Document 82QM4dRaXjE1j6b7pBJyQEe8k

Airflex iTSKDS- TJS.02 MATERIAL SAFETY DATA SHEET P&EPt&ED: Ane*3fc rmB SECTION 1 - IDENTIFICATION Product Manufacturer: Eaton Corp./Airflex Div., 9919 Clinton Rd., Cleveland, Ohio 44144 Emergency Phone No.: (216)281-2211 Person to Contact: Paul Showalter PRODUCT NAM(S): AIRFLEX PRODUCT MODELS: DP, HC, HD PRODUCT/MSDS APPLICABILITY: This MSDS applicable to said products manufactured amrttfnT r.. hjfiiv .pxiscjI'rt, tup h.ib color coded DP products, MSDS 15.01 is applicable through December 31,1988. See !abi'. rr. fr/natai 'or .idmtbicaiirrn nrnx- chrseoi manufacture. PRODUCT IDENTIFICATION: Said products are typically used as brakes and tensioners, wrth, Wtftte!marai'Hi!;cHrtfle'tftpj-a local ized color coding on the sides of the friction blocks, typically either light brown, red & white sr- gtaRTf-rtteit) ..totb.ist.'tijB.-t; if posi tive identification cannot be made, contact PRODUCT MANUFACTURER. SECTION 2 - HAZARDOUS INGREDIENTS AND EXPOSURE LIMITS HAZARDOUS INGREDIENTS Teflon WHERE USED In Friction Material* CAS NUMBER 9002-84-0 OSHA PEL Not Listed KOGH-I TO.' atQSIh, STEL * Teflon is used only in friction materials with green & orange color coding, and typicallyjrmiy-fa'rtjmsinnrt;: ru-iu/iatoabateine-? jyoe applications. NOTE: The listed hazardous ingredients are in a solid or encapsulated form after manufetetirimsatn? itehteatefir.rshcppe.t:, th:t:preventing generation of airborne dust containing said materials prior to product use. hnvreve, .htrs'idadosu' a-naii snntur-cs'i result in wear debris (typically dust) containing said hazardous materials. SECTION 3 - PHYSICAL AND CHEMICAL CHARACTERISTICS CHEMICAL Teflon BOILING POINT C N/A SPECIFIC GRAVITY 2.2 C TEMP. FOR VAPOR PRESS. = 1MM No Data VAPOR DENSITY N/A SOU>S 'WATS*! Irtsolttete TTofrr IN WATiv-t 'W/T- .we-. ruts ROh'D- C '4or..'u N/R - Non-reachvs 'N,*.- 34011 atpnircuita- SECTION 4 - FIRE & EXPLOSION DATA FLASH POINT: N/A FLAMMABLE LIMITS IN AIR. % BY VOLUME: LEL (LOWER) - N/A AUTO IGNITION TEMPERATURE: N/A UF.L IUPPE7V - N/A E>~INGUISHL`~. MEDIA dry chemical SPECIAL FIRE FIGHTING PROCEDURES: Full protective equipment with self-contained breathing jerparatus UNUSUAL FIRE AND EXPLOSION HAZARDS: Dust may present an explosion hazard if fine'j tfrrrdec .'dispersed trait,-and exposed to a source ot ignition. SECTION 5 - PHYSICAL HAZARDS AND REACTIVITY DATA STABILITY: This material is stable under normal conditions of storage, handling and use. INCOMPATIBILITY: None HAZARDOUS DECOMPOSITION PRODUCTS: None for products without teflon; products-with tetter mat emrt'hTresting fumes when heated above 260C (500F), and toxic fumes when heated above 400C (750F). HAZARDOUS POLYMERIZATION: None F:T*N * \ Page 1 of 2 ASARCO ELP 0000052 SECTION 6 - HEALTH HAZARDS AND FIRST AID MSDS 15.01 While this material presents no significant health hazards during normal storage, handling and use, exposure to dust or fumes from this material can cause irritation of eyes and/or respiratory system, and can be a serious heatth hazard and requires that special precautions be taken. See Sections 7 and 8 on Special Precautions and Protection. SYMPTOMS AND EFFECTS OF EXPOSURE TO TEFLON ARE AS FOLLOWS: No toxic effects are known to be associated with inhala tion or ingestion under normal conditions, but heating above 260C (500F) can cause decomposition which can produce injurious fumes, and heating above 400C (750F) can cause further decomposition which can produce toxic fumes; however, no lethal effect has been documented regarding human exposure. Rather, inhalation of said decomposition fumes can cause temporary influenza like symptoms (described as "polymer fume fever*), including fever, chills, cough, and malaise. Said symptoms do not normally occur until at least 2 hours after exposure, and usually cease within 48 hours after exposure, even without medical treatment. Obser vations have indicated that effects of said exposure are not lasting and are not cumulative. SYMPTOMS AND EFFECTS OF EXPOSURE TO ASBESTOS ARE AS FOLLOWS: Symptoms of overexposure are labored breathing, coughing, tightness or pain in chest, and weakness; symptoms usually will not manifest until 15 to 20 years after exposure. Effects of overexposure are irritation or damage of the pulmonary tissue, asbestosis, and possibly cancer (suspected carcinogenic per 29 CFR 1910.1200.) PRIMARY ROUTES OF ENTRY: Inhalation of dust or fume; ingestion of dust MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Respiratory problems in general, and dermatitis. INHALATION: Remove victim to fresh air, obtain medical attention. EYES: Bush with water to remove particulate, obtain medical attention. SKIN: Wash thoroughly with soap and water; if irritation develops, obtain medical attention. INGESTION: Obtain medical attention if quantities are ingested. SECTION 7 - SPECtAL PRECAUTIONS AND SPILL/LEAK PROCEDURES HANDLING & STORAGE: In general, no special precautions in handling and storage are required. However, good housekeeping practices should be observed to prevent any accumulations of dust, and contact with incompatible materials should be avoided as stated in Section 5 on Physical Hazards. RELEASE OR SPILL Any release or spill which may involve dust should be vacuumed or wet-swept to avoid generating airborne dust. WASTE DISPOSAL Follow local, state, and federal regulations for disposal of solid, encapsulated, or powdered (wear debris-typically dust) waste containing specified hazardous ingredients. SECTION 8 - SPECIAL PROTECTION & CONTROL MEASURES INFORMATION RESPIRATORY PROTECTION: Use NIOSH approved respirator if exposure to dust or fume is possible. VENTILATION: Local and/or general exhaust should be used to keep airborne contaminants below TLV's. PERSONAL PROTECTIVE EQUIPMENT: Gloves or barrier creams may be necessary to prevent dermatitis. Approved goggles or safety glasses should be worn if dust or chips are generated. Exposure to dust or fume may require protective clothing and ad ministrative hygienic practices as described in the OSHA Asbestos Standard, 29 CFR 1910.1001. The information provided above is for the sole purpose of complying with the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information is given in good faith and comes from sources believed to be accurate and correct, but is given without warranty of any kind. Eaton Corporation assumes no responsibility for the results of its use. Page 2 of 2 V ASARCO ELP 0000053