Document b5BdqZk60LoLeYo0O3Z5OyVJZ

SEPTEMBER 1959 RATINGS DATA * DIMENSIONS for boilers boilers-hot water supply burners-oil-gas baseboard heating convectors radiators AMERicAN-<$tandard PLUMBING AND HEATING DIVISION 15501 L,- . L t , contents general information boilers gas-fired oil-fired oil or stoker-fired oil, stoker or hand-fired stoker or hand-fired hand-fired hot water supply conversion burners gas oil combustion chambers molded refractory type refractory type baseboard heating cast iron convectors radiators non-ferrous non-ferrous cast iron cast iron boiler selection chart chimneys and drafts G-2 G-4 G-6 orifice drill sizes Arcoleader Arcoliner (wide back) Oakmont A-5 Exbrook Severn A-7 No. 3 Redflash No. 2 Redflash Arcoliner (dry base) direct type C`DW") indirect type ("IS") model IN Inshot Arcoflame Heat Lib-O-Rator made from fire brick model 10 Radiantrim panels model 8 Radiantrim panels Heatrim (models L & H) Multifin Arco Sunrad Arco Peerless page no. 4-5 6-13 14-15 16-19 20-21 22-23 24-25 26-27 28-30 31-32 33-35 36-37 38-39 40 41 42 43 44 45-48 49 50 51-55 56-59 60-63 64-66 67-84 85-87 88-89 90-91 92-93 5-94-96 15502 4 general information fj boiler ratings definition The ratings ("installed radiation sq ft" and "net l = B = R rating for Mbh and sq ft of steam" where shown) of boilers represent the maximum net loads (240 Btu per sq ft steam and ISO Btu per sq ft hot water) that may be connected to the boilers. Allow ances have been made in these ratings for normal piping (covered) and pick-up loads and for heating domestic hot water under the following conditions-. selecting size of boiler In order to select the proper size boiler calculate the heat loss of the building, then divide this figure by 1,000 to get the heat loss expressed in Mbh. Select a steam or water boiler which has a net Mbh rating equal to or greater than this figure using the appropriate steam or water column. For an installation where unusual conditions such as large pipe losses, intermittent heating, unbalanced systems, etc., are encountered, it is suggested to calculate the actual piping loss and estimate the pick-up factor to adjust the load and then select the boiler from the published gross output in Mbh (1,000 Btu per hour). It is not necessary to increase the boiler size for domestic hot water supply when not more than two bathrooms are to be served or if the use of domestic hot water does not exceed seventy-five gallons in twenty-four hours. When more than two bathrooms are to be supplied with domestic hot water or when the demand for domestic hot water exceeds seventy-five gallons in twenty-four hours, increase the boiler size one-half sq ft steam or four-fifths sq ft water for each gallon of storage tank capacity. In the case of oil-fired boilers when Built-in Tankless heater is used, increase the boiler size fifty sq ft steam or eighty sq ft water for each bathroom in excess of two. Sufficient radiation must be installed for the requirements of the building. boilers . . . gas-fired The input and output ratings are approved by the American Gas Association. Ratings shown are for installations at sea level and at eleva tions up to 2000 ft. For elevations above 2000 ft, ratings should be reduced at the rate of 4% for each 1000 ft above sea level. boilers . . . oil-fired The firing rates--(gallons per hour) are based on the use of oil having 140000 Btu per gallon heat value, and with 10% CO? in the flue gas. Ratings shown are for elevations up to 1000 ft above sea level. For elevations above 1000 ft, ratings should be reduced by 4% for each 1000 ft above sea level. When Built-in Tankless Heater is used increase the boiler size 12 Mbh for each bathroom in excess of two. boilers .. . stoker-fired The firing rates (pounds per hour) for i = b = R burner capacity are based on the use of coal having 13000 Btu per pound heat value. Note: The minimum distances between top of stoker hearth and crown sheet should be governed by the following table for the Severn, Exbrook, No. 3 Redflash and A-7 Boilers firing rates Ibs./hr. minimum distance firing rates Ibs./hr. minimum distance 0-20 18~ 41-100 28- 21-30 20- 101-200 30" 31-40 24" 201-300 36" boilers .. . hand-fired The ratings (installed radiation sq ft) are based on the use of stove or nut size bituminous coal, anthracite coal or coke with 13000 Btu per pound heat value. See following table for selecting proper size boiler when using coal with less than 13000 Btu per pound. where coal hat last than 13000 Btu content When selecting hand-fired boilers for burning coal of lower heating value than 13000 Btu per pound, the following correction factors should be used. Multiply the net load by the proper factor and select the boiler with the corresponding rating (installed radiation sq ft). heating value of coal-- BTU par lb 13000 12500 12000 11500 11000 10500 10000 9500 9000 correction factor 1,00 1.04 1.08 1.13 1.18 1.24 1.30 1.37 1.44 when piping lott it negligible The ratings (installed radiation sq ft) of steam boilers (all fuels) and the coal (hand-fired) water boilers may be increased by the percentages shown in the following table when the piping loss of the installation is negligible. The ratings (installed radiation sq ft) of automatic fired water boilers may be increased by 12% when the piping loss of the installation is negligible. installed radiation sq ft steamall fuels watercoal'hand fired up to 250 251-500 501-1000 1001-1500 1501-2000 2001-3000 3001-4000 Over 4000 up to 400 401-800 801-1600 1601-2400 2401-3200 3201-4800 4801-6400 Over 6400 increase ratings bv 30% 28% 24% 21% 18% 15% 13% 12% 15503 1 general information boiler trimmings and sundries Boilers are regularly furnished complete with trimmings and equipment as follows: boilers ... gas-fired Steam: Steam gauge, safety valve, gauge glass and trimmings, resetting low water cut-off, diaphragm gas valve and pressure limit control, draft hood and gas pressure regulator (except for LP-Gas). Water: Theraltimeter, diaphragm gas valve and operating control, draft hood, gas pressure regulator (except for LP-Gas) and relief valve. boilers . . . oil burning, boilers . . . stoker-fired Arcoleader--Arcoliner (wet base)--Oakmont-- Exbrook--A-5--A-7 Boilers specially designed for oil or stoker firing are regularly furnished complete with trimmings, as follows: Steam: Steam gauge, safety valve, gauge glass and trimmings. Water: Theraltimeter and relief valve. Severn--No. 3 Red Flash Regular line boilers adaptable for oil or stoker firing are furnished complete with trimmings and equipment same as corresponding hand fired boilers. Grate assemblies, firing tools and automatic damper regulators are not included. Plate work specially adapt able to installation of oil burner or stoker is supplied. oil heating units Arcoleader--Arcoliner (wet base)--Severn-- Oakmont--Exbrook--A-5 Oil Heating Units Oil Heating Units are regularly furnished complete with trim mings as follows: Steam: Steam gauge, safety valve, gauge glass and trimmings, draft stabilizer. Water: Theraltimeter, draft stabilizer and relief valve. boilers ... hand-fired Arcoliner (dry base)--Severn--Redflash--A~7 Steam: Steam gauge, safety valve, gauge glass and trimmings, automatic damper regulator and firing tools. Water: Theraltimeter, automatic damper regulator (except on No. 3 Redflash), firing tools and relief valve. chimney sizes The use of the correct size chimney is important for proper per formance of the boiler. The chimney provides the draft which burns the coal in hand fired boilers and removes the gases of combustion from automatically fired boilers. If the draft is in sufficient, unsatisfactory operation of the boiler will result. The load the boiler has to carry determines the firing rate and, as stated above, the chimney must be sized to provide the draft conditions required for most efficient performance. The chimney sizes for various boilers and firing methods as listed herein, are suitable when the boilers are selected at their cata logue ratings. They are computed as closely as possible to meet average conditions in lower altitudes that exist in most sections of the country. In higher altitudes it is advisable to increase chimney heights 2% for each 500 feet elevation. external and built-in water heaters external water heaters boiler G-6 A-7 Exbrook No. 3 Redflash bock soetion topping _ Yes Yes Yes intermediate sections with bosses Yes No No Yes These bosses will be tapped on special order. built-in water heaters Tank type built-in water heaters are rated on the basis of raising the temperature of the domestic hot water 100* F. in three hours with a minimum boiler water temperature of 180* F. on auto matically fired boilers and 212*F. on hand fired boilers. Tankless type built-in water heaters are rated in gallons per minute on the basis of a minimum boiler water temperature of 180*F. on oil fired boilers. The maintaining of 180'F. boiler water temperature with rated flow through a tankless type built-in water heater is dependent on the oil firing rate for the boiler. In areas where excessive lime exists in the water, use of built-in tankless type water heater is not recommended except when provision is made for regularly cleaning the heater. Use of tank type water heater is recommended in hard water areas. APPLICATION - RATING - CONNECTIONS name Severn Arcoliner Oakmont Exbrook boiler built-in water heater type how water fired heater type number gals, capacity connec* boiler tion water temp. size TI0* 212* (inches) steam steam or water hand oil or stoker oil or stoker 701 702 703 703 594 S9S tank tank tank tank tank tank 60 1 -- 40 1 - 100 1 66 _ 1 100 _ 1V 160 - 1V4 "t" type oil dry base hand steam only 590 tankless 3V4 per - minute 701 tank _ 60 702 tank - 40 Vr 1 1 wet base oil steam or water (wide back) 597 589 596 steam or oil water 598 599 583 585 597 steam or oil or 591 water stoker 592 tank tankless tankless tank tank tankless tankless tankless tank tank 85 3 per minute 3Vz per minute 40 100 3 per minute ZVz per minute 4V. per minute 120 200 -- -- _ _ -- _ _ _ - 1 V2 V* % 1 Vz Vi % 1V4 IV* "t" type oil 593 tankless 5Vz per _ minute A-S Tankless Heater Ratings are listed on page 29. l=W=H rated built-in tankless water heaters l = W=H rated, large-coil, built-in tankless water heaters specially designed and tested for G-2 Gas Boilers and Arcoleader Oil-Fired Heating Units are rated on the basis of raising the temperature of domestic hot water 100'F (from 40 to 140*) with 200* boiler water temperature. All heaters have l = W=H approved ratings which are obtained by testing the heaters with each size of the boiler. For ratings and data on G-2 tankless heaters, see page 6, Arcoleader tankless heaters, page 22. 15504 ((^.^American-Standard G-2 gas-fired gas boilers water t*wg - forced circulation only flush or deluxe jacket .:r-:-vV*- *T/.y 1`- ''^;] "*'*' factory assembled sections e available packaged in sizes G-23 through G-27 ratings and data tankless heater data (factory installed), for installations at sea level and elevations up to 2000 fta 1=:W=H Rating A-- ' ' boiler number MM. Nat. Mixed, LP-gas or LPAir gat, 525-1400 Btu A.GJt. input A.GUL output Btu/hr. Btu/hr. net t-B-R ratings Btu/hr. net installed ratings sq. ft chimney size height inches feet G-23F 60,000 48,000 36,000 240 4 20 G-24 90,000 72,000 54,000 360 5 20 G-25 120,000 96,000 72,000 480 6 20 G-26 150,000 120,000 90,000 600 6 20 G-27 180,000 144,000 108,000 720 6 20 G-28 210,000 168,000 126,000 840 7 20 G-29 240,000 192,000 144,000 960 7 20 G-210 270,000 216,000 162,000 1080 7 20 G-211 300,000 240,000 180,000 1200 7 20 n For elevations above 2000 ft., ratings should be reduced at the rate of 4% for each 1000 ft above sea level, e G-23 available in flush jacket model only. bailer number A.G.A. input Btu/hr. heater a 222 heater a 22* heater a 232 G-25 120,000 3 __ G-26 150,000 3V* __ G-27 180,000 3V4 4 G-28 210,000 3V4 4y __ G-29 240,000 3V4 4V 4Vi G-210 270,000 3V4 4V 4% G-211 300,000 3V4 4Vz 5 Heaters have been tested with G-2 boilers and are available only factory installed in all models in the above sizes except for the all purpose boilers. e Gallons water per minute heated from 40*F to 140'F with 200"F boiler water temperature. A Last two digits designate lineal feet of Tru Fin tubing in heater coil. For ordering, add following suffixes to regular boiler number: Frr Flush Jacket; D=Oeluxe Jacket; T=Boiler with tankless heater; C = Soiler with floor shield for combustible flooring; P=Packaged. standard equipment packaged and non-packaged boilers American-Standard V-600 combination diaphragm gas valve furnished with G-23-F through G-29 Natural, Mixed, LP-Air, LP gas boilers and G-23-F through G-27 Manufactured gas boilers. V-600 features built-in gas pressure regulator (ex cept for LP Gas) and thermo-couple type safety pilot switch. American-Standard V-S32 diaphragm gas valve furnished for all gases for sizes not listed above with separate gas pres sure regulator (except LP) and Baso switch. Manual shut-off valve; pilot cock; pilot filter (for manufac tured gas and S.U.R.); boiler drain; draft hood, insulated jacket, transformer, ASME relief valve. packaged boilers Junction box. Wiring harness. 1V4~ circulator with piping. packaged boilers, specified WITH tankless heater Tankless heater No. 222. American-Standard RS-116 combination immersion control (high and low limits, circulator operation and built-in relay), CA-412 thermostat. packaged boilers, specified WITHOUT tankless heater American-Standard CA-412 thermostat, American-Standard CA-655 immersion limit control, CA-666-R reverse acting low limit control. Left hand end section without tankless heater opening. Note: Packaged boilers are shipped with jacket, all controls (except thermostat), circulator and piping, main burners and manifold controls and piping factory installed and wired. CA-412 thermostat, manual shut-off valve and relief valve shipped fastened inside boiler crate. Draft hood shipped in separate carton for flush jacketed boiler only. non-packaged boilers, specified WITH tankless heater Tankless heater No. 222. Note: Tankless heater is installed at factory in section assembly. American-Standard RS-116 combination immersion control (High and low limits, circulator operation and built-in relay). non-packaged boilers, specified WITHOUT tankless heater American-Standard CA-655 immersion limit control. Left hand end section without tankless heater opening. optional equipment packaged and non-packaged boilers Runner type pilot ignition for use with listed gases (except for G-23-F or G-23-FP). Floor shield for combustible flooring. Push button electric ignition for use with listed gases. Pilot filter for Natural and Mixed gases. non-packaged boilers Tankless heaters No. 226 or 232; available factory installed in place of No. 222, but limited to certain boiler sizes. See above for l = W = H ratings and applicable boiler size. Floor shield for combustible flooring. Add suffix letter "C" to boiler number. Dual-fuel boilers; available for both natural and LP gases. 15505 gas-fired G-2 gas boilers water Forced, circulation only -flush or deluxe jacket factory assembled sections available packaged'in sizes G-23 through G-27 dimensions -- inlets -- outlets tappings --control applications 2 FLOW -WATER HEATER Z FLOW DRAIN- side view less heater side view with heater leeation tappings on size boiler inches A% B% C% D% E% water immersion limit control temperature and altitude gauge reverse acting control pressure relief valve combination operating, high limit and low voltage relay immersion control .^American-Standard AM forced or gravity circulation factory assembled and'crated. 3 section -- flush jacket only; 4 through 7 section --deluxe jacket Si ratings and data for installations from sea level to 2000 ft. chimney bbiltr numbar A. G. A. input Btu/hr A. G. A. output Btu/hr it an war. IMn a (Mil in. US-I4M la net l = B = R ratines Btu/hr net installed ratings sq. ft site inches G-23-FPG G-24-0PG G-25-DPG G-26-DPG G-27-DPG 60,000 90,000 120,000 150,000 160,000 48,000 72,000 96,000 120,000 144,000 36,000 54,000 72,000 90,000 108,000 240 360 480 600 720 For altitudes above 2000 ft., ratings should be reduced at the rate of 4% for each 1000 ft above sea level. 4 5 6 6 6 height feet 20 20 20 20 20 standard equipment American-Standard V-600 combination diaphragm gas valve furnished with G-23-F through G-27 for all gases. V-600 features built-in gas pressure regulator (except for LP Gas) and thermocouple type safety pilot switch. Manual shut-off valve; pilot cock; pilot filter (for manu factured gas and S.U.R.); boiler drain; draft hood, insulated jacket, transformer; ASME relief valve; CA-655 limit control. optional equipment When boilers (5 through 7 sections) are to be used for forced circulation, l=W=H tankless heaters can be in stalled in opening used for gravity tapping flange cover, but limited to certain boiler sizes. See page 6 for l = W = H ratings and applicable boiler size. Tankless heaters are shipped separately. Runner type pilot ignition for use with listed gases (except for G-23-FPG) furnished when specified on order to meet local Utility codes. Push button electric ignition for use with listed gases, furnished if specified on order. Not available with selfenergizing controls. Self-energizing controls (consist of special gas valve, pilot burner, limit control) for mfd., natural and mixed gas, available if specified on order. Floor shield for combustible flooring. Pilot filter for natural and mixed gases. tappings --control applications side view 3 and 4 section boiler boilers location tappings on size boiler --inehes A y. B y 0 y C y water immersion limit control temperature and altitude reverse acting control pressure relief valve 15507 gas-fired G-2 all-purpose gas boiler packaged water forced or gravity circul craf 3 section -- flush jacket only,-4-through Tsertiorr--deluxe jacket - ------------------ - ....... ....................................--A-~----------------------------- i n i irr 11 dimensions--inlets--outlets boiler numbers of Of sections burners A e dimensions-inches ac size of gas connections--inches (IPS) MM. gas Nat Mxd. D and LP-Air and LP-Air LP gas (523- gas (MO- gas tOO Btu) 1400 Btu) G-23-FPG G-24-DPG G-25-DPG G-26-DPG G-27-DPG 3 4 5 6 7 2 3 4 5 6 ii 16% 19Vb 22% 26% 5% 8X* 9% 11X. 13X. 4 5 5 6 6 n% 19Vi 19% 19 19 % % % % y % % % % Suffix of Model No. indicates number of boiler sections. Example: G-23 boiler has 3 sections. G-27 boiler has 7 sections. Dimensions shown do not include space required for circulator or removal of tankless heater (if used). % Vi Vi % Vi 15508 `jSr/AMERiCAN-^tandard --* ^ "" gas-fired all-purpose gas boiler unpackaged wafer (forced or gravity) or steam N&iy**wsu>* **.-f: '** (a5Vi-' I && factory assembled sections flush or deluxe jdcKet^ J> ^ ^-^%j'-; ratings and data for ins tallations from sea level to 2000 ft bailer number A. G. A. input Btu/hr A. 6. A. output Btu/hr Mfd. Nat Mixed, LP-Gas or LP-Air gas, 529-1400 BtU steam Btu/hr net 1 = 0 = R ratings steam sq. ft water Btu/hr nat insulted rating water sq. ft G-23FG 60,000 48,000 36,000 150 36,000 G-24AG 90,000 72,000 54,000 225 54,000 G-25AG 120,000 96,000 72,000 300 72,000 G-26AG 150,000 120,000 90,000 375 90,000 G-27AG 180,000 144,000 108,000 450 108,000 G-28AG 210,000 168,000 126,000 525 126,000 G-29AG 240,000 192,000 144,000 600 144,000 G-210AG 270,000 216,000 162,000 675 162,000 G-21UG 300,000 240,000 180,000 750 180,000 For altitudes above 2000 ft, ratings should be reduced at the rate of 4% for each 1000 ft. above sea level. G*23 available in flush jacket model only. A Substitute letter "F" for flush or "DM for deluxe jacket 240 360 480 600 720 840 960 1080 1200 chimney - size inches height 4 20 5 20 6 20 6 20 6 20 7 20 7 20 7 20 7 20 | For ordering, add following suffixes to regular boiler number: F = Flush Jacket; 0 = Deluxe Jacket; C = Boiler with floor shield for comoustibk flooring; G:= all-purpose. standard equipment water and steam boilers American-Standard V-600 combination diaphragm gas valve furnished with G-23-F through G-29 Natural, Mixed, LP-Air, LP gas boilers and G-23-F through G-27 Manufactured gas boilers. V-600 features built-in gas pressure regulator (ex cept for LP Gasl and thermocouple type safety pilot switch. American-Standard V-532 diaphragm gas valve furnished for all gases for sizes not listed above with separate gas pres sure regulator (except LP) and Baso switch. Manual shut-off valve; pilot cock; pilot filter (for manu factured gas and S.U.R.); boiler drain; draft hood, insulated jacket, transformer. water boilers only Theraltimeter. ASME relief valve. American-Standard CA-655 immersion limit control. steam boilers only Steam gauge. Safety valve. American-Standard 450-BA-l boiler pressure limit control. External resetting'low water cut-off. optional equipment water and steam boilers Self-energizing controls (consist of special gas valve, pilot burner, limit control) for mfd., nat. and mixed gas, available when specified on order. Runner type pilot ignition for use with listed gases (except G-23-FG) furnished when specified on order to meet local Utility codes. Push button electric ignition for use with listed gases. Specify on order. Not available with self-energizing controls. Floor shield for combustible flooring. Add suffix letter "C" to boiler number. Oual-fuel boilers are available for both natural and LP gases. Pilot filter for natural and mixed gases. water boilers only When boilers (5 through 11 sections) are to be used for forced circulation, l = W=H tankless heaters can be in stalled in opening used for gravity tapping flange cover, but limited to certain boiler sizes. See page 6 for I = w= H ratings and applicable boiler size. Tankless heaters are shipped separately. steam boilers only No. 101 Electric Water Feeder for use with No. 67 Low Water Cut-off to provide Low Water Cut-off and Feeder Combination. side view front view location tappings on size boiler -inches water steam A 44 immersinn limit control - s 44 temperature and altitude pressure gauge gauge c % reverse acting control - D % pressure relief valve safety valve E 3 gravity flow blow-off 15509 dimensions inlets outlets .1 all-purpose gas boiler unpackaged wafer (forced or gravity) or steam factory assembled sections flush or deluxe jacket dimensions-inches size of ges connections--inches (IPS) boiler numbers number number of of sections burners A flush B flush EF flush flush c A deluxe B deluxe Mfd.ges Nat Mxd. 0 and IP-Air and LP-Air LP dual fuel deluxe gas (MS- gas (M0- gas MO Btu) 1400 Btu) natural propane G-23-FG 3 2a 5% 13 74 _---- % % %% % G-24AG 4 3 14Vi 7% 13% 7 5 16% BK< 19% % % %% % G-25AG 5 4 17% 8% 13% 7 5 19% 9% 19% % % %% % G-26AG 6 5 20% 10% 16% 9 6 22% UX. 19 % % % % Vi G-27AG 7 6 24 12 16% 9 6 26% 13X. 19 % % %% % G-28AG 3 7 27V4 13% 20% 12 7 29% 14% 19% i % % % Vi G-29AG 9 8 30% 15% 203/4 12 7 32% 16X. 19% i % %% % G-2I0AG 10 9 333/1 16% 25% 16 8 35% 17% i9y. i % % % Vi G-211 AG 11 10 37 18% 25% 16 8 39% 19X. 19% i % % % Vi Suffix of Model No. indicates number of boiler sections. Example: G-23 boiler has 3 sections. G-211 boiler has 11 sections, Dimensions shown do not include space required for circulator or removal of Tankless heater (if used). A Substitute letter "F'* for flush or "0" for deluxe jacket. 15510 All G-2 Boilers are AGA approved for installation with mini mum clearance from adjacent combustible surfaces. This approval is based on tests which insure that temperatures of adjacent combustible surfaces will not be excessive when the boiler is installed in a closet type enclosure with the specified minimum clearances. Provisions for ready access to the unit for adjustment, repair and replacement of parts take precedence over the clearances shown in table below. With the closet door open there must be a minimum front clearance of 18 inches. V B deluxe jacket NOTE: area of each opening -- 1 sq. in. for each 1,000 Btuh input with a minimum of 100 sq. inches. EL ER top view D s S s V s designation symbol minimum clearance -- inches G-24D thru G-2110 from top of boiler from front of boiler from flue from back of boiler from left side from right side A B C D EL ER 24 6 6 2 0 0 Approved on non-combustible floor and on combustible floor when equipped with bottom pan and radiation shield. 15511 ,. f.r.-.a:.-", v?'. ' . 'x .-Z gas-fired approved closet installation reduced clearance) Mlall G-2 boilers water or steam (for use with city gases only All G-2 Boilers ere AGA approved for installation with mini mum clearance from adjacent combustible surfaces. This approval is based on tests which insure that temperatures of adjacent combustible surfaces will not be excessive when the boiler is installed in a closet type enclosure with the specified minimum clearances. Provisions for ready access to the unit for adjustment, repair and replacement of parts take precedence over the clearances shown in table below. With the closet door open there must be a minimum front clearance of 18 inches. flush jacket NOTE: area of each opening - 1 sq. in. for each 1.000 Btuh input with a minimum of 100 sq. inches. top view minimum clearance -inches designation symbol G-23 G-24 G-23 G-25 G-27 6-21 G-29 from top of boiler from front of boiler from flue *rom back of boiler `rom left side `rom right side A 56V2 56y2 56V2 56Vz 56V2 56V2 56V2 B6 6 6 7 7 8 8 C6 6 6 6 6 6 6 D2 2 2 2 2 2 2 EL 5 4 2 2 1 1 1 ER 5 4 2 2 0 0 0 Approved on non-combustible floor and on combustible floor when equipped with bottom pan & radiation shield. G-210 56y2 9 6 2 1 0 G-211 56V2 9 6 2 1 0 ^American-Standard G-4 gas boilers water or steam jacket encloses all controls ratings and data for installation at see level and elevation! up to 2000 ft A.SUL input A.G.A. output net 1 = B = R rating net installed rating number Btu/hr Btu/hr Mfd., Nat, Mixed and LF-gas; IP-Air gae-S29*l400 Btu team Btu/hr sq.ft. water Btu/hr water sq. ft G-44 G-45 G-46 G-47 G-48 G-49 G-410 G-411 180,000 240,000 300,000 360,000 420,000 480,000 540,000 600,000 144,000 192,000 240,000 288,000 336,000 384,000 432,000 480,000 108,000 144,000 180,000 216,100 252,100 288,100 324,100 360,100 450 600 750 900 1050 1200 1350 1500 108,000 144,000 180,000 216,100 252,100 288,100 324,100 360,100 720 960 1200 1440 1680 1920 2160 2400 For altitudes above 2000 ft., ratings should be reduced at the rate of 4% for each 1000 ft above sea level, The ratings of these boilers represent the maximum net loads that may be connected to the boilers. Allowances have been made for normal piping and pick-up loads. chimney size diameter, inches 6 7 7 8 8 9 9 10 height feet 20 20 20 20 20 20 20 20 minimum piping recommendations for G-4 gas boilers number, size and location of outlets boiler size steam no. size water no. size boiler also steam no. size water no. size G-44 i 2- G-45 i G-46 i 3" G-47 i 3" * (NJ i IV* i 1Vi* i lVz* i 2- G-48 2 2Vi" G-49 2 2V4" G-410 2 3" G-411 2 3" i i i i 2" 2Vi" 2Vi" 2Vi" Note: Either right or left hand supply outlet may be used on water bolters using circulators, but limit control should be placed in that section carrying the supply outlet being used. On gravity circulation use both outlets of sizes shown above. standard equipment STEAM BOILERS: Diaphragm gas valve: Baso automatic pilot switch for non-100% safety shutoff. (For 100% safety shutoff for LP and LP-air gases, Baso combination pilot switch and valve with auxiliary Baso pilot valve. Optional on other gases.) Resetting low water cut-off; boiler pressure limit control; manual shut-off valve; pilot filter (for mfd. gas and SUR.) and gas pressure regulator (except for LP gas); steam gauge, safety valve; boiler drains and pilot cocks; drafthood; insulated jacket. WATER BOILERS'. Diaphragm gas valve; Baso automatic switch for non-100% safety shutoff. (For 100% safety shut off for LP and LP-air gases, Baso combination pilot switch and valve with auxiliary Baso pilot valve. Optional on other gases.) Immersion limit control; manual shut-off valve; pilot filter (for mfd. gas and SUR.) and gas pressure regu lator (except for LP-gas); theraltimeter-, boiler drains and pilot cocks; insulated jacket; drafthood; relief valve. optional equipment Electronic controls; non-100% safety shutoff manual igni tion; non-100% safety shutoff with electric ignition; 100% safety shutoff with electric ignition. 47-2 McDonnell and Miller combination low water cutoff and feeder. 67-AR McDonnell and Miller external type low water cutoff. American-Standard V-532 diaphragm gas valve. Push button electric ignition for mfd., nat. and mixed gases non-100% shutoff. Pilot filter for nat. and mixed gas. All sizes of G-4 are available with Runner type pilot ignitor for mfd., nat. and mixed gas non-100% shut-off, if specified to meet local Utility codes. instructions for ordering G-4 and 0-6 gas boilers (1) For G-4 and G-6, specify for Steam or Water. (4) Btu (Heat Value of Gas) and Specific Gravity. (2) Equipment desired; Regular or "IS." (5) Elevation at point of installation if in excess of 2,000 ft. (3) Type of Gas. (If LP-Gas, whether Butane or Propane.) (6) Pressure available at outlet of Gas Meter. 15513 dimensions -- inlets -- outlets rcmn I gas-fired .1" G-4 gas boilers water or steam r -V - % , lacket encloses all controls number dimensions--inches sin of fas connections (IPS) boiler of number numbers flue of outlets burners A B c Mfd Gas and Nat, Mixad and 0E F6 H L LP-Air gas LP-Air gas LP-gas (S29-800 Btu) (800-1400 Btul G-44 G-45 G-46 X I 1 3 14Vi 13 9% 6 5 8% n% 16 20% 4 18Vi 17 13% 7 5% 9% 12% 20 24% 5 22Vi 21 17% 86 10% 13% 24 28% % 1 1 %% % Vz %% G-47 G-48 G-49 G-410 G-411 1 1 1 1 1 6 26y2 25 21% 9 6% 11% 14% 28 32% 7 30Vi 29 25% 9 6% 11% 14% 32 36% 8 34% 33 29% 10 7 12%. 15% 36 40% 9 38% 37 33% 10 7 12% 15% 40 44% 10 42% 41 37% 11 7% 13% 16% 44 48% m i% i% iy i% i% i% i% i% % iv % I Suffix of Model No. indicates number of boiler sections. Example: G-44 boiler has 4 sections. tappings -- assemblage of sections CONTROL TAPPINGS boiler no. of sections number left center right G-44 i 2 i G-45 i 3 i G-46 i 4 i G-47 i 5 i G-48 i 6 i G-49 i 7 i G-410 i 8 i G-411 i 9 i 15514 >J)Am e rican -^Standard ratings and data number far installations at sea level and elavatiens up to M00 ft a Mfd, Nat, M ixed, LP-Gas or IP-Air ns S2S-1400 BtU Not l = B=R rating A.GJI. input Btu/hr A.G.A. output Btu/hr sts am Btu/hr sq. ft water Btu/hr not installed rating water sq. ft G-66 G-67 G-68 G-69 G-610 G-611 G-613 G-615 G-617 G-619 G-621 G-622 G-625 G-628 G-631 G-633 G-637 G-641 650,000 780,000 910,000 1,040,000 1,170,000 1,300,000 1,560,000 1,820,000 2,080,000 2,340,000 2 600,000 2,'/ 30,000 3,120,000 3,510,000 3,900,000 4,160,000 4,680,000 5,200,000 520,000 624,000 728,000 832,000 936,000 1,040,000 1,248,000 1,456,000 1,664,000 1,872,000 2,080,000 2,184,000 2,496,000 2,808,000 3,120,000 3,328,000 3,744,000 4,160,000 390,100 468,100 546,100 624,200 702,200 780,200 936,200 1,108,100 1,282,000 1,452,300 1,614,900 1,695,700 1,937,900 2,180,100 2,422,400 2,585,400 2,903,700 3,229,800 1625 1950 2276 2601 2926 3251 3901 4617 5342 6051 6729 7065 8075 9084 10093 10773 12099 13458 390,100 468,100 546,100 624,200 702,200 780,200 936,200 1,108,100 1,282,000 1,452,300 1,614,900 1,695,700 1,937,900 . 2,180,100 2,422,400 2,585,400 2,903,700 3,229,800 2600 3120 3640 4160 4680 5200 6240 7385 8545 9680 10765 11305 12920 14535 16150 17235 19360 21530 For altitudes above 2000 ft., ratings should be reduced at the rate of 4% for each 1000 ft above sea level. The ratings of these boilers represent the maximum net loads that may be connected to the boilers. Allowances have been made for normal piping and pick-up loads. chimney size diameter-inches hoicM-fOot u 20 12 20 13 20 13 20 14 20 15 20 15 20 16 20 16 30 17 30 18 30 19 30 20 30 21 30 22 30 24 30 26 30 26 30 minimum piping recommendations for G-6 gas boilers boiler site G-66 G-67 G-68 G-69 G-610 G-611 G-613 G-615 G-617 G-619 G-621 G-622 G-625 G-628 G-631 G-633 G-637 G-641 R.H. end saction 1--4* 1--4* 1--5* 1--51--51--5- -- -- 1--6" 1--61--6- -- -- -- -- -1-- -- -- steam L.H. end section ___ -- -- -- ___ -- -- -- 1--61--61--6- -- -- -- -- ___ ___ -- number, site and location of outlets Intermediate section -- -- -- -- -- 1--61--6" -- -- -- 2--6* 2--62--6* 2--63--63--63--6* R.H. end section 1--2Vi1--2Vi" 1--31--31--41--41--41--41--51--51--5- -- -- -- -- -- -- -- water L.H. end saction -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Intermediate section -- -- -- -- -- -- -- -- -- -- 2--5* 2--52--5" 2--53--5* 3--53--5" .H a w a ii) "hiii jjg p p q w iW W W i standard equipment STEAM BOILERS: Diaphragm gas valve; Baso automatic pilot switch for non-100% safety shutoff. (For 100% safety shutoff for LP and LP-air gases, Baso combination pilot switch and valve with auxiliary Baso pilot valve. Optional on other gases.) Boiler pressure limit control; resetting low water cut-off; manual shut-off valve; pilot filter (for mfd. gas and SUR.) and gas pressure regulator (except for LPgas); steam gauge; safety valve; boiler drain and pilot cocks; drafthood; insulated jacket. WATER BOILERS: Diaphragm gas valve; Baso automatic pilot switch for non-100% safety shutoff. (For 100% safety shutoff for LP and LP-air gases, Baso combination pilot switch and valve with auxiliary Baso pilot valve. Optional on other gases.) Immersion limit control; manual shut-off valve; pilot filter (for mfd. gas and SUR.) and gas pressure regulator (except for LP-gas); theraltimeter; boiler drains and pilot cocks; insulated jacket; relief valve; drafthood. optional equipment Electronic controls: non-100% safety shutoff manual igni tion; non-100% safety shutoff electric ignition; 100% safety shutoff with electric ignition. 47-2 McDonnell and Miller combination low water cutoff and feeder for G-66 through G-611 steam boilers and 51-2 combination for G-613 through G-641 steam boilers. 67-AR McDonnell and Miller external type low water cutoff. American-Standard V-532 diaphragm gas valve. Push button electric ignition for mfd., nat. and mixed gases non-100% shut-off. Right hand end steam trim tappings. Pilot filter for nat. and mixed gas. (See instructions for ordering G-6 Boilers on page 14 under G-4 Boilers). 15515 gas-fired G-6 T'* v.* gas boilers water or steam ?r~. ?'i T.. 51y jadntd -Yi boiler numbara number of flue outlets number of burners A dimensions-inehes B c l siza of gas connaelion* (IPS) Mfd. Gas and LP-Air gas (323*400 Btu) Nat, Mixed and LP-Air gas (400*1400 Btu) G-66 G-67 G-68 G-69 G-610 G-611 G-613 G-615 G-617 G-619 G-621 G-622 G-625 G-628 G-631 G-633 G-637 G-641 i i i 2 2 2 2 2 4 4 4 3 6 6 6 a 8 8 5 _ -- 6% 6 ___ -- 6% 7 -- -- 6% 8 -- -- 6% 9 -- -- 6% 10 ___ -- 6% 12 3m ___ 6% 14 35% -- to 16 39% -- 8% 18 43% -- 8% 20 47% ___ 8% 21 35V* 35V* 8% 24 39% 39% 8% 27 43% 43% 8% 30 47% 47% 8% 32 39% 39V. 8% 36 43% 43% 8% 40 47V* 47% 8% 27% 31% 35% 39% 43% 47% 62V* 70% 78% 87 95% 105% 118 130% 142V* 157% 173% 190% i% 2 2 2 2 2 2% 2% 2% 3 3 3 3 3 2-2% 2-2% 2-3 2-3 IV* 1% IV* 1% 1% 1% 2 2 2 2% 2% 2% 2% 3 3 3 3 3 Suffix of Model No. indicates number of boiler sections. Example: G-622 boiler has 22 sections. G-66 through G-641 are approximate sizes only. LP-gas i% IV* 1% 1% IV* 1% 2 2 2 2% 2% 2% 2% 3 3 3 3 3 ^^^AMEHicAy-<$tandard 15516 18 gas-fired EL,'?,.: jacketed G-6 gas boilers water or steam tappings -- assemblage of sections An outstanding feature of larger G-6 Boilers is the number of flow tappings provided. For example, types G-613 to G-621 have three 6* types G-622 to G-631 have four 6', types G-633 to G-641 have five 6' flow tappings. Their use slows steam velocity and helps prevent entrainment of water. Illustrated below are typical section assemblies of the G-6. The drawings show the flow and return tappings of the G-633. 1'electric limit CONTROL TAPPINt 24* LOW WATER CUT-OFF TAPPIN 4'control * TAPPING side view left hand end section boiler number G-66 G-67 G-68 G-69 G-610 G-611 G-613 G-615 G-617 G-619 G-621 G-622 G-625 G-628 G-631 G-633 G-637 G-641 no. of sections intermediatee -- centers 4 --5 --6 --7 --8 --9 1 10 1 12 1 14 1 16 1 18 2 18 2 21 2 24 2 27 3 28 3 32 3 36 E 25 29% 33% 37% 41% 45% 60Ve 68% 76% 87% 93Ve 103% 115% 128% 140% 155% 171% 188% F 27 31% 35% 39% 43% 47% 62% 70% 78% 86% 95% 105% 117% 130% 142% 157% 173% 190% G -- -- -- --* -- -- 31X. 35X* 39X. 4356 47X. 35X. 39Xi 4356 47X. 39X. 43X. 47X. H -- -- -- -- -- -- -- -- -- -- -- 35Ve 39% 43% 47% 39% 43% 47% Each G-6 boiler section assemblage includes one right-hand end section and one left-hand section in addition to the sections shown in this table. 15517 dimensions for draft hood outlets I t------ r --A* 1 4 1r 6*7-1 sections h------- L--------- 9-10-11 sections I------------- L--------13-15 sections -A. --C -- rc- A* -B- -B- *0- 1 1 F1 f --------- r 4 * 4 AH --c-- --C-- --C-- -A-8- -B* -B- -B- 1 w1 f1 t 4 4 4 4 i--------r L---------------------- - 29-21-31 sections 33-37-41 sections no. of sections 67 no. of flue outlets 1 1 1 9 10 11 13 IS 17 1 21 22 29 2S 31 33 37 41 12 2 22 24 4 43 1 0 1 S1 A 13'/* 15% 17% 12% B -- -- -- 14 C -- -- ---- L 27% 31V. 35% 39% minimum equivalent diameter of flue header 14 13% 13% 16 20 ---- 43% 47% 16 16 15% -- 31 62% 18 17% 12% -- 14 35% 25% 70% 78% 18 20 13% 13% 17% 12% 13% 13% 12% 13% 13% 16 20 -- 14 16 20 14 16 20 27% 27% 35% 25V* 27% 27% 25V* 27% 27% 87 95% 105% 118 130% 142% 157% 173% 190% 20 22 22 24 24 26 26 30 30 15518 ^Sj)AMERiCAN-<$tandard -fired orifice drill sizes-- main burner spuds SSffig 4*;;': -:'V 430 B tuo sea high sea high level a ltitu d e level a ltitu d e B tu /5c2u5. ft. i/9 "O a3. (A h. 0c) 3 _Q C D E v> 0) N Mi a> u <c in p u t per orifice B tu/hr sea h ig h level a ltitu d e in p u t per orifice B tu/tu sea level 1 18 1 1 525 B tU B gf 3 S N3 a elgs 3 3n *3u** s irB IB SS5 ; *** B * CD S?2 f *< o B2 t5u00a B2t0u5o0 24,000 24,000 24,000 2.00 1.53 1.16 II 2 1 1 1 S 1 II ISM II Sllll S1 1 1 30,000 30,000 30,000 41 31 39 23 31 32 39 39 4 1 1 1 sea level 1100 B tu a 1200 B tu/cu. ft. 41 mB3IsASs* *5IB *25 sea level 1200 B tua 1100 B tu/cu. ft. i III 2fl o Ma2mSa O3 3" *2* *5 3 s oA0 ssU.' 3 a V>A3 Stn3-s. NVqI ) >32 -<3 S"i high sea a ltitu d e level 450 00 Btuo B tua I 25 2 6 > 23 0-40 27 28 28 0.50 G-2 30,000 27,000 0.60 0.65 20 23 0.70 20 20 31 31 37 37 39 39 0.40 8 0.50 4 G-4 60,000 55,000 0.60 2 0.65 0.70 1 60,000 60,000 60,000 48,000 48,000 48,000 2.00 1.53 1.16 44 18 18 27 17 16 25 29 29 1 1 N II 1 1 1 1 13 1 I 1 51 1 1 1 31 1 1 1 1 iS 1R r- fn M | i i- i 27 27 130,000 110,000 2.00 130,000 110,000 1.53 130,000 110,000 1.16 oro S9'0 090 090 OV'O 11*11 1 11 1 1 1 | | ia i i i S1 1 1 1 5i i i i -t Su Jc2 3C t~ E S! '*1 IIIIs9"-.? 5 1 2 * 6 T5 S82 G 6 130,000 1 12 1* i r i i i * i n i i*i* 1 1" 1Q 1 1 O | u. * * * 1 a* 2x 1O * 1 1 | ooo 2 <o -- o I I CD 4 (0A0 (I0BA0 (2Q<8v 4i o C 41 in .2 ~ -o S^ c% 11: Is 3a ^ <a wo 'cO SS gSs Ss" 2 38B'n SOw-S * si u 4> * Si* a 03* 1A c _ O4> V41) <AA IB ^C " g <B |2 s OOw^^ Elf M>.w > C"JO ib 5 * Sj > > oo i* i X i;s*g Up*DCS a?5 5 s 5> 4> S> u -O 3 = 5 VI 3 v a O -- o ;o $ r o 5o -Mi1 a * Z 5 5 * * 4* 3 o2 0c0 s 23* 4A) Io/I (oA IvA (S'?4>,I 3nuCuCu^u= rr -- J 4ICCCC N > ^AlflOO S 5 < <;.; a"k. tI4oB1 CO i ok. b o ile r number 15519 ^ MWA wa 11"\ n I conversion burners orifice drill sizes-- inshot main burner spuds ;V ' - ry. V Btu/cu ft 520 550 600 750 MO 900 1000 1050 1100 specific gravity 0.40 o.so 0.60 0.63S 0.65 OiS 0.65 0.65 0.65 Input Btu/hr orific. tin 80,000 90,000 95,000 100,000 110,000 120,000 130,000 140,000 150,000 160,000 170,000 180,000 190,000 200,000 210,000 220,000 230,000 240,000 250,000 260,000 275,000 % V. c 2 8 V. H F 'X. 4 F i G C X. G K H Vi X. J 'X. j G A L X. M 1 B N' p N X. Vi X. Q 0 L F p R QM 1 -- -- ---- J -------- -------- -------- L M N -- -- -- -- X. -------- p ---- -- -- Q -------- R ---- ---- R ------ -- S ------ -- T ------ - U 12 16 17 18A 7 X. 13 15 5 10 11 130 4 10 9 13 25 58 1 3 46 C1 2 X. 0A 12 GC BA GD DB J F ED J G F V. M 1 HG LJ iH X. L j J NMK K 0 N 'X. L P NM L Q X. N N R X. X. % S%P 0 Note: Orifice sizes are based on 2V?' manifold pressure for gases having a heating value less than 800 Btu./cu. ft., and 31/2" manifold pressure for gases having a heating value of 800 or more Btu./cu. ft. Minimum orifice size for IN-1 SO for Natural gas Minimum orifice size for IN-245 and IN-275 for Natural gas Minimum orifice size for IN-150 for Manufactured gas For Philadelphia Gas Works 15520 rVAm e rican-Standard BOILERS I oil-fired \ * . '$k$$h': r^'Su. ^ Arcoleader packaged oil heating units boiler-burner units boilers water only wet base construction ; V/" ratings and data boiler number net l = B = R rating Btu/hr net installed rating sq. ft gross l=B=R output Btu/hr l=B=R burner capacity gph size inches chi nney height feet packaged oil heating units Al-3-P(T) Al-4-P(T) Al-5-P(T) 75,000 102,000 129,300 500 100,000 .95 680 136,000 1.30 865 173,000 1.65 8x8 8x8 8x8 15 15 15 boiler-burner units Al-3-B(T) Al-4-B(T) Al-5-B(T) A1-6-BCD AI-7-B(T) 75,000 102,000 129,800 156,000 183,000 500 680 865 1040 1220 100,000 136,000 173,000 208,000 244,000 .95 1.30 1.65 1.95 2.30 8x8 8x8 8x8 8x8 8x 12 15 15 15 15 15 boilers A1-3(T) A1-4(T) A1-5(T) A1-6CD A1-7(T) 75,000 102,000 129,800 156,000 183,000 500 680 865 1040 1220 100,000 136,000 173,000 208,000 244,000 .95 1.30 1.65 1.95 2.30 8x8 8x8 8x8 8x8 8x 12 15 15 15 15 15 Nozzle sizes, gph, urnished with Arcoleader oil heating units: Al-3, 0.90-60* or 70* H; Ai-4, 1.25-60* or 70* H; Al-5, 1.50-60* or 70* S; Al-6, 1.75-60* or 70* S; Al-7, 2.00-60* or 70* S. The ratings tor these boilers represent the net loads that may be connected to the boilers. Allowances have been made for normal pip<ng and pick-up loads. Note: suffix "P" denotes oackaeed unit. Suffix boiler-burner unit (non-paekaged). "T" denotes with tankless heater. Numeral in suffix indicates number of sections.* Example A1-3-P has 3 sections. tankless heater data unit or boiler number l=B=R burner capacity gph heater 723 e 1 = W -= H rating heater 732# heater 743 e A1-3 .95 3vx 3Ya -- Al-4 1.30 3Vi 4Vi -- Al-5 1.65 3Vi 4V4 5Vz Al-6 1.95 3yx 4Vi 6 Al-7 2.30 3Vi 4Vi 6 a Gallons of water per minute heated from 40*F to 140`F with 200*F boiler water temperature. Last two digits designate lineal feet of Tru Fin tubing in heater coil. Heater 732 furnished as standard equipment with A1-3-T and A1-4-T; heater 743 furnisned as regular equipment with A1-5-T through A1-7-T. standard equipment (packaged units) Model PH2-5 Arcoflame oil burner with hanger mounting for front firing. American-Standard CA-701 stack control fac tory installed. Draft stabilizer. ASME relief valve. Open top heat Lib-O-Rator high temperature steel combustion cham ber. Flush jacket. 1V4" circulator with piping. Wiring harness. Drain valve. Packaged units for forced circulation with fac tory installed tankless heater: Unit numbers A1-3-PT and A1-4-PT: Built-in tankless heater No. 732. Unit number A1-5-PT: Built-in tankless heater No. 743. No. 36 Arcoflame control set (American-Standard CA-412 thermostat, CA-610 combination immersion control consists of; high and low limits, circulator operation and built-in relay) and nozzle. Packaged units for forced circulation less tank less heater: No. 23 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard CA-655 immersion limit control, CA-666-R reverse acting low limit control) and nozzle. Heater opening cover plate. Note: Units are shipped with flush jacket, all electrical con trols (except thermostat), circulator and piping, factory in stalled and wired. PH2-5 Arcoflame oil burner -- shipped separately. Draft stabilizer, relief valve, and CA-412 thermostat are secured inside boiler crate. optional equipment: Jacket extension; if desired specify on order. Jacket exten sion, shipped in separate carton, provides lSVx" enclosure in front for concealment of oil burner and controls; ap proximate shipping weight 35 lbs. Two-stage fuel unit will be furnished when specified on order. standard equipment (boiler-burner units) Same equipment as packaged units less the following; 1V4" circulator with piping. Wiring harness. Drain valve. units for forced circulation specified with fac tory installed tankless heater: Unit numbers A1-3-BT and A1-4-BT: Built-in tankless heater No. 732. Unit number A1-5-BT thru A1-7-BT: Built-in tank less heater No. 743. Note: Tankless heaters are installed at factory in section assembly. Same controls as packaged units for forced circulation. units for forced circulation specified less fac tory installed tanfcfess heater: Same equipment and controls as packaged units for forced circulation less factory installed heater. optional equipment: Same jacket extension as packaged units. Built-in tankless heaters can be ordered for separate ship ment with units less factory installed tankless heater. Arcoflame control sets other than those included above will be furnished when specified on order. (See current price books.) Two-stage fuel unit will be furnished when specified on order. Motors and controls regularly furnished with Arcoleader units are for 115 volt, 60 cycle current. standard equipment (boiler only) Flush jacket, ASME relief valve, factory-installed open top steel combustion chamber and tankless heater, if specified on order. optional equipment: Jacket extension; water heater cover plate (can be speci fied tapped 3" for gravity installations); built-in tankless heaters available for separate shipment. ; -; { t 4 4 15521 dimensions--inlets--outlets oil-fired Arcoleader packaged oil heating units boiler-burner units boilers water only boiler number number and size of tippings--inches flow ratum Al-3 Al-4 Al-5 A1-6 Al-7 1-1V2 1-1% 1-1% 1-1% 1-1% 2-1% 2-1% 2-1% 2-1% 2-1 Vi dimensions--inches L A B c flush jackal jaeket extension 11 Vi 16Vi 21% 26% 31% 8Vi 10% 13% 15% 18% 6 7 7 8 9 16% 21V* 26Vi 31% 36V* 32 37 42 47 52 side view-extended jacket cutaway thru boiler sections assemblage of sections oil heating unit number Al-3 Al-4 Al-5 Al-6 Al-7 arrangement of sections F,C, B F, C, C, B F, C, C, C, B F, C, C, C, C, B F, C, C, C, C, C, B Code: F-Front connecting section C-Center Section B-Back section 'cttons for Arcoleader shipped assembled. toppings -- control applications location size on boiler inches D y E% F% G% water control relief valve combination immersion control for installations with tankless water heater limit control combination altitude gauge and thermometer immersion control, reverse H % acting for installations without tankless water heater ij flow o American-Standard 15522 24 Arcofiner wide back type oil boiler-burner units boilers water or steam factory assembled sections wet baser flush jacket arranged for, but less, built-in tank or tankless type wafer heater ratings and data boiler number a steam ! water net l=B=:R rating steam Btu/hr tq ft water Btu/hr net inatallad rating water sq ft frees l-B--R output Btu/hr l=B=R capacity gph chimney size inchai heigh feet oil heating units S-0-153-8-T W-0-153-B-T 72,800 303 72,800 485 97,000 S-0-154-8-T W-0-154-B-T 99.000 413 99,000 660 132,000 S-0-155-B-T W-0-15S-8-T 123,000 513 123,000 820 164,000 S-0-156-8-T W-0-156-B-T 141,000 588 141,000 940 188,000 1.00 1.35 1.60 1.80 8x8 8x8 8x8 8x8 20 20 25 25 oil-fired boilers S-O-153-T W-0-153-T 72,800 303 72,800 485 97,000 1.00 8x8 20 S-0-154-T W-O-154-T 99,000 413 99,000 660 132,000 1.35 8x8 20 S-0-155-T W-0-155-T 123,000 513 123,000 820 164,000 1.60 8x8 25 S-0-156-T W-0-156-T 141,000 588 141,000 940 188,000 1.80 8x8 25 Three smelter sizes equipped with Crown Sheet Baffle. When furnished less Arcoflame Oil Burner, it is recommended that boiler be fired at the specified firing rate and with an oil burner that complies with Commercial Standard CS-75. Suffix "B" indicates that unit is equipped with an Arcoflame Oil Burner. Suffix "T** indicates that the unit is designed for but not equipped with e built-in tank or tankles type water heater. Nozzle sizes, gal. per hour, furnished wih Arcoliner Oil Heating Units are as follows: No. 153, 0.90-60* or 70* H; No. 154, 1.25-60* or 70* H; No. 155, 1.50-60* or 70* S{ No. 156. 1.65-60* or 70* S. standard equipment oil boiler-burner units Boiler with flush jacket. Arcoflame oil burner Model PH2-6 with hanger mounting for front firing. American-Standard CA-701 stack control. Draft stabilizer. ASME relief valve. Heat Lib-O-Rator high temperature steel combustion chamber. tteam only: No. 11 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard 4S0-8A-1 pressure limit control) and nozzle. wofer only: No. 13 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard CA-65S immersion limit control) and nozzle. oil-fired bo/fers Boiler with flush jacket. Arcoliner oil boilers are regularly furnished less combus tion chambers. See optional equipment and table for size and number. ASME relief valve. optional equipment oil boiler-burner units Jacket extension, providing 2OV2" enclosure in front for concealment of oil burner and controls. Heat Ub-O-Rator molded refractory type combustion chamber may be ordered in place of steel chamber regu larly furnished. See table for size and number (under optional equipment boilers only). The following Arcoflame control sets can be furnished if specified on order: Steam control set No. 12, Water control sets Nos. 23, 15, 16, 26 and 16-Z. Detailed description of Arcoflame control sets is shown on page 46. Model ES 2-6 Arcoflame shell head oil burner; if desired, for use with 3 and 4 section units only, specify on order. Two-stage fuel unit will be furnished if specified on order. Solenoid cut-off valve for use with Arcoflame oil burner. American-Standard 450-BC-l Vapor limit control; if de sired in place of 450-BA-l pressure limit control regularly furnished for steam units. Cover plate for water heater opening will be furnished if specified on order. tttam only: No. 369 McDonnell & Miller Low Water Cut-off available if specified on order. oil-fired boilers Jacket extension, providing 20Va" enclosure in front for concealment of oil burner and controls. Cover plate for water heater opening will be furnished if specified on order. *fm only: No. 369 McDonnell & Miller Low Water Cut-off available if specified on order. Heat Lib-O-Rator molded refractory combustion chambers are available as follows; (toiler number Heat Lib-O-Rator model no. max. firing rate gal. per hour 153-T f 154-T ) 155-T 156-T No. 4 No. 5 No. 6 1.35 1.65 2.00 built-in water heaters Built-in Water Heaters are available for Arcoliner Wet Base Boilers and Oil Heating Units for steam or water in the following sizes; stock no. type capacity-gals. 589 tankless 3 per min 596 tankless per min 587 tank 85 15523 ;ion i oil-fired Arcoli ner wide back type oil boiler-burner units boilers water or steam factory assembled sections^ < wet base "construction flush jacket arranged for, but less, built-in tank or tankless type writer heater dimensions--inlets--outlets 2'l "1 3" SUPPLY 5|x? OPENING dimensions inches boiler number AB DA EA c flush jacket jacket extension S or W-0-153-T* 13 _ 12% 20% S or W-O-154-Tfl 18 -- 17% 25% S or W-O-155-Tfl 23 13 22% 30% S or W-0-156-T 28 13 27% 35% Add lW' to length for smoke collar equipped with crown sheet baffle 407/e 457/a 50% 55% number end sixt tappings inches flow return 1-3 1-3 1-3 1-3 2-3 1-3 2-3 1-3 assemblage of sections boiler number arrangement of sections Steam or water--adapted lor tankless water Heaters no. S(9 or 596 and tank type no. 597 S or W-0-153-T* S or W-O-154-Tfl S s or or W-0-155-T* W-0-156-T WF-WCX-TWB WF-WCX-WC-TWB WF-WCX-WC-WCX-TWB WF-WCX-WC-WC-WCX-TW8 9 With crown sheet baffle. -ode: WF--oil front section; WC-oil center section: WCX-01I center connecting section; TW8--oil back section for flanged type built-in water heater nos. 507. 509 or 596. tappings --control applications location size on boiler inches steam boilers A 2% internal low water cut-off B % pressure control C % water temp, control 0 1% safety valve E IVj blow-off H % not used inserted in smoke pipe stack control vapor boilors internal low water cut-off vapor control water temp, control safety valve blow-off not used stack control water boilors water limit control not used water temp, control relief valve not used reverse acting water temp, control stack control ^American-/Standard ftifjCTgrnnT'.i.T'.r oil-fired Oakmont oil boiler-burner units boilers water or steam B flush jacket--arranged for, but less, built-in tank \ i r't f r-T, >. " or tankless type water heater ratings and data i' m.-jimit'XJ, gp unit or boiler number steam water net l = B = R rating steam BUi/hr sq ft water Btu/hr net installed rating water sq ft grass i=b=r output steam and water burner capacity gph a ehimney ^ size inches height teat oil boiler-bu rner units S-85-OB W-84-OB S-85-08 W-85-OB S-86-0B W-86-OB S-87-08 W-87-OB S-88-08 W-88-08 S-89-08 W-89-08 107,300 447 107,300 715 143,000 1,40 8x8 20 131,300 547 131,300 875 175,000 1.75 8x8 25 151,500 631 151,500 1010 202,000 2.00 8x8 25 172,500 719 172,500 1150 230,000 2.30 8 x 12 30 195,800 816 195,800 1305 261,000 2.55 8 x 12 30 216,100 900 216,100 1440 288,000 2.80 8 x 12 35 oil-fired boil)irs S-84 eS-85 S-86 S-87 S-88 S-89 W-84 W-85 W-86 W-87 W-88 W-89 107,300 131,300 151,500 172,500 195,800 216,100 447 547 631 719 816 900 107,300 131,300 151,500 172,500 195,800 216,100 715 875 1010 1150 1305 1440 143,000 175,000 202,000 230,000 261,000 288,000 1.40 1.75 2.00 2.30 2.55 2.80 8x8 8x8 8x8 8 x 12 8 x 12 8 x 12 20 25 25 30 30 35 The ratines of these boilers represent the maximum net loads that may be connected to the boilers. Allowances have been made for normal piping and pick-up loads. Equipped with Crown Sheet Baffle. Nozzle sizes, gph, 60* or 70* S, furnished with Oakmont units are: model numbers 84, 1.35; 85, 1.65; 86, 2.00; 87, 2.25; 88, 2.50 and 89, 2.75. standard equipment oil boiler-burner units Boiler with flush jacket. Arcoflame oil burner Model PH2-6 with hanger mounting for rear firing. American-Standard CA-701 stack control. Draft stabilizer. ASME relief valve. Heat Lib-O-Rator refractory combustion chamber. See table for Model Number. steam only: No. 11 Arcoflame control set (American-Standard CA-412 thremostat, American-Standard 450-BA-l pressure limit control! and nozzle. water only: No. 13 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard CA-655 immersion limit control) and nozzle. oil-fired boilers Boiler with flush jacket. ASME relief valve. optional equipment oil boiler-burner units Jacket extension, if specified on order. It provides a 15%" enclosure at rear for concealment of oil burner and controls. The following Arcoflame control sets can be furnished if specified on order: Steam control set No. 12, Water control sets Nos. 23, 15, 16. 26 and 16-Z. Detailed description of Arcoflame control sets is shown on page 46. Model ES-2-6 Arcoflame shell head oil burner: if desired, for use with Unit No. S or W-84-OB only, specify on order. Two-stage fuel unit will be furnished if specified on order. Solenoid cut-off valve for use with Arcoflame oil burners. American-Standard 450-8C-1 vapor limit control; if desired in place of 450-BA-l pressure limit control regularly furn ished for steam units. Cover plate for water heater opening will be furnished if specified on order. oil-fired boilers Jacket extension; if desired specify on order. It provides 15%" enclosure in rear for concealment of oil burner and controls. Cover plate for water heater opening will be furnished if specified on order. Molded refractory combustion chambers. built-in water heaters Built-in Water Heaters are available for Oakmont Boilers and Boiler-Burner Units, see page 5. heat Lib-O-Rator molded refractory combustion chambers Oakmont oil heating unit Heat l.ib*0*Rator no. 84 00 85 1 86 2 87 3 88 3 89 3 For Dimensions, see Page 49 maximum firing rate, gph 1.50 1.75 2.25 3.00 3.00 3.00 15525 T 't* oil-fired 27 Oakmont oil boiler-burner units boilers water or steam flu.*- rlwa^ wtif-v r* .k br^KIST^wfeTheoter 3"tappings 3' TAPPINGS aid* view extended jacket beck view extended jeeket cutaway thru boiler section* extended jacket dimensions--inlets--outlets boiler number steem water S-84 S-85 S-86 S-87 S-88 S-89 W-84 W-85 W-86 W-87 W-88 W-89 AB c EF L 14 ___ 11 15 26% 40% 25 14 -- 14Va I8V1 30% 44V* 28% 14 7 11 22 26% 47% 32 14 7 14Vi 25Vi 30Va 51V* 35Vs 14 14 11 29 26% 54% 39 14 14 14Vi 32Vs 30V 58V* 42% side view Hush jeeket OPENING 2*XI5* cutaway thru boiler sections flush jacket assemblage of sections boiler or unit number steam water arrangement of sections S-84 S-85 S-86 S-87 S-88 S-89 W-84 W-85 W-86 W-87 W-88 W-89 F-CX-B F-CX-NC-8 F-CX-CX-B F-CX-CX-NC-B F-CX-C-CX-B F-CX-C-CX-NC-B Code: F -- T front section C -- 7" center section CX -- 7" center connecting section NC -- 3Vi " narrow center section B -- 6V2" back section tappings--control applications location sizeon boiler inches steam boilars vapor boilars water boilars A&B 1 external low external low "A" alternate water control water control water limit control or feeder or feeder "B" reverse acting water temp, control C 2% internal low internal low water limit control water cut-off water cut-off 0% operating temperature control for tankless water heaters E1 operating temperature control for tank type water heaters F 1V2 blow-off blow-off alternate water limit control G V2 pressure vapor-control control not used H IV* safety valve safety valve relief valve inserted in smoke pipe -- stack control stack control stack control /)American-Standard 15526 BOI oil-fired flush jacket oil boiler-burner units water or steam ratings and data unit number steam water net l = B=R rating steam Btu/hr sq ft water Btu/hr net rating water sq ft gross 1=B=R output stsam and water oil boiler-bu rner unit A-504-SB A-504-WB A-505-SB A-505-WB A-506-SB A-506-WB A-507-SB A-507-W8 A-508-SB A-508-W8 A-509-SB A-509-WB 195,800 259,600 319,600 381,100 441,100 501,100 816 1082 1332 1588 1838 2088 195,800 259,600 319,600 381,100 441,100 501,100 1305 1731 2131 2541 2941 3341 261,000 346,000 426,000 508,000 588,000 668,000 oil-fired boil ers A-504-S A-504-W A-505-S A-505-W A-506-S A-506-W A-507-S A-507-W A-508-S A-508-W A-509-S A-509-W A-510-S A-510-W A-511-S A-511-W 195,800 259,600 319,600 381,100 441,100 501,100 561,100 622,700 816 1082 1332 1588 1838 2088 2338 2594 195,800 259,600 319,600 381,100 441,100 501,100 561,100 622,700 1305 1731 2131 2541 2941 3341 3741 4151 261,000 346,000 426,000 508,000 588,000 668,000 748,000 830,000 Nozzle size, gph, furnished with A-5 units are as follows; No. A-504, 2.50--60* or 70* S; A-505, 3.00-80* H; A-506. 3.50-80* H; A-507. 4.50-80' H; A-508. 5.00-60" H; A-509. 6.00-60* H. l=B=R burner capacity gal per houra chimney size inches height feet 2.55 3.30 4.00 4.75 5.55 6.30 8x 12 8x 12 12 x 12 12 x 12 12 x 16 12 x 16 15 20 20 20 25 25 2.55 3.30 4.00 4.75 5.55 6.30 7.00 7.65 8x 12 8x 12 12 x 12 12 x 12 12 x 16 12 x 16 12 x 16 16 x 16 15 20 20 20 25 25 25 30 standard equipment oil boiler-burner units Boiler with flush jacket. Model PH2-5 Arcoflame oil burner for A-504. Model LF-A Arcoflame oil burner with two-stage fuel unit for A-505 through A-509. Both burners arranged for front firing. American-Standard CA-701 stack control. Draft stabilizer. ASME relief valve. Heat Lib-O-Rator refractory combustion chamber; see table. steam only: No. 11 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard 450-BA-l pressure limit control) and nozzle. wafer only: No. 13 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard CA-655 immersion limit control) and nozzle. oil-fired boilers Boiler with flush jacket. ASME relief valve. optional equipment oil boiler-burner units & boilers only Jacket extension; if desired specify on order. It provides 25" enclosure in front for concealment of oil burner and controls. oil boiler-burner units The following Arcoflame control sets can be furnished if specified on order-. Steam control set No. 12, Water control sets Nos. 23, 15, 16, 26, 16-Z, 36 and 36-Z. Detailed description of Arcoflame control sets is shown on page 46. American-Standard 450-BC-l vapor limit control; if desired in place of 450-BA-l pressure limit control regularly fur nished for steam units. Two-stage fuel unit for PH2-5 Arcoflame oil burner will be furnished if specified on order. Solenoid cut-off valve for use with PH2-5 Arcoflame oil burner. oil-fired boilers Heat Lib-O-Rator refractory combustion chamber; see table. 15527 r BOILERS oil-fired oil boiler-burner units boilers water or steam i -Vi-?- flush jacket tankless heaters No. S30 tankless heaters available for single purpose or multiple parallel hook-up. Copper manifolds (illustrated on page 30) for two, three or four-heater parallel arrangement furnished with 530 heater if specified. If desired, provision for tankless heater is available. If suf fix letter "T" is added on order to above unit or boiler numbers, the following sr of openings in center sec- tions will be furnished: Boiler or Unit No. A-504-T 2 Openings Boiler or Unit No. A-505-T 3 Openings Boiler or Unit No. A-506-T 3 Openings Boiler or Unit No. A-507-T 3 Openings Boiler or Unit No. A-508-T 3 Openings Boiler or Unit No. A-509-T 4 Openings Boiler No. A-510-T 4 Openings Boiler No. A-511-T 4 Openings Note: Additional openings can be specified on order. no. 530 tankless heater ratings Domestic Hot Water Supply; recommended number of heaters to be used with each boiler if connected in parallel: boiler no. no. of heaters rating-gpm All Sizes All Sizes A-505--A-511 A-508--A-511 A-510--A-511 i 2 3 4 5 4 7 13 13 16 Nott: Additional heaters can be added if the heaters are serving different systems and it is not likely that heaters will all be in use at the same time. Cover plate for water heater openings will be furnished if specified on order for "T" type units and boilers. sfeom only: No. 369 McDonnell & Miller Low Water Cut-off. e assemblage of sections boiler number* arrangement of sections from front of boiler for boilers with water heater steam water t 2 2 4- 5 6 7 a 9 10 11 A-504-S A-504-W FX CT CT BX A-505-S A-505-W FX CT CT CT BX A-506-S A-506-W FX CT CT CT C BX A-507-S A-507-W FX CT CT CT C C BX A-508-S A-508-W FX CT CT CT c c c BX A-509-S A-509-W FX CT CT CT CT c C C BX A-510-S A-510-W FX CT CT CT CT c c c C BX A-511-S A-511-W FX CT CT CT CT c c C C C BX boiler numbers steam water arrangement of sections from front of boiler for boilers without water heater 1 2 2 4 5 6 7 a 9 IQ 11 A-504-S A-504-W FX C c BX A-505-S A-505-W FX c c c BX A-506-S A-506-W FX c c c c BX A-507-S A-507-W FX c c c c c BX A-508-S A-508-W FX c c c c c c BX A-509-S A-509-W FX c c c c c c c BX A-510-S A-510-W FX c c c c c c c c BX A-511-S A-511-W FX c c c c c c c c c BX Code: FX-Front connecting CX-Center with water heater opening C-Center without water heater opening BX--Back connecting heat lib-O-Rator molded refractory combustion chambers unit or boiler number Heat Lib*0Rator max firing rate model no. included gal per hour A-504 14 A-505 15 A-506, 507, 508 16 A-509 17 A-510, 511 17 Listed for inclusion with A-510 and A-5I1 Boilers only. 2.55 3.30 5.55 7.65 7.65 tappings -- control applications location size of tappings steam F 2Vz low water cut-off G % pressure limit control H % operating cont. tankless heater J Vi pressure gage K% not used L V. not used Note: 2* blow-off on back of back section. T safety or relief valve on top of back section. water not used temperature limit control not used comb, altitude gage and thermometer operating control tankless heater reverse acting control 15528 minimum piping recommendations for A-5 boilers (number and sis# of outlets) boiler size steam no. size water no. size A-504 i 3" i 1V2" A-505 i 4"' i 2" A-506 i 4" i 2" A-507 i 4" i 2V2" A-508 i 4" i 2Vi" A-509 2 3" i 2Vi" A-510 2 4" i 3" A-511 2 4" i 3" Nate: On gravity circulation use both outlets of sizes shown above. ^American-Standard oil-fired A-5 oil boiler-burner units boilers water or steam flush jacket boiler number number of sections number and site tappings Now return A-504 4 2-4" A-S05 5 2-4" A-506 6 2-4" A-507 7 2-4" A-508 a 2-4" A-509 9 2-4" A-510 10 2-4" A-511 11 2-4" for boiler-burner units only tankless heater piping 4-2% " 4-2% " 4-2% " 4-2% " 4-2% " 4-2% " 4-2% " 4-2% " A 18 22to 27 31% 36 40Vi 45 49% dimensions - inehss B c 0 13V* 9 11% 16% 9 11% 16% 10 12 16% 10 12 16% 10 12 16V* 12 13 16% 12 13 16% 12 13 c 9% 9% 10 10 10 11 11 11 F 15% 20 24% 29 33% 38 42% 47 6 flush jacket 22% 27% 31% 36% 40% 45% 49% 54% H jacket extension 47% 52% 56% 61% 65% 70% 74% 79% Note: Single arrangement or any combination of the above manifold piping arrangements can be used. It is important that water heaters be assembled in boiler starting with the second section from front of boiler. Heaters are installed with the word "water" to top on water boilers and "steam" to top on steam boilers. 15529 oil or stoker Exbrook oil boiler-burner units. oil-fired or stoker-fired boilers water or steam *i: /flush jacket - ratings and data number net 1 = B = R rating steam Btu/hr sq. ft water Btu/hr net installed rating water sq. ft gross 1=B=R output steam water l=B=R burner capacity gphe Ib./hr ehimney size inches height feet oil boiler-burner units S- 207-OB as- 208-OB S- 209-08 S-2010-OB S-2011-OB S-2012-OB aW- 207-OB aW- 208-OB W- 209-OB W-2010-OB W-2011-OB W-2012-OB 207,100 251,300 297,100 339,100 381,100 423,100 863 1047 1238 1413 1588 1763 207,100 251,300 297,100 339,100 381,100 423,100 1380 1675 1980 2261 2541 2821 276,000 335,000 396,000 452,000 508,000 564,000 2.75 3.30 3.90 4.45 5.00 5.50 _ _ _ _ _ _ 8x 12 8x 12 12 x 12 12 x 12 12x12 12 x 16 25 25 30 30 35 40 S-2013-OB W-2013-OB 465,100 1938 465,100 3101 620,000 5.95 -- 12 x 16 40 oil-fired boilers as- 207 aW- 207 as- 208 aw- 208 S- 209 W- 209 S-2010 S-2011 W-2010 W-2011 S-2012 W-2012 S-2013 W-2013 207,100 251,300 297,100 339,100 381,100 423,100 465,100 863 1047 1238 1413 1588 1763 1938 207,100 251,300 297,100 339,100 381,100 423,100 465,100 1380 1675 1980 2261 2541 2821 3101 276,000 335,000 396,000 452,000 508,000 564,000 620,000 2.75 3.30 3.90 4.45 5.00 5.50 5.95 _ _ _ 8x 12 8x 12 12 x 12 -- 12 x 12 _ 12 x 12 -- 12 x 16 -- 12 x 16 25 25 30 30 35 40 40 stoker-fired boilers SC- 207 SC- 208 SC- 209 SC-2010 SC-2011 SC-2012 SC-2013 WC- 207 WC- 208 WC- 209 WC-2010 WC-2011 WC-2012 WC-2013 207,100 251,300 297,100 339,100 381,100 423,100 465,100 863 1047 1238 1413 1588 1763 1938 207,100 251,300 297,100 339,100 381,100 423,100 465,100 1380 1675 1980 2261 2541 2821 3101 276,000 335,000 396,000 452,000 508,000 564,000 620,000 -- -- -- -- -- -- -- 30 8x 12 37 8x 12 43 12 x 12 50 12 x 12 56 12 X 12 62 12 x 16 68 12x16 25 25 30 30 35 40 40 NOTE: Nozzle Sizes, gal per hour, furnished with Exbrook Units are as follows: 80* H, No. 207, 3.0; No. 208, 3.5; No. 209, 4.0; No. 2010, 4.5; 60* H, No. 2011, 5.0; No. 2012, S.S; No. 2013, 6.0. Equipped with Crown Sheet Baffle. standard equipment oil boiler-burner units Boiler with flush jacket. Model LF-E Arcoflame oil burner with two-stage fuel unit, arranged with flange mounting for front firing. American-Standard CA-701 stack control. Draft stabilizer. ASME relief valve. Heat Ub-O-Rator refractory combustion chamber, steam only: No. 11 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard 450-BA-l pressure limit control) and nozzle. woter only: No. 13 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard CA-655 immersion limit control) and nozzle. oil-fired boilers Boiler with flush jacket. ASME relief valve. stoker-fired boilers Boiler with flush jacket. ASME relief valve. built-in water heaters Boilers listed here are not adapted for Built-in Water Heater. If Oil Boilers or Units are desired for use with Tank or Tankless Type Water Heaters, or if Stoker Boilers adapted for Tank Type Heaters are wanted, add suffix "T" to numbers shown. For example S-209-T, S-209-OB-T, or SC-209-T. For sizes of Built-in Water Heaters for the Exbrook, see page S. ----------------------------------------------- optional equipment 15530 oil boiler-burner units The following Arcoflame control sets can be furnished if specified on order: Steam control set No. 12, Water control sets No. 23, 15, 16, 26, and 16-Z. Detailed description of Arcoflame control sets is shown on page 46. American-Standard 450-BC-l vapor limit control, if desired in place of 450-BA-l pressure limit control regularly fur nished for steam units. Cover plate for water heater opening, if specified on order for "T" type units. oil-fired boilers Built-in water heaters are available for use with Exbrook "T" type boilers only. Molded refractory combustion chamber for Exbrook boiler. Cover plate for water heater opening will be furnished if specified on order for "T" type boilers. stoker-fired boilers Built-in water heaters are available for use with Exbrook "T" type boilers only. Cover plate for water heater opening will be furnished if specified on order for "T" type boilers. .^AMERiCAiv-^tandard 32 oil or stoker flush jacket dimensions--inlets--outlets center section--showing tankless water heater COTsection reversible water heater either side cutaway thru boiler sections back view showing control tappings -v: boiler number number and site tappings mehos t dimensions--inches 3 steam water flow return A B c D H Le ^ S-207 S-208 S-209 S-2010 S-2011 S-2012 W-207 W-208 W-209 W-2010 W-2011 W-2012 2-4 2-4 2-4 2-4 3-4 3-4 2-4 2-4 2-4 2-4 2-4 2-4 10 15 10 15 10 15 20 20 30 30 40 40 _ _ _ __ 30 30 _ _ _ _ _ _ 29% 34% 39% 44% 49% 54% 35y, 40% ^ 45% i] 50% | 55% 1 60V. 3 S-2013 W-2013 3-4 2-4 10 50 20 20 59% 65% A Add 2to length for Smoke Collar. NOTE: Same data applies to "T" Type Exbrook Boilers, such as S2ot, etc. boiler number assemblage of sections without built-in water heater with built*in water healer sfi */ i 207 208 209 2010 2011 2012 2013 AO-FCXO-CO-BX FO-CXO-CO-BX AO-FCXO-CO-CO-BX FO-CXO-CO-CO-8X AO-FCXO-CO-CO-RCXO-BX FO-CXO-CO-CO-RCXO-BX AO-FCXO-CO-CXO-CO- RCXO-BX* AO-FCXO-COT BX f FO-CXO-COT-BX 1 AO-FCXO-CO-COT-BX FO-CXO-CO-COT-BX AO-FCXO-COT-CO-RCXO-BX S FO-CXO-COT-CO-RCXO-BX P A&pCXO-COT-CXO-CO- t; RCXO-BX* ^ CODE; AO--5* Front Section; FO-IO" Front Section; CO-Center Section; COT-- Center Section with opening for Built-in Water Heater; CXO-Center Connecting Section; FCXO-Front Center Connecting Section; RCXO-Rear Center Connect* ing Section; BX-Back Connecting Section. *4" flow tapping plugged on back section. location on boilor tappings--control applications sica inches steam boilar water bailer A at i external feeder external feeder reverse acting front water tempera section ture control B 2% internal low internal low water limit control water control water control C 2 pressure control vapor control not used 0 2 safety valve safety valve for relief valve E 2% external water external water external water heater heater heater F % water tempera water tempera water tempera ture control ture control ture control G 1% blow-off blow-off alternate water limit control H % water temperature control for tankless water heaters See front view illustration, e See center section illustration. heat Lib-O-Rator molded refractory combustion chambers Exbrook oil heating unit 207, 208 & 209 2010, 2011, 2012 & 2013 For dimensions, see page 49. heat*Lib*0-Rator model no.a 7 8 maximum firing rate--gph 4.50 6.50 15531 oil, stoker or hand-fired oil boiler-burner units, Severn oil, stoker & hand-fired boilers water or steam ratings and data boiler number steam watar installed radiation steam water sq ft Btu/hr sq ft gross output Btu/hr firing rate chimney gal* or lbs per size height hour inches feet oil boiler-burner units - arranged for but less built-in tank type water heeter. S-17-08 eW-17-OB 456 109,500 730 146,000 1.5 8x8 20 S-21-0B eW-21-OB 525 126,000 840 168,000 1.7 8x8 25 S-25-OB eW-25-OB 588 141,000 940 188,000 1.9 8x8 25 S-29-OB W-29-OB 675 162,000 1080 216,000 2.2 8x12 25 S-33-OB W-33-OB 772 185.300 1235 247,000 2.5 8x12 30 S-37-OB W-37-OB 869 208.600 1390 278,000 2.8 8x12 30 I -arranged for but less built-in tank or tankless type water heater. S-17-0B-T eW-17-OB-T 456 109,500 730 146,000 1.5 8x8 20 eS-21-OB-T eW-21-OB-T 525 126,000 840 168,000 1.7 8x8 25 S-25-OB-T W-25-OB-T 588 141,000 940 188,000 1.9 8x8 25 S-29-OB-T W-29-OB-T 675 162.000 1080 216,000 2.2 8x12 25 S-33-OB-T W-33-OB-T 772 185,300 1235 247,000 2.5 8x12 30 S-37-OB-T W-37-OB-T 869 208,600 1390 278,000 2.8 8x12 30 Equipped with Crown Sheet Baffle. e NOTE: Nozzle sizes, sal per hr, furnished with Severn units are: Model No. 17, 1.50? No. 21, 1.75; No. 25, 2.00? No. 29, 2.25; No. 33, 2.50; No. 37, 2.75. oil-fired boilers -arranged for but less built-in tank typa watar heater. S-17-0 W-17-0 456 109.500 730 146,000 1.5 8x8 eS-21-0 eW-21-0 525 126,000 840 168,000 1.7 8x8 BS-25-0 eW-25-0 .588 141,000 940 188,000 1.9 8x8 S-29-0 W-29-0 675 162,000 1080 216,000 2.2 8x12 S-33-0 W-33-0 772 185,300 1235 247,000 2.5 8x12 S-37-O W-37-0 869 208.600 1390 278.000 2.8 8x12 -arranged for but less built-in tank or tankless type weter heeter. S-17-0-T eW-17-O-T 456 109,500 730 146,000 1.5 8x8 S-21-0-T 1W-21-0-T 525 126,000 840 168,000 1.7 8x8 S-25-0-T iW-25-O-T 588 141,000 940 188.000 1.9 8x8 S-29-0-T W-29-O-T 675 162,000 1080 216,000 2.2 8x12 S-33-0-T W-33-0-T 772 185,300 1235 247,000 2.5 8x12 S-37-0-T W-37-0-T 869 208,600 1390 278,000 2.8 8x12 Eauipped with Crown Sheet Baffle. 20 25 25 30 30 30 20 25 25 25 30 30 stoker-fired boilers -arranged for but lass built-in tank typa watar heater. SC-17 WC-17 456 109,500 730 146,000 1.6 8x8 SC-21 WC-21 525 126,000 840 168,000 1.8 8x8 SC-25 WC-25 588 141,000 940 188,000 2.1 8x8 SC-29 WC-29 675 162,000 1080 216,000 2.4 8x12 SC-33 WC-33 772 185,300 1235 247,000 2.7 8x12 SC-37 WC-37 869 208.600 1390 278.000 3.1 8x12 -- arranged for but less built-in tank or tankless type water heeter. SC-17-T WC-17-T 456 109,500 730 146,000 1.6 8x8 SC-21-T WC-21-T 525 126,000 840 168,000 1.8 8x8 SC-25-T WC-25-T 588 141,000 9A0 188,000 2.1 8x8 SC-29-T WC-29-T 675 162,000 1080 216,000 2.4 8x12 SC-33-T WC-33-T 772 185,300 1235 247,000 2.7 8x12 SC-37-T WC-37-T 869 208.600 1390 278,000 3.1 8x12 20 25 25 25 30 30 20 25 25 30 30 30 hand-fired boilers -arranged for but less built-in tank typa water heater. S-17 W-17 353 84,700 565 194,000 S-21 W-21 453 108,700 725 244,000 S-25 W-25 553 132,700 885 296,000 S-29 W-29 630 151,300 1009 328,000 S-33 W-33 710 170,500 1137 364,000 S-37 W-37 783 187,900 1253 396,000 -- 3x8 30 -- 8x8 30 -- 8x12 35 -- 8x12 35 -- 8x12 40 -- 12x12 43 built-in water heaters For type and number of built-in water heaters for the Severn see page 5. beat Lib-O-Rator combustion chambers Severn oilheating unit Heat Lib-O-Rator mode) number 17, 21 25, 29 33, 37 For Dimensions-See Page 47, i 2 3 maximum firing rate, gph 1.75 2.25 3.00 gjpuih jacket rK-A . standard equipment oil boiler-burner units Boiler with flush jacket. Arcoflame oil burner Model PH2-6 with hanger mounting for front firing. American-Standard CA-701 stack control. Oraft stabilizer. ASME Relief valve. Heat Lib-O-Rator refractory combustion chamber; see table. sfeoin only: No. 11 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard 450-BA-l pressure limit control) and nozzle. watmr only: No. 13 Arcoflame control set (American-Standard CA-412 thermostat, American-Standard CA-655 immersion limit control) and nozzle. oil-fired boilers Boiler with flush jacket. ASME relief valve. stoker-fired boilers Boiler with flush jacket. ASME relief valve. hand-fired boilers Boiler with flush jacket. ASME relief valve. 15532 optional equipment oil boiler-burner units The following Arcoflame control sets can be furnished if specified on order; Steam control set No. 12, Water control sets No. 23, 15, 16, 26, and 16-Z. Detailed description of Arcoflame control sets is shown on page 46. Model ES 2-6 Arcoflame shell head oil burner: If desired for use with A or W-17-OB and S or W-17-OB-T units only, specify on order. Two-stage fuel unitwill be furnished if specified on order. Solenoid cut-off valve for use with Arcoflame oil burners. American-Standard 450-BC-l vapor limit control: If de sired in place of 450-BA-l pressure limit control regu larly furnished for steam units. Cover plate for water heater opening will be furnished if specified on order for "T" type units. oil-fired boilers Cover plate for water heater opening will be furnished if specified on order for "T" type boilers. Molded refractory combustion chamber. stoker-fired boilers Cover plate for water heater opening will be furnished if specified on order for "T" type boilers. hand-fired boilers Note: Built-in water heaters are not recommended for hand-fired water boilers. .^American-^Standard t  34 oil, stoker or hand-tired oil boiler-burner units, Severn oil, stoker & hand-fired boi lers water or steam ' front view hand firod 'OPENING-8`x ll` back viaw ail find side viaw hand fired cutaway thru boiler sections oil fired boiler number number and size of tappings--inches dimensions--inches steam water flow return A B cD S-17 S-21 S-2S S-29 S-33 S-37 W-17 W-21 W-25 W-29 W-33 W-37 1-3 2-3 1-4 1-3 2-3 1-4 1-3 2-3 1-4 1-3 2-3 1-4 1-3 2-3 1-4 1-3 2-3 2-4 n% 15% 11% 15% 19% 15% 7% 7V* 15% 15% 15% 23% _ 17 -- 21 -- 25 -- 29 -- 33 16 37 NOTE: Same data applies to all Severn boilers--hand-fired oil, stoker, and *`T" type. On hand>ftred boilers, add 12Va" to length for smoke hood. On oil and stoker-fired, add 2" for smoke collar. E 4% 6% 8% 10% 12% 14% Lfl 23% 27% 31% 35% 391% 43% 15533  oil, stoker or hand-fired oil boiler-burner units, Severn oil, stoker & hand-fired boilers water or steam assemblage of sections Air-uWjr X boilor number it.am water arrangamant of sections number of grato ban uaad S-17 S-21 S-25 S-29 S-33 S-37 W-17 W-21 W-25 W-29 W-33 W-37 F-CX-BO F-NC-CX-BO F-CX-C-BO F-NC-CX-C-BO F-C-CX-C-BO F-NC-CX-C-CX-BO 4 5 Code: F --7% - front section 6 C --8- center section CX --8" center connecting section 7 NC --4- center section 8 BO --6% " back section 9 NOTE: On "T" type boilers, for use with built-in tank type water heaters Nos. 594 and 595 and built-in tankless heater No. 590, a "CXT' 6" center connecting section, interchangeable with regular "CX,r section, is furnished on special order. tappings--control applications i|*RD.HD. BOLT BACK SECTION cutaway thru oil boiler showing baffle in position location on boiler A&B C 0 E F H smoke pipe size of tapping inches i 2Vz IVj 1 IV. 2Va -- steam boilers external low water control or feeder internal low water control pressure control water temperature control safety valve built-in water heater stack control vapor boilors external low water control or feeder internal low water control vapor control water temperature control safety valve built-in water heater stack control watar boilors "A" alternative water limit control. "B" not used water limit control not used water temperature control for relief valve built-in water heater stack control 15534 tvAMERiCAN-TrtandaH oil, stoker or hand-fired oil-fired, stoker-fired A-7 hand-fired boilers water or steam jacketed or unjacketed - ,'T.^v.r-6 ratings and data boiler number steam | water net 1 -- 8 -- R ratings steam Btu/hr | *q- ft- water Btu/hr net installed ratings water sq. ft gross i=b=r output l=B=R burner capacity gph tbs/hr chimney size inches height feet oil-fired A-705-SO A-705-WO 649,700 2707 649,700 4331 866,000 8.15 _ 16 x 16 28 A-706-SO A-706-WO 769,200 3163 759,200 5061 1,012,000 9.55 -- 16 x 16 30 A-707-SO A-707-WO 897,200 3738 897,200 5981 1,196,000 11.25 -- 16x20 36 A-708-SO A-708-WO 1,041,600 4340 1,041,600 6944 1,376,000 12.90 -- 16x20 42 A-709-SO A-709-WO 1,203,100 5013 1,203,100 8020 1,570,000 14.65 -- 16x20 45 A-710-SO A-710-WO 1,361,200 5672 1,361,200 9075 1,760,000 16.30 -- 20x20 50 A-711-SO A-711-WO 1,518,600 6328 1,518,600 10125 1,956,000 18.00 -- 20x20 55 A-712-SO A-712-WO 1,667,700 6949 1,667,700 11118 2,148,000 19.65 -- 20x20 60 Crown sheet refractory baffle furnished on 5 section oil-fired boilers only Flue baffles furnished 5 section thru 8 section oil-fired boilers. stoker-fired A-705-SC A-706-SC A-707-SC A-708-SC A-709-SC A-710-SC A-711-SC A-712-SC A-705-WC A-706-WC A-707-WC A-708-WC A-709-WC A-710-WC A-711-WC A-712-WC 649,700 759,200 897,200 1,041,600 1,203,100 1,361,200 1,518,600 1,667,700 2707 3163 3738 4340 5013 5672 6328 6949 649,700 759,200 897,200 1,041,600 1,203,100 1,361,200 1,518,600 1,667,700 4331 5061 5981 6944 8020 9075 10125 11118 866,000 1,012,000 1,196,000 1,376,000 1,570,000 1,760,000 1,956,000 2,148,000 -- 95 -- 111 -- 131 -- 151 -- 172 -- 194 -- 215 236 16 x 16 16 x 16 16x20 16 x 20 16x20 20 x 20 20x20 20x20 28 30 36 42 45 50 55 60 hand-fired [coal) A-705-S A-705-W 625,400 2606 625,400 4169 1,122,000 -- A-706-S A-706-W 744,300 3101 744,300 4962 1,298,000 -- A-707-S A-707-W 894,000 3725 894,000 5960 1,510,000 -- A-708-S A-708-W 1,042,100 4342 1,042,100 6947 1,708,000 -- A-709-S A-709-W 1,202,000 5008 1,202,000 8013 1,910,000 -- A-710-S A-710-W 1,363,500 5681 1,363,500 9090 2,108,000 -- A-711-S A-711-W 1,518,200 6326 1,518,200 10122 2,288,000 -- A-712-S A-712-W 1,667,300 6947 1,667,300 11115 2,456,000 -- Note: All sizes and models of the A-7 boiler have tappings for external-type domestic water heaters on rear section. -- -- -- -- -- -- -- -- 16 x 16 16x20 20x20 20x20 20x20 20x24 20 x 24 24x24 40 45 50 55 60 65 70 75 standard equipment oil, stoker and hand-fired boilers ASME relief valve. (Also see page 5.) A-7 minimum piping requirements for automatic firing boiler no. A-705 A-706 A-707 A-708 A-709 A-710 A-711 A-712 steam water boiler risers 2-4" 2-4" 2-4" 3-4" 3-4" 3-4" 4-4" 4-4" supply equalizer header size 5" 2" 5" 2" 5" 2W 5" 2Va" 6" 3" 6" 3" 6" 4" 6" 4" boiler risers 1-3" 1-4" 1-4" 1-4" 1-4" 2-3" 2-4" 2-4" return header 3" 4" 4" 4" 4" 4" 4" 4" optional equipment oil and stoker-fired boilers Steel pedestal bases for installation under the regularly furnished 12" base for greater base heights will be fur nished if specified on order. Bases available: 5 through 7 section boilers -- 8" high 8 through 12 '' " -- 10" high If aforementioned steel pedestal bases are not used, a 20" base height for the 5 through 7 section and a 22" base height for the 8 through 12 section boilers must be pro vided in some other manner. Recommended firing rate for Oil and Stoker boilers re quires additional base height. If insufficient headroom is available, pitting may be necessary to provide sufficient space for combustion chamber. Complete recommendations may be obtained in installation instructions. FOR COMBUSTION CHAMBER DIMENSIONS, SEE PAGE 50. Also see page 4 (boilers . . . stoker-fired) steam only: No. 369 McDonnell & Miller Low Water Cut-off. 15535 ] dimensions--inlets--outlets oil, stoker or hand-fired A-7 oil-fired, stoker-fired hand-fired boilers water or steam jacketed or unjacketed a pipe taps boiler number of number sections A 705 A 706 A 707 A 708 A 709 A 710 A 711 A 712 5 6 7 8 9 10 11 12 dimensions CL 34% 42% 49% 57% 64% 72% 79% 87% 41V2 49 56% 64 71% 79 86% 94 A-4' flow tapping E F number of 4" flow tappings 2 3 3 3 4 4 4 5 number of$* return tappings 2 2 2 2 2 2 2 2 assemblage of sections boiler number arrangement of sections A 705 A 706 A 707 A 708 A 709 A 710 A 711 A 712 FX, C, C, C, BX FX, C, CX, C, RC, BX FX, C, C, CX, C, RC, BX FX, FC, C, CX, C, RC, RC, BX FX, FC, CX, C, C, CX, RC, RC, BX FX, FC, CX, C, C, CX, C, RC, RC, BX FX, FC, FC, CX, C, C, CX, RC, RC, RC, BX FX, FC, FC, CX, C, C, CX, C, RC, RCX, RC, BX Code: FX --front connecting section C --center section CX --center connecting section FC --front center section RC --rear center section RCX--rear center connecting section BX --back connecting section tappings --control applications location size on boiler inches steam water 15536 back view showing control tappings G B M 3s drain tapping A4 water heater--external type B 6 water heater--external type water heater--external type C 1 damper regulator--hand-firing 0 2% pop safety valve relief valve E 3 blow-off or pop safety valve water heater--external type F 3 water heater--external type water heater--external type G 3 water heater--external type water heater--external type H Vs steam pressure limit control water temperature limit control K 2% low water cut-off L Vs water temperature control, water temperature control, domestic hot water domestic hot water M 1V2 nipple port inspection tapping nipple port inspection tapping LvAMERiCAN-^tandard Ul or hand-fired No. 3 Redflash water or steam jacketed and unjacketed ratings and data boiler number steam water stoker-fired 3-SC-8 3-WC-8 3-SC-9 3-WC-9 hand-fired (coal) 3-S-6 3-S-7 3-W-6 3-W-7 3-S-8 3-S-9 3-W-8 3-W-9 steam sqft installed radiation water 4 ttnn Btu/hr water sq ft 2207 2494 529,600 598,600 3531 3991 1503 1799 2100 2400 360,600 431,800 504,100 576,000 2404 2879 3360 3840 standard equipment stoker and hand-fired boilers ASME relief valve. (Also see page 5) hand-fired boilers Buckwheat coal grate bars will be furnished if specified on order. groti output Btu/hr firing rata lb par hour 706,000 798,000 696,000 814,000 932,000 1,046,000 78 88 __ -- -- -- siaa inches 12 x 16 16 x 16 12 x 16 16 x 16 16 x 16 16 x 16 height feet 30 30 40 45 45 50 dimensions--inlets--outlets front viow back view stoker fired cutaway thru boiler sections stoker fired boiler number outlets inlets number and number and dimension-inches siae- steam water inches inches B c D E f G H La 3-S-6 3-W-6 2-4 2-5 18 __ _ _ _ 9 29% 36 3-S-7 3-W-7 3-4 2-5 12 12 -- -- -- 9 35% 42 3-S-8 3-W-8 3-4 2-5 18 12 -- ___ -- 9 41% 48 3-S-9 3-W-9 4-4 2-5 12 12 12 -- -- 9 47% 54 On hand-fired, add 21" to length for smoke hood. On stoker-fired, add 3W" for smoke collar. 15537