Document O3KpeEwp1gXmybZMqajd55aZp

Engineering Material Specification Material Name ASBESTOS PAPER BASE - PHENOLIC LAMINATE Specification Number f ESF-M3D80-A 1. SCOPE The material defined by this specification is an asbestos paper base, laminated sheet material thoroughly impregnated with a thermosetting resin. 2. APPLICATION This specificatiog was released originally for material used where continuous high temperature (204C) and mechanical strength are required such as the armature thrust washer in the starting motor. 3. REQUIREMENTS 3.1 TENSILE STRENGTH, min (ASTM D 638) WMD AMD 3.2 FLEXURAL STRENGTH, min (ASTM D 790) 9500 psi (66 MPa) 7000 psi (48.3 MPa) 16 000 psi (110 MPa) 3.3 COMPRESSIVE STRENGTH, mm (ASTM D 695) 40 000 psi (276 MPa) 3.4 IMPACT STRENGTH, min (ASTM D 256, notched) 0.75 ft Ib/in (40 J/m) 3.5 HARDNESS - ROCKWELL "M", min (ASTM D 785) 105 3.6 SPECIFIC GRAVITY, mm (ASTM D 792, Method "A") 1.65 3.7 WATER ABSORPTION, max (ASTM D 570, 24 h immersion) 1.5% 3.8 SUPPLIER'S RESPONSIBILITY Material supplied to this specification must be equivalent to that originally approved. Changes in formulation or processing shall not be made without prior approval as described in Supplier Procedure I-A. Date Para No 1978 03 09 1963 10 11 Jctisr-*e7$' 3948-a HFM- 003824 Revisions Metficated and Retyped CFW-tfD 5~7/^g- !3 Released F6-1139 ________________ _____ 8061 1306 \ i Page _1_ cf JL SCF-FORD-1435 Engineering Material Specification ESF-M3D80-A 4. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure 1-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. 5A 5PAULDnd<r Fide* to ivt. P. 0. 06# t'tf og Aww AtL8*R. } high. 46(04 A-470-/ 197? 12 01 ^ 3948-b HFM - 003825 PfiOl 1307 race . Engineering Material Specification ( Material Name Specification Number ASBESTOS PAPER BASE, PHENOLIC LAMINATE - OIL RESISTANT *if VV ESW-M3D81-A 1. SCOPE X RF. The material defined by this specification is an asbestos paper base, laminate impregnated with a thermosetting resin suitable for use in oil at high temperatures. 2. ` APPLICATION This specification was released originally for material used in thrust washers for automatic transmissions. 3. REQUIREMENTS 3.1 TENSILE STRENGTH, min (ASTM D 638) With Grain Against Grain 9500 psi (66 MPa) 7000 psi (49 MPa) 3.2 FLEXURAL STRENGTH, min (ASTM D 790, flat with grain) 16 000 psi (110 MPa) 3.3 COMPRESSIVE STRENGTH, min (ASTM D 695) c 3.4 IMPACT STRENGTH, Izod, min (ASTM D 256, notched) 40 000 psi (276 MPa) 0.75 ft lb/m (40 J/m) 3.5 HARDNESS - ROCKWELL "M" (ASTM D 785) 105-111 3.6 SPECIFIC GRAVITY, mm (ASTM D 792) 1.65 3.7 OIL IMMERSION Production parts manufactured from material covered by this specification must meet the following oil immersion test. ASTM #1 Oil at 190 + 3C for 1 h. Sample shall not check, warp or blister. __ Automatic transmission fluid (M-2C33-F and ESP-M2C138-CJ) at 190 + 3C for 1 h. Sample shall not check, warp or blister. ~ Date Para No | Revisions * s c 1976 11 15 1964 01 27 ' Metricated and Retvped PC3_RI375^-0-?3______ ' Released CPS-405371 ____ 0 i > " 3948-a Page _L of _JL ROOl 1309 HFM- 003827 Engineering Material Specification ESW-M3D81--A 3.7 OIL IMMERSION Note: Suspend samples in the oil immersion bath, with bath at 93C, bring bath to 190 + 3C within 1 h. Hold at 190 + 3C for 1 h. 3.8 SUPPLIER'S RESPONSIBILITY ' Material supplied to this specification must be equivalent to that originelly approved. Changes in formulation or processing shall not be made without prior approval as described m Supplier Procedure I'a. 4. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure I-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. s (, I A 5 pftOLDiN (r Fieetjifoc fii-C,70'l U F\ U/OIOK54L OIL Woo, 701 H ( MetPtey in - C E"!.as.t 3948-ti HFM - 003828 Page u sooi mo Engineering Material Specification Mate^al Name PHENOUC COMPRESSION MOLDING COMPOUND ASBESTOS REINFORCED 1. SCOPE ft W Spec.f>caticn Numoer ESW-M3D97-A Wo ff\K7 X R6F. The material defined by this specification is a two stage, asbestos filled, high heat resistant, " molding material capable of withstanding operational temperatures in the 204C range. 2. APPLICATION This specification was released originally for material used as thrust washers in automatic transmissions. 3. REQUIREMENTS 3.1 COMPRESSION MOLDED TEST SPECIMENS (As molded without post bake.) 3.1.1 Impact Strength, Izod, min (ASTM D 256) 0.3 ft lb/in (16 J/m) 3.1.2 Specific Gravity (ASTM D 792) 1.57 - 1.59 3.1.3 Flexural Strength, min (ASTM D 790) 9500 psi (66 MPa) 3.1.4 Tensile Strength, min (ASTM D 638) 6000 psi (41.4 MPa) 3.1.5 Compressive Strength, min (ASTM D 695) 26 000 psi (179 MPa) 3.1.6 Water Absorption, max (ASTM D 570) 0.3% 3.1.7 Hardness - Rockwell "E", min (ASTM D 785) 80 - 00 no 3.1.8 Deflection Temperature, min (ASTM D 648, 264 psi (1820 kPs)) 3.1.9 Ash, min (FLTM BO 6-2) 28% . bale I l *1 i > 1965 If! 28 , Z3 3948-a Revisions Metricated and Retvoed PC3. ?IToS--3-7" Kf-lenseG CPf'-CR486859 *1 , ... d Page -1_ c' _2_ HFM - 003829 Engineering Material Specification ESW-M3D97-A 3.2 MOLDED PARTS Specific requirements for physical properties of molded parts, when required, shall be as specified on engineering drawings. 3.3 INFRARED SPECTROPHOTOMETRY Ford Motor Company, at its option, may conduct infrared analysis of material/parts supplied to this specification. The curves established for initial approval shall constitute the reference- standard and shall be kept on file at Central Laboratory. All samples shall produce curves that correspond to the reference standard when tested under the same conditions as those specified on the master curve. 3.4 SUPPLIER'S RESPONSIBILITY Material supplied to this specification must be equivalent to that original approved. Changes in formulation or processing shall not be made without prior approval as described in Supplier Procedure I-A. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the effected product engineering office. Procedure for gaming approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure 1-A. Approved ne''. suppliers will be. added to t^e Engineering Materials Approved Source List. H 550 A V OGZ A Hb>f<e/i cHfrt, cetp, pu/tez 2177 . MtLWAVKee perttiT) Mich. Hmi UN/Mj CA0l 0 fl0F/t5 T FABRIC Di\J. SouthFietoi men. itoic. 2Z0H7. 5303-BLACK ZS HFM - 003830 Pool 1312 Engineering Material Specification ( Material Name Specification Number PHENOIiC INJECTION OR TRANSFER MOLDING COMPOUND f W ESW-M3D108-A ASBESTOS REINFORCED No fART X K6F. 1. SCOPE i JFhe material defined by this specification is a two stage, asbestos filled, high heat resistant . molding material capable of withstanding operational temperatures in the 204C range. 2. APPLICATION This specification was released originally for material used as thrust washers in automatic transmissions. 3. REQUIREMENTS 3.1 INJECTION OR TRANSFER MOLDED TEST SPECIMENS (As molded without post bake.) 3.1.1 Impact Strength, Izod, min (ASTM D 256, notched) 0.3 ft lb/m (16 J/m) 3.1.2 Specific Gravity (ASTM D 792) 1.45 -1.47 3.1.3 Flexural Strength, min (ASTM D 790) 14 000 psi (97 MPa) 3.1.4 Tensile Strength, min (ASTM D 638) 7000 psi (48.3 MPa) 3.1.5 Compressive Strength, min (ASTM D 695) 28 000 psi (193 MPa) 3.1.6 Water Absorption, max (ASTM D 570) 0.3% 3.1.7 3.1.8 Hardness - Rockwell "E", min (ASTM D 785) Deflection Temperature, min (ASTM D 648, 264 psi (1820 kPa)) 85 177C 3.1.9 Ash, min (FLTM BO 6-2) - 20% Date Para. No Revisions ft. 1978 11 15i 1968 11 01 3948-a M etrmated and Retvoed PCR RD782LL0-P3 .... .............. " " --------- Released CP5-PA929042 '1 i 1 CtuAlA^'' ! Page _L ol _2_ sooi un HFM - 003831 Engineering Material Specification ESW-M3D108-A 3.2 MOLDED PARTS Specific requirements for physical properties of molded parts, when required, shall be as specified on engineering drawings. 3.3 INFRARED SPECTROPHOTOMETRY Ford Motor Company, at its option, may conduct infrared analysis of material/parts supplied to this specification. The curves established for initial approval shall ' constitute the reference standard and shall be kept on file at Central Laboratory. AH samples shall produce curves that correspond to the reference standard when tested under the same conditions as those specified on the master curve. 3.4 SUPPLIER'S RESPONSIBILITY Material supplied to this specification must be equivalent to that originally approved. Changes in formulation or processing shall not be made without prior approval as described in Supplier Procedure I-A. 4. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure I-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. U OC.Z A UUmhvJ CA0l SouTHFieLt? , HitH. 5310 1977 11 19 HFM - 003832 Page JL. of 1-- 8001 *3f<+ Engineering Material Specification Material Name Specification Number PHENOLIC, TRANSFER MOLDING COMPODND F ESF-M3D113-A FAST MOLDING - MINERAL FILLED fanesitb K.iMFc^cCP 1. SCOPE The material defined by this specification is e two stage, transfer molding grade, mineral filled, phenolic molding compound with low moisture absorption, and good dimensional .stability at elevated temperatures. 2. APPUC/TION This specification was released originally for material used in the molded commutator for starting motors. 3. REQUIREMENTS 2.1 PROPERTIES OF MOLDED MATERIAL 3.1.1 Conditioning 48 h at 50C, test at 23C + 2C ~ 3.1.2 Color The color shall be as specified on engineering drawing. 3.1.3 Specific Gravity (ASTM D 792) 1.67 - 1.71 3.1.4 Water Absorption, max (ASTM D 570) 0.2% 3.1.5 Impact Strength, min (ASTM D 256, notched) 0.58 ft lb/m (31 J/m) 3.1.6 Flexural Strength, min (ASTM D 790) 12 000 psi (83 MPa) 3.1.7 Tensile Strength, min, (ASTM D 638) 6000 psi (41.4 MPa) 3.1.8 3.1.9 Compressive Strength, min (ASTM D 695) Deflection Temperature, min (ASTM D 648, 264 psi (1820 kPa)) 20 000 psi (138 MPa) 260C Date Para. No 1978 03 09 1970 06 04 il"?? 3S48>a HFM - 003833 Metricated and Retvoed C Released F6Z-289 Revisions S& 7//_? fl00l 131S < .,, Page _i_ of Engineering Material Specification ESF-M3D113-A 4. C 5. 3.1.10 Dielectric Strength, min (ASTM D 149, 48 h at 50% R.H., 23 + 2 Short Time Step by Step 150 V/mil (5.9 kV/mm) 100 V/mH (3.9 kV/mm) 3.1.11 3.1.12 Ash, min (FLTM BO 6-2) Deformation at 76C, max (ASTM D 621, Method "A", 4000 psi (27.6 MPa), 1/8 in (3.2 mm) thick) 44% 0.40% 3.2 SUPPLIER'S RESPONSIBILITY Material supplied to this specification must be equivalent to that originally approved. Changes in formulation or processing shall not be made without prior approval as described in Supplier Procedure I-A. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure I-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. GENERAL INFORMATION Any material data included herein is for information only and is not a requirement for the supplier. 5.1 MODULUS OF ELASTICITY IN TENSION (ASTM D 638) 2.1 x 106 psi (14.5 GPa) 5.2 HARDNESS - ROCKWELL "E" (ASTM D 785) 92 5.3 MOLDING SHRINKAGE (ASTM D 955) Compression Transfer 0.0015 - 0.0035 in/in (mm/mm) 0.0035 - 0.0055 in/in (mm/mm) {o^ens C HFM- 003834 8001 1116 Page _JL of. Engineering Material Specification Material Name _ PHENOLIC, TRANSFER MOLDING COMPOUND - MINERAL FILLED ASBESTOS &BINFcC.C0 1. SCOPE ' Specification Number P ESW-M3D117-A The material defined by this specification is a two stage, transfer molding grade, mineral filled, flake phenolic molding compound with low moisture absorption, and good dimensional - stability at elevated temperatures. 2. APPLICATION This specification was released originally for material used to mold automatic transmission converter reactors. 3. REQUIREMENTS , 3.1 COMPRESSION MOLDED TEST SPECIMENS (As molded without post bake.) 3.1.1 Color Black 3.1.2 Specific Gravity (ASTM D 792) 1.74 -1.80 3.1.3 Water Absorption, max (ASTM D 570) 0.5% 3.1.4 Impact Strength, min (ASTM D 256, notched) 1.2 ft Ib/rn (64 J/m) 3.1.5 Flexural Strength, min (ASTM D 790) 9500 psi (65 MPa) 3.1.6 Tensile Strength, min (ASTM D 638) 4700 psi (32.4 MPa) 3.1.7 Compressive Strength, min (ASTM D 695) 20 000 psi (138 MPa) 3.1.8 Deflection Temperature, min (ASTM D 648, 264 psi (1820 kPa)) 260C 3.1.9 Ash, min (FLTM BO 6-2) 48% 3.1.10 Hardness - Rockwell "E", min (ASTM D 785) 90 bate Para. No Revisions C 1978 11 15 1971 09 27 EJunon*"7*7 ***** Metricated and RetvDedPCR mr7fi3UUo..T>3_______ Released CP5-971708 O Page _L of _2_ 8001 1317 HFM - 003835 Engineering Material Specification ESW-M3D117-A 3.1.11 Infrared Spectrophotometry Ford Motor Company, at its option, may conduct infrared analysis of material/parts supplied to this specification. The curves established for initial approval shall constitute the reference standard and shall be kept on file at Central Laboratory. All samples shall produce curves that correspond to the reference standard when tested under the same conditions as those specified on the master curve. 3.1.12 Physical and/or Performance of Finished Product When required, shall be as specified on the affected part or product engineering drawing, or in the affected part or product engineering performance specification. . 3.2 SUPPLIER'S RESPONSIBILITY Material supplied to this specification must be equivalent to that originally approved. Changes in formulation or processing shall not be made without prior approval as described m Supplier Procedure I-A. 4. APPROVAL OP SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure I-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. - (fth Key 1977 11 21 HFM - 003836 Page 2-- of _2 0Q01 1318 mwssm Engineering Material Specification Material Name Specification Number r \ MILLBOARD, ASBESTOS-RIGID-HEAT INSULATOR 1. SCOPE ESR-M2E57-A V ESB-M2E57-B NO r/\Kt X KEF, The material defined by this specification is a rigid asbestos millboard of uniform compo sition. 2. .APPLICATION This specification was released originally for material used as a heat insulator between the floor pan and the exhaust system. 3. REQUIREMENTS 3.1 CONDITIONING All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 + 2C and 50 + 5% relative humidity for 24 h prior to testing and tested under the same controllecTconditions. 3.2 WEIGHT, min (ASTM D 461) 1.15 lb/ft2 (5.62 kg/m2) 3.3 THICKNESS 0.245-0.285 in (6.22-7.24 mm) c (ASTM D 461, except use 1.0 in (25 mm) diameter foot, 1 lb (454 g) total load) 3.4 TENSILE STRENGTH, min (ASTM D 638, except sample size shall be 0.5 x 6.0 in (13 x 152 mm) WMD AMD 550 psi (3.8 MPa) 200 psi (1.4 MPa) 3.5 FLEXURAL STRENGTH, min (ASTM D 790, except sample size is 2 x 6 in (51 x 152 mm) with 4.0 in (102 mm) span) 3.5.1 Normal WMD AMD 1000 psi (6.9 MPa) 500 psi (3.5 MPa) ; bate I Para i No Revisions 1978 09 11 !____________ ___ Metricated. Renumbered & Retyped CAHI-RD572G66-7 1971 08 17 i Released V ESB-M2E57-B AB1-302-14 11963 08 08 Released ESB-M2E57-A AS1-1023 3948-a 8001 1319 i v 41 i Page _L of _iL HFM - 003837 msmfm Engineering Material Specification V ESB-M2ES1-B 3.5.2 Wet WMD AMO 500 psi (3.5 MPa) 500 psi (3.5 MPa) Test Method: Immerse sample in water for 16 h at 23 + 2C. Blot specimens with paper towelling. 3.5.3 After Cycling WMD AMD 500 psi (3.5 MPa) 250 psi (1.75 MPa) Test Method: As described under para 3.6. 3.6 CYCLING TEST No evidence-of distortion, delamination or warping. Test Method: Sample sizes shall be as outlined under para 3.5. The specimens shall be exposed to 3 complete cycles of the following. . 2 h water immersion at 23 + 2C . 3 h at -34 C " . 3 h at 82 + 3C 3.7 WATER ABSORPTION, max (FLTM BS 4-1, Method "A", 2 h total immersion) 60.0% 3.8 VESB-M2E57-B FLAMMABILITY V 3.8.1 In order to comply with Federal Motor Vehicle Safety Standard No. 302, " the materials, portions of components, and composites shall not burn, or transmit a flame across its surface, at a rate of more than 4 in (101 mm) per min. To demonstrate compliance, the sample size and method of testing shall be in accordance with FLTM BN 24-2. 3.8.2 Performance - Environmental Aging All materials, portions of components, and composites defined by this specification that have not been treated, modified or reformulated and exceed a max burn rate of 3.0 m (76 mm) per min as specified by the Flammability Lot Sampling Plan of FLTM BN 24-2, must be evaluated for permanency of the materials' flame retardant properties per ESB-M25P3A according to the accelerated environmental aging requirements applicable to the basic material category of this particular specification. Any material, portions of components, and composites defined by this specif.cation that have been treated, modified or reformulated to conform to Flammability Lot Sampling Plan of FLTM BN 24-2, regardless of max burn rate, must be evaluated for both permanency of materials' flame retarcant properties and changes in mechanical, chemical and physical properties per ESB-M25P3-A applicable to the basic materials category of this particular specification. 8001 1320 Page JL of JL HFM- 003838 Engineering Material Specification ESB-M2E57-A V ESB-M2E57-B 3.8.3 Flammability Test Program Materials, portions of components, and composites governed by this specification must also comply with the requirements of VES-D3AB11014-AA. 3.9 SUPPLIER'S RESPONSIBILITY `' Material supplied to this specification must be equivalent to that originally approved. Changes in formulation or processing shall not be made without prior approval as described in Supplier Procedure I-A. 4. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure I-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. G 013 A ? 03Z A 6A F IMOuSTJt//\ C z i </oo H WAtl/UfAi, MaH, inio "313-1SL- 7.SL5 PAMAC6N] LOfLf. fUitup tAney co. s. u/AY/ue ciwc/uwatij ohio 513~ $Z)-3>06 E-IOH 1978 08 110/M- srs 39484. v HFM - 003839 flOfil 1321 Page of ^ Engineering Material Specification Material Name SEALER, ENGINE AND CHASSIS - HEAVY SEALER, ENGINE AND CHASSIS - MEDIUM SEALER, ENGINE AND CHASSIS - LIGHT JtxE / Jr l JjEI Specification Number ESE-M4G114-A ESE-M4G115-A ESE-M4G116-A 1. SCOPE The materials defined by these specifications are asbestos filled vegetable oil type sealers which will dry without becoming hard and brittle and are resistant to oil, water, and engine coolant solutions. 2. APPLICATION These specifications were released originally for materials used for sealing studs, plugs, gaskets, and joints in the engine and chassis assemblies to prevent leakage of lubricant or ? coolant. They are applied by flowing, dipping, brushing, or roll-coating. ^? 3. REQUIREMENTS 3.1 VISCOSITY, s (FLTM BU 4-1, 4 hole disc) As Received Aged, max ESE-M4G114-A, 250 g load ESE-M4G115-A, 100 g load ESE-M4G116-A, 100 g load 45 - 55 20 - 25 10-15 100 60 35 3.2 SOLIDS, % min (2 + 0.5 g sample, heat at 102 + 3' m a mechanical convection oven for 3 h) ESE-M4G114-A ESE-M4G115-A ESE-M4G116-A 80 70 65 3.3 FLASH POINT, min (ASTM D 1310) 46C 3.4 WEIGHT PER VOLUME (ASTM D 816) 8-9 lb/gal (0.96 - 1.08 kg/L) The weight tolerance for any one supplier shall be + 0.2 lb/gal (0.02 kg/L) based on the recorded weight of his original approved production sample. 1.5 QUALITY Shall be a smooth homogeneous mixture free from foreign materials and properties detrimental to normal production use. lOOfa Date Para. No ' Revisions 1963 08 09 Meficated and RetvDed CEVt-Tfi Released r.7-2756 y . Page _L_ of _2_ HFM - 003840 |) Engineering Material Specification C3IrMr5`tu I i *i-rt ESE-M4G115-A ESE-M4G116-A 3.6 RESISTANCE TO INITIAL FILL ENGINE OIL (FLTM BV 6-1, 72 h) Shall prevent leakage of oil from the test assembly. 3.7 RESISTANCE TO ENGINE COOLANT SOLUTIONS " Any evidence of Coolant leakage during the 72 h test period shall be recorded as a ` material failure. Test Method: Follow test method outlined under para. 3.R, except fill the assembly with a 50/50 mixture of initial fill engine coolant concentrate, ethylene glycol, and water. ' 3.8 SUPPLIER'S RESPONSIBILITY Material supplied to this specification must be equivalent to that originally . approved. Changes in formulation or processing shall not be made without prior approval as described in Supplier Procedure I-A. 4. APPROVAL OF SUPPLIERS Suppliers to this specification must be approved by the affected product engineering office. Procedure for gaining approval of a specific material to a new/existing ES-M specification is contained in Supplier Procedure I-A. Approved new suppliers will be added to the Engineering Materials Approved Source List. 5. GENERAL INFORMATION This information is for direction of the user and is not a requirement for the supplier. 5.1 FLAMMABILITY AND/OR TOXICITY This materia) represents a potential fire and/or health hazard. The Manufacturing Engineering Department shall notify both the Plant Security and the Safety Units of its presence in the Plant to assure that proper fire and/or health precautions are provided. The location in which it is used or stored shall be included in the notification. A 2/1 A ft0.6, MF&. Co.j imc. 2o zi tftviioe OAK0oevt MiCfi. 8123 , \ 1 ? ZlH A p ill A PEKMATE/X: CO. j/AJC. et* i? so k/ r/UM dcACfi, FL. ?3yo2 3oS- CFG - 0280 Fierce r stevekjs cnett, co^f, 7io oil|0 5T. BUFFALO , Wcf, l*jzo3 8001 i'323 X t ti, X* , 5! ? ' C 1107, C15HI, ?6ZZ page _JL of__? HFM - 003841