Document 6bBRDVYwRYK7ovoG5o5QDGOkE

68 . CHAPTER 3 - -1949 Guide Solution. At 63 F the value of the saturation pressure is 0.58002 in. Hg. There fore, at atmospheric pressure (29.921 in. Hg), p. = 0.58002 - 29.341 X 27/2739 = 0.2908 in. Hg The relative humidity is y> = 0.2908/1.4219 = 0.2045 . .. the denominator being the value of saturation pressure at 90 F. ' From Equation 16 may be computed the corresponding degree of saturation, the result being A = 19.67 per cent in remarkably close agreement with the answer to Example 2. STEADY FLOW ENERGY, EQUATION ." In steady flow, the energy convected by the fluid at any section is the sum of (a) kinetic energy due to velocity ; (b) gravitational energy due to elevation; (c) enthalpy due to the condition of pressure, temperature and composition of the fluid.. , .... ... Kinetic Energy ''' There are reasons to believe that the so-called velocity pressure h, read by a. Pitot tube' is simply the kinetic energy, per unit volume of the fluid immediately upstream from the-tube,, as. application , of Bernoulli's Equa tion suggests. Thus- -7 V = 1097 3 /(23) where / V = velocity, feet per minute. h, = velocity pressure, inches of water at 60 F. - p = density of fluid, pounds per cubic foot. '' / " In the case.of flow through a duct, the velocity pressure is found to-vary considerably over the section and a traverse has to be made. The crosssectional area of the duct is divided into a number of equal concentric areas, and measuring stations are located at centroidal points in each area along two perpendicular diameters. Usually the ultimate object is to determine an average velocity V from which the weight of fluid crossing the section per unit time can be obtained on multiplying by the crosssectional area of the duct and by the density of the fluid. This is obtained by simply averaging the square roots of all measured velocity pressures as follows: where 1097.3 v;.. m (24) average velocity, feet perminute. AT = arithmetic average of the square roots of all'measured velocity pressures, inches of water at 60 F. But the item of present importance is the average kinetic. energy con- Thermodynamics 69 vected with each pound of fluid. Consistently with the previous discus sion, this can be shown to be -- ' (A)i; ' KE = 0.006678 ^ '(25) KE = average kinetic energy, Btu per pound. v = specific volume, cubic feet per pound.' = arithmetic average of the 3/2-powers of all measured velocity pressures, ' inches of water at 60 F. If the velocity pressure were uniform over the section. Equations 24 and 25 could be combined to give ' (26> But it is interesting to note that if the. velocity varies parabolically from zero at the walls to maximum at the center as it does in the case of purely viscous flow in a circular duct, then the average kinetic energy is twice that given by Equation 26. Example 19. If 2000 cfm of air flow through an 8 in. diameter circular duct, find the average kinetic energy per pound of air. Solution. The cross-sectional area of the duct is 0.349 sq ft; hence the average flow velocity is 5730 fpm. If the velocity were uniform over the section, the average kinetic energy would be (5730 + 13,430)* = 0.182 Btu per pound. But it is more likely that the actual distribution of velocity would approximate that characteristic of viscous flow; hence the average kinetic energy would be more nearly 2 X 0.182 = 0.364 Btu per pound. Gravitational Energy The potential energy due to elevation Z (feet) above, any convenient - datum is simply Z -5- 778.3 Btu per pound of fluid. In the case of moist air. 2(1 + WO PE = 778.3 (27) where ~PE = average potential energy, Btu per pound dry air. Z = average elevation, feet. : IF = humidity ratio, pound water per pound dry air. Enthalpy ;; ' No further discussion of enthalpy is required. It may be Well'to em phasize, however, that enthalpies have been figured on the basis of one pound of dry air. Heat and Shaft Work Between any two sections 1 and 2 in an apparatus through which: steady flow occurs, there may be heatabsorbed from outside 172, Btu per pound of dry air, and shaft work removed to outside, iU, Btu per pound of dry air. If heat is actually rejected to outside, 13- is intrinsically negative; and if shaft work is actually put in from outside, ih is intrinsically negative.