Document DDd9d0r32ZQe2QZ4g2GbjkVJN

Shaw-Perkins Manufacturing Company 201 East Carson St., Pittsburgh 19, Pa. Manufacturers of SHAW Panel-Vectors delivering AIR-e-ATED Radiant Heat SKIDMORE CORPORATION ST. JOSEPH, MICHIGAN Quality Heating Pumps Since 1921 All Shaw Panel-Vectors and Perkins AIRadiators are complete one-piece factory assembled units ready for installation. Manufactured of heavy gage steel with fulllength heating fins and vertical serpentine copper heating coils, pressure fitted for excellent heat transfer. Numerous. sizes and models available to meet any area heat loss. Institutional models possess perforated paneling for low surface temperatures. Perkins AIRadiators are designed for industrial installations, and are readily mounted ou either ceilings or walls. SHAW Panel-Vectors (front or top air outlets) DEPTH, front to back--3 in. HEIGHTS--8 in., 11 in., 14 in., 17 in., 20 in., 23 in., 26 in. LENGTH--11 in. to 111 in. inclusive, in 2 in. increments. TAPPING--supply and return same end, right or left hand; also furnished on opposite ends. PIPING--connections for y2 in., % in., or 1 in, piping. RATINGS--3.9 EDR to 117.7 EDR, based on 1 ib steam and 65 F inlet air. INSTALLATION--wall hung, free standing, open or closed recess. APPLICATION--hot water, steam to 150 psi. End panels, air chambers, wall brackets available for any application. SHAW BASEBOARD Panel-Vectors DEPTH, front to back--3 in. HEIGHT--8 in. LENGTHS--2 ft 5 in. to 72 ft 7 in. inclusive, in 2 in. increments. TAPPING--supply and return same end, right or left hand; also furnished on opposite ends. PIPING--connec tions for % in. piping on same end, 1 in. piping on opposite ends. RATINGS __6.7 EDR per linear ft based on 1 lb steam and 65 F inlet air. INSTAL LATION--wall hung with inside and outside corner runs. APPLICATION __hot water, steam to 150 psi. End panels, air chambers, and mounting screws included as standard equipment Write (or bulletin No. KHZ on type VCS Pump SKIDMORE TYPE VCS PUMP i The Skidmore Type VCS vertical close-coupled pump with V mechanical shaft-seal is specially designed for hot water y service. Heavy duty type and bronze fitted construction, | pump is bolted directly to a cast iron receiver. Furnished in either single or duplex units. The extended motor shaft g is stainless steel and since it is not subject to wear or | scoring, no shaft sleeve is required. The entire pump and | motor unit may be removed for inspection or repair with| out disturbing any pipe connection. Capacities 1,000 to 1100,000 sq. ft EDR. Discharge pressure 10 to 75 lb. Write for Bulletin No. 21-C on type CCVS Pump SKIDMORE TYPE CCVS PUMP The Skidmore Type CCVS Condensate Pump is new dosecoupled design. Built to give maximum efficiency, yet requires a minimum of space. Shown above is the duplex pump with two float switches. This model is also furnished with automatic alternator. The CCVS Pump is also built in single unit. Motor and pump are bolted to receiver. Pump is bronze fitted throughout with enclosed centrifugal impeller of special design for hot water. Capacities 500 to 10,000 sq ft EDR and pressures from 10 to 40 lb: SHAW INSTITUTIONAL Panel-Vectors DEPTH, front to back--3 in. HEIGHTS--8 in., 11 in., 14 in., 17 in., 20 in., 23 in., 26 in. LENGTHS--11 in. to 111 in. inclusive, in 2 in. increments. Steel housing has % in. diam. perforations on in. staggered centers. TAPPING--supply and return same end, right or left hand; also furnished on opposite ends. PIPING--connections for % in., % in., or 1 in. piping- RATINGS--5.0 EDR to 100.9 EDR based on 1 ib steam and 65 F inlet air. INSTALLATION--flush mounting for violent areas, offset mounting for non-violent areas. APPLICATION--hot water, high temperature hot water, steam to 150 psi. End panels for complete pipe covering. PERKINS AIRadiator DEPTH, front to back--5 in. HEIGHTS--14% in., 23% in., 32% in. LENGTHS--15 in. to 125 in. inclusive, in 2% in. increments. -TAPPING --supply and return on opposite ends; top and bottom arrangement reversi ble by reversing radiators. PIPING--connections for 1 in. piping; may be bushed to % in. or % in. as specified. RATINGS--14 EDR to 187 EDR based on 1 lb steam and 65 F inlet air. INSTALLATION--ceding or wail hung. APPLICATION--hot water, steam to 150 psi. Ceiling hangers or wall brackets available for mounting. Represented in principal cities. Send for catalog. TYPE HS PUMP Write for Bulletin No. I4-B The model HS Condensation pump is eco nomically designed to offer maximum effi ciency with lower operating cost. The Type HS will operate at high temperature 'en countered in condensation pomp service. The pump can be disassembled without dis turbing piping connections. Famished ` in either single or daplex type. Pump casing [s constructed of heavy close grain cast iron, vertically split, bronze fitted throughoat. Capacities 1,000 to 125,000 sq ft EDR, pressures 10 to 75 lb. Write for Bulletin No. 9-C VACUUM PUMP Built in both single and duplex units. The Skidmore Vacuum Pump is designed for re turn liae vacuum heating systems. Pump automatically adjusts itself to the varying conditions of the system. Liberal clearance between moving parts means Maintained Efficiency. Capacities ranging from 5,000 to 100,000 sq ft EDR. Write for Bul letin No. 19-B on Type UV' Pump TYPE UV PUMP The Skidmore Type VV Pump is designed for use where returns are too low to permit the operation of horizontal pumps. Operates very satisfactory where condensate is to be returned to the boiler or other points, from steam heating systems or process equipment Consists of vertical pump and motor uuit with float and float switch mechanism mounted on cover plate which is bolted to sump type receiver. Capacities 2000 to 40,000 sq ft EDR, pressures from 10 to 75 lb. Skidmore Pomps are built in single and duplex units Write for complete engineering data on all Skidmore Pumps h It it :tv 13 It Hi P