organic Material Emission Standards and Limitations. R71-23. 4 PCB 191. filed and effective April 14. 1972; amended 1n.R77-3. 33 PCB 3S7. at 3 111. Reg. 18. p. 41; effective May 3. 1979; amended In R78-3 and R78-4. 35 PC8 75. ,:at 3 ill. .Reg. 30. p. 124.. effective July 28. 1979; amended In R80-5 at 7 111. Reg. 1244. effective January 21. 1983; codified at 7 111. Reg.-.13601 Notice of Correction's at 7111. Reg. ..14575: amended In R82-14 at 8 111. Reg. 13254. effective July 12. 1984; amended In R83-36 at 9 111. Reg. 9114. effective May 30. .1985; amended In R82-14 at 9 111. Reg. 13960, effective August .28. 1985; amended In R8S-28 at 11 Til: Reg. 3127. effectlve.-February 3. 1987; amended In R82r.14 at II HI. Reg. 7296. effective April 3. 1987; amended In R8S~21(A) at IT ill. Reg. 11770,.effective June 29, 1987; recodified In R86-39 at 11 111. Reg. 13S41; amended in R82-I4 and R86-12 at 11 111. Reg. 16706. effective September 30. 1987; amended In R8S-2K8) at 11 111. Reg. 19117, effective Hoven*er~9. 1987; amended in R86-36. R86-39. R86-40 at 11 111. Reg. 20829; effective December 14. 1987; amended In R82-14 and R86-37 at 12 111. Reg. 81S. effective Oecember 24. 1987; amended in R86-18 at 12 111. Reg. 7311. effective April 8. 1988; (Source: Added and codified'at"7 111. Reg. 13601)., Section 21$.101 Clean-up and Disposal Operations Eatss.1 otrof organic.,material released during clean-up operations and disposal shall be Included with other emissions of organic material from the related emission source or air pollution control"equipment; tn determtniogtotaV emissions. (Source: Amended at 3 111. Reg. 124. effective July 28. 1979) Section 215.102 Testing Methods a) The total - organic- materia* concentrations. In... an effluent stream shall be measured by a flame Ionization detector, or by other methods, approved by the. Illinois Env IraomenlaL ecotecLloft-Agency. (Agency).... according to the provisions of 35 111. Adm. Code 201. b) Measurement of Vapor Pressures. 1) For a single-component, the actual vapor pressure shall be determined by ASTM (American Society of Testing and - 89 -