Document 3QekX0OvqJJ2Nx0grv4LDk38E

t * * MATERIAL AND APPLICATION SPECIFICATIONS FOB WEATHER-BARRIERS, VAPOR-BARRIERS, FINISH COATINGS, INSTALLATION ADHESIVES AND FIRE PROTECTIVE COATINGS USED WITH THERMAL INSULATION SYSTEMS AUGUST 1971 VIMASCO COATINGS CORPORATION P. O, BOX 5X6 NITRO. WEST VIRGINIA, 25143 PHONE: (304) 755-3323 pVS. CoA. SBCoOx aCuO,AuTlItNraG,SwC.OvBP,.sits i PfHt /. ' ' Contents Aug. 1971 ' CONTENTS Number TITLE PAGE--------------------------------- ----------------------------------------------------------------------------------------------- i INTRODUCTION:-----------------------------------------------------------------------------------------------------------------------------ii TABLE OF CONTENTS ----- ----------------------------------------------------------------------------------------------------------- iii SECTION 1--MATERIALS SPECIFICATION LIST OF MATERIAL SPECIFICATIONS 1.2.1. Poly-Vinyl Acetate Emulsion Weather-Barrier Mastic-Fibrated--------- ---------- VIMASCO . Product Pape Number See. No. _ ................WC-1 1-4 1.2.2. Fire Retardant Polyvinyl-Acetate Weather-Barrier Mastic-Fibrated-------------------- . __WC-1 FR 1-6 1.2.3. Acrylic Emulsion Weather-Barrier __ ... AC-7 1-8 1.2.4. Polyvinyl-Acetate Emulsion .#708 1-10 1.3.1. Polyvinyl-Acetate Emulsion Lagging Adhesive and Coating 4 #136 1-11 1.3.2. 1.4.1. 1 A 9n 1.4.3. iii. 1.6.1. 1.7.1. 1.7.2. Polyvinyl-Acetate Emulsion Heavy Viscosity Lagging Adhesive and* Coating Cold Bond Adhesive and Sealer TTeaf Resistant Sealer Polyvinyl-Acetate, Cork Filled, Caulking and Fillet Compound Vinyl Resin Anti-Abrasive Coating . Rubber Base Duct and Lap Adhesive Clear-Amber color .. _ Rubber Base Duct and Lap Adhesive #713 #750 #49 ... #703C - #500 .... #730 #731 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1.7.3. 1.8.1. L9.L Duct and Lap Adhesive-Nonflammable W** Dry Vapor-Barrier Insulation Coating Polyvinyl-Acetate Cork Filled Tnsnlatinfr Mastin #733 #740 1-20 1-21 WC-ITvneC 1-23 1.10.1. uia. High Temperature Insulation Adhesive RvfenaihTe Reinfrirring Clnth #760 1-25 . _ _ _F1astafah #8941-26 U1.2. U.L3. 1.1L4. UL5. Glass Reinforcing Cloth Canvass Ashestns Clnth Wire Netting 1-26 1-27 1-27 1-27 VPI.MOA. SBCOOX 5C1O0,ANTlItNroG,SWC. OvRP,.2SI43 ill t CONTENTS--(Couu) SECTION 2--APPLICATION SPECIFICATIONS List oi Application Specifications 2.1. 2X 2.3. 2.4. 2.5. 2.6. 2.7. 2.8. 2&: 2.10. Z1L 202. Z13. 204 205. 206. 207. Weather-Barrier Installation over Rigid Insulation on Moderate and High Temperature Equipment and Pipe, (Polyvinal-Acetate Mastic) _ Weather-Barrier Installation over Rigid Insulation on Moderate and High Temperature Equipment and Pipe (Acrylic Mastic) Indoor Finish. Installation over Rigid Insulation on Moderate and High Temperature Equipment and Pipe Adhesion and Sizing of Cloth Covers over Rigid Insulation on Moderate and High Temperature Equipment and Pipe Installation of Duct Lining Flexible Insulation to Air Conditioning and Heating Ducts Installation of Duct Lining Rigid Insulation to Air Conditioning and Heating Ducts= Installation of Flexible Insulation to Exterior of Air Conditioning and Heating Ducts Installation of Rigid Insulation to Exterior of Air Conditioning and Heating Ducts Weather-Barrier Installation over Sprayed Fibrous Insulation' on High Temperature Equipment (Polyvinyl-Acetate Mastic) Weather-Barrier Installation over Sprayed Fibrous Insulation on High Temperature Equipment (Acrylic Mastic) Joint Sealing and Weather-Barrier Installation over Cellular Glass In sulation nn T.nw Tamparature Equipment and Pipe Joint Sealing and Weather-Barrier Installation over Cellular Glass Insu lation on Low Temperature Equipment and Pipe Weather-Barrier over Sprayed Urethane Foam Insulation on Moderate Temperature Equipment fPnlwinvl-Anetate Mastic Weather-Barrier over Sprayed Urethane Foam Insulation on Moderate Temperature Equipment fArrvlio Mastic Vapor and Weather-Barrier Installation over Rigid and Semi Rigid In sulation on Low Temoerature Equipment and Pipe Vapor and Weather-Barrier Installation over Rigid and Semi Rigid In sulation on Low Temperature Equipment and Pipe Vapor-Barrier and Finish Installation over Rigid and Semi Rigid Insu lation nn Tow Temperature 208. Cork Filled Mastic Installation on Equipment and Pipefor Condensation * Control 'VQCASCO C0ATPTC5 CSH2O. ass Sift. Stoo, W. ~?a*, 3SM3 Contents Au?. 1371 IMffC Sec, No. 2-4 2-7 2-10 2-12 2-15 2-16 2-18 2-20 2-22 2-25 2-27 2-31 2-34 2-35 2-36 2-40 2-43 2-45 TMASCO COATINGS CORP. *. O. Box 310, Kttro, W. Vm. 23143 August. 1971 J 1.1. 1.1.1. Ll.2. 1.1.3. 1.1.4. Material Speculations--Scope Ang. 1971 SECTION I MATERIALS SPECIFICATIONS WEATHER-BARRIERS, VAPOR-BARRIERS, INSULATING MASTICS, COATINGS AND ACCESSORIES SCOPE: These specifications provide the material specifications for weather-barrier mastics, vapor-barrier mastics, insulating mastics, sealers, anti-abrasive coatings, coatings and ac cessories used with, or for, thermal insulations. These specifications state the use for which the material is intended, the general description of the material, and the characteristics of the material which make it suitable for the intended use. These specifications shall be used for the procurement of materials. The installation procedure for various installation services are provided in the APPLICA TION SPECIFICATIONS. ' The individual material specifications are given individual number designations for easy reference in the INSTALLATION SPECIFICATIONS. Specified material shall have the properties as given in its individual number designation. The individual number designations of material.* are as follows: VS&ASCO COATINGS COBP. P. O. BOX Uf, Htxto, W. VA, 25243 1-1 J * Sec. Material No. No. MATERIA I 1. 11.3. Canvas__________________________________ ____________________ 1. 11.4. Asbestos Cloth ___________________________ -------------------------- 1. 11.5. Wire Netting__________________________________________ ______ 1. 11.6. Lacing Wire - -- PAINTS-COATINGS 1. 12.1. Polyvinyl-Acetate Emulsion Paint__________________________ 1. 12.2. Vinyl-Chloride Solvent Paint_______________________________ 1. 12.3. High Temperature Aluminum Paint________________________ PRIMERS 1. 13.1. Iron Oxide-Zinc Yellow Metal Primer_____________________ 1. 13.2. Polyvinyl-Acetate Primer-Sealer -- ----- -- - 1. 13.3. Utility Primer---------------------------------------------------------------------- 1. 13.4. Universal Primer .________________________ ~ -- -. . - FIRE-RETARDANT PAINTS-COATINGS L 14.L Fire Retardant Paint------------------------------------------------------------1. 14X Eire Retardant Coating---------------------------------------------------------X. 14J3. Fire Retardant Varnish (Clear)______________________________ 1. 14.4. Fire Retardant Paint Topcoat_______________________________ SOLVENTS AND THINNESS L I5J. Aromatic and Ketone Solvent_______________________________ L 15.2. Aromatic and Ketone Blend Solvent _____________________ L 15.3. Aromatic Thinner--------- -- -- -- ----- -- -- 1. 15.4. Aromatic Aliphatic Naphtha Thinner_______________________. 1. 15.5. Aromatic and Ester Thinner____________________________ - L 15.6. VM and P Naphtha Thinner_________________________________ Material Specifications--List Aug. 1371 V1MASCO Product Page Number Sec^No. _________ 1-27 _________ 1-27 _________ 1-27 _________ 1-27 .Liquid Vinyl ,PVA 1-28 .#10 1-29 .#811 1-31 _P.OP. #52-8 1-32 -P.OP. #52-4 1-33 1#925 1-34 _#926 1-35 P.OP/#52-10 1-36 P.OP/#62-10 1-37 -P.OP. #52-7 1-38 _P.OP.'#52-6 1-40 #49-T -#500-T P.OP. #52-10-T P.OP. #52-T P.OP. #52-7T P.OP. #52-6T 1-41 1-42 1-43 1-44 L-45 1-46 VIMASCO COATINGS CORP. P. O. Box ua. Nitre. W. Va, 2S143 1-3 L2.L6. Material Specification L2X Polyvinyl-Acetate Mastic WC-i Auff. 11)71 Flexibility_________ Hardness----------- '__ Impact Resistance__ Puncture Resistance .Bend 180 over W* mandrel in 10 seconds at 25 F without cracking .75 (approximately) Shore Durometer, Type A gauge .Excellent Excellent Resistance to: Acids______________________ Weak Alkalis Strong Alkalis____________ Asphalts__________________ Salts _____________________ Solvents__________________ Temperature Limits, Maximum Tensile Strength______________: Weather Resistance___________ Water Vapor Permeance______ .Good for mild acids Excellent -Poor .Excellent Excellent .Good 200 F continuous 250 F intermittent .115 psi at 70 F Excellent .Not less than L0* perm (in accordance with ASTM E-96) Polyvinyl-Acetate emulsion -weather-barrier of these properties shall be WC-1, regular or spray grade, of color specified, as manufactured by Vimasco Coatings Corp. VOiASCO COATINGS CORP. P. O. 3ok.SU. NifiK, W. 7t.SU2 IrS * 1.23.6. Flammability________________ Flexibility--------------------------- Hardness_____________________ Impact Resistance___________ Puncture Resistance__________ Resistance to: Acids , Alkalis _______________ :___ Asphalts__________________ Salts_________________*___ Solvents__________________ Temperature Limit, Maximum Weather Resistance__________ Water Vapor Permeance_____ Material Specification I.2J!. ' tire ltetardant I'oiyvinyi-Acetate Mastic WC-IFK Aug. 1971 --........ASTM E-1G2-07 Radiant Panel Index shall be less than 5 _________Bend 180* over W* mandrel in 10 seconds at 25 F without cracking _________75 (approximately) Shore Durometer Type A Guage Excellent ------------- Excellent _________Good for mild acids ________ Excellent _________Excellent ________ Excellent _________Good ________ 200 F continuous 250 F intermittent _________Not less than 1.0 perm (in accordance with ASTM E-96) Fire Retardant Polyvinyl-Acetate Weather-Barrier Mastic of these properties shall be WC-1 FR, Regular or Spray Grade, color as specified, as manufactured by Vimasco Coatings Corp. p vucasco DATINGS COBP. P. Q. Sex I, Nfcro, W. V* 1-7 . Material Specification 1.2.3. Acrylic i'olymcr Mastic AC-7 Auff. 1971. Flammability .............................................. ...... ........ . -----ASTM E-1G2-G7 Radiant panel flame spread index shall be less than 15 Flexibility___ .. -- . -_____ __ __________ Bend 180 over y>n mandrel at 5 F without cracking Hardness'.23.6, approximate) by Shore Duro- meter, Type A Gauge Impact Resistance--------------------------------- ---------------------- Excellent Puncture Resistance---------------------------------------------------- Excellent Resistance to: Acids __________________________ ____ --Good for mild acids Alkalis------------------------------------------------------------------- Excellent AsphaltsExcellent Salts----------------------------------- ;---------------------------------- Excellent Solvents___________________________________ ________ Good Temperature Limits, Maximum200 F continuous 250 F intermittent Tensile Strength;i__100 psi at 70 F Water Vapor Permeance________________________ ______ Not less than 1.0 perm (in accordance with'ASTM E-96) Weather Resistance_______ ___ _ _^Excellent .6. Acrylic polymer weather-barrier-mastic of these properties sh*H be AC-7 Regular or Spray Grade, color as specified, as manufactured by Vimasco Coatings Corp. COATINGS COBP. ut Sic, Nitre. W. V* 23143 1-9 1.3.1. 1.3.1.1. 1.3.1.2. 1.3.1.3. L3.L4. 1.3X5. I.3.I.5.I. U.l.5.2. I.3.I.5.3. L3.1.6. Material SpcctUcauon l-i.i. l*olyvinyl-Acetale lunulsioii Lagging Adhesive and Coating *136 Aug. 1971 SECTION 1 MATERIAL SPECIFICATION POLYVINYL ACETATE EMULSION LAGGING ADHESIVE AND COATING #13G Intended Use: To adhere canvas, brattice cloth or asbestos cloth to thermal insulation and as an overcoat to seal cloth and present a pleasing finished surface. Shall be suitable where fire resistant and low flame spread surfacing materials are required. General Description: Shall be a brushing consistency of polyvinyl-acetate with selected fillers and required fire resistive compounds. Shall be suitable for application by brush or spray. Application Limits: Shall be suitable for application at ambient air temperatures down to 40 F. Color. Shall be white, but suitable for tinting with universal type colorants. Polyvinyl-Acetate Emulsion Lagging Adhesive and Coating shall have the following prop erties: Properties, Wet--shall be: Flammability__________________ --: Freeze-Thaw Stability----------------Odor -------------------------------------------pH----------------------------------------------Storage Stability Total Solids Content_______________ Total Solids Content---------------------- Viscosity ........... -- Weight per Gallon________________ .Nonflammable .Must be protected from freezing Mild . .7.2 to 7.5 .Two years at temperature above freezing. .53 -- 2% by weight .38% tz 2% by volume Brushing . . . 100 10 KU 11.0 lbs. 0.2 lbs. Properties, Application, shall be: Adhesion to Substrate______ . Application, Ambient Temperature Coverage as adhesive . As sizing coat_____________________ Drying Time _____________________ Solvent (while still wet) __________ Properties, After Drying, shall be: Abrasion Resistance _____ Adhesion to Substrate_____________ Flammability_____________________ Mildew Resistance________________ Resistance to: Alkalis_______________________ Asphalts______________________ Acids_________________________ Salts _________________________ Solvents: Temperature Limit, Mayrmim____ .Excellent Must be above 40 F .30 to 60 sq. feet per gallon .36 sq. feet per gallon .to touch--2 hours, through--12 hours .Water shall be used to cleanup drips and splatter of coating while it is still wet Excellent .Excellent .Shall meet requirements of Interim Federal Standard No. 00136 (ComNBS) Class 1 .Good .Good .Good .Good .Good .Good .200 F Lagging Adhesive of these properties shall be Vimasco-Lag #136 as manufactured by Vimasco Coatings Corp. . VXXASCO COATINGS CORP. P. O. Box 5M, ffltro, W. Va_ 2SX43 1-U 1.4.L 1.4.1.1. 1.4.1.2. 1.4.1.3. 1.4.1.4. 1.4. L5. 1.4.1.5.1, 1.4A5.2. 1.4.U5A L4.L6. SECTION 1 MATERIAL SPECIFICATION r1al<*rr:tl Sporifirjilioit l.l.J. C>iU IJ'Hui .'.uhcbivc ::m' Sealer J73U auj. ia"i COLD BOND ADHESIVE AND SEALER #750 Intended Use: For use as a cold bond adhesive and vapor barrier to bond and :;cal joints oi` low temperature insulation. Seal laps of metal jacketing. General Description: Shall be trowel consistency mastic having good initial adhesion and low water transmission rate when dried. Shall be suitable for application to foamed organic and rigid mineral wool fiber insulations. Application Limits: Shall be suitable for application at ambient air temperatures down to 20 F. Color: Shall be off white. Cold Storage Adhesive and Sealer shall have the following properties: Properties, Wet, shall be: FlammabilityFlash point shall not be lower than than 120 F Freeze-Thaw Stability------------------------------------------- ------ Not affected by Low Atmospheric . Temperatures OdorMild Storage Stability-- _. 2 years . Total Solids Content93 = 2% by weight ~ 36 = 2% by volume Viscosity .Soft paste mastic Weight per Gallon12.3 lbs. =*= 0.2 lbs. Properties, Application, shall be: Adhesion - -- -- ------- - - - - TVfglTpn* Bonding TimeGood initial bond Build ---------------------------------------------------------------------------1/16** to 1/8** thickness on vertical surface will not slip or sag Coverage---------------------------------------------------------------------- 50 to 75 sq. ft. per gallon as an adhesive 15 to 20 sq. ft per gallon for use as vapor-barrier Solvent . ,. . -- .............................. Most aliphatic organic solvents Properties, After Drying, shall be: Adhesion to Substrate . ... -..... Flammability ___________ :________ Flexibility - Puncture Resistance_____________ Impact Resistance_____ ________ Resistance to: Alkalis_______________________ Agiriq _ _ -- --------_ _ - Salts_________________________ Temperature Limits: Maximum - Minimum - .................. Water Vapor Transmission 1/16** film tfoWness _ -Excellent -Slow burning -Good -Good -Excellent -Good --Good ^Good _200 F -50 F -Not to exceed 0.6 perms (in accordance of ASTM E-96) Cold Bond Vapor-Bazrier Adhesive and Sealer of these properties shall be Vimosco #750 as manufactured by Vxmasco Coatings Corp. . vniAsco COATINGS CORP. P.O.Box as. Nitre. W. Va^ 23143 M3 , 1.4.3. 1.4.3. L. 1.4.3.2. 1.4.3.3. 1.4.3.4. 1.4.3J5. L4.3.6. SECTION 1 MATERIAL SPECIFICATION HIGH TEMPERATURE SEALER * Material Speciiication L4.3. High Tempera! are Sealer Aug. 1971 Intended Use: To be used as a fillet around hot projections through insulation. General Description: Shall be silicone base high temperature sealer. Paste consistency. Application Limits: Shall be suitable for application, at all ordinary ambient air temperatures. Colon Depends on manufacturer. High temperature shall have properties in accordance with the material specifications of approved manufacturer. High temperature sealer shall be as manufactured by Dow Chemical Co., or General Electric Co., or approved equal. VTKASCO COATINGS CORP. P. O. Sox su. Nitre, W. V*, 2SU3 1-15 1.6.1. 1.6.1X 1.6.L2. 1.6.L3. 1.6X4. 1.6X5. L6.L5.L 1.6X5X 1.6A.5.2. 1.6X6. Material Specification I.fi.l. Vinyl Resin Anti-Abrasive Coating #500 Aug. 1971 SECTION I MATERIAL SPECIFICATION VINYL RESIN ANTI-ABRASIVE COATING #500 Intended Use: A vinyl chloride based material for coating the face of cellular block in sulation and/or bore of cellular pipe insulation, next to substrate, to minimize fracturing and powdering out of cellular insulation due to vibration and movement due to expansion and contraction. General Description: Shall be a vinyl resin coating suitable for application to the insula tion by brush, or spray. The coating shall remain very elastic at very low sub-zero temperatures. Application Limits: Material shall be suitable for application at atmospheric temperatures down to 20 F. It shall be allowed to dry on the surface of the cellular glass for a minimum of 10 minutes before insulation is applied to pipe or vessel. Requires good ventilation during drying. ' Special Note: This coating shall not be used on insulation which is to be used to insulate austenitic stainless steel surfaces. Colon Shall be fiat brown--dries to straw tan. . Vinyl Resin Anti-abrasive Coating shall have the following properties: Properties, Wet, shall be: Flammability . . _ Storage Stability-----------------------Toxicity_________________________ Viscosity, Brush Grade_________ Weight per Gallon--Brush Grade -Flash point shall not be less than 40 F 2. years Requires ventilation .Light paste, (95-100 KU) .8.1 lbs. m Q.2 lbs. Properties, Application, shall be: Adhesion to Surface , Excellent Coverage--------------------------------------------- :-------------------------275 to 300 sq. ft/ gallon To obtain coating thickness of2 to 3 mill* Drying Time------------------.-----------------------------------------------10 minutes, to touch Solvent ------------------------ ----................. - . Vicarlon 500-T thinner Properties, After Drying, shall be: Abrasion Resistance_____ ,________ Adhesion to Cellular Glass_______ Flammability ................. , . Resistance to: Acids_________________________ Alkalis_______________________ Solvents -- ------------- --- Temperature Limits, Maximum___ Minimum' Toxicity__________________________ Excellent . .Excellent ' .Self .Good .Good .Depends on nature of solvent .Stable for 6 hours at 300 F .--150 F Non-toxic Anti-abrasion coating of these properties shall be #500 as manufactured by Vimasco Coatings Corp. .. VIMASCO COATINGS COBP. ' P. O. Box 518, Mitro, W. VA. 23143 1-17 1.7.2. I.7.2.I. 1.7^2. 1.7.2.3. 1.7.2.4. I.7.2.5. I.7.2.5.I. 1.7X52. 1.7JL5.3. L7J2.6. SECTION 1 MATERIAL SPECIFICATION Material Specification 1.7.2. Duct and Lap .lubber Base Adhesive White Color *731 Aug. 1071 DUCT AND LAP RUBBER BASE ADHESIVE (WHITE COLOR) #731 Intended Use: To bond laps of vapor-barriers, and adhere films, foils and laminates to insula tion. It also shall be suitable to adhere fibrous glass insulation to steel, galvanized steel, and aluminum air conditioning ducts. General Description: Shall be a rapid setting, rubber based adhesive suitable for appli cation by* brush or spray. Application Limits: Shall be suitable for application at atmospheric temperature down to 40 F. Shall be applied in areas of good ventilation and not near open flame. Color: Shall be white. Rubber Lap and Insulation Adhesive (Rapid Setting) shall have the following properties: Properties, Wet, shall be: Flammability---------------- Odor-------------------------- -- Storage Stability----------Total Solids Content____ Total Solids Content -- Toxicity_________________ Viscosity ________ Weight per Gallon Flash point shall not be less than 10 F .Strong 2 years .34 n 2% by weight .21 2% by volume Requires good ventilation Prolonged breathing of fumes, or contact with skin should be avoided. Brushing, (75 5 KU) 6.8 lbs. 02 lbs. Properties, Application, shall be: Adhesion to surfaces--------------------Coverage, Attaching Insulation----Coverage, Sealing Laps -------------Drying Time, Attaching Insulation Drying Time, Sealing Laps .. . Solvent_________________ _________ Properties, After Drying, shall be: Adhesion Flammability Flexibility Resistance to: Acids_________________________ Alkalis Salts_________________________ Solvents -- - Temperature Limits, Maximum___ Temperature Limits, Minimum ___ Toxicity__________________________ Excellent .50 to 75 sq. ft/galloa .60 to 80 sq. ft./galloa .0 to 15 minutes .0 to 15 minutes Hexane Excellent Meet Federal Interim Specification 00136B Excellent .Good .Good .Good Fair .225 F .5 F Non-toxic Duct and Lap Rubber Base Adhesive, of these properties, ghn be #731 Duct and Lap Ad hesive as manufactured by Vimasco Coatings Corp. VIMASCO COATINGS CORP. P. O. Box 41*. Nitre, W. Vi, 25143 1-19 1.8.1. SECTION I. ?.IATERIAL SPECIFICATION VAPOR-BABRIER INSULATION COATING #740 .Material SprvuuiUua Ijj.i. Vapor-Harrier Cwaiioc /710 Autf. :a;i I.8.I.I. Intended Use: To vapor-seal rigid insulation on surfaces operating below ambient air tem perature. Not recommended for outside exposure. 13.1.2. General Description: Shall be a heavy build mastic of soft smooth consistency. Shall be suitable for application by palming, brushing or spraying. I.3.I.3. Application Limits: Shall be suitable for application at ambient temperatures down to 20 F and not lower than 15 F for following 24 hours. 13.1.4. Color: Shall be White. ' X.8.1.5. Vapor-barrier coating shall have the following properties: 1.8.13.1. Properties, wet, shall be: Flammability . Odor___________________ Storage Stability------------ Total Solids____________ Total Solids____________ Toxicity -- -- --- Viscosity . Weight per Gallon______ Flash point shall be not lower than 90 F Mild solvent odor .2 years .67 =1= 2% by weight .44 2% by volume Requires good ventilation Soft paste consistency 10.7 lbs. m 02 lbs. 1.8.133. Properties, Application, shall be: Adhesion to Substrate__________ Build___ ________________________ Coverage_______________________ Shall obtain a__________________ Curing Time____________________ Solvent , .......... Precaution _____________________ Substrate 13033. Properties, After Drying shall be: Abrasion Resistance____________ .Excellent .1/16 inch thickness on vertical sur face shall not slip, slide or sag 35 sq. ft/gallon or 4 gallons per 100 sq. ft. .1/16 inch, wet thickness 1/32 inch dry thickness (approx) .Shall be approximately 2 hours to touch, 24 hours throughout Mineral spirits .Use with adequate ventilation, keep away from heat, sparks and open flame. .To be applied to clean and dry sur faces for good adhesion. Is suitable for application to cellular glass, rigid glass fiber, rigid urethane foam, and some grades of polystyrene foam. (Some styrene foams are subject to solvent attack) .Good VIMASCO COATINGS CORP. p. O. Box 31*. Nitre, W. Vo* 33143 1-21- 1.9.1. I.9.U. 1.9.1.2. 1.9.1.3. 1.9.1.4. 1.9.1.5. 1.9.1J5J.. L9.L5.2. 1.9.L5.3. SECTION X MATERIAL SPECIFICATION M:itcri:ti S|K*rili*aUm 1.3.1. folyvinyl-Acctalc. Cork Killed. Insulating Mastic WC-1 Type C Auff. 1371 POLYVINYL-ACETATE, CORK FILLED', INSULATION MASTIC WC-1 TYPE C Intended Use: To be used as insulation to retard condensation on the surface of equipment, tanks, or piping that operate at a temperature below the dew point of the ambient air. General Description: Shall be a polyvinyl-acetate emulsion resin with granulated cork, asbestos fibers and selected fillers to provide a heavy build mastic. After application and drying, the mastic shall be water resistant and have a relatively low thermal conductivity. Shall be suitable for application by trowel or spray. Application Limits: Surface to which it is applied must be dry. Surface temperature should be above dew point of ambient air until mastic has dried. Shall be suitable for application at atmospheric temperature down to 40 F. ' Color: Shall be as specified from standard available colors. Polyvinyl-Acetate, Cork Filled Insulating Mastic shall have the following properties: Properties, Wet, shall be: Alkalinity, pH............................................. .......................... 5.6 to 7.5 Flammability................ ....... ...... ............ ...... ................ " Nonllammablo Freeze-Thaw Stability...................................................... . Suitable to withstand temperatures ' down to 25 F for short period Odor................................................................ ..................... Mild Storage Stability..................... .................... .................... . . 2 years Total Solids Content ................ ....... ....... ................. . 61% -a 2% by weight Total Solids Content------------------------------------------------- 65% -a 2% by voiumc Toxicity-------------------------------------:............ ..... ............. ....... Non-toxic Viscosity---------------------------------------------------------------- Heavy paste Weight per Gallon____________________ _______ _____ 8.0 lbs. 0.2 lbs. Properties, Application, shall be: Adhesion to Dry Surfaces....................... .............. Excellent Build, Wet........... ........................ ................ ........................... on vertical surface will not . slip, slide or sag Coverage, to obtain dried............... ....................... 10% to 12 gal. per 100 sq. ft. Coverage, to obtain dried---------------- ---------------- 21 to 24 gal. per 100 sq. ft Curing Time......................................................... ................ To touch--1 hour Through, depend ing on thickness, 12 to 24 hours Shrinkage, Volume------------------------------ --------- ------------- - 25% to 35% by volume Solvent (while still wet) ---------------- --................ --..... Water, (as material has excellent ad '.................. hesion after it has dried, it is difficult to remove from tools or equipment. Therefore tools, spray guns, and pumps should be cleaned immedi ately after use. Properties, After Drying, shall be: ' Abrasion Resistance.................................. ......... .................... Excellent Adhesion to Substrate , . ` Excellent . 7QU5CO COATINGS COBP. P. O. Sox U. Nltro, W. Vft* 25143 1-23 1.10.1. 1.10.1.1. 1.10.1.2. 1.10.1.3. 1.10.1.4. L10.L4.1. Material Specification 1.10.1 iligh Temperature liuuiutiou Adhesive #7G0 Auff. 1971 SECTION 1 MATERIAL SPECIFICATION . HIGH TE?,1PEKATURE INSULATION ADHESIVE #760 - Intended Use: To bond calcium silicate, rigid asbestos-fibers, asbestos felts, and board to themselves and to nonporous surfaces. Of particular use for bonding cut high temperature insulation pieces together to form fabricated insulation, fittings and valve covers. General Description: A sodium silicate base with selected fillers to produce a brush or trowel consistency adhesive. Color: Shall be gray. High Temperature Fabrication Adhesive shall have the following properties: Properties, Wet, shall be: Flammability__________________________________________ Nonflammable 1.10.1.4.2. 1.10.1.4.3.\ L10.L5. Freeze-Thaw Shall not be allowed to freeze Total Solids Content, Brush Grade52 d= 2% by weight Total Solids Content, Trowel Grade55 2% by weight Viscosity, Brush GradeSoft paste ' Viscosity, Trowel Grade .Thick paste Toxicity________________ .Non-toxic Weight per Gallon, Brush Grade - .11.1 lbs. d= 0.2 lbs. Weight per Gallon,, Trowel Grade -9.B lbs. * 0.2 lbs. Storage Stability_________________ -2 years Properties, Application, shall be: Adhesion to Substrate--------------Bonding Time, Brush Grade Bonding Time, Trowel Grade Coverage, Brush Grade_____ Coverage, Trowel Grade____ Drying Time in Joints______ Solvent_ .Excellent ..0 to 10 minutes 0 to 20 minutes ______________ 50 to 75 sq. ft/gallon ____ __________ 25 to .50 sq. ft/gallon ______________ Approximately 2 hours _ ........... ..........Water Properties, After Drying, shall be: Flexibility....... ....................-- - Adhesion____ Flammability Temperature Limit, Max. Toxicity_________________ ___ --_____ Brittle ___________Excellent .. Non-combustible _100Q F -Non-toxic High Temperature Fabrication Cement shall be #760 Hi Temperature Insulation Adhesive. (Brush or Trowel Grade as specified) as manufactured by Vimasco Coatings Corp. VUIASCO COATINGS CORP. F. O. Sex SM, Nitre, W. V*. 23M3 1-25 1.11.3. 1.11.3.1. 1.11.3.2. 1.11.3.3L 1.11.3.4. Material Specification l.lt.3. 1.11.4, Canvass. Kelts, .Settings and Wire Aug. 1971 SECTION 1 MATERIAL SPECIFICATION CANVAS . Intended Use: As reinforcing cloth to form a finish system when embedded in mastic. Canvas for reinforcing mastic on equipment and vessels shall be 8 oz. canvas. Canvas for reinforcing mastic on pipe shall be 6 oz. canvas. Canvas for light weight indoor and concealed piping shall be 4 oz. canvas. 1.11.4. 1.1L4.1. 1.11.43. 1.11.4.3. ASBESTOS FELT Intended Use: As covering over insulation. Fabric shall be soft flexible asbestos felt in roll form. ' Thickness and weight per 100 sq. ft shall be as required and supplied for individual installation. 1.11.5. 1.11.5.1.1. 1.11.5.1X 1.11.5.13. WIRE NETTING Monel Wire Netting Intended Use: To reinforce weather-barrier mastic for outdoor and indoor installationswhere corrosive atmosphere is present Shall be 0.023" diameter wire woven to one inch hexagonal mesh. 48" wide. 1.11.53. Lll.53.1. 1.11.533. GALVANIZED WIRE NETTING Intended Use: To reinforce weather-barrier mastic finishes. Shall be No. 18 wire woven to one inch hexagonal mesh, galvanized after weaving. 1.11.6. 1.11.6.1. 1.11.63. LACING WIRE Intended Use: To secure insulation to surfaces and to lace wire netting together. Shall be stainless steel wire, 0.0475 inch diameter (18 gauge) dead soft annealed 302, 304, or 430 stainless steel wire. VXMASCO COATINGS CORP. P. O. Bex 314. Nitre. W. Va, 23143 1-27 SECTION I MATERIAL SPECIFICATION Material Spurili^uioa I.IUJ*. Vinyl-Chloride I'auU HQ ' Aug. 1371 1.1Z2. VINYL-CHLORIDE PAINT #10 1.12.2.1. Intended Use: To be used as a protective and decorative finish coating for both interior and exterior exposure. For coating wood, metal, concrete and weather-barriers, finishes and jackets covering thermal insulation- Aluminum and galvanized steel shall be primed with polyvinyl-acetate paint and ferrous metal shall be primed with Iron Oxide-Zinc Yellow Primer prior to application of the Vinyl-Chloride Coating. Also used with weather-barrier mastics in requirements calling for resistance to caustic. 1.12.2.2. General Description: Shall be solvent vinyl-chloride coating suitable for brush or spray. Fast drying. Dries to smooth semi-gloss finish. Shall be resistant to acids, alkalis, and salts. 1.12.2.3. Application Limits: Shall be suitable to be applied to surfaces not exceeding ISO F in tem perature and shall be suitable for application at ambient air temperature down to 20 F. 1-12.2.4- Color: Shall be as specified. (16 std. colors + black, white, aluminum). 1.122L5. Properties: Vinyl-Chloride Solvent Paint shall have the following properties: 1.12.2.5.1. Properties, Wet, shall be: Flammability___________ Total Solids_____________ Weight, lbs. per Gallon__ Odor-----------------------------Storage Stability----------Viscosity________________ ZFlash point shall not be lower than 75 F -32 i 2% by wgt -3.1 lbs. : 0.2 lbs./gaL -Strong odor (solvents) -At least 2 years _75 d= 5 KU 122222. Properties, Application, shall be: Adhesion to Substrate__________ Coverage_______________________ Drying Time____________________ Time Between Coats__________ -- Solvent __________ _____ Toxicity _______________________ 1.123.5.3. Properties, after Drying, shall be: Abrasion Resistance_______________________ Adhesion to Substrate -------- --....- Contraction and Expansion with Substrate Light Stability Resistance to: Acids_________________________________ Alkalis! Hydrocarbons --______________________ Temperature limit, May.__________________ .Good 225 sq. ft per gallon, 1 mil, thick .20 minutes to touch, 12 hours solvent free Not less than 30 minutes MIBK .Use with adequate ventilation, avoid prolonged breathing of vapors and repeated contact with skin Excellent .Good Shall conform without cracking Excellent Not affected by most acids Not affected by most alkalis .Good for most .140 F (continuous) VIMASCO COATINGS CORP. P. O. Box 316. Nitro, W. V*, 23143 1-29 1.12.3. 1.12.3.1. 1.12.3.2. 1.12.3.3. 1.12.3.4. 1.12.3.5. 1.12.3.5.1. 102^.5.2. 1.123.5.3. 1.123.6. Material Specification 1.12.3. Ilifh Temperature Aluminum Paint #811 /Vug. 1971. SECTION 1 MATERIAL SPECIFICATION HIGH TEMPERATURE ALUMINUM PAINT #811 Intended Use: To be used as paint over metal which operates at high temperature. Shall be suitable as a coating over steam lines, boiler casings, boiler drums, or other equipment oper ating at high temperatures. General Description: Shall be a heat resistant formulated coating suitable for application by brush or spray. Application Limits: Shall be suitable for application to surfaces not exceeding 100 F in temperature and shall be suitable for application at ambient air temperature down to 40 F. Color: Shall be aluminum. Properties: Heat resistant paint shall have the following properties: Properties, Wet, shall be: Flammability __________ Odor----------------------------Solids Content__________ Storage Stability-----------Weight per Gallon______ Viscosity _______________ __Shall have a flash point not lower than 80 F t __Strong E-Not less than 30% by weight Minimum 2 years __8.1 lbs. 0.2 lbs. __60 5KU Properties, Application, shall be: Adhesion to Substrate__________ Coverage ______________________ Drying Time .............. --...... . Solvent ________________________ Time Between Coats____ ________ Toxicity _______________________ Excellent 550 to 650 sq. ft. per gallon to obtain 1 to 0.75 mil dry thickness To touch 2 hours, through 6 hours Xylol 4 hours Use with adequate ventilation. Avoid prolonged breathing and re peated contact with skin Properties, after drying, shall be: Abrasion Resistance------------------Adhesion to Substrate__________ Contraction and Expansion_____ Light Stability--------------------------Resistance to: Acids_______________________ Alkalis Hydrocarbons ______________ Salts_______________________ Temperature Limits, Max._____ ! Excellent Excellent Shall conform without cracking Excellent Good Good Fair Good 500 F continuous 600 F intermittent Heat resistant paint of these properties shall be #811 Hi-Temperature Aluminum Paint manufactured by Vimasco Corp. . VOCASCO COATINGS CORP. P. O. Box US, NttTO. W. Vft, 2S143 1-31 1.13-2. 1.13.2.1. 1.13.22. 1.13-2.3. 1.13.2.4. 1.132.4. 1.13.2.5.1. U32.52. 123222. L1322.4. Material Spcciiication 1.13J2. Polyvinyl-Acetate Primer-Sealer P.OJP. #52-4 Aug. 1371 SECTION X MATERIAL SPECIFICATION POLYVTNYL-ACETATE PRIMER-SEALER--P. O. F. #52-4 Intended Use: As a primer over galvanized steel, aluminum, asphaltic weather or vaporbarriers, new wood, and wallboard. General Description: Shall be a polyvinyl-acetate base Tor priming materials and acting as a base for vinyl paints and coatings. It shall be suitable for a base material over which fireretardant paint or coating will be applied. It shall not cause interference with the intumescent reaction necessary for the function of lire retardant paint or coating. It shall be suitable for application by brush or spray. Application Limits: Shall be suitable for application at ambient air temperature down to 40 F. Color: Shall be white. Properties: Polyvinyl-Acetate Primer and Sealer shall have the following properties: Properties, Wet, shall be: Flammability___________ Freeze-Thaw Stability -- Odor -------------------------- -- Storage Stability________ Viscosity_______________ Weight per Gallon______ Solids __________________ .nonflammable .Should not be allowed to freeze .Mild .1 year .Brush, spray (78 to 82 KU) .10.4 lbs. a 02 lbs. .41=tr2% Properties, application, shall be: Adhesion to Substrate-----------------------Coverage ---------------------------------- ;-------- Drying Time .................. - .. ... Time Required Before Overcoating___ Toxicity_____________________________ ^ Solvent (while still wet)_____________ .Good 275 sq. ft per gallon to obtain 1 mil thickness 20 minutes to touch, 1 hour to cure .4 to 6 hours Non-toxic .Water Properties, after drying and in service: Adhesion to Substrate___ 1_____________ Flexibility ___________________________ As Substrate Coating________________ Good .Conforms without cracking Suitable base for polyvinyl acetate base paint, .polyvinyl acetate cork filled mastics, fire retardant paint and coating Polyvinyl-acetate primer-sealer shall be P. Q. 7 #52-4 primer-sealer as manufactured by Vimasco Corp. VP.nioA.SBCfOl* COATINGS CORP. Ut, Nltro, W. Vs* 29143 1-33 - 1.13.4. 1.13.4.1. 1.13.4.2. 1.13.4.3. 1.13.4.4. 1.13.4.5. 1.13.4.5.1 1.13.4.5.2 113.4.5.3. 103.4.5.4. SECTION 1 MATERIAL SPECIFICATIONS Material SpeciQcaUon L13.4. Universal Primer >926 AUff. 1971 UNIVERSAL PRIMER #926 * Intended Use: As a primer over varied number of surfaces including new clean steel, or previously painted surfaces. Specifically designed for an all purpose maintenance primer. General Description: Shall be a vinyl-alkyd silica chromate high quality heavy duty corrosion resistant primer. Application Limits: Shall be suitable for application by brush or spray at temperatures down to 40 F. Colon Shall be light orange. Properties: Universal primer shall have the following properties: Properties, Wet, shall be: Flammability__________________ Storage Stability_______________ Viscosity , - ., Weight per Gallon_____________ Flash point shall not be lower than 70 F .1 year .Brush or spray (70 to 80 KU) 10.9 lbs. . 0.2 lbs. Properties, Application, shall be: Adhesion to Substrat?__________ Coverage ______________________ Drying Time__________________ Solvent________________________ Excellent .400 to 500 sq. ft per gallon .20 to 30 minutes, touch 6 to 8 hours, through .#926-T Thinner Properties, After Drying, shall be: Adhesion to Substrate ----------------- TrwoUont Construction and contractionMust conform to substrate As Substrate Base.--Suitable for common paints, PVA, and PVC overcoatings Universal primer shall be #926 universal primer as manufactured by Vimasco Coatings Corp. VIMASCO COATINGS CORP. P. O. Sac 3U, Nitre. W. V* 25143 1-35 1.1A2. 1.14.2.L 1.142.2. 1.14^3. 1.14.2.4. 1.14^.5. L14^5.1. U4Z5.2. 1.14^5.3. 1.14^5.4. U4^6. SECTION 1 MATERIAL SPECIFICATION Material Specification- 1.14.2. Fire Retardant (Intnraeseent) Coating l'.O.l*. 762-10 Aug. 1071 FIRE-RETARDANT (INTUMESCENT) COATING--P. O. F. #62-10 Intended Use: As a protective heavy build coating which when exposed to heat foams a multi-ceiled insulation which thermally insulates the substrate from the fire. This coating is to be applied in a thicker film than fire-retardant paint (P. O. F. 52-10), so as to provide greater protection (longer time) for the substrates to which it is applied. ' General Description: An intumescent coating for use on metal surfaces and insulation weather-barriers. (Ferrous metals and flammable materials require a suitable primer prior to application of the fire-retardant coating.) Shall be suitable for application by brush or spray. Shall be suitable for indoor or outdoor application but must be overcoated with fire-retardant paint 52-10 topcoat when used outdoors. Shall be factory mutual approved. Application Limits: Shall be suitable for application at ambient air temperature down to 40 F. Color: Shall be white or light tints, as specified. . Fire retardant coating shall have the following properties: Properties, Wet, shall be: Flammability --- -- Fungus Resistance______ Odor------------------------------ Storage Stability------------- Total Solids______________ Viscosity -- Weight per Gallon______ .Flash point shall be not less than 90 F .Resistant to fungus growth .Non-offensive .1 year .68 to 70% 95-100 KU ,10i lbs. m 0.2 lbs. Properties, Application, shall be: Adhesion to Substrate_________________ Consistency ----------------------------------------- Coverage which will obtain a coating of 14 irtilg - Drying Time---------------- ----------------------- Solvent------------------------------------- ----------- .Excellent - .Suitable for brush or spray application .75 sq. ft/gaL .To touch 4 hours, through--48 hours ' Aromatic Solvent (62-10T) Properties, After Drying, shall be: Abrasion Resistance____________________ Adhesion ... Elongation ------------------------------------------- Temperature limit of Substrate________ .Good '. Excellent .Will contract and expand with substrate .340 F mayimiinri Properties to Withstand Fire, When Dry, shall be: Flame Spread Index ----------- ------- Mnt over 25 Fuel Contribution Index _________________-_______ Not over 15 Smoke Density Index______________________ Not over 10 .. Fire-retardant coating of these properties shall be P. O. F. #62-10 Fire Retardant Coating as manufactured by Vimasco Corp. .. . VXUASCO COATINGS CORP. P. O. Bo* US, Nitre, W. V*, 29143 1-37*' '' 1.14.3.5.4. 1.14.3.6. Material Specification 1.14.3* Fire Retardant Varnish P.OJF. /52-7 An;. 1971 Light Stability ---------------------------- -------------------------------Good Temperature Limit of Substrate Surface-------------------------300 F Properties to Withstand Fire After Drying, shall be: When applied on Douglas Fir Flame Spread IndexShall not be over 40 Fuel Contribution IndexShall not be over 15 Smoke Density IndexShall not be over 145 Fire retardant varnish of these properties shall be P. O. F. #52-7 Parts "A" and "B" as manufactured by Vimasco Corp. VTMASCO COATINGS COBP. P. O. Bex US, Nitre, W. Va* 33143 1-39 U5X 1.15.1.1. 105X2. 1.15X3. 1.15.1.4. 1.150.5. SECTION 1 MATERIA!-. SPECIFICATION Material Specification 1.1S.1. ' Aromatic and Ketone Solvent #4$-X Aug;. 1971 : . . AROMATIC AND KETONE SOLVENT--#49-T . Intended Use: As a solvent and thinner of vinyl coating and sealer (Vicarlon #49) General Description: A 50-50 blend of Aromatic and Ketone Solvents. Shall be suitable to be used as a thinner and to clean equipment, brushes, and spillage. Color: Slightly amber Properties of Aromatic and Ketone Solvent shall be: Density, lbs, per Gallon;.................................................. ...... . Approximate 7.45 lbs. ' Flammability, liquid, Flash PointNot lower than 60 F ViscosityLight liquid Precautions ,,. ....... ...................... Keep away from sparks and open flame. Use with adequate ventila tion. Avoid prolonged breathing of vapors and contact with skin Aromatic and Ketone Solvent of these properties shall be Vicarlon #49-7 Thinner as manu factured by Vimasco Corp. , VUCASCO COATINGS CORP. P. O. Box 916, Nitre, W. Vv, SMS 1-41 , 1.15.5. 1.15.5.1. 1.15.5.2. 1.15.5.3. 1.15.5.4. 1.15.5.5. 1.15.5.6. Material Specification' 1.15.5. Aromatic and Ester Thinner i*.O.F. #52-7-T Auff. 1971 SECTION 1 MATERIAL SPECIFICATION AROMATIC AND ESTER THINNER--P.O.F. #52-7-T Intended Use: As a thinner for fire-retardant varnish (52-7 "A" "B"). General Description: An aromatic and ester solvent which is suitable for slight thinning of these varnishes without hindrance to their fire-retardant properties. Shall be the only type thinner used to clean brushes and spray equipment used to apply this fire-retardant varnish. Thinning Limits: Quantity of thinner added to 52-7 "A" or "B" shall not exceed Vz pint to a gallon. Colon Shall be clear. Properties of Aromatic and Ester Thinner shall be: Density, lbs. per gallon_________________________________ 7.6 to 7.7 lbs. goFlammability, Liquid* Flash Point_________________ ____ Not be lower than F Viscosity ---------------------------------------------------------------------- Light liquid. Precautions -------------------------------:Keep away from heat, sparks and fire. Use with adequate ventilation. Avoid prolonged breathing of vapor ' and repeated contact with skin, Aromatic and ester thinner of these properties shall be P. O. F. #52-7-T Thinner so manu factured by Yimasco Corp. * VHCASCO COATINGS CORP. P. o. Box Hf, Nitre, w V*, 23143 1-45 1.15.3. 1.15.3.1 1.15.3.2. L15.3.3. 1.15.3.4. 1.15.3.5. 1.15.3.6. SECTION 1 MATERIAL SPECIFICATION Material Specification 1.13.3. Aromatic Thinner P.OJ?. Y52-1Q-T Aus;, 1971 AROMATIC THINNER--P. O. F. #52-10-T* Intended Use: As a solvent and thinner of fire-retardant paints and coatings (P.O.F. //25-10 and P. O. F. 62-10). General Description: An aromatic solvent which gives controlled drying, leveling and flow characteristics to the paint and coating which require thinning for spraying. Thinning Limits: Quantity of thinner added to P. 0. F. #52-10 should never exceed one pint to a gallon. Color: Clear. Properties of Aromatic Thinner shall be as follows: . Density, lbs. per gallon__________________________ --..... 7,3 to 7.4 lbs. Flammability, Liquid, Flash PointNot be lower than 140 Viscosity ------------------------------------------------------------ ---------Light liquid Precautions--....... ........ . ---------------------------------Keep away from heat, sparks and flame. Use with adequate ventila tion. Avoid prolonged breathing of _ vapors and repeated contact with skin Aromatic Thinner of these properties shall be P. 0. F. #52-10-T Thinner as manufactured by Vimasco Corp. VnCASCO COATINGS CORP. P. O. Box UVKttco, W. Vt, HM3 M3 "MASCO O. Box C51O6,ANTlItNTOG,SWC.OVRsP. . 25143 August, 1971 SECTION 2 APPLICATION SPECIFICATIONS Application Spocilkalioiis--Scope Aug. 1371 1 WEATHER-BARRIER SYSTEMS, VAPOR-BARRIERS, VAPOR-SEALERS, ADHESIVES, FIRE PROTECTION SYSTEMS * INDOOR FINISHES AND OVERCOATINGS These specifications provide the application methods by which materials are used in a system to perform certain functions. These functions are (1) To serve as weather-barrier, (2) To serve as vapor-barrier, (3) To serve as a decorative and protective finish, (4) To vapor-seal insulation, (5) To adhere insulation to a surface and to itself, (6) To serve as condensation control and (7) To provide fire protection. The selection of materials, and method of application, depends upon the insulation materials used and service conditions. Because of these variables a number of application specifications are necessary for each function. ' The following Application Specifications are presented to provide engineers and contractors specifica tions of Materials, or combination of materials, and their proper application to obtain the economical installation to fulfill specific requirements. . The following listing will serve as a guide for selection. VDCASCO COATINGS COBP. P. O. Box ws. NUra. W. 2S143 2-1 Sec. Spec. No. No. Function 2. 15. Vapor-Barrier and Weather-Barrier Service Applied To Rigid and Semi-Rigid Insulation on Equipment and Pipe Application Specifications--List Aug. 1971 Mastic. Coating Page Temperature or Adhesive Sec- No. Moderate and Low Vapor-Barrier Mas- tic and Polyvinyl- Acetate Emulsion Mastir 2-36 2. 16. Vapor-Barrier and Weather-Barrier Rigid and Semi-Rigid Insula tion on Equipment and Pipe Moderate and Low Vapor-Barrier Mastic and Acrylic Emulsion Mastic _.2-40 2. 17. Vapor-Barrier and Finish Rigid and Semi-Rigid Insula- Moderate Vapor-Barrier and tion on Equipment and Pipe and Low PVA Coating_____ 2-43 2. 18. Condensation Control Equipment and Pipes Below ' Ambient PVA Cork Filled Mastic ___ .2-45 2. 19. Fire Protection Equipment, Pipe or Structural Steel HighModer-Fire Retardant ate or Low Coating___________ 2-47 2. 20. Decorative Pro- Insulated Equipment tective Over-Coating and Pipe High Moder-PVA Emulsion Paint ate or Low (Flat Surface) ____ 2-48 2. 21. Decorative and Protective Over-Coating Insulated Equipment and Pipe High Moder- Vinyl-Chloride ate or Low Paint (Semi-gloss).. 2-49 2. 22. Sealing and Vapor Barriers Figures 1 thru 28 Rigid and Semi rigid Insula tion on Walls and Ceilings of Refrigerated Spaces Low Cold Eond Adhesive 2-51 Vapor Barrier and Mastic 2-F1 to 2-F28 VZUASCO COATINGS COBP. P. O. Box 3M. Nitre, W. Vjl, 23143 2-3 2X3.2. 2X3.3. 2X3.4 2X3.5. 2X3.6. 2.1.4. 2.1.41. 2X42. 2.1.43. 2.444 2X45. 2.1.45X 2X45.2. 2X45.3. 2.1.45.30. 2.1.45.30. 2X4.5.3.3. 2.1.45.4 2X45.41. * Application Spccillcalion -.1. Aug. 1971 Where insulating cement is used over insulation block, or segments, it shall completely cover the hexagonal wire netting reinforcement and shall be troweled to an even smooth surface. Sharp outside comers of insulation shall be rounded off to a curvature of not less than one inch radius. Metal protrusions through insulation shall be insulated completely, extending a minimum distance of four times the insulation thickness. This applies to metal which is hot and is required to provide surface temperatures within limits of weather-barrier mastic. Refer to Figure 2. Insulation shall be installed so as to be properly sloped for water drainage. Insulation surfaces shall be smooth, even, clean and dry. APPLICATION OF WEATHER-BARRIER Expansion joints, flush type or flange type, shall be constructed prior to application of adjacent mastic weather-barrier. Typical examples of these expansion joints are shown in Figure No. 1. A heavy flllet of an approved heat resistant silicone sealer shall be applied around all hot metal projecting through the insulation. The insulation and the metal four inches back from this junction shall be coated and sealed, as shown in Figure No. 2. Inside comers, where two planes of insulation join, shall be caulked with'caulking and flllet compound to obtain a minimum one inch radius on.all inside comers. This is shown in Figure No. 3. Weather-barrier mastic of regular formulation shall not be applied when ambient air tem perature is below 25 F. or when temperature is expected to be below 25 F. within the next 24 hours. SPRAY APPLICATION OF MASTIC TO LARGE SURFACES: (Spray application is not recommended for application on pipe insulation where the external diameter is less than 30 inches). Prior to spray application, flanges, manholes, instruments, gauges, and other areas not in sulated and not to be sprayed shall be covered to protect them from splatter, rebound and overspray. Spray application shall be done with proper air or airless spray guns and equipment which are clean and properly adjusted to obtain a uniform diffused spray pattern. SPRAY APPLICATION OF MASTIC WITH EXTENSIBLE CLOTH REINFORCEMENT. Insulation surface shall be given a tack coat of mastic. While this coat of mastic is still wet the reinforcing cloth shall be applied and embedded into the-mastic. Cloth shall be drawn taut and smooth. All cloth joints shall be overlapped a minimum of two inches. All inside and outside comers shall be overlapped so as to cover the comers with two layers of cloth. This application is shown in Figure No. 3. * Coating and reinforcing shall extend four inches onto metal which projects through the insulation. It shall also extend four inches beyond the termination of insulation on supports, skirts, etc. Typical application is shown in Figure No. 3. After first coat has taken its set, a second coat shall be sprayed to such a thickness that when dry, the combined thickness of the first coat, the reinforcing cloth and the second coat measures 1/16 inch. Care shall be taken that second coat completely covers, fills, and seals voids in reinforcing cloth. SPRAY APPLICATION OF MASTIC WITH HEXAGONAL WIRE NETTING REINFORCEMENT. On large areas where wire netting is specified, one inch hexagonal wire nettim: shall !* installed over the insulation surface. Galvanized wire netting shall be used in ordinary VXMASCO P. O. BOX SCICO,ANTiItNreG,SWC. OVRxP..2SM3 2-5  Application Spcciiicalion 2~. Aug. 1371 SECTION 2 APPLICATION SPECIFICATION NO. 2 WEATHER-BARRIER INSTALLATION SPECIFICATIONS MODERATE AND HIGH TEMPERATURE EQUIPMENT AND PIPING (Service Temperature Above Ambient Air Temperature) INSULATED WITH RIGID INSULATION ACRYLIC EMULSION WEATHER-BARRIER MASTIC AC-7 2.2.1. 2.2.1.1. SCOPE: These specifications provide the list of essential materials and installation procedure for the application of weather-barrier of insulation on equipment and piping, located outdoors operating above ambient air temperature. The weather-barrier described in this specification is suitable for application on calcium silicate, asbestos fiber, expanded silica, cellular glass, diatomaceous earth, fibrous glass, min eral wool and expanded organic foam insulations. 2.2.2. WEATHER-BARRIER MASTIC AND ACCESSORIES REQUIRED 2.2.2.1. Weather-barrier and accessories listed shall be of type and have properties as given in desig nated section of the MATERIALS SPECIFICATION. 2.2.1. L1. Weather-barrier for troweling or palming shall be acrylic polymer emulsion type mastic as specified in MATERIAL SPECIFICATION, Section^l.2.3. (AC-7 Regular Grade). 222.12. 222X2. 2.2.2J..4. 2222.5. 9, 9 9,1 fi Weather-barrier for spray application shall be acrylic emulsion type mastic as specified in MATERIAL SPECIFICATION Section 122. (AC-7 Spray Grade). Caulking and fillet compound shall be emulsion resin, cork filled type as specified in MATERIAL SPECIFICATION Section 1.5.1. (#7G3-C). Reinforcing cloth shall be of resin fiber, extensible reinforcing cloth as specified in MATER IAL SPECIFICATION Section LIU. (#894). . Wire netting, where required, shall be as specified in MATERIALS SPECIFICATION Section 1.11.5. Heat resistant sealer shall be as specified in MATERIALS SPECIFICATIONS Section 1.4.3. 222. APPLICATION OF EQUIPMENT AND PIPING INSULATION 2.22.1. The following is given to provide the essentials of insulation application as related to the proper function of the weather-barrier system. The type of insulation, its required thickness and details of its installation are beyond the scope of this specification. Insulation on equipment and piping shall be supported and secured in such a manner that the insulation joints are drawn tight and flush. If at all possible, the insulation shall be in stalled so that the movement of the equipment, or pipe, due to expansion is not transmitted to the insulation except at the insulation expansion joints. . 2222. Where insulating cement is used over insulation block or segments it shall completely cover the hexagonal wire netting reinforcement and be troweled to an even smooth surface. 2.2.3.3. Sharp outside corners of insulation shall be rounded off, to a curvature of not less than one inch radius. 222.4. Metal protrusions through insulation shall be insulated completely, extending a minimum distance of four times the insulation thickness. This applies to metal which is hot and is re quired to provide surface temperatures within limits of weather-barrier mastic. Refer to Figure 2. 2222. Insulation shall be installed to be properly sloped for water drainage. 2.2.3.6. Insulation surfaces shall be smooth, even, clean end relatively dry. VTMASCO P. O. Bos SCICO.ANTiItNreG,SWC. OVR*P,. 29143 2-7 2.2A5.5. 2.2A6. 2.2.4.6.I. 2J2.4.6.2. 2J2.4.6.3. 2.2.4.S.4. 2.2A6.5. *; 2X4.6.6. 2.2A6.7. 2JL4.6.8. Application Spcrilicaliou 22. Au?. 1971 and laced together with 22 gauge stainless steel wire. The mastic shall be sprayed on surface to full thickness in one coat, in such manner as to completely cover the cloth. (Pressure of spray will force mastic around and back of cloth wire. Note: The pattern of reinforcing cloth or netting wire will show on the outer surface regard less of the thickness of the mastic. Drip, splatter, or rebound mastic on floors or other areas not insulated must be cleaned up with water before mastic sets. TROWELED OF PALMED APPLICATION On flat, double curved, large cylindrical, and irregular insulation surfaces a tack coat shall be troweled or palmed onto the insulation. While this coat of mastic is still wet, the reinforcing cloth shall be applied and embedded into the mastic. All cloth joints shall be overlapped a minimum ox two inches. On straight piping the cloth may be installed by using just sufficient mastic to bond the cloth end to the pipe insulation, then it shall be spiral wrapped around the cylindrical pipe insulation. Termination end of roll shall be adhered with mastic, to the insulation. The beginning of next roll shall overlap end of first and *be adhered with mastic. Cloth appli cation shall then be continued over the insulated straight pipe. All cloth joints shall be overlapped a minimum of two inches. All fitting and valve insulation covers shall be given attack coat of mastic, and then the rein forcing cloth shall be applied as called for in 2.2.4.5.I. All inside and outside corners, where two planes of insulation meet, shall be overlapped so as to be covered with two layers of cloth, as shown in Figure No. 3. Coating and reinforcing cloth shall extend out four inches onto metal which projects through the insulation. It shall also extend four inches beyond the termination of insulation on supports, skirts, etc. Typical application shown in Figure.No. 3. After first coat of mastic, used to bond spiral \vrapped cloth, has taken its set, a final coat of weather-barrier mastic shall be troweled or palmed over the entire reinfo cing cloth surface. This mastic shall be pressed so it penetrates the weave of the cloth so as to obtain a good bond with the first coat (or the insulation) surface. Care shall be taken that this coat completely covers, fills, and seals voids in reinforcing cloth. After mastic has dried, the combined thickness of mastic and cloth should measure not less than 1/16 inch. Note: The pattern of the reinforcing cloth or netting will show on the outer surface, regard less of the thickness of the mastic. Where a smooth finish is desired, the final coat shall be "water brushed*' before it takes its set Care shall be taken that just a sufficient amount of water is used to smooth the surface without diluting the body of the mastic. Spills, drips or splatter of mastic on floors or other areas not insulated shall be cleaned up with water before mastic sets. VZMASCO COATINGS COKP. P. o. Sox 91, Nttro, W. Va* 29143 2-9 2.3.3A 2.3.3.S. 2.3.4. 2.3.4.1. 2.3.4.2. 2.3A3. 2.3.4.4. 2.3.4.5. 2.3.4.3.1. 2J3.4.5.2. Z3.4.5J3. 2.3.4.5.4. 2.3.4.5.5. 2.3.4.B. 2.3.4.6.1. 2.3A6.2. 2.3.4.6.3. 2.3.4.6A Application ^puciileulioa 2JZ. All?. 1071 reauired to provide surface temperature within limits of weather-barrier mastic. Refer to Figure 2. Sharp outside corners of insulation shall be rounded off to a curvature of not less than one inch radius. ' Insulation surfaces shall be smooth, even, clean and dry. APPLICATION OF COATING FINISH Expansion joints, flush type or flange type, shall be constructed prior to application of adjacent mastic finish. Typical examples of these expansion joints are shown in Figure No. 1. A heavy fillet of insulating-finishing cement tapered to hot surface shall be applied around all hot metal projecting through the insulation. This cement shall be applied and allowed to dry prior to application of mastic finish. This is shown in Figure No. 4. Inside comers, where two planes of insulation join, shall be caulked with caulking and fillet compound to obtain a minimum one inch radius on all inside corners. This is shown in Figure No. 3. Finish mastic shall not be applied when ambient air temperature is below 40 F or when tem perature might be lower than 32 F in the following 24 hours. SPRAY APPLICATION OF COATING FINISH TO LARGE SURFACES: (Spray application is not to be used for application of-finish mastic to piping insulation). Prior to spray application, flanges, manholes, instruments, gauges, floors, ceiling and walls shall be covered or shielded to protect them from splatter, rebound, and overspray. Spray application shall be done with proper air or airless spray guns and equipment which are clean and properly adjusted to obtain a uniformly diffused spray pattern. Insulation surface shall be given a tack coat. While this coat is still wet the cloth shall be applied and embedded into the coating. Cloth shall be drawn taut and smooth. All joints shall be overlapped a minimum of two inches. After first coat has taken its set, a second coat shall be applied to completely cover the cloth. Where a smooth finish is desired the surface shall be water brushed before it sets, using just sufficient quantity of water to smooth the surface without softening the body of the coating. Drip, splatter, or rebound coating on surfaces not to be finished with the mastic shall be cleaned up with water before the mastic sets. PALMED OR BRUSHED ON APPLICATION: A tack coat shall be palmed or brushed onto the insulation surface. While this coat is still wet the cloth shall be applied -and embedded into the coating. Joints of cloth shall be over lapped a minimum of two inches with lap of top cloth securely bonded to cloth beneath with the finish coating. After the tack coat has taken its set, a second coat shall be applied to completely cover the cloth. ' Where an exceptionally smooth finish is desired, the fin?! coat sh?lt be "water brushed" be fore it takes its final set Care shall be taken that just sufficient amount of water is used to smooth the surface without diluting the body of the coating. Spills, drips, or splatter of coating on surfaces not to be finished shall be cleaned up with water before the coating sets. VIUASCO COATINGS CORP. P. Q. Sox 916, Nttro. W. 23143 Ml. 2.4.3.3. 2.43.4 2.4.4. 2.44.1. 2.4.4X 2.44.3. AppUcuUou S usvificulion JJ.4. . Aug. L!>71 Metal protrusions through insulation shall be insulated completely, extending a minimum distance oil four times the insulation thickness. This applies to metal which is hot and is required to provide surface temperatures within limits of the weather-barrier coating. Refer to Figure 4. . Insulation surfaces shall be smooth, even, clean and dry. APPLICATION AND FINISH OF CLOTH OYER INSULATION Expansion joints, flush type or flanged fitting type, shall be constructed prior to applica tion of cloth. Typical examples of these expansion joints are shown in Figure No. 1. Inside corners where planes of insulation join shall be caulked with caulking and fillet com pound or insulating-finishing cement to obtain a minimum one inch radius or all inside corners. This is shown in Figure No. 3. Application of cloth by adhesive or application of sizing coat shall not be done when ambient temperature is less than 40 F. 2.445. 2.4.45.1. 2.445.2. 2.445.3. 2:4.45.4. 2.445.5. 2.445.6. 2.445.7. SFRAY APPLICATION OF ADHESIVE-COATING FOR CLOTH ATTACHMENT AND FINISH. Prior to spray application, flanges, manholes, instruments, gauges, floors, ceiling and walls should be covered or shielded to protect them from splatter, rebound and pverspray Spray application shall be done with air or airless spray guns and equipment which are clean and properly adjusted to obtain a uniformly diffused spray pattern. Ad hesive-coatings specified in MATERIAL SPECIFICATION, Sections 1.3.L (#136) and 1.3.2. (#713) are suitable for spray application. The proper one of these, as specified, shall be used. Insulation shall be given a tack coat of adhesive-coating. While this coat is still wet the specified doth shall be embedded into the adhesive. Cloth shall be drawn taut and smooth. All joints shall be lapped a minimum of one inch. Adhesive coating shall be applied between the layers of cloth at laps to obtain a tight lap bond. Flammable cloths shall be cut back at least two inches from all hot projections. Adhesive coating shall be applied over insulation up to the hot projection. After tack coat of adhesive-coating has taken its set a finish coat shall be spray applied over the doth. Drip, splatter, or rebound adhesive-coating on surfaces not to be finished shall be cleaned up with water before the material sets. 2.446. 2.446.1. 2.446.2. 2.446.3. 2.446.4 BRUSH APPLICATION OF ADHESIVE-COATING FOR ATTACHMENT AND FINISH OF CLOTH. Adhesive-coating as called for in MATERIAL SPECIFICATION, Sections 1.3.1. (#136) or 1.3.2. (#713), whichever is specified shall be used. * Oh concealed piping suffldent area of insulation be covered with adhesive-coating to hold doth in position. Cloth shall be applied and drawn taut and smooth. All joints shall be lapped a minimum of one inch. Adhesive shall be applied between layers of cloth at laps to obtain a tight lap bond. On exposed piping and equipment entire insulated area shall be given a tack coat of adhesive coating. While this coat is still wet the specified doth shall be embedded into this adhesive. Cloth shall be drawn taut and smooth. All joints shall be lapped a minimum of one inch. Ad hesive-coating shall be applied between the layers of cloth at laps to obtain a tighv lap bond. Flammable doths shall be cut back at least two inches from all hot projections. Adhesive coating shall be applied over the insulation up to the hot projection. * VIMASCO COATINGS CORP. P. O. Box SIC, Nltro, W. Va^ 23143 2-13 2.5.1. 2.5.1.1. 2.5.2. 2.5.2.1. 2.5.U. 2.5.3. 2.5.3.L 2.5.3.2. 5.3.3. 2.5.3J3.1. 2.5.3.3.2. 2.5.3.4. 2.5.3.4.I. 2.S.3.5. 2.5.3.5.I. 2.S.3.5.2. 2.5.3.5.3. 2.5.3.5.4. SECTION 2 APPLICATION SPECIFICATION NO. 5 Application Specification Aujf. 1971 DUCT LINING--FLEXIBLE INSULATION INSTALLATION AIK CONDITIONING AND HEATING DUCTS THERMAL AND ACOUSTICAL INSULATION LININGS RUBBER INSULATION ADHESIVE DUCT AND LAP ADHESIVE-CLEAR AMBER VIMASCO #730 SCOPE: These specifications provide the list of essential materials and accessories required to install "flexible" fibrous glass insulation to the interior surfaces of air conditioning and heating ducts. The adhesive -coating called for in this specification shall be suitable for securing flexible fibrous glass to the interior of air conditioning and heating ducts. After drying, the adhesive shall have a flame spread index of less than 25, and be in accordance with Interim Federal Standard 00136b so as to meet with federal, state and local codes. RUBBER INSULATION ADHESIVE AND ACCESSORIES REQUIRED. The rubber insulation adhesive shall fulfill installation requirements and have sufficient "open time" so that large areas of insulation can be installed before the adhesive takes its set. Adhesive shall have the properties as specified in MATERIAL SPECIFICATIONS, Sec tion 1.7.1. (#730). _ Where required, due to high air velocity in the duct, insulation shall be additionally secured to the metal by grip nails or Welding pins and pin clips. INSTALLATION OF INSULATION LINING. Installation depends upon velocity of air in duct ' Insulation selected shall be suitable for the velocity of air in duct; however, selection of the insulation, its density, and its thickness, are beyond the scope of this specification. APPLICATION OF INSULATION FOR DUCTS WITH AIR FLOW VELOCITIES UP TO 1500 FM. Apply adhesive by spray or brush in equally spaced stripes so as to cover at least 50% of the metal surface, at a rate of 200 sq. ft per gallon. While adhesive is still wet, insulation shall be pressed firmly to the metal surface. When width of duct exceeds 12" and the height exceeds 24" additional sccurement of grip nails, or welding pins and fasteners shall be installed at center line of sides and top on 16" centers. When the width or height exceeds 32" these securements shall be on 16" centers, staggered. '" APPLICATION OF INSULATION FOR DUCTS WITH AIR FLOW VELOCITIES 1500 to 4000 FM. Application shall be same as for 2.5.3.3. except that a heavy coat of adhesive shall be applied from the leading edge of each panel of insulation back 6" to obtain complete bond of the insiilatirm- APPLICATION OF INSULATION FOR DUCTS WITH AIR FLOW VELOCITIES 4000 to 0000 FM. Apply adhesive by spray or brush over 100% of the metal surface, at a rate of 200 sq. ft per gallon. While adhesive is still wet, insulation shall be pressed firmly to metal surface. Securements of grip nails or welding pins and fasteners shall be installed on a maximum of 16" centers staggered as per 2.5.3.3A All edges of flexible insulation shall be given a heavy coat of adhesive. Typical installation is shown in Figure No. 5. * VIMASCO COATINGS CORP. P. O. Boat 51*. Nttro, W. V, 29143 2-15 2.G.3.4.3. 2.6.3.4A 2.6.S.5. 2.S.3.6. Coated side of insulation shall face the air How. Application Spucilicalioa i.6. Aus. 1971 Insulation joints and edges shall be caulked and coated with the fire resistive adhesive. Where required to reduce friction loss and to increase the attenuation of low-frequency fan noise th^ entire exposed surface of the insulation hll be given a brush coat of fin-retardant polyvinyl-acetate emulsion lagging adhesive as specified in MATERIAL SPECIFICATIONS, Section 1.3.L (#136) Typical application is shown in Figure No. 6. * i VXKASCO COATINGS CORP. P. O. Bos Sl, Nttro, W. VA* 23143 2-1? 2.7.4.C. 2.7.5. 2.7.5.1. 2.7.5.2. 2.7.6. 2.7.6. L Typical installation is shown in Figure No. 7. Application Specification 2.7. Aug. 1071 OVERCOATING: Where exposed to view, and painted color surface is required, the jacket shall be painted with two coats of polyvinyl-acetate emulsion paint as specified in MATERIAL SPECIFICA TIONS, Section U2X (Liquid Vinyl PVA). Application of paint shall be as specified in APPLICATION SPECIFICATION No. 21. WEATHER PROTECTION: Insulated duct, exposed to weather, shall have a mastic weather-barrier installed over the insulation, or the jacketed insulation, in accordance with APPLICATION SPECIFICATIONS No's. 1 or 2. PVI.MoA.SBCOOX SCICO.ANTiItNreG,SwC. OVR*F,.29143 2-19 2.5.4.4. 2.5.4.6. 2.5.4.7. 2.8.4.5. 2.8.5. 2.8.5. X. 2.8.5.1.1. 2.8.5.1J2. 2.8.5.X.3. 2.8.5^. 2.8.5.2.1. XS.5XZ. 2.8.5^3. 2.8.6. 2.8.6.1. 2.3.6.2. 2^.7. 2.8.7. L Apjiiicntiou SpcciUcutiou Auj;. 1971 Fitted insulation shall be pressed firmly into the wet adhesive and temporarily held in posi tion until adhesive has taken its set. Where pins are required for securement the speed nuts shall be pressed to depress insulation sufficiently, that pin can be cut 1/16 inch' below insulation surface. This depression shall be filled with fire-resistant caulking mastic flush with adjacent surface. Caulking shall be as specified in MATERIAL SPECIFICATION 1.5.1. All cracks or slightly open joints shall be caulked with fire-resistive caulking mastic. (Same as above). Over each caulked mechanical fastener a 4 inch by 4 inch square patch of tape shall be sealed and bonded with adhesive to the surrounding jacket surface. APPLICATION OF VAPOR-BARRIER JACKET OR OUTER COVERING: Vapor-barrier jacket shall be installed over all insulation installed on ducts which operate below ambient temperature. Vapor-barrier lap flanges shall be sealed and bonded to adjacent jacket with adhesive applied by brush at a rate of approximately 80 sq. ft per gallon. Where jacket lap flanges are not supplied on insulation to cover joints and at joints of fitted pieces, the jacket shall be coated slightly more than two inches on both4 sides of the butt joint with adhesive. The four inch wide joint tape shall be pressed firmly into the adhesive to obtain bond and sealing of the insulation jacket - Typical installation is shown in Figure No's 8 and 9. Outer coating or covering on ducts operating above ambient air temperature shall be as selected in accordance with location and installation requirements. Ducts operating above ambient air temperature, concealed from view and not subjected to mechanical abuses require no covering. Where specified, ducts operating above ambient nir temperature shall be jacketed as called for installed in accordance of 2.8.5.L of this specification. Where exposed to view, and so specified, ducts shall be covered with Vinyl-Acetate Lagging Adhesive and Coating and Cloth as specified in APPLICATION SPECIFICATIONS NO. 4. OVERCOATING Where ducts are exposed to view and painted surface is required, the jacket or sized cloth shall be painted with two. coats of polyvinyl-acetate emulsion paint as specified in MATER IAL SPECIFICATIONS, Section 1.12.1. (Liquid Vinyl PVA). Application of paint shall be as specified in APPLICATION SPECIFICATIONS NO. 2L WEATHER PROTECTION: . Insulated duct, exposed to weather, shall have a mastic weather-barrier installed over the insulation, or the jacketed insulation, in accordance with APPLICATION SPECIFICATIONS NO'S. 1 or 2. VIMASCO COATINGS COUP. P. O. Bax SIS. Nttro, W. Va, 29143 2-21 2.9.3.I. 9.3.2. Application Spccitieatioa 2.1). Aug:. 1971 Insulation shall be supported, secured and installed in such manner that it provides a firm and smooth base tor the application of the mastic and its reinforcement Insulation over ribs or projections shall be rounded off over outside comers and installed with a minimum 1" radius on inside corners. This installation is shown in Figure No. 18. 2.9.4. 2.9.41. 2.9.42. APPLICATION OF WEATHER-BARRIER. A heavy fillet of best resistant silicone sealer shall be applied around all hot metal project ing through the insulation. The insulation and <he metal four inches back from this junction shall be coated and sealed as shown in Figure No. 19. Weather-barrier polyvinyl-acetate emulsion mastic shall not be applied when ambient air temperature is below 25 F or expected to be below 25 F within the next 24 hours. Mastic must not be applied on sprayed insulation until the insulation has taken its set and is essentially dry. 2.9.4.3. 9.43.1. 2.9A3.2. SPRAY APPLICATION OF MASTIC. Prior to application, flanges, manholes, instruments, gauges, and other areas not insulated and not to be sprayed shall be covered to protect them from splatter, rebound and overspray. Spray application shall be done with proper air or airless spray guns and equipment which are dean and properly adjusted. * 2.9.43X 2.9.43.3.1. 9.43.3.2. 2J.43^3. SPRAY APPLICATION OF MASTIC WITH EXTENSIBLE CLOTH REINFORCEMENT. Insulation surface shall be given a tack coat of mastic. While this coat of mastic is still wet the reinforcing doth shall be embedded into the mastic. Cloth shall be drawn taut and smooth. All doth joints shall be overlapped a minimum of two inches. All inside and out side comers shall be overlapped so as to cover the comers with two layers of doth. This application is shown in Figure No. 3. ' Coating and reinforcement shall extend four inches onto metal which projects through insu lation. It shall also extend four inches beyond the termination of insulation on supports, skirts, etc. Typical application is shown in Figure No. 3. After first coat has taken its set, a second coat shall be sprayed to such a thickness that when dry, the combined thickness of the first coat, the reinforcing doth, and the second coat measures 1/16 inch. Care must be taken that th^ second coat completely covers, and seals voids in reinforcing doth. 2.9.43.4 9.43.44 2.9.43.42. 2.9.43.43. 2.9.43.44 2.9.43.45. SPRAY APPLICATION. OF MASTIC WITH HEXAGONAL WIRE NETTING REINFORCEMENT. Hexagonal wire netting shall be used only where it is possible to draw it taut and flush to the insulation surface. Galvanized wire netting shall be used in ordinary atmospheres, whereas monel wire netting shall be used in areas of extreme corrosion. The netting shall be drawn taut and flush to the surface. Where necessary it shall be secured to pins with speed dips as shown in Figure No. 16. After clips have been applied, pin is cut off below the insulation surface. The depression $hlt be pointed up with the fibrous in sulation. Installation is as shown in Figures No. 16 and 17. Hexagonal wire netting shall be installed to fit tightly over outside and tightly into inside comers, as shown in Figure No; 18. . The mastic shall be sprayed onto the surface to the full thickness hi one coat, in such manner as to completely cover the netting and so that dried thickness is not less th^ 1/16 inch. (Pres sure of spray will force mastic around and back of netting wire.) VIMASCO COATINGS CORP. P. O. Bex Sit. Nltro. W. Va, 25143 2-23 * 2.10.1. 2.10.1.1. SECTION 2 application SPECIFICATION NO. 10 Aiu>iic:Uiou >i>cdllcalion 2.10. Aug. 1971 WEATHER-BARRIER INSTALLATION SPECIFICATIONS HIGH TEMPERATURE EQUIPMENT INSULATED WITH SPRAYED ASBESTOS OR MINERAL FIBER ACRYLIC EMULSION WEATHER-BARRIER MASTIC AC-7 SCOPE: These specifications provide the list of essential materials and installation procecedures for the application of weather-barrier o'^er insulation on equipment, located indoors or outdoors, operating above ambient air temperature. The weather-barrier described in this specification is suitable for application over asbestos or mineral fiber insulation which has been sprayed on the substrate surface and then consoli dated and compressed to required density and thickness. * . ' 2.10.2. 2.10.2.1. 2.10.2.1.1. 2.10.2.2. 2.10.2.3. 2,10.2.4. WEATHER-BARRIER MASTIC AND ACCESSORIES REQUIRED. Weather-barrier and accessories listed shall be of type, and have properties, as given in designated section of the MATERIALS SPECIFICATION. Weather-barrier shall be acrylic emulsion type mastic for troweling or `palming (Trowel Grade) suitable for installation at atmospheric temperature down to 20 F, as specified in MATERIALS SPECIFICATION, Section 1.2.4. (AC-7). Hexagonal wire mesh, where used in corrosive atmospheres shall be stainless steel or monel as specified in MATERIALS SPECIFICATION, Section 1.11.5.1. In ordinary services, shall be galvanized steel as specified in MATERIALS SPECIFICATION, Section 1.11.5.2. Lacing wire shall be as specified in MATERIALS SPECIFICATION, Section 1.11.6. Reinforcing cloth shall be extensible open weave cloth- as specified in MATERIALS SPECIFICATION, Section 1.11.1. (#894) 2.10.3. 2.10.3.1. 2.10.3.2. APPLICATION OF INSULATION. The following is given to provide the essentials of insulation as related to the proper func tion of the finish system. The type of sprayed insulation, its required thickness, and other details of its installation are beyond the scope of this specification. Insulation shall be supported, secured and installed in such manner that it provides a firm and smooth base for the application of the mastic and its reinforcing. Insulation over ribs or projections shall be rounded oft over outside corners and installed with a minimum 1" radius on inside corners. This installation is shown in Figure No. 18. 2.10.4. 2.10.4.1. 2.10.4.2. APPLICATION OF WEATHER-BARRIER. A heavy fillet of heat-resistant silicone sealer shall be applied around all hot metal projecting through the insulation. The insulation and the metal four inches back from this junction shall be coated and sealed as shown in Figure No. 19. Weather-barrier acrylic emulsion mastic shall not be applied when ambient air temperature is below 20 F or expected to be below 20 F within the next 24 hours. Mastic must not be applied to sprayed insulation until the insulation has taken its set and is essentially dry. ^ 2.10.4.3. r -2.10.4.3.1. TROWEL OR PALM APPLICATION OF MASTIC Insulation surface shall be given a tack coat of mastic by trowel or palrm While this coat of mastic is still wet the reinforcing cloth shall be embedded into the mastic. All cloth joints VIMASCO COATINGS CORP. P. O. Bx Sit, Nitre, W. V, 25143 2-25 2.11.1. 2.11.2. SECTION 2 APPLICATION SPECIFICATION NO. 11 Application Specification 2J.I. Aug. 1971 SEALING AND WEATHER-BARRIER INSTALLATION SPECIFICATIONS LOW TEMPERATURE EQUIPMENT AND PIPING INSULATED WITH CELLULAR GLASS POLYVINYL-ACETATE EMULSION WEATHER-BARRIER MASTIC WC-1, WC-1FR SCOPE: These specifications provide the list of essential sealers, anti-abrasive coatings, caulkings and weather-barriers and installation procedure for their application with the insulation on equipment and piping, located outdoors, operating at temperatures down to minus 400 F. WEATHER-BARRIER MASTIC AND ACCESSORIES REQUIRED: 2.11X1. The polyvinyl-acetate heavy build weather-barrier mastic shall fulfill the application, at mospheric and service requirements. Weather-barrier and accessories listed shall be of the type, and have the properties, as given in the designated section of the MATERIALS SPECIFICATION. . . 2.11X2.1. 2.11.2.2.1.1. Weather-barrier mastic shall be one of the following polyvinyl-acetate emulsion types: Polyvinyl-acetate emulsion type mastic for application by troweling or palming suitable for installation at atmospheric temperature down to 25 F, as specified in MATERIAL SPECI FICATION, Section 1.2.1. (WC-1 Regular Grade). 2.11.2X1.2. Polyvinyl-acetate emulsion type mastic for application by spraying (Spray Grade) suitable for installation at atmospheric temperature down to 35 F, as specified in A'-'ATFRTAT. SPECIFICATION, Section 1.2.1. (WC-1 Spray Grade). 2.11.2.2.1.3. Polyvinyl-acetate emulsion type mastic for application by troweling or palming, suitable for installation at atmospheric temperature down to 40 F. Shall be suitable for very hazardous service where surface flame spread must be kept to a minimum, as specified in MATERIAL SPECIFICATION, Section 1X2. (WC-1 FR Regular Grade). 2.11.2.2.1.4. Polyvinyl acetate emulsion type mastic for applicition by spraying, suitable for installation at atmospheric temperature down to 40 F. Shall be suitable for very hazardous service where flame spread must be kept to a minimum, as specified in MATERIALS SPECIFI CATION, Section 1.2.2. (WC-1 FR Spray Grade). 2.1L2.3. Caulking and fillet compound shall be emulsion resin, cork filled, type as specified in MA TERIALS SPECIFICATION, Section 1.5.1. (#703-C). 2.1L2.4. Low temperature butt joint sealer shall be one of the following: 2.11.2.4.1. For application where weather-barrier mastic is colored black or dark gray, the low tem perature butt sealer shall by vinyl-asphalt mastic as specified in MATERIALS SECTION, Section 1A2. (#49). 2.11.2.4.2. For application where no bleeding of sealer can be tolerated, low temperature staler shall be cold bond sealer as specified in MATERIALS SPECIFICATION, Section 1.4.L (#750). 2.11.2.5. The anti-abrasive coating shall be one of the following depending upon metal of equipment or pipe on which insulation system is being installed. 2.11.2.5.1. If metal of equipment or pipe is steel, aluminum, monel or copper, the anti-abrasive coating shall be a vinyl-chloride base solvent coating as specified in MATERIALS SPECIFICATION, Section 1.6.L (#500). ' VXMASCO COATINGS CORP. P. o. Sox 918, Nitre, W. Vft 29143 2-27 * t 2.11.6.2. 2.11.6.3. 2.11.6.4. Application Spccilicalion 2.11. Aug. 1971 Inside corners, where two planes of insulation join, shall be caulked with caulking and fillet compound to obtain a minimum one-inch radius on all inside corners. This is shown in Figure No. 3. Weather-barrier mastic shall not be applied when ambient air temperature is lower than the recommended minimum installation temperature. Proper grade--trowel or spray--shall be used as required by application method. SPRAY APPLICATION OF HEAVY BUILD WEATHER-BARRIER MASTIC TO LARGE SURFACES: , (Spray application is not recommended for application of weather-barrier to surfaces less than 30" in diameter.) 2.11.6.4.1. Prior to spray application, instruments, gauges and other areas not insulated and not to be sprayed, shall be covered to protect them from splatter, rebound and overspray. 2.11.6.4.2. Spray application of spray grade mastic shall be done with proper air, or airless, spray guns and equipment which are clean and properly adjusted to obtain a uniformly diff.ised spray pattern. 2.11.6.4.3. Cellular glass outer surface shall be given a tack coat of weather-barrier mastic. While this coat is still wet the reinforcing cloth shall be applied and embedded into this mastic. Cloth shall be drawn taut and smooth. All cloth joints shall be overlapped a minimum of two inches. All inside and outside corners, where two planes of insulation meet, shall be overlapped so as to cover the comers with two layers of cloth. This application L shown in Figure No. 3. 2.11.6.4.4. iL6.4.5. Coating and reinforcement shall extend four inches onto metal which projects through the in sulation. It shall extend four inches beyond the termination of insulation on supports, skirts, etc. Typical application is shown in Figure No. 3. After first coat has taken its set, a second coat shall be spray applied to such a thickness that when dry the combined thickness of first coat, reinforcing cloth and second coat measures 1/16 inch. Care shall be taken that second coat completely covers, fills and seals voids in the reinforcing cloth. Note: The weave pattern of the "extensible" cloth is such that it will show on the surface, regardless of thirlraggg of second coat. 2.11.6.4.6. Drip, splatter, or rebound mastic on floors and other areas not insulated shall be cleaned up with water before mastic sets. 2.11.6.5. 2.11.6.5.1. 2.11.6.5.2. 2.11.6.5.3. TROWELED OR PALMED APPLICATION OF WEATHER-BARRIER MASTIC: On flat, double curved, large cylindrical and irregular surfaces a tack coat of mastic shall be palmed or troweled onto the outer surface of cellular glass insulation. While this coat of mastic is still wet the reinforcing cloth haii be applied and embedded into the mastic. Cloth shall be drawn taut and smooth. All inside and outside corners, where two planes of insula tion meet shall be overlapped so as to cover the corners with two layers of cloth. This ap plication is shown in Figure No. 3. . On straight pipe insulation the cloth may be installed by using just sufficient mastic to bond the cloth end to the pipe insulation and then spiral wrapping the cloth around the pipe in sulation. Termination of the roll of cloth shall be mastic adhered to the insulation. The beginning of the next roll shall overlap the end of the first and be adhered with mastic. Cloth application shall then be continued over the straight pipe insulation. All cloth joints shall be overlapped a minimum of two inches. All fitting and valve insulation covers gbaii be given a tack coat of mastic and the cloth shall be applied as called for in 2.11.6.5.1. VIMASCO COATINGS CORP. P. O. Boat SIfl, Nitre. W. Va,, 23142 2-29 SECTION 2 application SPECIFICATION NO. 12 Apiiiimitoii Sncciliculiou ZSZ. Aug:. 1071 SEALING AND WEATHER-BARRIER INSTALLATION SPECIFICATIONS LOW TEMPERATURE EQUIPMENT AND PIPING INSULATED WITH CELLULAR GLASS ACRYLIC HEAVY BUILD WEATHER BARRIER MASTIC VEVCASCO AC-T 2.12.1. SCOPE: These specifications provide the list of essential sealers, anti-abrasive coatings, caulkings and weather-barrier and installation procedure for their application with the insulation on equipment and piping, located outdoors, operating at temperatures down to minus 400 F. 2.12.2. 2.12.2.1. WEATHER-BARRIER MASTIC AND ACCESSORIES REQUIRED: Weather-barrier and accessories listed shall be of the type, and have properties, as given in designated section of the MATERIALS SPECIFICATION. 2.12.2.2.1. Weather-barrier shall be acrylic polymer emulsion type mastic as required by application. 2.12^2.1.1. Acrylic polymer emulsion type mastic suitable for application by troweling or palming (AC-7 Regular Grade), suitable for installation at atmospheric temperature down to 30 F. As specified in MATERIALS SPECIFICATION, Section 1.2.3. ' . . . . . .2 12 2 2 1 2 Acrylic polymer emulsion type mastic suitable for application by spray (AC-7 Spray Grade) shall be as specified in Section 1.2.3. 2.12^.3. Caulking and fillet compound shall be emulsion resin, cork filled type, as specified in MA TERIALS SPECIFICATION, Section 1.5.1. (#703-C) . 2.12.2.4. Anti-abrasive coating shall be one of the following depending upon metal of equipment or pipe on which the insulation system is being installed. 2.12^.41. If metal of equipment or pipe is steel, aluminum, monel, or copper the anti-abrasive coating shall be vinyl-base anti-abrasive coating as specified in MATERIALS SPECIFICATION, Sec tion 1.6.1. (#500). 2.12.2.4.2. If metal of equipment or pipe is stainless steel the anti-abrasive coating shall be i product designed for this purpose. 2.12.2.5. 2.12.2.5.1. 2.12.2.5.2. 2.12.2.6. Low temperature joint sealer shall be one of the following: For brush application and where weather-barrier mastic is colored black or dark gray, the low temperature sealer shall be vinyl-asphalt sealer as specified in MATERIALS SPECIFI CATION, Section 1.4.2. (#49). For trowel application, and where no bleeding of sealer can be tolerated, low temperature sealer shall be cold bond sealer as specified in MATERIALS SPECIFICATION, Section 1.4.1. (#750) Reinforcing cloth shall be of resin fiber, extensible reinforcing cloth as specified in MA TERIALS SPECIFICATION, Section 1.11.1. . 2.12.3. 2.12.3.1. APPLICATION OF EQUIPMENT AND PIPING INSULATION: The following is given to provide the essentials of insulation application as related to the proper function of the vapor-seal and weather-barrier system. The required thickness of cellular glass, details for its support, number of layers and method of its securement are beyond the scope of this specification. . The insulation should be supported and secured so that all joints are drawn tight and flush. If at all possible, the cellular glass shall be installed so that movement of the vessel, or pipe, due to contraction is not transmitted to the insulation, except at insulation contraction joints. VtMASCO COATXNCS COUP. P. O. Sox 915. intro. W. V*^ 23143 2-31 * 2.12.6.4.3. Application Spcciiication 2.12. Augr. 1971 SPRAY APPLICATION OF MASTIC WITH EXTENSIBLE CLOTII REINFORCEMENT. '2.12.6.4.3.1. Insulation surface shall be given a tack coat of mastic. While this coat of mastic is still wet the reinforcing cloth shall be applied j and embedded into the mastic. Cloth shall be drawn taut and smooth. All cloth joints shall be overlapped a minimum of two inches. All inside and outside comers shall be overlapped so as to cover the corners with two layers of cloth. This application is shown in Figure No. 3. 2.12.6.4.3.2. Coating and reinforcing shall extend four inches onto metal which projects through the insulation. It shall also extend four inches beyond the termination on supports, etc. Typical application is shown in Figure No. 3. 2.12.6.4.3.3. After first coat has token its set, a second coat .-shall be sprayed to such a thickness that when dry, the combined thickness of the first coat, the reinforcing cloth and the second coat measures 1/16 inch. Care must be taken that second coat completely covers fills, and seals voids in reinforcing cloth. . 2.12.6.5. 2.12.6.5.1. 2.12.6.5.2. 2.12.6.5.3. 2.12.6.5.4. 2.12.6.5.5. 2.12.6.5.6. 2.12.6.5.7. TROWELED OR PALMED APPLICATION OF WEATHER-BARRIER MASTIC. On fiat, double curved, large cylindrical and irregular insulated surfaces a tack coat of mastic shall be palmed or troweled, onto .the cellular glass insulation. While this coat of mastic is still wet, the reinforcing cloth shall be applied and embedded into the wet mastic. All cloth joints shall be overlapped a minimum of two inches. * On straight pipe insulation the cloth may be installed by using just sufficient mastic to bond the cloth and to the pipe insulation and by then spiral-wrapping the cloth around the pipe insulation. Termination end of the roll of cloth shall be mastic adhered to the insulation. The beginning of the next roll shall overlap the end of the first and be adhered with Mastic. Cloth application shall then be continued over the straight pipe insulation. All cloth joints shall be overlapped a minimum of two inches. All fitting and valve insulation covers shall be given a tack coat of mastic followed by re inforcing cloth installed as called for in 2.12.6.5.L - All inside and outside comers shall be overlapped so as to be covered with two layers of cloth as shown in Figure No. 3. Coating and reinforcing cloth shall extend out four inches onto metal which projects through the insulation. It shall also extend four inches beyond the termination of insulation on supports, legs, skirts, etc. Typical application is shown in Figure No. 3. After the first coat, or mastic used to bond spiral-wrapped doth, has taken its set a final coat of weather-barrier mastic shall be troweled or palmed over the entire reinforcing cloth surface. This mastic shall be pressed so that it penetrates the weave of the doth to obtain a good bond with the first coat (or the cdlular glass insulation) surface. Care shall be that this coat completdy covers, fills, and seals voids in the reinforcing doth. After the mastic has dried, the combined thieknagg of mastic and doth shall measure not less than 1/16 inch. * 2.12.6.5.8. 2.12.6.5.9. Note: The weave pattern of the "extensible" reinforcing doth is such that it will show on the outer surface, regardless of thickness of final coat Where a smooth finish is desired, the final coat may be "water brushed" before it its set Care shall be taken that just sufficient amount of water is used to smooth the surface without diluting the body of the mastic. Spills, dnps, or splatter of mastic on fioors, or other areas not insulated, shall, b;; deaned up with water before mastic sets. VniASCO COATINGS CORP. P. O. Box SIS, Nitra. W. Va,, 2S143 2-33 2.14.1. 2.14.1.1. 2.14.2. 2.14.2.1. 2.14.2.1.1. 2.14.3. 2.14.3.1. 2.14.3.2. 2.14.3.3. 2.14.4. 2.14.4.1. 2.14.4J2. 2.14.4.3. 2.14.4.4. 2.14.4.5. SECTION 2 APPLICATION SPECIFICATION NO. 14 Application Snccilicatioi Augr. 1971 WEATHER-BARRIER INSTALLATION SPECIFICATIONS MODERATE TEMPERATURE EQUIPMENT INSULATED WITH SPRAYED URETHANE RIGID FOAM ACRYLIC EMULSION WEATHER-BARRIER MASTIC AC-7 SCOPE: These specifications provide the essentials and installation procedures for a] cation of weather-barrier over sprayed urethane insulation installed on equipment loc; outdoors or indoors. Limited to equipment whose operating temperature is above amb air temperature. The weather-barrier in this specification is suitable for application over urethane which been sprayed on a substrate surface, foamed, and allowed to cure to its final set prioi installation of the weather-barrier mastic. WEATHER-BARRIER MASTIC AND ACCESSORIES REQUIRED: The acrylic emulsion weather-barrier mastic used shall be that which fulfills the applicati atmospheric and service requirements. Weather-barrier mastic and accessories listed si be of type and have properties, as given in designated section of the MATERIALS 3ECTIC Weather-barrier mastic shall be acrylic emulsion type mastic for application by sprayi suitable for installation at atmospheric temperature down to 40 F. As specified in M TERIALS SPECIFICATION SECTION 1.2.3. (AC-7 Spray Grade). APPLICATION OF SPRAYED FOAM INSULATION: The following is given to provide the essentials as related to proper function of the- Weatht Barrier system. The formulation of the urethane, the thickness required and details of ; application and beyond the scope of this specification. Insulation shall have good adhesion to substrate surface. The surface of the foamed urethane shall be generally' smooth and free of depressions ai cavities. High projection of rigid urethane foam shall be leveled to provide even surface The urethane foam must have had time to complete its reaction. However, it must be coate before solar radiation starts decomposition of the surface. APPLICATION OF WEATHER-BARRIER: Spray application of mastic weather-barrier shall be done with airless spray guns and equij ment which are clean and properly adjusted to obtain a uniformly diffused spray patten Insulation shall be protected from elements of weather until weather-barrier is installed. Spray application of weather-barrier mastic shall be done in two coats. Care shall be take: that each coat of mastic is flowed evenly over the surface. The second coat of mastic shal not be applied until first coat has taken its set. The combined thiclew<*< of the two coats shal be approximately 1/16 inch when dry. Typical application is shown, in Figure No. 21. Weather-barrier mastic shall extend three inches over bare metal which projects beyond th< insulation. Typical application is shown in Figure No. 21. Spills, drips, splatter of mastic on floors, or areas not insulated, must be cleaned up with water before mastic sets. VIMASCO COATINGS COBP. P. O. Box SIS. Nltro. W. 25143 2-35 :.i4. i li ed ait as to n, U vT. s l ' .* r * l * ^ 2.15.3. 2.15.3.1. Application Specification 2.15. Aug. 1971 APPLICATION OF INSULATION ON EQUIPMENT AND PIPING: The following is given to provide the essentials of application of insulations, which require vapor-barriers on low temperature service, as related to the proper function of the vaporbarrier and weather-barrier systems. The type of insulation, its required thickness and de tails of its installation are beyond the scope of this specification. The insulation shall be supported and secured so that after installation all joints axe tight and flush. 2.15.4. 2.15.4.1. 2.15.4.2. 2.15.4.3. 2.15.4.4. APPLICATION OF VAPOR-SEALERS AND VAPOR-BARRIERS: The butt edges of the insulation shall be coated with cold bond adhesive and sealer in suffi cient quantity to fill all voids and provide a vapor barrier down to and sealed to metal. The coated butt edge surfaces shall be placed tightly together to obtain a tightly sealed joint. This provides a laterally compartmentalized vapor seal so.that if outer vapor-barrier is punctured the moisture migration is restricted to a small area of the insulation. Need for this vapor sealing is illustrated in Figure No. 22. The outer surface of each layer of insulation shall be covered, by palming, brushing or spraying, with vapor-barrier coating to an approximate wet thickness of 1/16 inch, so as to obtain a minimum thickness of 1/32 inch when material has dried and cured. At termi nation of block and pipe insulation, at flanges, fittings, or other projections, vapor-barrier should extend down over ends and onto metal to complete the vapor-seal. Ends of block insulation and pipe insulation shall be so sealed before fitting insulation is installed. This is illustrated in Figure No. 23. Pipe insulation, or segmental insulation furnished with factory-attached vapor-barrier jacket shall be installed in similar manner as stated in 2.15.4.1. with end and edge joints tightly butted and vapor-sealed with cold bond vapor-barrier adhesive and sealer. The jacket lap flanges of attached jacket shall be sealed and bonded to jacket over which it extends with lap adhesive. Adhesive shall be applied to the surfaces to be bonded, by brush, at a rate of 80 sq. ft. per gallon. Care shall be taken to obtain tight 100% bond and seal. Where jacket is not supplied with lap flanges to cover joints, the butt jackets shall be coated slightly more than two inches on both sides of the joint with lap adhesive. A strip of same jacketing material, 4" wide, shall be pressed firmly into the wet adhesive to obtain bond and sealing of the vapor-barrier jacket These installations axe illustrated in Figure No. 24. Butt ends and edges extending beyond jacket shall be sealed with vapor-barrier coating applied ap proximately 1/16 inch thick. Fittings, and all insulation without attached vapor-barrier jacket, shall be covered by palming, brushing or spraying, with vapor-barrier coating to an approximate wet thick ness of 1/16 inch so as to obtain a minimum thickness of 1/32 inch when dry. Vapor-barrier coating shall extend over all previously installed adjacent vapor-barriers approximately two inches to obtain seal. - 2.15.5. 2.15.5.1. 2.15.5.2. 2.15.5.3. APPLICATION OF WEATHER-BARRIER: Weather-barrier shall not be installed until vapor-barrier coating has dried. However, it shall be installed as soon after vapor-barrier has taken its set as is practicable and as weather permits. Inside comers, where two planes of insulation join, shall be caulked with caulking and fillet compound to obtain a minimum one inch radius on all inside comers. This is shown in Figure No. 3. ' Weather-barrier mastic shall not be applied when ambient air temperature is lower than recommended minimum installation temperature. Proper grade--regular or spray--shall be used as required by application, method. VXttASCO COATINGS COUP. P. O. Sox SZfl, Nitre, W. Va^ 25143 2-37 2.15.5.5.8. 2.15.5.5.9. Application Specification 2JLS. Aug. 1971 , After mastic has dried, the combined thickness of mastic and cloth shall measure not less than 1/16 inch. Note: The weave pattern of reinforcing cloth will show on the outer surface, regardless of the thickness of the mastic. Spills, drips or splatter of mastic on floors or other areas not insulated and not to be coated shall be cleaned up with water before mastic sets. * VCMASCO COATINGS COBP. P. O. SOX 513. NitTO, W. Va, 23143 2-39 ; 2.16.4.2. 2.16.4.3. 2.16.4.4. Application Spcc'lieatiou 2.1G. Aug. 1071 The coated butt end and edge surfaces shall be placed and secured tightly together to obtain a tightly sealed joint. This provides a laterally compartmentalized vapor seal so that if outer vapor-barrier is punctured the moisture migration is restricted to a small area of in sulation. Need for this vapor sealing is illustrated in Figure No. 22. The outer surface of each layer of insulation shall be completely covered, by palming, brush ing, or spraying, with vapor-barrier coating to an approximate thickness of 1/16 inch, so as to obtain a minimum thickness of 1/32 inch when material has dried and cured. At termination of block and pipe insulation, at flanges, fittings, or other projections, vapor-barrier should ex tend over ends and onto metal to complete the vapor seal. Ends of block and pipe insula tion shall be so sealed before fitting insulation is installed. This is illustrated in Figure No. 23. Pipe insulation, or segmental insulation, furnished with factory attached vapor-barrier jacket, shall be installed with end and edge joints tightly butted and sealed with cold bond adhesive and sealer as in 2.16.4.1. The jacket lap fianges of attached jacket shall be sealed and bonded to jacket over which it extends with lap adhesive. Adhesive shall be applied to the surfaces to be bonded by brush, at a rate of 80 sq. ft per gallon. Care shall be taken to obtain tight 100% bond and seal. Where jacket is not supplied with lap fianges to cover joints, the butt jackets shall be coated slightly more than two inches on both sides of the joint with lap adhesive. A strip of the same vapor jacketing material, 4 inches wide shall be pressed into the wet adhesive to obtain bond and sealing of the vapor-barrier jacket. These joints are illustrated in Figure No. 24. Butt ends and edges extending beyond jacket shall be sealed with vapor-barrier coating applied approximately 1/16 inch thick. Fittings and all insulation without attached vapor-barrier jacket shall be covered by palm ing, brushing, or spraying with vapor-barrier coating to an approximate thickness of 1/16 inch, so as to obtain a minimum thickness of 1/32 inch when material has dried and cured. Vapor-barrier coating shall extend over any previously installed vapor-barrier approxi mately two inches to obtain seal 2.16.5. APPLICATION OF WEATHER-BARRIER: 2.16.5.1. 2.16.5.2. 2.16.5.3. Weather-barrier shall not be installed until vapor-barrier coating has dried. However, it shall be installed as soon after vapor-barrier has taken its set as is practicable. Inside comers, where two planes of insulation join shall be caulked with caulking and fillet compound to obtain a minimum one-inch radius on all inside corners. This is shown in Figure No. 3. Weather-barrier mastic shall not be applied when ambient air temperature is lower than recommended minimum installation temperature. Proper grade--regular or spray--shall be used as required by application method. 2.16.5.4. SPRAY APPLICATION OF WEATHER-BARRIER MASTIC TO LARGE SURFACES 2.16.5.4.1. 2.16.5.4^. 2.16.5.4.3. (Spray application is not recommended on insulation where external diameter is less than 30 inches) Prior to spray application, instruments, gauges and other areas not to be insulated and not to be coated, shall be covered to protect them from splatter, rebound and overspray. Spray application of spray grade mastic shall be done with proper airless spray guns and equipment which are clean and properly adjusted to obtain a uniformly diffused spray pattern. . Over the surface of the vapor-barrier a tack coat of weather-barrier mastic shall be applied. While this coat is still wet the reinforcing cloth shall be embedded into the mastic. The cloth shall be drawn taut and smooth. All doth joints shall be be overlapped a minimum VIMASCO COATINGS CORP. P. O. Box 918. Nitre. W. V*,, 251*3 2-41 2.17.1. 2.17.1.1. SECTION 2 APPLICATION SPECIFICATION NO. 17 Application Specification 2J.7. Augr. 1371 VAPOR-BARRIER AND FINISH INSTALLATION SPECIFICATION INDOOR LOW TEMPERATURE EQUIPMENT AND PIPING (Operating Temperature Below Ambient Air Temperature) VAPOR-BARRIER COATING #740 SCOPE: These specifications provide the list of essential materials and installation proce dures for application of vapor-barriers over insulation on equipment and piping located in doors and operating below ambient air temperature. The vapor-barrier described in this specification is suitable for application on rigid and semi-rigid mineral fiber and organic foam insulations. The mastic finish is suitable for ap plication over sheet and vapor-barrier coatings. 2.17.2. 2.17.2.1. 2.17.23. 2.173.3. 2.173.4. 2.173.5. 2.173.6. VAPOR-BARRIER, COATING FINISH AND ACCESSORIES REQUIRED: The vapor-barrier and coating finish described in this specification shall fulfill the ap plication, atmospheric and service requirements. These and the accessories shall be of the type, and have properties, as given in the designated section of the MATERIALS SPECIFICATION. " Vapor-barrier coating shall be for application by palming, or brushing at atmospheric tem perature down to 20 F, as specified in MATERIAL SPECIFICATION, Section 1.8.1. (#740). Caulking and fillet compound shall be emulsion resin, cork filled type, as specified in MATERIALS SPECIFICATION,. Section 1.5.L (#703-C). Lap adhesive and sealer, shall be rubber type as specified in MATERIALS SPECIFICATION, Section 1.7.1. (#730) or 1.7.3. (#733). Cold bond adhesive and sealer, for service temperature down to --50 F shall be as specified in MATERIALS SPECIFICATION Section 1.4.1. (#750). Reinforcing cloth shall be glass cloth as specified in MATERIALS SPECIFICATION, Section 1.11.2. 2.17.3. 2.17.3.1. APPLICATION OF INSULATION ON EQUIPMENT AND PIPING: The following is given to provide the essentials of application of insulations, which require vapor-barriers for low temperature service, as related to the proper function of the vapor- barrier and weather-barrier systems. The type of insulation, its required thickness and de tails of installation are beyond the scope of this specification. The insulation shall be supported and secured so that after installation all joints are taut and flush. 2.17.4. 2.17.4.1. APPLICATION OF VAPOR-SEALERS AND VAPOR-BARRIERS: The butt edges of the insulation shall be completely coated with cold bond adhesive and sealer in sufficient quantity to fill all voids and provide a vapor-barrier down to and sealed to the metaL The coated butt end and edge surfaces shall be placed and secured tightly to gether to obtain a tightly sealed joint This provides a laterally compartmentalized vapor seal so that if the outer vapor-barrier is punctured the moisture migration is localized. Need for this vapor sealing is illustrated in Figure No. 22. * VIMASCO COATINGS CORP. P. Q. Sox 318, Ni9, W. V*n 29143 2-43 2.18.1. 2.18.1.1. 2.18.2. 2.18.2.1. 2.18.2.2. 2.18.3 2.18.3.1. 2.18.4. 2.18.4.1. \ 2.18.4.2.' 2.18.5. 2.18.5.1. 2.18.5.2. 2.18.5.2.1. SECTION 2 APPLICATION SPECIFICATION NO. 18 Spmliealioa -.lb. Aug. 1U71 CORK-FILLED MASTIC INSULATION APPLICATION SPECIFICATION . INDOOR OR OUTDOOR CONTROL OF CONDENSATION ON EQUIPMENT AND PIPING (Operating Temperature Below Ambient Air Temperature) CORK-FILLED POLYVINYL ACETATE MASTIC WC-1 TYPE C SCOPE: This specification contains the list of essential materials and installation procedures for application of insulation for control of condensation on vessels and piping such as water tanks and piping operating below dew point temperature of ambient air. This specification is not recommended for insulation of refrigerated equipment and piping, and should not be used on substrate operating at temperatures below 35 F. ' The insulation mastic described in these specifications shall be suitable for application to carbon steel, galvanized steel, stainless steel, copper or aluminum surfaces. INSULATING MASTIC AND PRIMERS REQUIRED: The cork-filled polyvinyl-acetate insulating mastic shall be suitable for application by troweling, palming or spraying. It shall be suitable for insulating surfaces operating at temperatures not lower than 35 F nor higher than 180 Fras specified in MATERIAL SPECIFI CATION, Section 1.9.1. (WC-1 Type C). Metal primer for carbon steel shall be iron oxide-zinc yellow as specified in MATERIAL SPECIFICATION, Section 1.13.1. (P. O. F. #52-8), or universal primers specified in MA TERIAL SPECIFICATION, Section L13.4. (#926). PREPARATION OF SURFACE: The metal surface to be insulated shall be dry and clean. Any rust, mill scale, or dirt, shall be removed. Crease, loose paint or oil shall be iviped off with a volatile solvent, such as coal tar naphtha. PRIMING OF CARBON STEEL SURFACES: On previously painted steel, where the paint is in good condition, it is required only that the paint be clean prior to application of cork-filled mastic. However, if paint is glossy or slick it shall be coated with universal primer to obtain good adhesion of the cork filled mastic. Where the existing paint needs repairs the entire surface shall be coated with the universal primer to a dry thickness of at least 1 miL APPLICATION OF CORK-FILLED INSULATING MASTIC: The temperature of the surface to be insulated shall be a minimum of 10 F above dew point temperature, but should not be above 160 ?. Tue surface to which the mastic is applied must remain above dew point temperature until the mastic has dried and cured. A minimum drying period of 24 hours shall be allowed for each 1/8 inch thickness of insulating mastic applied. SPRAY APPLICATION OF CORK-FILLED INSULATING MASTIC: (Spray application is not recommended on vessels or pipe insulation less than 30 inches in diameter). Prior to spray application, instruments, gauges, floors, ceiling or walls shall be covered or shielded to protect them from splatter, rebound and overspray. VIMASCO COATINGS CORP. P. O. Box 516. Nltro. W. Va- 2S143 2-45 2.19.1. 2.19.1.1. 2.19.1.2. 2.19.2. 2.19.2.1. 2.19.2.2. 2.19.2.3. 2.19.3. 2.19.3.1. 2.19.3.1.1. 2.19.3.1.2. 2.19.3.1.3. 2.19.3.1.4. 2.19.4. 2.19.4.1. 2.19.4.1.1. 2.19.4.1.2. 2.19.4.1.3. 2.19.4.2. 2.19.4.2.1. 2.19.4.2.2. SECTION 2 APPLICATION SPECIFICATION NO. 19 Application Spccilicaliou 2.1.0. Aug. 11)71 FIRE RETARDANT COATING OF MET^L, APPLICATION SPECIFICATION INDOORS FIRE PROTECTION OF EQUIPMENT, PIPE AND STRUCTURAL STEEL FIRE RETARDANT COATING (62-10) SCOPE: This specification contains the list of essential materials and application procedures for fire-retardant coating over metal equipment, pipe and structural steel, specifically for protection of steel against high temperature fire exposure lasting not more than 30 minutes. Carbon steel, shall be primed with correct primer (Vimasco 52-8) before application of the fire-retardant coating. Galvanized steel or aluminum shall be primed with an etching vinyl wash primer (Vimasco #806) before application of the fire retardant coating. * FIRE-PROTECTIVE COATING AND ACCESSORIES REQUIRED: The fire-retardant coating shall be suitable for application by brush or spray at tempera tures down to 40 F. It shall be as specified in MATERIAL SPECIFICATION, Section I.I4.2. (P. O. F. #62-10). The fire-retardant topcoat paint shall be suitable to protect the fire-retardant coating from occasional washing without hindering its intumescent property. It shall be suitable for application by spray or brush at atmospheric temperatures down to 40 F. It shall have prop erties as specified in MATERIAL SPECIFICATION, Section X.I4.4. (P. O. F. #52-6). The primer over metal shall be suitable to serve its function as a primer without hindering the intumescent property of the fire-retardant coating. APPLICATION OF FIRE-RETARDANT COATING SYSTEM: PREPARATION OF SURFACES: All metai surfaces shall be clean, free of rust, mill scale, dirt, grease and oil. Carbon steel that has rusted or has mill scale shall be sand blasted to commercial finish. Prior to spray application of primer and fire-retardant coating, instruments, gauges, equip ment, floors, walls and ceilings not to be coated shall be covered to protect them from splatter, rebound and overspray. Carbon steel or iron shall be covered with iron oxide-zinc yellow primer by spray or brush at a rate of 325 sq. ft. per gallon to obtain a minimum dry film thickness of 1 mil. Galvanized steel and aluminum shall be coated with vinyl wash primer by brush or spray at a rate of 400 sq. ft. per gallon to obtain a minimum dry film thickness of 1 mil. APPLICATION INDOORS SHALL BE DONE BY SPRAY OR BRUSH: APPLICATION BY SPRAY SHALL BE AS FOLLOWS: Spray application shall be done with proper air or airless spray guns and equipment which are clean and properly adjusted to obtain a uniformly diffused spray pattern. The coating shall be applied to obtain a dry film thickness of not less than 10 mils. Drip, splatter, rebound or overspray of coating shall be cleaned with suitable solvents (Aromatic #62-10T). BRUSH APPLICATION SHALL BE AS FOLLOWS: Brush application shall be done in multiple coats so as to obtain a total dry film thickness of not less than 10 Mils. Each coat shall be allowed 24 hours drying time before application of the next coat Drip or splaiter of the coating shall be cleaned up with suitable solvent (Aromatic #62-10T). VIMASCO COATINGS CORP. P. O. Box 318. Nltro. W. Va.. 23143 2-47 2.21.1. 2.21.1.1. 2.21.2. 2.21.2.1. 2.21.2.1.1. 2.21.2.1.2. 2.21.3. 2.21.3.1. 2.21.3.1.1. 2.21.3.1.2. 2.21.3.1.3. 2.21.3.1.4. 2.21,3.2. 2.21.3.2.1. 2.21.3.2.2. 2.21.3.2.3. SECTION Z APPLICATION SPECIFICATION NO. 21 Application Sipcciiicatiou 221 Auff. 1971 FINISH OVERCOATING SPECIFICATION . SEMI-GLOSS SURFACE INDOOR AND OUTDOOR INSULATED EQUIPMENT AND PIPING (Service Temperature Low, Medium and High) VINYL-CHLORIDE COATING (Vimasco #10) SCOPE: This specification provides the list of essential materials and installation procedures for the application of a decorative and protective finish over polyvinyl-acetate or acrylic weather-barrier mastics. This specification is recommended for use in caustic handling areas and under certain other extremely corrosive conditions. * Tlie decorative and protective coating described in this specification shall be suitable for application on insulation polyvinyl-acetate or acrylic weather-barriers mastics. This coating shall be suitable for color coding. The dried paint shall provide a weather-resistant, corro sion-resistant, protective, semi-gloss, surface. OVERCOATING AND ACCESSORIES REQUIRED: ' The overcoating and accessories described in this specification shall fulfill the application, atmospheric and service requirements. The vinyl-chloride coating shall be suitable for application by spray or brush at ambient air temperatures down to 40 F. It shall have properties as called for in MATERIALS SPECICATION, Section 1.122. (#10). The thinner and solvent for the vinyl-chloride coating shall be MIBK type. APPLICATION OF VINYL-CHLORIDE COATING: PREPARATION OF SURFACES: All surfaces on which the primers or vinyl-chloride coating is to be applied shall be clean, free of dirt, grease or oil. Where required, the surfaces shall be cleaned with proper solvent The surface temperature must be above dew point when coating is applied. Polyvinyl-acetate and/or acrylic mastic weather-barriers need no primers before application of vinyl-chloride coating. . All weather-barriers shall be patched to obtain continuous unbroken surfaces before appli cation of vinyl-chloride coating. Insulation and weather-barriers must be completely dry before vinyl-chloride coating is ap plied. Small amounts of trapped moisture will cause blisters and bubbles when moisture tries to escape outward. SPRAY APPLICATION: Prior to spray application, instruments, gauges, equipment, floors, ceilings, walls, and other areas not to be coated shall be covered to protect them from splatter, rebound and overspray. Spray application shall be done with proper air or airings spray guns and equipment, properly adjusted to obtain a uniformly diffused spray pattern. Shall be applied in two coats. The vinyl-chloride coating shall be applied at a rate of approximately 225 sq. ft. per gallon to obtain approximately 1.25 mil dry film thickness. VIMASCO COATINGS CORP. P. O. Box SIS. Nitro, W. Va,, 25143 2-49 2.22.1 2.22.1.1 2.22.1.2 - SECTION 2 APPLICATION SPECIFICATION NO. 22 Application Spcruivaliou June, 1972 SEALING AND VAPOR-BARRIER INSTALLATION SPECIFICATIONS - WALLS & CEILINGS OF REFRIGERATED SPACES INSULATED WITH RIGID AND SEMI-RIGID INSULATION VAPOR-BARRIER COATING #740 COLD BOND ADHESIVE AND SEALER #750 SCOPE: These specifications shall provide the list of essential materials and installation procedures for application of vapor-barriers and the sealing of insulation forming low temperature space enclosures. These specifications are restricted to the application of insulation materials which have a water vapor transmission rate of 0.02 or greater. These specifications are also restricted to installations located inside of a building or enclosure. ' The vapor-barrier coating and cold bond adhesive and sealer described in this specification shall be for application on rigid and semi-rigid mineral fiber and organic foam insulations.* 2.22.2 2.22.2.1 2.22.2.2 2.22.2.3 2.22.2.4 2.22.3 2.22.3.1 2.22.3.1 VAPOR-BARRIER COATING AND SEALERS REQUIRED: The vapor-barrier, sealer and adhesive described in these Specifications shall fulfill the application, atmospheric, temperature and service requirements. These shall be of the type and have the properties as given in the designated section of the MATERIALS SPECIFI CATION. . Vapor-barrier coating shall be for application by palming, brushing or spraying, suitable for installation at atmospheric temperature down to 20 F, as specified in MATERIAL SPECI FICATION, Section 1.3.1. (#740). Cold bond adhesive and sealer shall be suitable for service temperature down to--50 F as specified in MATERIALS SPECIFICATION, Section 1.4.1 (#750). Interior finish, or plaster, shall be suitable for service temperature of refrigerated space and shall have a vapor transmission of not less than 5.0 perms. (Note: Selection of this interior lining depends upon so many factors and requirements that an individual material can not be recommended in these specifications). APPLICATION OF INSULATION The insulation is most frequently installed inside, or as part of, a building. Thus, normal forces acting on and contained within the building structure shall be considered and pro vided for in the installation of the insulation. The mechanical design of insulation and the thickness requirements are beyond the scope of these Specifications. Control of water vapor is of paramount importance for efficient operation of Lisulated re frigerated spaces. A vapor-barrier shall be installed on exterior (warm) side of the thermal barrier to prevent excessive amounts of water from entering. This shall be a continuous unbroken vapor barrier. The interior (cold) side of the thermal barrier shall be constructed and of materials to offer little vapor resistance so that any moisture can continue into the refrigerated space. This is shown in Figure No. 27. 2.22.4 2.22.4.1 APPLICATION OF VAPOR-SEALERS AND VAPOR-BARRIERS. WHERE INSULATION IS INSTALLED AGAINST EXISTING WALLS OR CEILINGS The wall or ceiling shall be coated with Ya inch uniform thick layer of Cold Bond Adhesive and Sealer (#750). The insulation shall be thoroughly embedded in the Cold Bond Adhesive *NOTE: The solvents of these coatings may attack some plastic foams. It is recommended to test the insulation with the coating before usage. VIMASCO COATINGS COUP. P. O. liox Sltf. Nitro. W. Va,, 35143 2-51 Application .ipeciiications 1'ii'urc No. t Amj. JU7I WEATHER-BARRIER (Vimasco ,WC~f or AC~7mastic and E/astafab No. 894 doth ) >--caulking and ________________ / FILLET COMFOUND Flanged Fitting Cover Expansion Joint Flush Expansion Joint NOTE! insulation and weather-barrier system shown in section Insulation And Weather-Barrier Expansion Joints --Moderate And High Temperature Service-- ___________________ __ Figure No. 1 . VIMASCO COATINGS CORP. P. O. Bo* 518. Nitro. W. Va., 25143 2-F1 Application Specifications Figure No. :: Auk. I !)71 INSULATION WEATHER-BARRIER OF MASTIC AND REINFORCING CLOTH {Vimasco WC~i or AC-7 mastic and Eiastafab No. 894 cloth J INSIDE CORNER OVERLAPPED REINFORCING CLOTH' APPROX, l" RAOIUS CAULKING AND FILLET COMPOUND OUTSIDE CORNER ROUND CORNER TO APPROX. 1" RAD'US -MODERATE TO HIGH TEMPERATURE SURFAC|7 || WEATHER-BARRIER (Vimasco WC~i or AC~7 and Eiastafab No. 894) INSULATION TERMINATION INSULATION SUPPORT EXTENO WEATHER-BARRIER OVER PROJECTING STEEL FOR A TOTAL DISTANCE OF 4" PROJECTING STEEL, SUCH AS A SKIRT OR A SUPPORT Application Of Caulking Mastic- And Weather-Barrier To Inside And Outside Corners And Terminations --Moderate And High Temperature Service-- _______________________________ Figure No. 3 - VIMASCO COATINGS CORP. P. O. Box SIS. Nitro. W. Va~ 23143 2-F 3 BLANKET OUCT LINER INSULATION PRESSED FIRMLY INTO WET ADHESIVE Low Velocity Duct BLANKET DUCT LINER INSULATION PRESSED FIRMLY INTO WET ADHESIVE High Velocity Duct Application Specifications iMxaire No. .* Au. 15J7I ADHESIVE-% OF AREA DEPENDING ON VELOCITY OF AIR FLOW MECHANICAL FASTENERS SPACED AS SPECIFIED COAT EDGES OF INSULATION WITH ADHESIVE FIRE RESISTANT DUCT ADHESIVE * ADHESIVE APPLIED TO PROPER THICKNESS 8Y SPRAY OR BRUSH HALF SECTION OF DUCT AFTER FORMING * Vimasco No. 730or 733 Application Of Adhesive To Secure Flexible Insulation To Interior Of Duct Figure No. 5 ' VIMASCO COATINGS CORP. P. O. Box 310, Nitre, W. Va,, 25143 2-F5 Aiujlieaiitm Spccilkaiions Figure No. 7 Aug. 1971 VIMASCO COATINGS CORP. P. O. Box 318. Nitro, W. Va, 23143 2-F 7 A|i|ilu:uiun SpcriUculioius Figure .No. Auk. 1971 Sealing And Bonding Of Vapor-Barrier Jacket Over Rigid Fibrous Glass Insulation On Exterior Of Duct Figure No. 9 VIMASCO COATINGS CORP. P. O. Box 513, Nitro, W. Va.. 25143 2-F9 >pvrtlu*;ttious I-iyury No. 11 Au.;<. 1U71 -SPACE ALLOWED FOR SHORTENING OF PIPE DUE TO CONTRACTION 'THIS DISTANCE WILL SHORTEN WITH LOWERING OF PIPE TEMPERATURE Vertical Pipe INSULATION SUPPORT- LOW TEMP PIPE- 1 CELLULAR GLASS INSULATION ^53 SLIP JOINT- wsmt S BMNSS SLIP JOINT g! ALLOWABLE DISTANCE BET ALLOWABLE DISTANCE BET WEEN CONTRACTION JOINTS WEEN CONTRACTION JOINTS THIS DISTANCE WILL SHORTEN WITH LOWERING OF PIPE TEMPERATURE Horizontal Pipe Relative Movement Of Low Temperature Pipe And Insulation Illustrating The Need For Contraction Joints And Anti-Abrasive Coating ^________ Figure No. II VIMASCO COATINGS CORP. P. O. Bos 510. Nitro. W. Va,, 25143 2-FU SECTIONAL INSULATION .Application Spccilicaiiuuj* 1'iuure No. i:: Amu. 15)71 CONTRACTION SPACE FILLET COMPOUND . (Vimasco No. 7'03-CJ HPE ANTI"A8RASIVE COATING- (Vimasco No. 500) CONTRACTION JOINT INSULATION COVER-1 NON-SETTING SEALER (Vimasco No. 750) 1--SLIP JOINT Contraction Joint Single Layer Pipe Insulation PRIOR TO INSTALLATION (Vimasco No. 500) NOTEJNSULATION SHOWN IN SECTION weather-barrier not shown Contraction Joint Multiple Layer Pipe Insulation Construction Of . Low Temperature Pipe Insulation Contraction Joints Figure No. 13 . VIMASCO COATINGS CORP. P. O. Box 516. NiUO. W. Va.. 25143 2-F 13 Application SpccUicatious I'Ufure No. lf Au. 19" t SKEWER BUTT AND LAP HIGH SOLIDS SEALER (Vimasco No. 750) `NON-SETTING SEALER (Vimasco No. 750) CONTRACTION JOINT AT INSULATION SUPPORT SKEWER BUTT AND LAP HIGH SOLIDS SEALER (Vimasco No. 750) INSULATION FLANGE COVER NON-SETTING SEALER CONTRACTION JOINT AT VESSEL FLANGE CYLINDRICAL 80DY INSULATION INNER SURFACE COVERED WITH ANTI-ABRASIVE COATING WHEN SPECIFIED INSULATION SUPPORT SLIP JOINT LOW TEMPERATURE VESSEL INSULATION SUPPORT zVESSEL FLANGE SLIP JOINT TERMINATION OF INSULATION NOTE! TiV '-T!CN ILLUSTRATED IN SECTION- WEATHER- BARRIER NOT SHOWN SKIRT INSULATION SUPPORT Construction Of Low Temperature Vessel Insulation Contraction Joints ______________ __ Figure No. 15 - VIMASCO COATINGS CORP. P- O. Box SW. NItro. W. Va.. 25M3 2-F in A|)l>iU'Uiiuil .SpcciJifUlioiKS Figure No. 17 Autf. 1971 . SPEED CUPS PRESSED '/2 INTO INSULATION SURFACE K PINS CLIPPED BELOW SURFACE \A SURFACE COAT OF COMPRESS*" ED INSULATION -MASTIC WEATHER-BARRIER (Vimasco WC~f or AC-7 mastic and reinforce ment) WIRE NETTING IN LAST '/a* OF INSULATION VESSEL OR EQUIPMENT SURFACE- -SPRAYED MINERAL FIBER INSULATION COMPRESSED TO SPECIFIED THICKNESS FILLED WITH MINERAL FIBER INSULATION FLUSH TO SURFACE Application Of Sprayed Insulation Application Of Wire Netting ,,_ Application Of Mastic Weather-Barrier Application Details For Installation Of Wire Netting Reinforcing For Insulation And Weather-Barrier Figure No. 17 VIMASCO COATINGS CORP. P. O. Box 316. Nltro, W. Va,, 23143 2-F 17 riKUfK No. l!( Auk. 12)71 ) Very Hot Projection Moderate Temperature Projection Application Of Sprayed Fiber Insulation And Heat Resistant Sealer To Hot Projections Through Insulation ____ ________ Figure No. 19 w.VIMASCO COATINGS CORP. P. O. BOX 918, Nitro, Va,, 251 2-F19 9 Ap|lialiou .sicvilicaUou> 1`iKttrc No. ;! Auk, 1971 .MASTIC WEATHER-BARRIER MUST BE SPRAYED IRREGULAR SURFACE OF FOAM INSULATION (Vimasco WC~l or AC-7 mastic) FLOW INTO FOAMED URETHANE INSULATION Enlarged Section Of Sprayed Urethane Foam And Mastic Weather-Barrier METAL VESSEL OR EQUIPMENT SPRAYED URETHANE INSULATION WEATHER-BARRIER MASTIC (Vimasco WC~i or AC-7mastic) FOAM GROUND OR TRIMMED TO PROVIDE AN EVEN TAPER TO ITS TERMINATION POINT ON METAL SURFACE MASTIC WEATHER-BARRIER EXTENDING OVER METAL TO SEAL TERMINATION OF INSULATION Mastic Seal At Termination Of Line Of Sprayed Insulation Application Of Weather-Barrier Mastic To Sprayed Urethane Insulation Figure No. 2! VIMASCO COATINGS CORP. P. O. Box 516, Nitro. W. Va.. 25M3 2-F21 Application Spociiicutiuiis Figure No. 23 AS. IN" l VIMASCO COATINGS CORP. P. O. Box SIS. Nitro. W. Va., 25143 2-F23 .A [ijjlicmiiiu SticciitcaUuu.s Figure No. 25 Aut,'. IU71 I NOTEjnsulation SHOWN IN SECTION I Of outdoors, overcoat vapor-barrier with Vimasco WC-i or AC~7mastic reinforced with E/astafab No. 894 doth ) Application Of Vapor Sealing Of Insulation Covers To Equipment Body And Pipe Covering Insulation Figure No. 25 VIMASCO COATINGS CORP. P. O. Box 518. Nitro, W. Va.. 25143 2-F 25 Application SycciiicaUoiw I'lKUrc No. 27 June 1972 1 Outside INSULATION IN WALL OR CEILING OF REFRIGERATOR DIRECTION OF WATER-VAPOR FLOW' HIGH VAPOR ____ PRESSURE AREA VAPOR-BARRIER ON OUTER SURFACE SHOULD RESTRICT THE PASSAGE OF WATER-VAPOR---------- * (//masco No. 750 when attached to existing waifs, Vimasco No. 740 when exposed) Refrigerated Space VAPOR WHICH PASSES THROUGH VAPOR-BARRIER SHOULD FLOW TO THE COLO AREA JLlow vapor PRESSURE AREA INNER WALL SURFACE SHOULD NOT BE SEALED SO THAT PASSAGE OF WATER-VAPOR WILL NOT BE RESTRICTED z--INSULATION WHICH HAS VAPOR TRANSMITTANCE GREATER THAN 0.02 PERMS Diagram Of Insulated Wall Or Ceiling Of Refrigerated Space Figure No. 27 VIMASCO COATINGS CORP. P. O. Sox 516. Nuro. W. Va. 23 H3 2-F27