Document 4J5xeQ0zKnjb9V9xxJZ8k52qQ

_ Heating Systems Burners, on York-Shipley, Inc. Main Office and Plants--York 16, Pennsylvania OIL-FIRED EQUIPMENT FOR INDUSTRY HORIZONTAL ROTARY BURNERS STEAM-PAK GENERATORS Model AHPM direel-drive fully automatic pump-type burner with full modulating sys tem, for heating or process work. Uses No. 6 oU. York-Shipley Horizontal Rotary Burn ers cover the range from 45 to 400 boiler hp, and are built in direct-drive and beltdrive types. Models are offered for use of fuel ons No. 1 through No. 6 (light dis tillate to most viscous bunker oils), for manual, semi-automatic, or full modulat ing control, with or without pumps. The extremely wide range of models and sizes, high efficiency, and adaptabil ity of this line assures easy selection of the right unit to fit any type or shape or make of boiler, with long life ana low operating cost. Three significant engineering develop ments provide precision combustion. The Iris Shutter, which gives absolute con trol of burner air, causing metered vol ume of burner air to remain constant; The Flame-Former, which shapes the flame to fit combustion chambers of any type; and The Automatic Torch Lighter, a pressure-type igniter for smooth and positive automatic starting. All York-Shipley Industrial products are sold, engineered and installed by local distributors who have been selected because of their knowledge of engineering and of equipment using heavy oils. Model SPLSO-5 low-pressure boiler for heat ing applications. A three-pass, down-draft, horizontal fire tube design. Uses No. S oil. Steam-Pak Generators are built both for low-pressure heating load and for high-pressure process load, in sizes from 15 hp up. Using fuel oils No. 3,5, and 6, or gas or combination they require only a low-cost vent to remove products of combustion. With about half the size, weight, and installation cost as compared to brick-set boilers of comparable capacity, SteamPak Generators require only four simple service connections, and are completely wired, piped, and pre-tested at the factory. Ready to operate when de livered. The Steam-Pak Generator is an effi cient unit, combining the oil burner and boiler in one package. It is designed to operate at peak efficiency through the entire firing range. This is accomplished with the Iris Shutter and modulating pump. A COMPLETE LINE OF INDUSTRIAL COMMERCIAL AND RESIDENTIAL EQUIPMENT York-Shipley, Inc. builds a complete line of automatic heating equipment. Be side the Horizontal Rotary Burners and Steam-Pak.Generators for industrial and commerical use described here, we offer the famous York-Heat boiler-units, winter air conditioners, water heaters, and con version burners for either oil or gas. 1394 INTERNATIONAL HEATING & VENTILATING EXPOSITION THE AIR CONDITIONING EXPOSITION Permanent Address--Grand Central Palace, New York 17, N. Y. EXPOSITIONS HELD Philadelphia, 1951; Chicago, 1949; New York, 1948; Cleveland, 1947-1940; New York, 1938; Chicago, 1936; New York, 1934; Cleveland, 1932; Philadelphia, 1930. FUTURE SCHEDULE The 1953 Exposition will be held at International Amphitheatre, Chicago, 111., January 26 to 30, 1953. UNDER AUSPICES OF A.S.H.V.E. These Expositions have been and will be held co-incident with the annual meetings of The American Society of Heating and Ventilating Engineers and under their auspices. Management is by International Exposition Company with permanent headquarters at Grand Central Palace, New York 17, N. Y. EXHIBITORS Comprise leading firms in each phase of the industry; number has varied from 150 to 400 exhibitors. EXHIBITS These range from and comprise all the types of articles discussed or advertised in this copy of The A.S.H.V.E. Guide. 1. The Combustion Group: Furnaces, burners (coal, oil and gas), grates, stokers, boilers, radiators (vari ous types), refractories and auxiliaries. 2. The Oil Burner Group: 3. The Hydraulic Group: Water feeders, water heaters, pumps, . traps, valves, piping, fittings, expansion joints, pipe hangers, etc. 4. The Steam Heating Group: Vapor heating, steam specialties. 5. The Hot Water Heating Group: 6. The Air Group: . Warm Air furnaces and stoves, registers and grilles, cooling towers, air filters, motors, fans, blowers, conditioning equipment, ventilators (room and indus trial types), unit heaters, etc. 7. The Air Conditioning Group: Equipment which circulates and filters the air, in summer dehumidifies and cools; in winter heats and humidifies, and does all these in proper season for com plete, all year-round air conditioning. 8. The Control Group: Instruments of precision for indicating, controlling or recording temperature, pressure, volume, time, flow, draft or any other function to be measured. 9. The Refrigerating Group: Compressors, condensers, cooling appa ratus, contingent apparatus and refrig erants. 10. The Central Heating Group: Apparatus and materials especially de signed or adapted to the uses of central heating and central heating station sup plies. 11. The Insulating Group: Structural insulators (refractory and cellulose materials), asbestos, magnesia clays and combinations thereof, pipe and conduit covering, etc., weather-stripping, etc. 12. The Miscellaneous Group: Electric Heaters, boiler and pipe repair alloys, liquids and compounds, tools of all kinds, and equipment not specifically included in the above groups, but related thereto. 13. The Machinery and General Equipment Group. 14. Books and Publications. VISITOR ATTENDANCE Attendance is by invitation and regis tration only, thereby presenting a selected audience. Included are con tractors, dealers, jobbers, supply houses, home owners, industrial users, professional and service organizations, public utilities, real estate management concerns, etc. A detailed analysis of registered attendance is available on request. Industrial Expositions in America lead the expositions of the world in style, business effectiveness, industrial influence and educational value. This Exposition.stands among the leaders in Industrial Expositions in America.. It is an educational institution which brings together the research develop ments and improvements in equipment and materials for use in heating, venti lating and air conditioning all types of buildings.