Document 9Mm2EN94b9bwq9ELpjyJeYyL

JA COMPLETE LINE OF INSULATIONS for temperatures up to 1200 Now. Owens-Corning Fiberglas offers the best and most com plete line of modern industrial insulations for temperatures up to 1200CF. available from a single sdurce. Fiberglas can furnish either rigid or flexible insulation for every type of pipe, duct, and equipment commonly used in today's com plex industrial and commercial field. The Fiberglas name assures efficiency, lasting serviceability, and sure, long-range economy. Fiberglas Dual Temperature Pipe Insulation Fiberglas Dual Temperature Pipe Insulation is fibrous glass insulation with a factory-applied vapor barrier to prevent condensation on cold pipes. For temperatures up to 450F. Fiberglas Aerowrap* Pipe Insulation Fiberglas Aerowrap is a wrap-around insulation made of fine glass fibers, in resilient, light weight blanket form. Versatile and efficient. For all temperature ranges up to 600F. industrial INSULATIONS up to 1200 Fiberglas AE Board Fiberglas AE Board is made in rigid panels of glass fibers enclosed in asphalt. Designed for low tempera ture service at temperatures ranging up to 100=F. Fiberglas Metal Mesh Blanket Fiberglas Mefal Mesh Blankets are made of fibrous glass wool, faced on one or both sides wtth wire mesh or metal lath. Ideal for equipment with irregular surfaces. Fiberglas No. 600 Block Insulation Fiberglas Block Insulation is cut to lagging sizes and sanded on one side to form rigid blocks. For use on regu lar surfaces where temperature ranges do not exceed 450:F. Fiberglas PF Pipe Insulation Fiberglas PF Pipe Insulation, made of fibrous giass wool, is resin bonded and molded in cylindrical form. Recommended for all temperatures up to 450F. Fiberglas TW-F Insulating Wool Fiberglas Insulating Wool is a multi purpose product offered in roll, batt, bulk, or shredded form. Excellently suited for a wide range of applica tions up to 1000CF. Fiberglas Blanket Type Pipe Insulation Fiberglas Blanket Type Pipe Insula tion is Fiberglas Insulating Wool faced with wire mesh. Available for pipe sizes from 3 to 42 inches. For temperatures up to 1000F. Fiberglas PF Insulation Fiberglas PF Insulation is made in rectangular panels of rosin-bonded fibrous glass wool. Resilient, light, and easy to handle. For temperatures up to 450F. Kaylo Pipe Insulation Kaylo Pipe Insulation is made of a compound of lime and silica in pre formed segments for pipe sizes to 23 inches. For temperature ranges up to 1200F. Kaylo Heat Insulating Block Kaylo Heat Insulating Block is made of a lime and silica compound in 6, 12, and 18 inch widths and thick nesses from 1 to 3 inches, for service up to 1200F. Aefa^'op or > Corporation. OWENS CORNING FIBERG CORPORATION 3 V I &Z FIBERGLAS PF PIPE INSULATION Description Fiberglas PF pipe Insulation is made of fine-fibered glass wool, resin bonded, and molded in simplified di mensional standards, to fit pipe surfaces. It is recom mended for pipes operating at temperatures up to 450F. The resilient fibers mesh at the joints to give continuous, effective insulation. PF Pipe Insulation is available with a variety of factory applied jackets for use indoors or out, on heated lines. Properties PF Pipe Insulation is light in weight and easy to handle yet dense enough to be strong and durable. Like other Fiberglas materials, it resists moisture, will not support combustion, and has exceptional physical stability. Its low thermal conductivity is illustrated by the graph at right. Sizes Fiberglas PF Pipe Insulation is available for iron pipe sizes from Vi inch through 33 inches and for copper tubing sizes from 2^ inch through 6 inches. It is supplied in 3 foot lengths. Sizes and thicknesses available are given in table on opposite page. Advantages Efficiency--Fiberglas PF Pipe Insulation is first in effi ciency among molded materials within its service range. Its intricate maze of fibers traps countless tiny pockets of still air--one of nature's best insulators--and effec tively reduces heat loss. Resiliency--The resiliency of the glass fibers enables PF Pipe Insulation to resist damage from constant vibration or from thermal shock due to rapid tempera ture change. . Incombustible--PF Pipe Insulation, in common with other Fiberglas products, will not support combustion. Nesting Sizes--PF Pipe*-Insulation is manufactured in accordance with the "new simplified dimensional stand ards". The outside diameters conform to standard pipe diameters. This permits easy nesting and gives a wider selection of insulation thicknesses for multiple layer construction. Easy Installation--PF Pipe Insulation is easy to cut and fit. A knife is the only tool needed. The insulation can be "tailored" to fit standard pipe couplings for a neater, more effective application. Finer fibers make the product pleasant to handle. Limitations PF Pipe Insulation should not be used on pipes operat ing at temperatures above 450F. For low temperature lines. Dual Temperature Pipe Insulation is recommended. If PF Pipe Insulation is used on low temperature lines, a suitable vapor-barrier jacket must be installed over the insulation. The insulation should be protected from mechanical damage in locations where it will receive abuse. 8 The standardization of Fiberglas PF Pip* Insulation sizes, to conform to simplified dimensions, mokes possible reductions up to 40 per cent in inventory lists and storage space requirements. THERMAL CONDUCTIVITY _l 1 [ 1 i II 1 1 1 I 1 FIBERGLAS PF PIPE INSULATION T el C ctprk1 ot Vorp g, V on Tem rvfv'tft __________ 1 T : i fj/I // Ii ii 1i i i1 i ; ii iI j1 1 i 11 1 :i I> <**04f<** ------- ----------------- - '--i------- O SO 100 ISO JCO MO 300 350 Mean Tmperetge, deg f & RECOMMENDED THICKNESSES Insulation Thickness--inches To give insulotion surfoce temperatures below 1 20 P. Steam Pressure Operating or Condition Temp. F. Up to 1 Hot Woter 0 to 25 lb 25 to 100 lb 100 to 200 !b Low Super Heat 212 213-267 268-338 339-388 389-450 A A 1 1 l'A Pipe Sizes--inches i'/-s 6-8 9-12 AA 11 11 1 1VS I'/j 2 1 1 1 1A 2 14 and Up _ 1 1 1 1 'h 2 *Many services permit higher or lower surface temperatures and eA'C'e"^^ Recommended thicknesses for surfoce temperatures of 110, 1 30 nd . . ovoiloble on request. . Standard Sizes, Thicknesses and Forms pipe ipoulai ion up to 450 * thickness may b mode up of multiple Joyers on pipe lines up to 4'. 2 A thickness is single loyer only on pipes over 6". Copper Tubing* Tub!mg Actual Nominal '/a O.D. Actual 0.0. .50 .50 1.50 .63 .50 1.62 .75 .50 1.75 .88 .50 1.86 1.13 .50 2.12 1.37 .50 2.37 1.63 .50 2.62 Nominal 1 Actual O.D. 1.19 1.12 1.06 1.00 .91 1.06 .94 2.88 2.88 2.88 2.88 2.88 3.50 3.50 Nominal 1 Zi Actual O.D. 1.50 1.76 1.62 1.56 1.48 1.56 1.68 3.50 4.00 4.00 4.00 4.00 4.50 4.50 Tubing Size Actual Nominal Zi 0.0. Actual 0.0. 2' 2.12 .50 3.12 2'/:, 2.62 .50 3.62 3' 3.12 .50 4.12 3l/x' 3.62 .50 4.62 4' 4.12 5' 5.12 6' 6.12 Nominal 1 Actual O.O. 1.19 .94 1.28 .97 1.25 1.25 1.25 4.50 4.50 5.56 5.56 6.62 7.62 8.62 Nominal 1 Vi Actual O.D. 1.72 1.47 1.75 1.50 1.75 1.75 1.75 5.56 5.56 6.62 6.62 7 62 8.62 9 62 4Pper tubing insulation conforms to iron pipe sixes except of Zi' thick insulation. OWENS-CORNING FIBERGLAS CORPORATION OW ?N S -CORNING Recommended Application Fiberglas PF Pipe Insulation is suited for use on piping at temperatures up to 450F. It may be used on indoor or outdoor lines. When used outdoors a waterproof jacket should be used to protect the insulation. On piping operating above 450F., PF Pipe Insulation can be used as a second layer insulation over Kaylo pipe insulation. The inner layer should be thick enough so that its surface temperature does not exceed 450F. Nesting sizes permit the combination of PF Pipe Insula tion with these materials to take advantage of its extra efficiency. Coverings Canvas--For pipe sizes up to 12 inches, insulation is furnished in matched half cylinders covered with a factory-appiied standard canvas jacket, forming hinge and lap. For larger pipe sizes, insulation is supplied in segments. Separate jackets of heavier canvas are avail able on request. Waterproof Jacket--Where PF Pipe Insulation is to be used outdoors, or where the insulation is subject to occasional wetting, a suitable waterproof roofing felt jacket may be ordered in place of the canvas. Strips of the same material, 4 inches wide, are provided to cover joints. Other waterproof jacketing materials are avail able on request. Suggested Specification Insulating Material All pipes designated for operating temperatures up to 450SF. (where noted on drawings or listed in schedule) shall be insulated with Fiberglas PF Pipe Insulation as manufactured by Owens-Coming Fiberglas Corporation. Material'"sKall be applied (in the thickness shown on drawings or list) (to a..................thickness). Application All pipe insulation shall be applied over clean, dry su.-. faces, butting adjoining sections firmly together and pasting canvas, when furnished, smoothly over joints Insulation on pipes through 12 inches in diameter shall be secured with metal bands spaced on not greater than 18-inch centers. Insulation on pipes over 12 inches in diameter shall be wired in place with No. 16 soft annealed wire. Where double layer insulation is applied, the first layer shall be wired in place without jacket; the second layer shall be applied with all joints staggered. All flanges, valves and fittings shall be insulated with pre-molded fitting insulation, equal in thickness to the insulation on the adjoining pipe; field fabricated insula tion (mitered segments of rigid insulation wired in place) or Fiberglas Aerowrap wrapped to the desired thickness. Surface Finish Indoor piping through 12 inches in diameter not subject to abrasion or mechanical abuse requires no finish in addition to the factory-furnished canvas and bands. Piping over 12 inches in diameter shall be finished with canvas pasted in place. Piping located outdoors shall be finished with factoryapplied waterproof jacket with longitudinal joints lapped not less than 2 inches. All transverse jacket joints shall be covered with factory-furnished waterproof strips secured with two loops of No'."16 galvanized soft an nealed wire. Each section shall be wired with additional loops. Field-fabricated insulations on flanges, valves and fittings where required shall be covered with a 14-^ch coat of finishing cement. Portland cement to a maximum of 25% dry weight may be added if a harder finish is desired. Fitting insulation located indoors shall be fin ished writh canvas neatly pasted in place. All insulation on flanges, valves and fittings located outdoors shall be covered with asphalt weatherproof mastic, reinforced with an open mesh glass fabric. Mastic shall be applied in sufficient thickness to give a dry coat and shall be troweled neatly over the fitting and lapped over the jacket on the adjacent pipe. A knif* it th* only tool n**d*d to cut and fit Fiberglas PF Pipe Intulotion where a coupling changes th* pip* contour. 10 Th* result it o neat, ff*ctiv* application, with no interruption o smooth outer surface of fh* pipe insulation. r r up to 1000* 6 Description Fiberglas Blanket Type Pipe Insulation is made of Fiber glas TW-F Insulating Wool- It is faced on one side with I-inch ''straight line" wire mesh, secured to the wool by asbestos yarn ties. The strong wire mesh is cut to the right length to fit each pipe size. Selvages for easy, long lasting application are fabricated from 26-gauge sheet metal, folded twice, and crimped about the cut ends of the wire to form a metal edge 34 inch wide. Blanket Type Pipe Insulation is designed for insulating , pipes from 3 inches to 42 inches in diameter, operating at temperatures up to 1000F. |; Properties All the general properties common to Fiberglas insula tions are present in Fiberglas Blanket Type Pipe Insula tion. It resists moisture, will not support combustion, will not rot, and will not cause or accelerate corrosion of metal pipe. Its thermal conductivity averages .25 Btu,sq.ft./ degree F. at 75F. mean temperature* Advantages Versatility--Its flexibility makes Fiberglas Blanket Type Insulation ideal for spiral-riveted or spiral-welded pipes of irregular dimensions and for normal high tem perature lines where metal or roofing felt finishes are desired. . Efficiency--Interlocked glass fibers form countless tiny pockets which trap still air and provide high insulating efficiency. Jjasy Application --Its light weight makes this insula tion easy to handle. Application consists of wrapping the "blanket" around the pipe and lacing or tying the facing selvages together. Fiborglos Blanket Type Pipe Insulation U light in weight, eaty to hand!# in oven the most inaccessible places, and easy to apply. Finishes Insulation on indoor or outdoor piping should be jack eted. One suitable finish is 55-lb. roofing felt, lapped 2 inches at every seam. The roofing felt is secured with No. 16 wire or with bands. Finish can also be a galvanized sheet metal jacket with seams lapped 2 inches against the weather and secured in place with sheet metal screws on 6-inch cen ters, or with metal bands. A sheet metal screw attached at each lap of jacket sections will prevent slippage on vertical runs of pipe. All flanges, valves, and fittings should be finished wit! two 3^-inch layers of Fiberglas O-C Mastic reinforces with a tight wrapping of an open mesh glass fabri> between the layers of mastic. Application Fiberglas Blanket Type Pipe Insulation is applied over dry pipe, with all edges tightly fitted together. The longitudinal selvage edges are laced or tied together w*th wire. On bends, the selvages should be laced or tied together fhe outside radius of the bend and the wire mesh on be inside radius of the bend shortened to conform to ^be contour of the pipe. Ranges, valves, and fittings can be insulated with lerglas Metai Mesh Blankets. They are formed to fit i2*t.Cu^ w^er necessary. All cut edges are laced together wire. RECOMMENDED THICKNESSES Insulation Thi< i*-- ir.chos Tomporaturt Kongo F. 3-4 Vi Pip* Six** -- nch*t 5-10 12 and Up Up to 300 301 to 400 401 to 500 501 to 600 601 to 700 701 to 800 801 to 900 901 to 1000 1 IVi 2 2 Vi 3 3 3 Vi 3 Vi 1 2 2 Vi 2!i 3 3 Vi 4 4 Vi 1 2 3 3 3 Vi 4 4 Vi 4 Vi OWENS-CORNING FIBERGLAS CORPORATION OWENS-CORNING I Ftb ERfhAgr KAYLO PIPE INSULATION Description Kaylo Pipe Insulation is made of a chemical compound of lime and silica which needs no added binder. A small amount of asbestos fiber is included at the time of manufacture. Kaylo Pipe Insulation is suited for use on pipes operating at temperatures up to 1200F. It is manu factured by Owens-Illinois Glass Company and dis tributed nationally by the Owens-Coming Fiberglas Corporation. Properties Kaylo Pipe Insulation resists moisture. It is incombus tible and dimensionally stable. Its coefficient of thermal conductivity is very low among products in its tempera ture range as shown by the graph at right. Sizes Owens-Coming Fiberglas Corporation can supply Kaylo Pipe Insulation in semi-cylindrical sections for pipes up to 12 inches in diameter and in three-segment units for pipes up to 23 inches. See the table on page 13. The segmented construction of Kaylo Pip* Insulation moans aaty installation. Simplified dimensions assure snug and accurate netting. Limitations Kaylo Pipe Insulation is designed for pipes operating at temperatures up to 1200F. THERMAL CONDUCTIVITY Advantages Efficiency--Kaylo Pipe Insulation offers exceptional in sulating value. So small and so numerous are its insu lating air spaces that they present a material internal surface of approximately 100 acres per cubic foot of insulation. Resistance to Moisture--Water does not break down the structure of Kaylo. Even saturated, it retains an appreciable percentage of its strength. After being soaked for long periods of time and then dried, it returns to its original thermal efficiency and strength, without apparen^_ghrinking or warping. Easy Application--Kaylo Pipe Insulation is light and easy to handle. Its sectional or segmented construction makes it easy to apply. Long Service--Kaylo remains strong and efficient over the years. It shows little shrinkage even after constant, prolonged exposure to temperatures up to 1200F. Versatility--Kaylo performs efficiently on temperatures through the hot water and low pressure steam range and also through temperatures in the superheated steam range. Kaylo can be used alone for high temperatures which usually require combinations of two different insulating materials. Single layer application, for labor saving, is possible on pipes operating up to 700F. ' Nesting Sizes--Outside diameters of Kaylo Pipe Insu lation correspond to outside diameters of standard pipes. Where multiple layer application is needed, all layers nest perfectly to provide high efficiency at any desired thickness. 12 RECOMMENDED THICKNESSES Resulting in Maximum Surface Temperature of !30F. at 80F. Ambient* Operating Tomporaturo *F. Nominal Pipe Slxe 4 % 1 1 Vi 1 Vi 2 214 3 4 6 8 10 12 14 1 6 and Up 280 380 480 580 680 780 880 980 1080 200 1 t 1 1 1 1 1 1 1 54 1 54 1 54 1 54 1 'A 300 1 1 1 1 1 1 1 1 154 154 154 154 154 154 154 Tempo ratwre Oiff srtnee SF. 400 1 154 154 154 154 1V4 2 114 154 2 2 2 2 2 2 500 1 54 1 54 1 54 2 2 2 2 2 2 2 2 54 2 54 2 54 2 54 2 54 600 1 54 2 2 2 2 54 2 254 2 54 2 54 2 54 2 54 3 3 3 3 700 2 2 2 2 54 254 214 3 3 3 3 3 3 54 3 54 354 4 800 2 54 2 54 2 54 254 3 3 3 3 354 3 54 354 4 4 4 4 Vi 900 3 3 214 3 3 'A 3 3 3 54 3'4 4 4. 4 54 4!4 5 5 1000 3 3 54 3 3 54 34 34 4 4 i iA </i 5 5 54 54 3 54 3 54 34 VA 4 l 4A i'A i'A 5 5 554 514 6 6 *Mony services permit higher or lower surface temperature* and Recommended thicknesses for *urface temperatures of 1 10, I 20 n available on request. pipe INSULATION I 6t up to 1200 # Q\ Standard Sizes, Thicknesses and Forms NOMINAL THICKNESS OF INSULATION FORMS inol 1 O.D. Actual O.D. A' V*' 1' IK' .84 1.05 1.32 1.66 1.00 .90 1.08 .90 2.88 2.88 3.50 3.50 1% 2 2 V2 3 3J/j 4 Actuo 0.0. Actual O.D. Aeluo 0.0. Actual O.D. Actual O.D. Actuo O.D. 1.56 1.46 1.58 1.40 4.00 jNSSr |^36 -2.88 4.00 m* Sew X2< 536 ,2.77 '6.63 A 63 4.50 am 3.u:: -7\63 4.50 :c5.-56 1.2.17 W?* 2.97 ;7.63 41/2 5 Actuo O.D. Actuo O.D. I A' 2' Vh' 3' 1.90 2.38 2.88 3.50 1.03 1.Q3 1.03 1.00 4.00 4.50 5.00 5.56 3'/i* 4' 4/t' 5' 4.00 4.50 5.00 5.56 .75 1.03 .78 1.00 5.56 6.63 6.63 7.63 6' 6.63 ,94 8.63 7' 7.63 8' 8.63 9' 9.63 10' 10.75 n' 11.75 12' 12.75 14' 14.00 1.53 1.56 1.31 1.53 5.00 2**2 >5.56 5.56 ;.2.09: <6,63 5.56 *.M4` ^6.63 6.63 hjxi' ?7.63' 135 *6.63 2,59 ^ ^7;63 '2.3V v>`63 %Si. |?.63 2.85 7.63 3.09 8.63 2.84 8.63 3.03 19.63 3.59 9.63 3.34 9.63 3.59 iq.75 4.16 3.91 4.09 10.75 10-75 1 1.75 4.66 4.41 4.59 11.75 11.75 12.75 5.16 4.91 5.22 12.75 12.75 14.00 1.28 1.53 1.28 1.50 6.63 8' k&63 TZ2S m3 7.63 C.^03.- *8&3 ;`2:'S3. *9.t>3 7.63 M.78" && 2.28 ;.9.63 8.63 2.00 9.63 1^56 -1075 2.78 9.63 3.09j 10:75 2.84~1 10.75 3.061 11.75 3.34 3.59 3.34 3.56 10.75 11.75 11.75 12.75 3.84 4.09 3.84 4.19 11.75 12.75 12.75 U.OO 4.34 4.72 4.47 4.69 12.75 U.OO 14.00 15.00 4.97 5.22 4.97 5.19 U.OO 15.00 15.00 16.00 1.44 1.50 1.50 1.50 9.63 10.75 l 5.75 12.75 2.00 2.00 2.00 2.13 10.75 11.75 12.75 14.00 350 s&? 2.50 12.75 2.63 u.oo 2.63 15.00 3.00 12.75 3.13 14.00 3.13 15100 3.13 ; 17.00 3.63 3.63 3.63 3.63 U.OO 15.00 16.0Q 17.00 4.13 4.13 4.13 4.13 15.00 16.00 17.00 18.00 4.68 16.00 4.68 17.00 4.63 18.00 4.63 19.00 5.13 5.13 5.13 5.13 17.00 18.00 19.00 20.00 1.56 1.56 1.55 1.42 14.00 15.00 16.00 17.00 2.06 2.06 2.05 1.92 15.00 16.00 17.00 18.00 2.56 2.56 2.55 2.42 16.00 I3S6s 17.00 17.00 3.06; 18.00 18.00 3.05 19.00 19.00 m ?P 3.56 3.56 3.55 3.42 18.00 19.00 20.00 21.00 4.06 4.06 4.05 3.92 19.00 <4.56 20.00 20.00 4.56 21.00 21.00 4.55 22.00 22.00 4.42 23.00 5.06 21.00 5.06 22.00 5.05 23.00 4.92 24.00 15' 15.00 16' 16.00 17' 17.00 18' 18.00 1.42 18.00 1.41 19.00 1.41 20.00 1.41 21.00 1.92 1.91 1.91 1.91 19.00 20.00 21.00 22.00 2.42 2.41 2.41 2.41 20.00 21.00 22.00 23.00 2TT00 2&00 23750 &? 342 3.41 3.41 3.41 22.00 23.00 24.00 25.00 3.92 3.91 3.91 3.91 23.00 24.00 25.00 26.00 4.42 4.41 4.41 24.00 25.00 26.00 4.92 4.91 25.00 26.00 19' 19.00 20* 20.00 21' '21.00 22' ;22.00 23.00 N < N * * 1.41 1.41 1.41 1.41 1.41 22.00 23.00 24.00 25.00 26.00 1.91 1.91 1.91 1.91 23.00 24.00 25.00 26.00 2.41 24.00 '-Salt 2.41 25.00 Yixto 2.41 26.00 `MSS jjjjj 3.41 26.00 T. Single loyer N|t; The shaded sizes in the toble above available in either single or double layers. Multiple Loyer J- Sectional Tri- Segmental ^eylo Pipe Insulation it light, strong and eoty to handle. It is effee v*ly and economically used on outdoor pipe lines. Simple and rapid installation is an important factor in the choice of pipe insulation. Kaylo installation costs ar low. OWENS-CORNING FIBERGLAS CORPORATION 13