Document 65v152jvamBLaLj7ajkOZDe8o

PACO TEXTURES joint treatment product data General Limitations Joint Finishing 1. For interior use only; not intended (or use on wood, wood fiber products, or unprtmed concrete. 2. Each coal of joint compound must be dry before next is applied. Completedjoint treatment mutt be thoroughly dry before proceeding with painting or other decoration. 3. Avoid application during unfavorable temperature and atmospheric conditions 4. Warranty is void if any Paco product is adulterated with plaster, whiling or other materials. 5. Protect all ready-mixed or job mixed materials from b. Avoid ovcrlhinning of materials. Overthinning will im pair bonding strength and cause excessive shrinkage. 7 Use soft dean water above 50* to mix or thin Paco products. Hard or cold water can prevent some of the In gredients from going into solution, thereby affecting the quality of the product. 9. Bagged products require protection against damp storage areas or wetting 9 Controlled ventilation is required for proper drying con ditions. Windy, drally, dry conditions and low humidity may cause cracking in joint compounds. 10. Industry problems such as beading, and edge cracking arc not the responsibility of the product manufacturer and no warranty is caprested, implied, or made for this type of problem. Warranty KELLY-MOORE PAINT COMPANY INC.* MAXIMUM LIABILITY FOR WARRANTY OF THIS PRODUCT, EXPRESSED OR IMPLIED. SHALL BE LIMITED TO THE PURCHASER S COST OF THE PRODUCT ITSELF. The statements made in this bulletin or by any of our agents concerning this product are given for information only. They are believed to be true and accurate, and are intended to provide a guide to approved drywall construction prac tices and materials. As workmanship, weather, equipment, quality of other materials and other variables affecting results are all beyond our con trol, Kelly-Moore does not make, nor does it authorize any agent or representative to make any warranty, expressed or implied, concerning the MERCHANTABILITY OR FITNESS of this product. For satisfactory results, this material must have good drying conditions until it it thoroughly dry. Relative humidity above 60% or below 10%, or surface and air temperalure above II0*F or below 50*F, and Inade quate ventilation, are unsatisfactory drying con ditions BUYER AND USER ACCEPT THE PRODUCT UNDER THESE CONDITIONS " joint treatment products specification guide PACO TEXTURES CORPORATION PACO TEXTURES joint treatment product data PACO TEXTURES decorative textures product data Ready-Mix Compounds PACO PROOUCT NO. 4051 Ready-Mixed All Purpose Joint Compound A premised material designed to bond tape to wallboard for reinforcing and concealingjoints. Ready to use feature eliminates cosily mixing lime, provides easy sanding, minimum shrinkage, smooth workability, uniform con* sistency, and mists cracking when properly applied. Formulated to provide long storage life, and may also be used for topping and texturing. PAC0 PRODUCT NO. 4151 OReady-Mixed Topping Compound A premixed material designed to HU and finish taped joints, nuit heads and metal corner bead. Ready to use feature eliminates cosily mixing lime: provides easy sanding, minimum shrinkage, smooth workability, uniform con sistency; and resins cracking when properly applied. For mulated to provide long storage life 00 NOT USE TO F.M8EO TAPE Dry Powder Compounds PACO PROOUCT NO. 5525 Taping CompoundDesigned for embedding tape only. Formulated (or positive bond, smooth workability, and to resist edge cracking when property applied PACO PRODUCT NO. 35)5 DFinishing CompoundDesigned to fill and finish taped joints, nail heads, and metal corner bead. Dry powder packaging allows savings In freight and storage Foimulated to provide easy san ding, minimum shrinkage, smooth workability, uniform consistency, and resists cracking when properly applied. DO NOT USE TOEHBEO TAPE PACO PRODUCT NO. 5512 Vinyl All-Purpose Compound Designed as a thrcc-in-onc product which can be used for taping, topping and texturing of interior surfaces. Dry Powder Compounds (continued) PACO PRODUCT NO. 8815 All-Purpose CompoundDesigned as a Ihree-in one product which can be used for taping, topping and featuring of Interior surfaces. |Ons Oar Join! Byalam Compound) DQuik Set Joint Compound NO. 8S88 Extra Slow NO. 5590 Stow (7 to I hour kI) (2% to 5 hour set) NO. 5591 Fast (90 minute set) Designed to cut drying time or taped joints and to per form under slow drying conditions. Varying conditions will alter dry lime. May alto be used as first coat over naif heads and metal corners. To be finished with Paco Topping Compound. Available in Ihrec ranges of selling lime. Additional i Drywall Products ! | |Dri-WallTape A spark perforated reinforcing paper tape used in joint concealment and reinforcement in drywall construction. This high-quality paper It spark perforated and has chamfered edges to resist edge cracking. Pic-creased feature allows casv folding for corner application. [ |Tru-Line Metal Corner Bead NO. 501 NO. 50) (ll/l"x 11/8" x| ) (1-1/4" a 11/4" a 8 ) A light gauge electro galvanized metal corner bead.which is nailed lo external wallboard corners with a minimum of six fasteners on each face. The metal cornet reinforces, protects and finishes the wallboard around window and door openings, and at intersection* with other materials PACOPRODUCTNO. 4301 Paco-Crete Concrete Surfacing Compound PACO-CRETE is a ready mixed surfacing compound treatment designed lo HU small pits, voids and hide minor surface Irregularities on Interior Concrete, Walls and Ceilings prior lo finishing. Decorative Textures Ceilings (simuwwj acouuc> PACO PRODUCT NO. 5373 Deco-Tex Ceiling TextureA spray applied ceiling texture designed to provide an economical and eye-appealing coarse, white texture and finish over drywall and concrete ceilings. Blended aggre gate gives rough texture that reflects and diffuses light, thereby concealing minor blemishes. PACO PROOUCT NO. 9)74 Deco,-Tex Celling TextureA spray applied ceiling texture designed with lest aggregate to provide a finer appearing while texture and finish over drywall and concrete ceilings. Blended aggre gate produces a medium coarse texture that reflects and diffuses light, thereby concealing minor blemishes. Surface Preparation Ceilings -Concrete WA'AIIllccooncrete fins shall be ground off lo equal smoothness of adjacent concrete areas. All exposed iron or steel surfaces shall he spot primed with one application of a suitable Kelly-Moore primer. Form board seams shall be lopped with a |0" to 12" wide lopping coat of Paco Ready-Mixed Topping Compound All air pockets or holes so surface shall he filled flush with the surface. Decorative Textures Walls & Ceilings PACO PRODUCT NO. 55S5 Wall & Ceiling TexlureDesigned lo provide a wjde variety of textural patterns by varying the method of application Texturing provides a decorative background and conceals minor blemishes I I Surface Preparation L__J Walla A Calling*-Oypaum Wallboard _ wallboard joints are to he reinforced with drywall tape. AUcxtcrnal corners should he protected with Paco Truline Melul Coiner Beads Conceal taped joints, metal corners, nail heads Or screw depressions with joint compound flush wth the surface Decorative Textures Walls & Ceilings (continued) NOTE To insure uniform textural appearance, it is neces sary lo teal wallboard or concrete ceilings to provide n even surface poroxily-Appiy one coat of Kclly-Moore Vinyl Sealer and allow lo dry before texturing. Q Textural Patterns a. SKIP TROWEI.: A rough tenure for walls and ceilingslhal is hand applied hy trowel producing a ran dom pattern by leaving the wallboard intermittently exposed Sand may he added lo the texture material to produce a more coarse texture. 5 b. SI'l.ATIF.R: A rough spray applied feature splattered over the surface and left untrowcled The sire anddepth nf the pattern can be varied and general ly fifty percent of the wall area is randomly textured t. KNOt K 1>t>WN: A rough texture that is spray applied and troweled down to produce a fiat high/low pebble-like pattern 4. H>t,: A fine sprayed-on texture that is splattered and Troweled down lo produce a flat high/low pebbk-like pattern Prior joint treatment should be for smooth wall construction. e. ORANfif. PEF.I.: A spray applied texture over the eatire field of Ihc board similar to a Fog pattern, hut producing a rounded,peak and valley through the use o! special equipment. Pattern can vary from a light lo a heavy textured finish. Prior joint treatment should be for smooth wall construction. (. ROLLER TF.XTURF.: The texture is applied with a hand roller over the entire surface The degree of tex ture is dependenton theconsislcncy ofthe jointcement or manufactured texlure material and the nap of the roller used. For special effects, applique rollers may be u*ed. Prior joint treatment should be for smooth wall construction. QTextural Samples The textural pattern of these basic textures can be varied depending on application techniques When a particular pattern or finish isdcsired.il is recommended that fhcappli tator first make a sample for approval.