Document DDa7rNE64vvQ2kpQY0GLxQqkQ

Heating Ventilating Air Conditioning Guide 1939 for a total leader pipe area up to 790 sq in. Above 790 and up to 1,000 sq in. of leader^ pipe area the lining should be at least 11J4 x 11)4 In. inside. In case of brick flueg JjJjj less than 35 ft in height with no linings, the internal dimensions should be at 1qJ?| 8 x 12 in. up to 790 sq in. of leader area, and at least 12 x 12 in. for leader capacities 1,000 sq in. Chimneys under 35 ft in height are unsatisfactory in operation and hew should be avoided. CHIMNEYS FOR GAS HEATING | The burning of gas differs from the burning of coal in that the force! which supplies the air for combustion of the gas comes largely from the! pressure of the gas in the supply pipe, whereas air is supplied to a bed off burning coal by the force of the chimney draft. If, with a coal-burning! boiler, the draft is poor, or if the chimney is stopped, the fire is smothered! and the combustion rate reduced. In a gas boiler or furnace such al condition would interfere with the combustion of the gas, but the ga/ would continue to pass to the burners and the resulting incomplete com-l bustion would produce a dangerous condition. In order to prevent incon/ plete combustion from insufficient draft, all gas-fired boilers and furnaces should have a back-draft diverter in the flue connection to the chimnnery.-S- Table 2. Suggested General Dimensions for Vertical Back-Draft Diverter Chapter 10. Chimneys and Draft Calculations < A study of a typical back-draft diverter shows that partial or complete hVnnev stoppage will merely cause some of the products of combustion r"r, Vented out into the boiler room, but will not interfere with com bustion. In fact, gas-designed appliances must perform safely under such condition to be approved by the American Gas Association Laboratory. Other functions of the back-draft diverter are to protect the burner and nilot from the effects of down-drafts, and to neutralize the effects of variable chimney drafts, thus maintaining the appliance efficiency at a substantially constant value. Converted boilers or furnaces, as well as gas-designed appliances, should be provided with back-draft diverters. " Since back-draft diverters have a special function to perform in pro tecting gas burning appliances, it is necessary that they should be built to the proper size as shown in Table 2 for a vertical type and in Table 3 for a horizontal arrangement. Equipment of this kind listed by the American Gas Association Testing Laboratory must bear the listing symbol A .G.A. Table 3. Suggested General Dimensions for Horizontal Back-Draft Diverter -- C-------------------- 1 1 ` F--ill . t /-Baffle I- // , lA M'Inlet -- E i B I Pipe . ' Size A B .3 4 .5 6 7. 8 9 10 'll 12 33 44 55 66 7' 7 8. 8 99 10 10 11 11 12 12 Table of Dimensions (In.) c 5.5 7.2 9.4 11.5 13.5 15.5 17.5 19.7 22.2 24.7 D E 7.0 3.8 9.5 5.0 10.8 5.3 12.0 5.6 13.9 6.4 15.8 7.1 17.5 7.7 18.8 7.9 20.7 8.4 22:2 . 8.7 F 0.7 1.0 .1.5 1.9 2.3 2.7 3.1 3.6 4.3 5.0 .G 4.4 6.0 8.0 9.8 11.6 13.4 15.2 17.2 19.6 22.0 H 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 1 I J K L M| I1.5 2.5 0.7 1.5 2.3 2.0 3.5 1.0 2.0 3.0 | 2.3 4.0 0.9 2.4 3.51 2.5 4.5 0.8 2.7 4.01 6i2.9 5.3 0.9 3.1 413.2 6.0 1.0 3.5 5- i3.5 6.7 1.0 4.0 5- I 3.8 7.3 1.0 4.3 6.2 4.1 8.0 1.5 4.6 6.6 4.4 8.5 1.7 5.0 7.0 3 IS Table of Dimensions (In.) Pipe She A B C D E FG H I J K L M' 3 4 5 6 ,,9 3 3 6 1.5 4.8 3.8 1.4 4 4 8 2.0 4.8 5.0 1.9 5 5 10 2.5 4.8 6.3 2.4 6 6 12 3.0 4.8 7.5 2.9 7 7 14 3.5 4.8 8.8 3.4 8 8 16 4.0 4.8 10.0 3.9 9 9 18 4.5 4.8 11.3 4.4 10 10 20 5.0 4.8 12.5 4.9 11 11 . 22 5.5 4.8' 13.8 5.4 12 12 24 6.0 4.8 15.0 5.9 2.5 3.4 4:2 5.0 5.9 6.7 7.5 8.4 9.2 10.0 2.5 3.4 4.2 5.0 5.9 6.7 7.5 8.4 9.2 10.0 2.5 2.1 0.6. 1.8 3.4 2.9 0.8 2.3 4.2 3.5 09 2.9 5.0 4.3 1.1 3.5 5.9 5.0 1.3 4.1 6.7 5.6 1.5 4.7 7.5 6.4 1.7 5.3 8.4 7.0 1.9 5.8 9.2 7.8 2.1 6.4 10:0 8.5 2.3 7.0 202 ft] 203