Document 0NamdKwXYY3YMj8oLpzQmmLV

MATERIAL SAFETY DATA SHEET Attach! (Approved by U.S. Department of Labor "Essentially Similar"- to Form LSB-OOS-4) t_ "F" UCAR BISPHENOL A 4, 4' - Isopropylidenediphenol (H3C)2C(C6H40H)2 .ME AND SYNONYMS: UCAR Bisphenol A CHEMICAL FAMILY: Aryls MOLECULAR WEIGHT: 228.28 NG POINT, 7.6 mm. Hg CIFICGRAVITY(H20-1) APOR DENSITY (air-1) PER CENT VOLATILES BY VOLUME APPEARANCE AND ODOR 230*0. (446.0* F.) FREEZING POINT 1.195 at 25/25*C. Not applicable 0 VAPOR PRESSURE AT 20*C. SOLUBILITY IN WATER. % by wt. at 20*C. EVAPORATION RATE (Butyl Acetate - 1) White flakes or prills; mild phenoli<:odor. 157*C. Not applicable <0.1 Not applicable MATERIAL Not applicable TLV (Units) m FLASH POINT (test method) Not applicable FLAMMABLE LIMITS IN AIR. % by volume _____ naamn_____ FLASH IGNITION TEMPERATURE LOWER Not applicable 540 F. (ASTM D 1929) UPPER Not applicable EXTINGUISHING MEDIA Use carbon dioxide or dry chemical for small fires. Use ordinary foam for large fires. SPECIAL FIRE FIGHTING PROCEDURES None, except avoid dust clouds. UNUSUAL FIRE AND EXPLOSION HAZARDS Dust is explosive when particles are finer than 200 Tyler mesh (-74 microns). Minimum Explosive Concentration, 0.020 ounces of solid/ft.3 of air. Minimum Ignition Temperature of Cloud, approximately 1,000F. Minimum Ignition Energy, 0.015 joules. Or. C. U. Darnehl, 212/551-4785 Dr. K. S. Lane, 212/551-4787 C. P. Carpenter, Ph.D., 421/327-1020 . 212/551-2345; 304/744-3487 (nights, weekends, and holidays) RNW 0503 While Union Carbide Corporation believes that the data contained herein are factual and the opinions expressed are those of nua*,'i experts regarding the results of the tests conducted, the data are not to be taken as a warranty or reoresentation for which Umo Carbide Corporation assumes legal responsibility. They are offered solely for your consineration, investigation, and verification UNION CARBIDE CORPORATION CHEMICALS AND PLASTICS 270 PARK AVENUE, NEW YORK, N.Y 10017 i'IRST Not yet established May cause skin irritation. Dust and solutions of Bisphenol A cause eye injury. Flush skin contact with water. In case of contact with eyes, immediately flush with plenty of water for at least 15 minutes, and then call a physician. ^STABLE STABLE - ________V________ INCOMPATIBILITY (materials to avoid) CONDITIONS TO AVOID None None HAZARDOUS DECOMPOSITION PRODUCTS HAZARDOUS POLYMERIZATION May Occur Will not Occur V .O'it ' t Thermal decomposition or burning may produce carbon monoxide and/or carbon dioxide. CONDITIONS TO AVOID .I None yis^spiagORg^sii^RGEiSM STEPS TO BETAKEN iF MATERIAL IS RELEASED OR SPILLED Shovel up and flush excess with water. WASTE DISPOSAL METHOD Bury in a landfill. RESPIRATORY PROTECTION -- (specify type) LOCAL EXHAUST VENTILATION MECHANCIAL (general) Dust respirator Preferred -- PROTECTIVE GLOVES OTHER PROTECrrivE EQUIPMENT Rubber Eye bath and safety shower. SPECIAL OTHER EYE PROTECTION -- -- Coverall goggles PRECAUTIONA RY LABELING OTHER HANDLING AND STORAGE CONDITIONS P-43571 UCAR BISPHENOL A WARNING! CAUSES EYE INJURY AND SKIN IRRITATION. Do not get in eyes. Avoid prolonged or repeated contact with skin. In case of contact with eyes, immediately flush with plenty of water for at least 15 minutes; call a physician. Wash thoroughly after handling. FOR INDUSTRY USE ONLY RNW 0504 Printed rn U S.A.