Document BEad75Do50RjVkyBqgMg2EX8

Document no: Issue number Page 1 of 4 RTS/ENG/140192 1 Marine Design Appraisal Document Lloyd's Register EMEA Rotterdam Technical Support Office K.P. van der Mandelelaan 41a, 3062 MB Rotterdam P.O. Box 701, 3000 AS Rotterdam Tel: 50 88, Fax 84 E: @Ir.org W: http://www.lr.org Date 18 December 2019 Please quote this reference number on all future communications RTS/ENG/195207/GKV/VSZ Machinery General Design Appraisal Client : AEGIR-Marine B.V. Manufacturer : AEGIR-Marine Production B.V. Subject : Stern Tube Seals G.A. Registration No. : ROT.14.M.026 (El) Valid until 17 December 2024 This Design Appraisal Document (D.A.D.) supersedes and cancels the previous D.A.D. No. RTS/ENG/140192 (Issue No. 0), dated 16 October 2014. The plans and calculations as listed in paragraph 1 of the Appendix have been examined for compliance with: Rules andRegulations for the Classification ofShips (Ship Rules), July 2079 Part 5, Chapter 6, Rules andRegulations for the Classification ofSpecialService Craft (SSC Rules), July 2079 Part 11, Chapter 2; Rules andRegulations for the Classification ofInland Waterways Ships (IWW Rules), November 2079 Part 5, Chapter 4, and will be assigned an appraisal status, as indicated, in accordance with the following conditions and comments:A. Details Equipment : Forward Stern Tube Seal Type : Prime Blue Diameter Range : 0 41 mm - 0 700 mm Propeller Shaft Lubrication Approved Oil Gland Suitable for SCM Descriptive Note : Water : No : No FINAL ACCEPTANCE OF ACTUAL ITEM(S) DEPEND(S) ON SATISFACTORY SURVEY AND TESTING Lloyd's Register EMEA Is a subsidiary of Lloyd's Register Group Limited Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register' . Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. Form 6438MARREF (2013 12) Lloyd's Register EMEA Rotterdam Technical Support Office K.P. van der Mandelelaan 41a, 3062 MB Rotterdam P.O. Box 701, 3000 AS Rotterdam Tel: 50 88, Fax 84 E: @Ir.org W: http://www.lr.org Document no: Issue number Page 2 of 4 Date 18 December 2019 RTS/ENG/140192 1 Please quote this reference number on all future communications RTS/ENG/195207/GKV/VSZ B. Mandatory Requirements:- 1. It is noted, that the PRIME Blue Seals are not adjustable from within the vessel and therefore AQS each type of PRIME Blue Seal is to be installed in combination with an inflatable seal. The arrangements are to be such, that the sealing ring with garter spring (Pos. 1) can be replaced with the ship afloat. a. For twin- or multiple screw vessels a brake or alternatively a locking device of robust construction is to be fitted, in order to prevent the shaft from rotating, in case the inflatable seal is pressurised after possible failure of the PRIME Blue Seal. b. For single-screw vessels a complete spare sealing ring with garter spring or a complete set of working parts, for each type of PRIME Blue Seal fitted, is to be available on board. Thereby accomodating replacement of the seal with the ship afloat whenever considered practicable. C. Manufacturers instructions how to replace the seal with the ship afloat are to be carried on board. 2. The axial sealing of the sealing ring is to be maintained also when the shaft line will be installed under slope conditions. 3. The PRIME Blue Seal arrangements are to be capable of accommodating the effects of differential expansion between hull and line shafting for all water temperatures in the proposed areas of operation. C. General Comments:- 1. The seals are to be installed in accordance with the Manufacturer's instructions and to the AQS requirements of the Rules, and tried under working conditions, all to the attending Surveyor's satisfaction. 2. The relevant materials to be made and tested in accordance with the "Rules for the AQS Manufacture, Testing and Certification of Materials". 3. The locking or securing arrangements to be to the Surveyor's satisfaction. AQS 4. Vessels, built in compliance with the Ship Rules, being fitted with these type of seals will not be eligible for the Notation "O.G." in the Register Book (Part 5, Chapter 6, Section 3.12.7 refers). 5. It is noted, that forced water lubrication will be provided and reference is made in this respect AQS to the applicable requirements, mentioned in the following paragraphs of the Rules:- FINAL ACCEPTANCE OF ACTUAL ITEM(S) DEPEND(S) ON SATISFACTORY SURVEY AND TESTING Lloyd's Register EMEA Is a subsidiary of Lloyd's Register Group Limited Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. Form 6438MARREF (2013.12) Lloyd's Register EMEA Rotterdam Technical Support Office K.P. van der Mandelelaan 41a, 3062 MB Rotterdam P.O. Box 701, 3000 AS Rotterdam Tel: 50 88, Fax 84 E: @Ir.org W: http://www.lr.org Document no: Issue number Page 3 of 4 Date 18 December 2019 RTS/ENG/140192 1 Please quote this reference number on all future communications RTS/ENG/195207/GKV/VSZ - Part 5, Chapter 6, Sections 3.12.2 & 3.12.3 of the Ship Rules. - Part 11, Chapter 2, Sections 4.16.4 & 4.16.5 of the SSC Rules. - Part 5, Chapter 4, Sections 3.11.2 & 3.11.3 of the IWW Rules. 6. For the relevant screw shaft Survey intervals reference is made to the following paragraphs of the Rules:- - Part 1, Chapter 3, Section 17.1.4 of the Ship Rules. - Part 1, Chapter 4, Section 10.1.4 of the SSC Rules. - Part 1, Chapter 3, Section 15.1of the IWW Rules. 7. An instruction plate is to be fixed to the bulkhead in way of the gland, clearly explaining the AQS purpose of the inflatable seal and that the shaft line is to be locked when subject seal is in use. eecchho.o. Support Offire Oft L Register EMEA Vishal Shenoy Senior Specialist Engineering Systems Rotterdam Technical Support Office FINAL ACCEPTANCE OF ACTUAL ITEM(S) DEPEND(S) ON SATISFACTORY SURVEY AND TESTING Lloyd's Register EMEA Is a subsidiary of Lloyd's Register Group Limited Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. Form 6438MARREF (2013.12) Lloyd's Register EMEA Rotterdam Technical Support Office K.P. van der Mandelelaan 41a, 3062 MB Rotterdam P.O. Box 701, 3000 AS Rotterdam Tel: 50 88, Fax 84 E: @Ir.org W: http://www.lr.org Document no: Issue number Page 4 of 4 Date 18 December 2019 RTS/ENG/140192 1 Please quote this reference number on all future communications RTS/ENG/195207/GKV/VSZ Appendix 1. The documents listed below have been examined Document No. Rev. Title A-04-2-0000-000-00A A-04-2-0000-000-00 PRIME Blue Seal General Arrangement PRIME Blue Standard Dimensions Status Date AQ 16-Oct-2014 SI 16-Oct-2014 Appraisal Status Key AQ Approved subject to matters raised that require resolution -- and provided the arrangements are to the Surveyor's satisfaction. AQS Details to be submitted by the client to the local surveyor's Office responsible for surveying the building and the arrangements verified in accordance with the Rule/Regulations requirements by the surveyor. SI Retained as supporting documentation for information only. The date is the date with which the document is stamped. 2. The documents listed below have been considered together with the submitted documents in the appraisal Drawing No. 12238-2 14020601 SG-13.1504 Dated 06-12-2013 06-01-2014 09-12-2013 Title Test Report Testing various profiles Certificate of mating ring Pressure Test Report version 10-11-2013 FINAL ACCEPTANCE OF ACTUAL ITEM(S) DEPEND(S) ON SATISFACTORY SURVEY AND TESTING Lloyd's Register EMEA Is a subsidiary of Lloyd's Register Group Limited Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register' . Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. Form 6438MARREF (2013 12)