Document 1yjV1a0145k0ZQ370MMBGQxvZ

1# 4 Safety Pate Sheet H-0165, H-Oie, H-2X65, H-218, H-305, H-^o, H-627. H--711 H-727. H-816S. H-827. H-8_2<)--------------Waffle used on label: Kane Ace CPVC 2-i.Manufacturer's Address: Kanegafuchi Chemical Industry No. 3-Chome. Hakanoshiroa Kita-Ku. Osaka JAPAN Tele. (713) 840-1751/Emer. (713) *7*-lM* Chemical name: Chlorinated Polyvinyl Chloride Chemical family/use Vinyl Chloride Polymer ingredients Identity Chlorinated polyvinyl Chloride Residual Aliphatic Chlorinated Hydrocarbons 4 Cas No. 686H8-82-8 Vtf >98* <0.1% TLV NE, see Respiratory Protection Section PHYSICAL DATA t Boiling Point: N/A Specific Gravity: 1*5 - 1*6 Vapor Density: N/A Volatiles: <0.3 wt* Molecular weight: N/A Appearance and odor: White Powder Freezing Point: N/A Vapor Pressure: N/A Solubility in water: Insoluble Evaporation rate: N/A pH: N/A Practically odorless FIRE AND EXPLOSION DATA Flash Point: N/A Autoignition temp ND Flammable limits: LEL N/A UEL = N/A Extinguishing media: Water spray, avoid scattering burning material or creative dust hazard with water stream, or dry chemical. (ABC Type.) Special fire fighting procedures: Avoid eye and skin contact. Do not breathe fumes. Do not inhale dust. Wear positive pressure self"contained breathing apparatus (SCBA). Personnel not having suitable respiratory protection * "' ^ ~~ " combustion gase_s__f_ro__m any s.o__u_r_c_e_. In enclosed or poorly wear SCBA during cleanup immediately after a fire as well as during the attack phase of firefighting operations* Use water spray 4t"o~ keep containers cool* page 1 of 5 D-107 1I I* J 1 Revised 890306 VAB.0001072186 i ft*' -*-1 -h i-i rt t r* . | hi ft -i-.- -.-i 4 4 t Material Safety Data Sheet H-0165, H-018, r H-2X65* H-218, H-305, IHI08, H-516A, H-5165. H-526, H-527, H-627,*H_711. H-7271 H-8165, H-827, H-829 and explosion hazards: Hydrogen chloride, a combustion a^ corrosive effect on m^any__m.ei_ta_l_s. wA*.4ff1e*4c4tne**d aenqiMulilpnmhebntW. unprotected structural elenn remove depositions ENVIRONMENTAL INFORMATION Spill response: Carefully vacuum up material and place in $ suitable container for disposal. Avoid creating a dusty atmosphere. Recommended container. disposal Federal, Dispose of material as solid waste in a closed State and Local regulations should be observed when disposing. HEALTH HAZARD DATA Eye Contact: May cause irritation. Skin Contact: May cause irritation and/or dermatitis. Inhalation: Treat as nuisance dust. Avoid breathing processing vapors which will irritate respiratory tract. Under any condition (processing, decomposition, etc.), symptoms such as coughing, tearing, and irritation should be regarded as potentially hazardous and measures taken to avoid exposure. Acute toxicity: No known erfects. Eyes: In case of contact, immediately rlush eyes with flowing water for at least 15 minutes, occasionally lifting upper and lower lids, until no evidence of chemical remains. Get medical attention. Skin: Wash area with mild soap and water. Inhalation: Move exposed individual to fresh air. Call a physician.____ ____ REACTIVITY Stability: Stable Conditions to avoid: Take avoid decomposition. Incompatibility (Material acetal, acetal copolymers Page 2 of 5 D-107 extended times to Avoid contact with 4-^ Revised 890306 a f VAB.0001072187 r J".'- '"r 1 ? .................................-.,-:,'Tr,TTVli'L-- - t Material Safety Data Sheet H-0165, H"0l8, H-2165, H-218, H~305. H-408, H-51&A, H-5165, H-526, H-27, H'-627, H-711, H-727, H-8165, H-827, H-829 materials during processing. If processed together, these materials may be mutually destructive and degrade rapidly. Prevent cross contamination-of feedstocks. Thoroughly purge and mechanically clean processing equipment to prevent these materials from coming in contact with each other. Hazardous polymerization: Will not occur. ^. Hazardous decomposition products: Carbon monoxide* carbon dioxide, various oxidized and non-oxidized hydrocarbons, hydrogen chloride, chlorinated hydrocarbons. SPECIAL PROTECTION INFORMATION Ventilation: Local exhaust is recommended. Virtually all thermoplastic materials will emit fumes and/or vapors when heated to processing temperatures. The concentration of these emissions in the workplace air will depend upon variables such as the specific compound formulation, amount processed, processing method and temperature and the effectiveness of exhaust ventilation. Always use CPVC compound under well-ventilated conditions and avoid continued or prolonged breathing of process vapors. Processing fume condensate may include toxic contaminates and should be periodically removed from exhaust hoods, ductwork and other surfaces. Rubber gloves should be worn during cleanup operations to prevent skin contact. Respiratory protection: Use NIOSH approved high efficiency dust respirator when dusty conditions prevail. No TLV-TWA has been established for this dust. The AGCIH recommend that nuisance particulates be limited to 10 mg/ M3, total dust. Abnormal conditions such as equipment malfunction, use of improper equipment or procedures, or hangup or stagnation of compound during processing may cause decomposition. If general dilution or local exhaust ventilation is not adequate to keep fume or vapor concentrations at non-irritating levels, then employees involved in removing decomposing material must be provided with suitable air supplied respirators, such as NIOSH/MSHA approved positive pressure self-contained breathing apparatus. Eye and face protection: Chemical workers goggles. Do not wear contact lenses. Other clothing and equipment: An eyewash and emergency shower should be readily available. Launder contaminated clothing before reuse. Page 3 of 5 D-107 4 n Revised 890306 n * 4 VAB.0001072188  *4r MateriaX Safety Data sheet H-0165, H-018, H-2165 , H-218, H-305, H-*I08 , H-516A, 11-5165, H-526, H-527 ? 11-627, H-711, H-727, H-8165, H-827, H-829 V SPECIAL PRECAUTIONS .I Precautionary label information; Cau contact with eyes, skin and doting* Avoid Wash thoroughly alter handling. Storage ana handling: Store in original container in cool, ary Sprinklered warehouse areas are recommended. CPVC compound by 1 will not support combusion but other combustibleconen3(e.g. pallets, caraboara boxes, ete.) can provide sufficient fue> to force cpvt Othe^Precautions: ventilate area properly to avoid unnecessary exposure to resulting gases which might be hazardous. Do not store near high temperature boilers.heaters, pipes or open flames. For industrial use only. TRANSPORTATION Department of transportation (DOT) DOT proper shipping name; Not required. DOT hazard class: Not required. DOT label: Not required. DOT ID f: Not required* NFPA RATING A Health: Flammability: Reactivity; 2 1 0 MISCELLANEOUS Prepared by Environmental & Process Safety Department The information set forth herein has been gathered from standard reference materials and/or Kanegafuchi/KTC test data and to our best knowledge and belief accurate and reliable. Such information is offered solely for your consideration, investigation and verification, and it is not suggested or guaranteed that the hazard precautions or procedures mentioned are the only ones which exist. Kanegafuchi/KTC makes no warranties. Page 4 of 5 D-107 Revised 890306 * + t h VAB.0001072189 M i: *.1 ihj. 1 - ir i i^.-h, 1- ' 1 * J- ' + ft I * ' I . I IKI-"' +-T ^ H-, f T 1 ' I * * * I Material Safety Data Sheet H-0165, H-018 H-2165, H-218, H-305* H-408, H-516A, H-5165, H-526, H"527, H-627, H-7U. H-727, H-8165. H-827, H-829 exptrheesssooprrecminifcpiciit*emda tewriitahl rI.ed_s_e_pn_et.ci.ft.ie_todj the use herein of in csouecbhinninanHtfiooornnm^wartiiittohhnaaon^yrotthheeru^se material^orproceaaand, tberefore, assumes no aid use procedures, safe handling and use reeains the. responsibility of the customer* Page 5 of 5 D-107 IJ % Revised 890306 ..... f 'P- mf ' ^ '****< I VAB.0001072190 TOTAL P.06 ... ,, ............................................. .... . - r .. . k! - ...HI KANEKA vMHR/1 TCFOXRAP^ORATION MATERIAL SAFETY DATA SHEET PRODUCTION IDENTIFICATION Manufacturer's Address Trade Name Chemical Name & Synonyms Chemical Family Formula KANEGAFUCHI CHEMICAL INDUSTRY CO., LTD. 2-4, 3 Chome, Makanoshima, Kita-Ku, Osaka, Japan Kane Ace B-56 MBS Resin Impact Modifier Resin MMA-Bd-St Acrylic Copolymer Telephone No. (713) 840-1751 Emergency No. (713) 474-7084 Toll Free 1-800-526-3223 HAZARDOUS INGREDIENTS (None listed by NTP Annual Report on Carcinogens) PAINTS, PRESERVATIVES, & SOLVENTS TLV ALLOYS AND METALLIC COATINGS TLV Pigments Catalyst Vehicle Solvents Additives Others N/A Base Metals N/A Alloys N/A Metallic Coatings N/A Filler Metal Plus Coating N/A or Core Flux N/A Others N/A N/A N/A N/A N/A Hazardous mixtures of other liquids, solids or gases. N/A Boiling Point (F) Vapor Pressure (mm^g) Vapor Density (AIR=1) Solubility in Water Appearance and Odor PHYSICAL DATA N/A Specific gravity (H20=l) 0.9 - 1.0 N/A Percent Volatile by Volume (%) Less than 1.5* N/A Evaporate rate N/A Non- Soluble Fine White Powder with Slight Acrylic Ester Odor -- i- li^iih -- n *** --' H'pil^'HHMIliPH |ia.--- Mill i i Ip j IfcWPiH .ipj| J.J . Jll.lllHl -t i nr^s< TP HP VAB.0001072191 *wm VWP' * FIRE AND EXPLOSION HAZARD DATA Flash point Fenwell ASTM D1929 Autoignition Temperature 460-470C Extinguishing Media Special Fire Fighting Procedures Unusual Fire and Explosion Hazards Flammable Limits Uel ND Lei 25g/m3cloud Water or Dry Chemical Agent (ABC Type) Water or Dry Chemical Agent (ABC Type) At concentration of 25 g/m3 or greater, there is a possibility of dust explosion. Dust generation should be minimized and every ignition source such as fire, open flame, static sparks, etc., even in closed pipe line equipment, should be strictly prohibited as with all organic matters. HEALTH HAZARD DATA Threshold Limit Value Effects of Overexposure Emergency and First Aid Procedures + Not established. No reports of over-exposure irritations. This material will not indicate any acute toxicity. If contact with eyes, flush with water. If contact with skin, flush with water. If ingestion occurs, contact physician. REACTIVITY DATA _ h Stability Incompatability (Materials to avoid) Hazardous Decomposition Products Hazardous polymerization will not occur. Stable Avoid contact with strong Oxidizing agents. Odorous fumes may result under normal processing. Thermal degradation is caused by high temperature. SPILL OR LEAK PROCEDURES Steps to be taken in case material is released or spilled: Clean spilled area with suction or vacuum equipment. Waste Disposal Method: By Landfill or by incineration if allowed. (2) VAB.0001072192 1 1 SPECIAL PROTECTION INFORMATION Respiratory Protection Ventilation Protective Gloves Eye Protection Others Recommend dust mask be used when handling. Proper ventilation reduces unnecessary exposure to degradation gases under processing. Recommend gloves. Recommend goggles. None. SPECIAL PRECAUTIONS Precautions to be taken handling and storing: Store in original container in cool, dry area. When transferring, avoid creating dust. Ground all equipment to avoid static spark. Other precautions: Ventilate area properly to avoid unnecessary exposure to resulting gases which might be hazardous. Do not cause dust clouds or static sparks. Do not store near high temperature boilers, heaters, or pipes. NFPA RATING A Note: The information presented herein, while not guaranteed, was prepared by technical personnel and is true and accurate to the best of our knowledge. While our technical personnel will be happy to respond to questions regarding safe handling and use procedures, safe handling and use remains the responsibility of the customer. VAB.0001072193 r..... ITT =- 'Hi