Document wqN4yQMZ7VE6zXLr750grqod
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
PIPING SPEC CODE: L101 DATE: 02-11-94
PAGE: 1 OF 21
DRY CHLORINE (LIQUID & GAS) 440. PSIG AT 125. DEG. F TO -50. DEG. F TEST CLASS & PRESS: C @ 660 MATERIAL: LOW TEMPERATURE CARBON STEEL CORROSION ALLOWANCE: .0625 INCHES INDUSTRY PIPING CODE: ASME B31.3-1990 EDITION
ITEM
SIZE
DESCRIPTION
NOTES
NOTE <n> NOTE <n>
NOTE <n> N73 7
NOTE <n>
CAUTION CAUTION
PRESSURE AND TEMPERATURE LIMITING FACTORS ARE LARGE BRANCH CONNECTIONS AT 440 PSIG AND PIPE AND FITTINGS AT -50 DEGREES F.
THIS PIPING SPEC CONFORMS TO PIPING CODE ASME B31.3, NORMAL SERVICE, IN REGARDS TO INTERNAL PRESSURE AND TEMPERATURES STATED ABOVE IN HEADER DESCRIPTION. CHECK COMPLETED ON 08/07/92. ADDITIONAL APPLICABLE CODE EVALUATIONS SHOULD BE PERFORMED AT THE PROJECT LEVEL FOR CONDITIONS SUCH AS EQUIPMENT NOZZLE LOADINGS, STRESSES DUE TO THERMAL EXPANSIONS, WEIGHT, LIQUID EXPANSION, ETC.
TITANIUM METAL REACTS CATASTROPHICALLY WITH DRY CHLORINE . DO NOT USE TITANIUM METAL COMPONENTS IN THIS SERVICE.
PIPING ON THIS SPECIFICATION SHALL BE ALL WELDED AND/OR FLANGED INCLUDING THE FIRST BLOCK VALVE OFF THE LINE IN INSTRUMENT PIPING AND ALL VENT AND DRAIN VALVES.
ALL CHARPY TESTED -50 DEG F PIPE AND FITTINGS TO BE SPRAY PAINTED WITH A YELLOW STRIPE AS WELL AS TO BEAR ASTM NUMBER.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 046744 OONFTDFNTT Al
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE INSPECTION
NOTE <n>
NOTE <n>
NOTE <n>
NOTE <n>
NOTE <n>
NOTE <n>
CL105
NOTE <n> N9 3 A
INSPECTION INSPECTION WELDING WELDING
CLEANING CLEANING CLEANING
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 2 OF 21
DESCRIPTION
20% OF ALL CIRCUMFERENTIAL BUTT AND MITER GROOVE WELDS SHALL BE RANDOM RADIOGRAPHED. ACCEPTANCE SHALL BE IN ACCORDANCE WITH SEVERE CYCLIC CONDITIONS CRITERIA.
5% OF ALL SOCKET WELDS SHALL BE SPOT RADIOGRAPHED TO VERIFY CORRECT SOCKET GAP AND WELD QUALITY.
A VISUAL INSPECTION IS REQUIRED IN ACCORDANCE WITH CODE CRITERIA FOR 'NORMAL'CATEGORY SERVICE.
WELDING AND FABRICATION SHALL BE IN ACCORDANCE WITH DOW SPECIFICATION L8S-6500-01.
APPLICABLE DOW WELDING PROCEDURES: SHOP FABRICATION - L8S-6501-BZ, L8S-6501-GE AND L8S-6501-BD; FIELD FABRICATION L8S-6501-BZ AND L8S-6501-GE.
PIPING SHALL BE INSTALLED IN ACCORDANCE WITH ENGINEERING SPECIFICATION L4S-4210-01 AND TESTED PER ENGINEERING SPECIFICATION L4S-6410-01.
FLANGE BOLTING SHALL BE INSTALLED IN ACCORDANCE WITH DOW ENGINEERING SPECIFICATION L5C-3800-00, BOLT TORQUE TABLE #4.
BEFORE INSTALLATION, CLEAN ALL OIL, GREASE, DIRT AND FOREIGN MATERIAL FROM INSIDE OF PIPE AND FITTINGS.
FOR SPECIFIC CLEANING INSTRUCTIONS, PLEASE REFER TO PROJECT SPECIFICATIONS.
ALL VALVES SHALL BE DEGREASED, SEALED AND TAGGED AT FACTORY FOR CHLORINE SERVICE.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
0 A 04 6/4 6
CONFTDFNT TAl'
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM N245
SIZE
NOTE <n> NOTE <n>
N217
CAUTION DESIGN
NOTE <n> N238
NOTE <n>
NOTE <n> PIPE
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 3 OF 21
DESCRIPTION
SEE ENGINEERING SPECIFICATION N4S-9803-01 FOR ACCEPTABLE MANUFACTURERS OF PIPE AND PIPING COMPONENTS.
BUTTERFLY VALVES SHOULD BE AVOIDED IN LIQUID CHLORINE SERVICE.
WHEN SELECTING BALL VALVES, USE STANDARD PORT VALVES UNLESS PRESSURE DROP CONSIDERATIONS JUSTIFY THE USE OF FULL PORT VALVES.
FOR COLD LIQUID OR GAS SERVICES, ALL PLUG AND BALL VALVES WITH THE EXCEPTION OF VALVES HAVING SELF RELIEVING SEATS, SHALL HAVE A RELIEF HOLE DRILLED ON THE UPSTREAM SIDE OF THE BALL OR PLUG AND BOTTOM OF THE PLUG; DIRECTIONAL FLOW ARROW SHALL BE PERMANENTLY PLACED ON VALVE BODY.
PACK WEATHERPROOF GEAR OPERATORS ON VALVES WITH NO-OXIDE A GREASE.
CAUTION: CHLORINE LINES SHALL BE PLACED IN THE PIPEWAYS SO THAT NO LINES CARRYING CORROSIVE MATERIALS SHALL PASS OVER THEM.
PROVIDE WELDED PIPS' SHOES FOR ALL BUTT WELDED PIPING AT PIPE SUPPORTS. WEAR PLATES ARE PROHIBITED. AVOID THE USE OF BOLTED SHOES, CLEVIS, AND U-BOLT TYPE SUPPORTS. SEAL WELDED PLATE LUGS ARE PREFERRED FOR ATTACHMENT OF PIPE HANGERS TO PIPE
DO NOT ROUTE PIPE SIZES SMALLER THAN 2" IN PIPE RACKS.
P13 3
1/2-4
PIPE: EXTRA STRONG; SEAMLESS; ASTM A 333 GR 6; LOW TEMPERATURE CARBON STEEL. CHARPY TEST AT -50 DEG F.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 046746 CONFTDFNTT Al
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM P132
SIZE 6-12
PIPE NIPPLES
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 4 OF 21
DESCRIPTION
PIPE: STANDARD WEIGHT; SEAMLESS; ASTM A 333 GR 6; LOW TEMPERATURE CARBON STEEL. CHARPY TEST AT -50 DEG F.
PN763SW
1/2 - 1 1/2
PN763SWXL
1/2 - 1 1/2
BRANCH CONNECTIONS
PIPE NIPPLE: SCHEDULE 160; SEAMLESS; ASTM A 333 GR 6; LOW TEMPERATURE CARBON STEEL; 3 IN LONG; PLAIN ENDS. CHARPY TEST AT -50 DEG F.
PIPE NIPPLE: SCHEDULE 160; SEAMLESS; ASTM A 333 GR 6; LOW TEMPERATURE CARBON STEEL; 6 INCHES LONG; PLAIN ENDS. CHARPY TEST AT -50 DEG F.
BC1
HEADER SIZE
NINETY DEGREE BRANCHES SHALL BE DESIGNED AND INSTALLED IN ACCORDANCE WITH THE FOLLOWING TABULATION:
BRANCH SIZE
BRANCH SAME AS HEADER OR SMALLER
CONNECTION
NOTE <n>
FITTINGS
1/2 3/4 232-
-1 -1 12 12 12
1/2 1/2
1/2 1/2
221/2
-1 -1 12 10 -1
1/2 1/4
1/2
SAME SMALLER SAME SMALLER SMALLER
TEE RED.TEE,SWAGE TEE PLAIN STUB IN SOCKOLET
E214
1/2 - 1 1/2
ELBOW 90 DEG: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 046747 C.ONF TDFNTTAI
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM L214
SIZE 1/2 - 1 1/2
T214
1/2 - 1 1/2
TR214
1/2 - 1 1/2
RC214
1/2 - 1 1/2
RC42P
1/2 - 2
RE42P
1/2 - 2
C27AC
1/4 - 1 1/2
C27AS
1/4 - 1 1/2
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 5 OF 21
DESCRIPTION
ELBOW 45 DEG: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.11. CHARPY TEST AT -50 DEG F.
TEE: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
TEE REDUCING: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
REDUCING COUPLING: SOCKET WELDING; CLASS 3 000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
SWAGED NIPPLE CONCENTRIC: PLAIN BOTH ENDS; EXTRA STRONG; SEAMLESS; ASTM A 333 GR 6; LOW TEMPERATURE CARBON STEEL. CHARPY TEST AT -50 DEG F.
SWAGED NIPPLE ECCENTRIC: PLAIN BOTH ENDS; EXTRA STRONG; SEAMLESS; ASTM A 333 GR 6; LOW TEMPERATURE CARBON STEEL. CHARPY TEST AT -50 DEG F.
COUPLING: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
STRAIGHT TYPE O-LET BRANCH: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F. ANVIL (CANVIL) SOCKET WELD ANVILET BONNEY FORGE SOCKOLET WFI INTERNATIONAL, INC. SOCKET WELD PIP PENNSYLVANIA MACHINE WORKS SOCKET WELD PHOENIX SOCKET WELD TRANS-O-CON
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
D0 A 046740 c0NFlOFNT^1
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM C27ASL
SIZE 1/2 - 1 1/2
C47N
1/2 - 1 1/2
C47C
1/2 - 4
PC34 E215 L215
1/4 - 1 1/2 2-4 2-4
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 6 OF 21
DESCRIPTION
ELBOW TYPE O-LET BRANCH: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll; CHARPY TEST AT -50 DEG F. ANVIL (CANVIL) ELBOW ANVILET BONNEY FORGE ELBOLET PENNSYLVANIA MACHINE WORKS ELBO OUTLET PHOENIX TRANS-O-CON OULET CONNECTION WFI INTERNATIONAL, INC. ELBO PIPET
NIPPLE TYPE O-LET BRANCH: PLAIN END; EXTRA STRONG; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; 3 1/2 INCH.LONG. CHARPY TEST AT -50 DEG F. BONNEY FORGE NIPOLET PENNSYLVANIA MACHINE WORKS NIPPLE OUTLE WFI INTERNATIONAL, INC. NIPPLE PIPET
STRAIGHT TYPE O-LET BRANCH: BUTT WELDING; SCHEDULE 80; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F. ANVIL (CANVIL) BUTT WELD ANVILET BONNEY FORGE WELDOLET PENNSYLVANIA MACHINE WORKS BUTT WELD OU PHOENIX BUTT WELD TRANS-O-CON WFI INTERNATIONAL, INC. BUTT WELD PIPET
CAP: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
ELBOW 90 DEG LR: BUTT WELDING; EXTRA STRONG; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
ELBOW 45 DEG: BUTT WELDING; EXTRA STRONG; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 04A749 f.ONF T DFNT T Al
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM T215
SIZE 2-4
TR215
2-4
RC215
2-4
RE215
2-4
E41A
6-12
L41A
6-12
T41A
6-12
TR41A
6-12
RC41A
4-12
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 7 OF 21
DESCRIPTION
TEE: BUTT WELDING; EXTRA STRONG; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
TEE REDUCING: BUTT WELDING; EXTRA STRONG; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
REDUCER CONCENTRIC: BUTT WELDING; EXTRA STRONG; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
REDUCER ECCENTRIC: BUTT WELDING; EXTRA STRONG; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
ELBOW 90 DEG LR: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
ELBOW 45 DEG: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
TEE: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
TEE REDUCING: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
REDUCER CONCENTRIC: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 046750 OONFTDFNTTAI
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM RE41A
SIZE 4 - 12
FLANGES F126RF80
1/2 - 1 1/2
F29ARF8 0
2 -4
F29ARFSTD
6 - 12
F28ARF
1/2 - 12
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 8 OF 21
DESCRIPTION
REDUCER ECCENTRIC: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 420 GR WPL6; LOW TEMPERATURE CARBON STEEL; ASME B16.9. CHARPY TEST AT -50 DEG F.
FLANGE: SOCKET WELDING; CLASS 300; RAISED FACE; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.5. BORE TO MATCH SCHEDULE 80. CHARPY TEST AT -50 DEG F. THE FINISH OF THE GASKET CONTACT FACE OF.FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
FLANGE: WELDING NECK; CLASS 300; RAISED FACE; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.5. BORE TO MATCH SCHEDULE 80. CHARPY TEST AT -50 DEG F. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
FLANGE: WELDING NECK; CLASS 300; RAISED FACE; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.5; BORE TO MATCH STANDARD WEIGHT. CHARPY TEST AT -50 DEG F. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
FLANGE: BLIND; CLASS 300; RAISED FACE; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.5. CHARPY TEST AT -50 DEG F. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 0467S1 CONFtdfnttai
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM GASKETS
SIZE
G34A
1/2 - 12
FASTENERS BA193B7QC
BA193B7QCSC
BOLT LUBRICANT BL10
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 9 OF 21
DESCRIPTION
GASKET: SPIRAL-WOUND; MONEL 400 WINDING; TEFLON FILLER; 0.175 INCH THICK; API 601 FOR ASME/ANSI B16.5 FLANGES; CARBON STEEL CENTERING RING; MONEL INNER RING. FLEXITALLIC CGI FURON RW LAMONS WRI STERLING GR-IR
COATED STUD BOLT: ASTM A 193 GR B7; LIQUID QUENCHED AND TEMPERED; ALLOY STEEL; WITH ASTM A 194 GR 2H HEAVY HEX NUTS. STUD BOLTS AND NUTS TO BE FLUOROPOLYMER COATED, COLOR TO BE BLUE. FLUOROPOLYMER COATING TO BE AS SUPPLIED BY STANCO BOLT DIVISION, METALS COATING CORP., PROTECTIVE COATINGS INC., OR INDUSTRIAL METAL FINISHING CO.
COATED CAP SCREW: ASTM A 193 GR B7; LIQUID QUENCHED AND TEMPERED; ALLOY STEEL. CAP SCREWS TO BE FLUOROPOLYMER COATED, COLOR TO BE BLUE. FLUOROPOLUMER COATING TO BE AS SUPPLIED BY STANCO BOLT DIVISION, METALS COATING CORP., PROTECTIVE COATINGS INC., OR INDUSTRIAL METAL FINISHING CO.
BOLT LUBRICANT: PASTE, NICKEL BASED, ANTISEIZE COMPOUND. FEL PRO NICKEL EASE FEDERAL PROCESS CO. THRED-GARD NICKEL NEVER SEEZ NICKEL SPECIAL
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE*. L101
DO A 04675? OONFTOFNTTAl
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE
VALVES
VGL300LC10ARF 1/2 - 1
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 10 OF 21
DESCRIPTION
BOLT LUBRICANT IS REQUIRED ONLY WHEN FLUOROPOLYMER COATING IS DAMAGED, OR WHEN REUSING EXISTING NON-COATED BOLTS.
GLOBE VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 350 GR LF2; FORGED LOW TEMPERATURE CARBON STEEL BODY; BELLOWS TYPE; BOLTED BONNET; ASTM A 320 GR L7 LIQUID QUENCHED & TEMPERED BOLTING; PTFE GASKET; HASTELLOY C STEM; HARD FACED DISC; HARD FACED SEATING;; BELLOWS, FORMED MULTI-LAYER HASTELLOY C BELLOWS HOLDER, HASTELLOY C; PTFE PACKING; ASME B16.5; POSITION INDICATOR PREPARED FOR CHLORINE SERVICE AT FACTORY; FOR LOW EMISSION SERVICE; FOR CRYOGENIC SERVICE; WARNING I THIS VALVE HAS BALL VALVE FACE TO FACE DIMENSIONS; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. ALL MATERIALS OF CONSTRUCTION TO BE SUITABLE FOR SERVICE TO -50 DEG F. DESCOTE 2100B/BVF
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
00 A 046753 c0/VET0FNTIa !,
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VGL300LC11ARF
SIZE 1 1/2 - 12
VC300AY5AWT
2-12
NOTE <n>
NOTE <n>
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 11 OF 21
DESCRIPTION
GLOBE VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 352 GR LCC; CAST LOW TEMPERATURE CARBON STEEL BODY; BELLOWS TYPE; BOLTED BONNET; ASTM A 320 GR L7 LIQUID QUENCHED & TEMPERED BOLTING; PTFE GASKET; HASTELLOY C STEM; HARD FACED LOW TEMPERATURE CARBON STEEL DISC; HARD FACED SEATING; BELLOWS, FORMED MULTI-LAYER HASTELLOY C; BELLOWS HOLDER, HASTELLOY C; PTFE PACKING; ASME B16.5; POSITION INDICATOR; FOR LOW EMISSION SERVICE; PREPARED FOR CHLORINE SERVICE AT FACTORY; FOR CRYOGENIC SERVICE; ALL MATERIALS OF CONSTRUCTION TO BE SUITABLE FOR SERVICE TO -50 DEG F. WARNING! THIS VALVE HAS BALL VALVE FACE TO FACE DIMENSIONS; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. DESCOTE 2102B/BVF
CHECK VALVE: CLASS 300; RAISED FACE; TAPPED LUG/FLG; ASTM A 351 GR CN7M; ALLOY 20 BODY; WAFER TYPE; DISC ALLOY 20; METAL SEATING; SPRING, INCONEL; ASME B16.5/B16.47 SERIES A; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. GULF MBTL30-X0X7-WRA-710 GULF MBTF3 0-X0X7-WRA-710 MARLIN G30FPF1 (THRD. LUG) MARLIN G30FPF1 (THRD. FLG.) PROQUIP 4QQ102LA PROQUIP 4QQ102FA
VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE.
VALVE TO BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 046754 OONFTDFNTT A!
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VB3 00AY11ARF
SIZE 1-4
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 12 OF 21
DESCRIPTION
VENTED BALL VALVE: CLASS 300/ RAISED FACE; FLANGED; ASTM A 351 GR CN7M; ALLOY 20 BODY; FULL PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; ALLOY 20 STEM; ALLOY 20 BALL; REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; 1 INCH AND UNDER SHALL HAVE ROUND OR OVAL HANDWHEEL; 1 1/4 INCH THRU 4 INCH SHALL HAVE LEVER OPERATOR. WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY "HANDLE FOR INSULATED SERVICE"; VALVE (WITH THE EXCEPTION OF VALVES HAVING PRESSURE RELIEVING SEATS) SHALL HAVE A RELIEF HOLE DRILLED IN THE UPSTREAM SIDE OF THE BALL OR BODY (WHEN THE VALVE IS IN THE CLOSED POSITION) AND A DIRECTIONAL FLOW ARROW PERMANENTLY PLACED ON THE VALVE BODY IN ACCORDANCE WITH THE DOW CHEMICAL COMPANY NORTH AMERICAN BALL VALVE SPECIFICATION N4S-9909-01, LATEST EDITION. THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 6300 KITZ 300 UTBCN KTM EB100 NIBCO 535 WATTS 3800
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
n0 a 046755 /ohfTDFNTT Al
PIPING MATERIAL SPECIFICATION
DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VB300AY12ARF
SIZE 6-8
PIPING SPEC CODE: LX01 DATE: 02-11-94 PAGE: 13 OF 21
DESCRIPTION
VENTED BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 351 GR CN7M; ALLOY 20 BODY; FULL PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; ALLOY 20 STEM; ALLOY 20 BALL; REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; WEATHERPROOF GEAR OPERATOR. VALVE (WITH THE EXCEPTION OF VALVES HAVING PRESSURE RELIEVING SEATS) SHALL HAVE A RELIEF HOLE DRILLED IN THE UPSTREAM SIDE OF THE BALL OR BODY (WHEN THE VALVE IS IN THE CLOSED POSITION) AND A DIRECTIONAL FLOW ARROW PERMANENTLY PLACED ON THE VALVE BODY IN ACCORDANCE WITH THE DOW CHEMICAL COMPANY NORTH AMERICAN BALL VALVE SPECIFICATION N4S-9909-01, LATEST EDITION. THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. KITZ 300 UTBCN KTM EB100 JAMESBURY 6300 NIBCO 535
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VB300CS61ARF
SIZE 1/2 - 4
VB300CS61BRF
6-10
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 14 OF 21
DESCRIPTION
VENTED BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 352 GR LCB; CAST CARBON STEEL BODY; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; HASTELLOY C STEM; HASTELLOY C BALL; PRESSURE RELIEVING REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; 1 INCH AND UNDER SHALL HAVE ROUND OR OVAL HANDWHEEL; 1 1/4 INCH THRU 4 INCH SHALL HAVE LEVER OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01 WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY "HANDLE FOR INSULATED SERVICE"; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5300C
VENTED BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 352 GR LCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; HASTELLOY C STEM; HASTELLOY C BALL; PRESSURE RELIEVING REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; WEATHERPROOF GEAR OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5300C NIBCO 530
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 0467S7 OONFTDFNTTA!
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VBF300AY4AWT
SIZE 3-6
VBF300AY4BWT
8-12
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 15 OF 21
DESCRIPTION
BUTTERFLY VALVE: CLASS 300; RAISED FACE TAPPED LUG; ASTM A 351 GR CN7M; ALLOY 20 BODY; ALLOY 20 (UNS N08020) BOLTING; ALLOY 20 SHAFT; DISC ALLOY 20; REINFORCED PTFE SEATING; PTFE STEM SEALS; PTFE PACKING; BOLTED PACKING GLAND; THROTTLING LOCKING LEVER OPERATOR; THE FINISH OF THE GASKET CONTACT FACES OF THE END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. 8-THREAD SERIES BOLTS ARE REQUIRED WHEN THE FLANGE BOLT DIAMETER IS 1 1/8 INCH OR LARGER; THIS VALVE SHALL NOT BE USED FOR DEAD END SERVICE. SIDE OF VALVE.) DEZURIK BHP,L2,AA,TC,AA-AA-FT-TT,UR*LT
FLOWSEAL 3LA-444RTG-L JAMESBURY 830L-11-3500MT XOMOX 813-0-0-0-ST2-L-X
BUTTERFLY VALVE: CLASS 300; RAISED FACE TAPPED LUG; ASTM A 351 GR CN7M; ALLOY 20 BODY; ALLOY 20 (UNS N08020) BOLTING; ALLOY 20 SHAFT; DISC ALLOY 20; REINFORCED PTFE SEATING; PTFE STEM SEALS; PTFE PACKING; BOLTED PACKING GLAND; WEATHERPROOF GEAR OPERATOR; THE FINISH OF THE GASKET CONTACT FACES OF THE END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5; 8-THREAD SERIES BOLTS ARE REQUIRED WHEN THE FLANGE BOLT DIAMETER IS 1 1/8 INCH OR LARGER; LARGER THAN 24 INCH, FLANGE DRILLING PER ASME B16.47 SERIES A; THIS VALVE SHALL NOT BE USED FOR DEAD END SERVICE. SIDE OF VALVE.) DEZURIK BHP,L2,AA,TC,AA-AA-FT-TT,UR*HD
FLOWSEAL 3LA-444-RTG-3 JAMESBURY 830L-11-3500MT W/MA XOMOX 813-0-0-0-ST2-G-X
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 16 OF 21
ITEM
SIZE
DESCRIPTION
VPN3 00AY4RF
1/2 - 1
PLUG VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 351/A 744 GR CN7M; ALLOY 20 BODY; BOLTED BONNET; ALLOY 20 (UNS N08020) BOLTING; MONEL PLUG; PTFE OR PFA DIAPHRAGM; PTFE SLEEVE; WRENCH OPERATOR. WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY" HANDLE FOR INSULATED SERVICE"; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. DURCO G4 31A-D20/DMM TUFLINE 0367-A20/MO
NOTE <n>
VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE.
******************************************************************************* INSTRUMENTATION
NOTES
N101
N7 033
N7022 N7003 NOTE <n>
THE FOLLOWING SPECIFICATIONS ARE TO BE USED FOR INSTRUMENTATION. FOR ITEMS NOT LISTED, THE PRECEDING PIPING SPECIFICATION IS TO BE USED WHERE APPLICABLE.
INSTRUMENT PIPING IS DEFINED AS THAT PIPING FROM THE FIRST BLOCK VALVE OFF THE PROCESS LINE (NOT INCLUDING THE VALVE) TO THE INSTRUMENT.
ALL SMALL INSTRUMENT CONNECTIONS SHALL BE IN AN EASILY ACCESSIBLE LOCATION.
FLOW (ORIFICE) TAPS:
ORIFICE TAPS ON LIQUID LINES SHALL BE MOUNTED ON THE SIDE. ORIFICE TAPS ON VAPOR LINES SHALL BE MOUNTED ON THE TOP.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
D0 A 046759 OONFTDFNTTA1
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
PIPING SPEC CODE: LI01 DATE: 02-11-94 PAGE: 17 OF 21
ITEM
SIZE
DESCRIPTION
N7302
1/2 IN. SW
TAPS TO ORIFICE FLANGES SHALL BE 1/2" SOCKET WELD.
NOTE <n>
ORFICE PLATES SHALL BE MONEL OR HAST. C CONSTRUCTION, AND MEET OR EXCEED ANSI/API 2530 (A. G. A. REPORT # 3) FOR SHAPE, FINISH, BEVELING AND THICKNESS.
N7004
PRESSURE TAPS:
"NOTE <n>
1 1/2 IN. RFF.
TAP ORIENTATION SHALL BE VERTICAL, TOP OF HORIZONTAL LINE, FOR GAS SERVICE, AND SIDE OF PIPE FOR HORIZONTAL LINES IN LIQUID SERVICE.
NOTE <n>
N7005
N7460
TAPS SHALL BE LINE SIZE ON PIPE SMALLER THAN 1 1/2 INCH.
TEMPERATURE TAPS:
THERMOWELLS SHALL HAVE A MINIMUM 0.26 INCH I.D.
N7402 <n>
1 1/2" SW/RFF
TAP ORIENTATION FOR THERMOWELLS SHALL BE SUCH THAT THE INSERTED WELL FACES AGAINST OR IS PERPENDICULAR TO THE DIRECTION OF FLUID FLOW. THERMOWELLS SHALL BE OF HASTELLOY C CONSTRUCTION.
N7007
OTHER TAPS:
NOTE <n>
NOTE <n>
1-1/2 IN. RFF
ANALYZER TAP ORIENTATION SHALL BE VERTICAL, TOP OF HORIZONTAL LINE.
ALL PROCESS WETTED INSTRUMENTATION COMPONENTS SHALL BE OF THE FOLLOWING CONSTRUCTION:
BODY HALVES OR CASES: HASTELLOY C SENSOR ELEMENTS: HASTELLOY C DIAPHRAGMS: TANTALUM GASKETS: REINFORCED TEFLON O-RINGS AND SEALS: REINFORCED TEFLON SENSOR FILL FLUID: FLUOROLUBE
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
^0 A 046760 CONFIDENT TAI
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE CAUTION
N7025
TUBING PT105
1/4 - 1/2
PIPE NIPPLES PN8
1/2
PN8A
1/2
FITTINGS FT105C
1/4 - 1/2
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 18 OF 21
DESCRIPTION
FOR REMOTE SEAL FLANGED LEVEL APPLICATIONS, USE G39 GASKET ON THE PROCESS WETTED SIDE.
INSTRUMENTS NOT CLOSE COUPLED TO THE PROCESS SHALL BE CONNECTED BY TUBING. IF PIPE IS USED IT SHALL BE 1/2".
TUBING: 0.035 IN WALL; ANNEALED; SEAMLESS; ASTM B 165 (UNS N04400); MONEL 400. HARDNESS NOT TO EXCEED HRB 75, TUBING TO BE SUITABLE FOR BENDING AND FLARING, FREE OF SCRATCHES AND WITH AN EXTERIOR SURFACE THAT HAS A FINISH OF 32 MICROINCH RA. OR BETTER, MEASURED IN EITHER THE LONGITUDINAL OR CIRCUMFERENTIAL DIRECTION, AT ANY POINT ON THE TUBING. OUTSIDE DIAMETER TOLERANCE TO BE -0.0015 INCH AND+0.0045 INCH.
PIPE NIPPLE: BAR STOCK; 0.328 INCH I.D.; EXTRA STRONG WALL ASTM B 165; (UNSN04400); MONEL; 3 INCH LONG; THREADED ENDS. COLLINS INSTRUMENT CO. 133-0003-MON
PIPE NIPPLE: BAR STOCK; 0.328 INCH I.D.; EXTRA STRONG WALL ASTM B 165; (UNSN04400); MONEL; 6 INCH LONG; THREADED ENDS. COLLINS INSTRUMENT CO. 133-0006-MON
TUBING FITTINGS: MONEL. HOKE GYROLOK
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 046761 r.ONFTDFNTTAl,
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM N7021
SIZE
N7001
CAUTION
PC321
E213 T213 FLANGES F28RARF
1/2 - 1 1/2 - 1 1/2 - 1
1/2 - 1 1/2
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 19 OF 21
DESCRIPTION
INTERCHANGING OF COMPRESSION FITTING PARTS OF DIFFERENT MANUFACTURES SHALL NOT BE ALLOWED.
WARNING!
CORRECT ASSEMBLY AND
INSTALLATION OF TUBE CONNECTIONS IS
CRITICAL! SWAGELOK TUBE CONNECTIONS
SHALL BE ASSEMBLED AND INSTALLED AS PER
SWAGELOK INSTALLATION INSTRUCTIONS.
WHEN ASSEMBLY AND INSTALLATION IS
COMPLETE, ALL SWAGELOK TUBE CONNECTIONS
SHALL BE CHECKED AND INSPECTED FOR
PROPER 'PULL-UP/ WITH THE APPROPRIATE
SWAGELOK INSPECTION GAGE. TUBE
CONNECTIONS SHALL INCLUDE FITTINGS AND
VALVES.
PLUG HEX HEAD: THREADED; FORGED; ASTM A 350 GR LF2; SOLID LOW TEMPERATURE CARBON STEEL; ASME B16.ll AND ANSI Bl.20.1 DIMENSIONS. CHARPY TEST AT -50 DEG F.
ELBOW 90 DEG: THREADED; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
TEE: THREADED; CLASS 3000; FORGED; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.ll. CHARPY TEST AT -50 DEG F.
FLANGE: REDUCING; THREADED; CLASS 300; RAISED FACE; ASTM A 350 GR LF2; LOW TEMPERATURE CARBON STEEL; ASME B16.5. CHARPY TEST AT -50 DEG F. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
DO A 04676? CONFTDFNTTAI
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM JOINT COMPOUND
SIZE
JC18
JC15
VALVES VIB2 000AY2
1/2 - 1
VIB2000M08
1/2 - 1/2
VIG6000M01
3/4 - 1/2
VIX6000M02
1/2 - 1/2
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 20 OF 21
DESCRIPTION
JOINT COMPOUND: LIQUID. FLUOROLUBE GR-544
JOINT COMPOUND: TAPE; TEFLON, 3 MIL. FEDERAL PROCESS CO. THRED TAPE FEL-PRO THREAD SEALING TAPE 3M BRAND #48
BAR STOCK BALL VALVE: 2000 PSI @ 100 DEG F; MALE SOCKET WELDING BY FEMALE THREADED; ALLOY 20 BODY; ALLOY 20 STEM; ALLOY 20 BALL; ULTRAFIL SEATING; ULTRAFIL STEM SEALS; ROUND OR OVAL HANDLE. TBV 4161-SWXSE-A2A2-UH
BAR STOCK BALL VALVE: 2000 PSI @ 100 DEG F,*MALE THREADED BY FEMALE THREADED; MONEL BODY; MONEL STEM; MONEL BALL; ULTRAFIL SEATING; ULTRAFIL STEM SEALS; ROUND OR OVAL HANDLE; PREPARED FOR CHLORINE SERVICE AT FACTORY; TBV 4161-SE-M4M4-UT
GAUGE VALVE: CLASS 6000; NPTM BY NPTF (THREE MULTI PORT); ASTM B 164; MONEL ANNEALED BODY; SELF-ALIGNED BALL TYPE; UNION BONNET; MONEL KSOO'STEM; MONEL BALL; INTEGRAL SEATING; PTFE PACKING; ANSI B1.20.1. ANDERSON-GREENWOOD M5VHM-46
TRANSMITTER MANIFOLD ASSEMBLY: 6000 PSI @ 200 DEG F; FLANGED; K MONEL; PTFE' PACKING. VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE. ANDERSON-GREENWOOD M4AVM
LAST UPDATE: 12-16-93 NPL8087
PIPING SPEC CODE: L101
00 A 0467^3 TONF T1 DFNT T Al
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE
NOTE
PIPING SPEC CODE: L101 DATE: 02-11-94 PAGE: 21 OF 21
DESCRIPTION
CONTROL AND AUTOMATED VALVES: CONTROL AND AUTOMATED VALVES SHALL BE OF THE FOLLOWING SPECIFICATIONS: CONTROL VALVES SHOULD UTILIZE LIVE LOADED PACKING AND/OR BELLOW SEAL STEM SEAL, IF POSSIBLE.
CONTROL VALVES (GAS ABOVE -20 DEG. F): TYPE: AS DETERMINED BY APPLICATION BODY: CARBON STEEL TRIM: HASTELLOY C PACKING: LIVE LOADED TEFLON SEALS/GASKETS: HASTELLOY C BELLOW SEAL FLANGE BOLTS: ALLOY 20 (CLEANED & PACKAGED FOR CL2 SERVICE)
CONTROL VALVES (GAS BELOW -20 DEG. F): TYPE: AS DETERMINED BY APPLICATION BODY: CAST 300 SERIES STAINLESS STEEL TRIM: HASTELLOY C PACKING: LIVE LOADED TEFLON SEALS/GASKETS: HASTELLOY C BELLOW SEAL FLANGE BOLTS: ALLOY 20 (CLEANED & PACKAGED FOR CL2 SERVICE)
CONTROL VALVES (LIQUID SERVICE): TYPE: AS DETERMINED BY APPLICATION BODY: CAST 300 SERIES STAINLESS STEEL TRIM: HASTELLOY C PACKING: LIVE LOADED TEFLON SEALS/GASKETS: HASTELLOY C BELLOW SEAL FLANGE BOLTS: ALLOY 20 (CLEANED & PACKAGED FOR CL2 SERVICE)
IF FISHER V500 VBALL VALVE IS USED, THE FOLLOWING MATERIALS ARE ACCEPTABLE
TYPE: FISHER V500 BODY: CAST 300 SERIES STAINLESS STEEL BALL: CHROMIUM PLATED CF-8M (CAST 316) SHAFT: 17-4 PH SS IN THE H1025 OR
SOFTER CONDITION SEAT/RING: 316 SSTL W/STELLITE 6 SEAT PACKING: LIVE LOADED TEFLON FLANGE BOLTS: ALLOY 20 (CLEANED AND PACKAGED FOR CL2 SERVICE)
AUTOMATED (ON/OFF) VALVES: TYPE AND SIZE ARE DETERMINED BY APPLICATION AND SHOULD BE SELECTED FROM THE VALVE SECTION OF THIS SPECIFICATION. THE VALVE SHOULD BE AUTOMATED IN ACCORDANCE WITH
DO A 046764 OONFIDFNTTAI
