Document Mo0Re3z7xN5QDEqX5v5ngBK9k

PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 1 OF 20 CHLORINE GAS ( DRY LESS THAN 20 PPM WATER ) CLASS 300 440. PSIG AT 275. DEG. F TO -20. DEG. F TEST CLASS & PRESS: C @ 660 MATERIAL: CARBON STEEL CORROSION ALLOWANCE: .0625 INCHES INDUSTRY PIPING CODE: ASME B31.3-1990 EDITION ITEM SIZE DESCRIPTION NOTES NOTE <n> NOTE <n> NOTE <n> N7 37 NOTE <n> NOTE <n> CAUTION CAUTION INSPECTION INSPECTION PRESSURE AND TEMPERATURE LIMITING FACTORS ARE LARGE BRANCH CONNECTIONS AT 440 PSIG. THIS PIPING SPEC CONFORMS TO PIPING CODE ASME B31.3, NORMAL SERVICE, IN REGARDS TO INTERNAL PRESSURE AND TEMPERATURES STATED ABOVE IN HEADER DESCRIPTION. CHECK COMPLETED ON 08/12/92. ADDITIONAL APPLICABLE CODE EVALUATIONS SHOULD BE PERFORMED AT THE PROJECT LEVEL FOR CONDITIONS SUCH AS EQUIPMENT NOZZLE LOADINGS, STRESSES DUE TO THERMAL EXPANSIONS, WEIGHT, LIQUID EXPANSION, ETC. TITANIUM METAL REACTS CATASTROPHICALLY WITH DRY CHLORINE. DO NOT USE TITANIUM METAL COMPONENTS IN THIS SERVICE. PIPING ON THIS SPECIFICATION SHALL BE ALL WELDED AND/OR FLANGED INCLUDING THE FIRST BLOCK VALVE OFF THE LINE IN INSTRUMENT PIPING AND ALL VENT AND DRAIN VALVES. 10% OF ALL CIRCUMFERENTIAL BUTT AND MITER GROOVE WELDS SHALL BE RANDOM RADIOGRAPHED. ACCEPTANCE SHALL BE IN ACCORDANCE WITH SEVERE CYCLIC CONDITIONS CRITERIA 5% OF ALL.SOCKET WELDS SHALL BE SPOT RADIOGRAPHED TO VERIFY CORRECT SOCKET GAP AND WELD QUALITY LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046786 OONFTDFNTTAt PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM NOTE <n> SIZE INSPECTION NOTE <n> WELDING NOTE <n> WELDING NOTE <n> NOTE <n> N93J NOTE <n> N93A N245 CLEANING CLEANING CLEANING N238 CAUTION PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 2 OF 20 DESCRIPTION VISUAL INSPECTION IS REQUIRED IN ACCORDANCE WITH CODE CRITERIA FOR 'NORMAL'CATEGORY SERVICE. WELDING AND FABRICATION SHALL BE IN ACCORDANCE WITH DOW SPECIFICATION L8S-6500-01. APPLICABLE DOW WELDING PROCEDURES: SHOP FABRICATION - L8S-6501-AZ, L8S-6501-BQ AND L8S-6501-AP; FIELD FABRICATION L8S-6501-BQ , L8S-6501-DV AND L8S-6501-CB. PIPING SHALL BE INSTALLED IN ACCORDANCE WITH ENGINEERING SPECIFICATION L4S-4210-01 AND TESTED PER ENGINEERING SPECIFICATION L4S-6410-01. FLANGE BOLTING SHALL BE INSTALLED IN ACCORDANCE WITH DOW ENGINEERING SPECIFICATION L5C-3800-00, BOLT TORQUE TABLE #4. ALL PIPING TO BE DEGREASED PRIOR TO ASSEMBLY. FOR SPECIFIC CLEANING INSTRUCTIONS, PLEASE REFER TO PROJECT SPECIFICATIONS. ALL VALVES SHALL BE DEGREASED, SEALED AND TAGGED AT FACTORY FOR CHLORINE SERVICE. SEE ENGINEERING SPECIFICATION N4S-9803-01 FOR ACCEPTABLE MANUFACTURERS OF PIPE AND PIPING COMPONENTS. CAUTION: CHLORINE LINES SHALL BE PLACED IN THE PIPEWAYS SO THAT NO LINES CARRYING CORROSIVE MATERIALS SHALL PASS OVER THEM. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046787 f ONFTDFNTT Ai. PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM NOTE <n> SIZE N840 NOTE <n> PIPE P28B P3BW NOTE <n> PIPE NIPPLES PN28BSW PN28BSWXL CAUTION 1/2 - 1 1/2 2-16 1/2 - 1 1/2 1/2 - 1 1/2 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 3 OF 20 DESCRIPTION PROVIDE WELDED .PIPE SHOES FOR ALL BUTT WELDED PIPING AT PIPE SUPPORTS. WEAR PLATES ARE PROHIBITED. AVOID THE USE OF BOLTED SHOES, CLEVIS, AND U-BOLT TYPE SUPPORTS. SEAL WELDED PLATE LUGS ARE PREFERRED FOR ATTACHMENT OF PIPE HANGERS TO PIPE MACHINE FLARED LAP (VANSTONE) JOINTS ARE NOT PERMITTED ON THIS PIPING SPECIFICATION. DO NOT ROUTE PIPE SIZES SMALLER THAN 2" IN PIPE RACKS. PIPE: EXTRA STRONG; SEAMLESS; ASTM A 106 GR B; CARBON STEEL. PIPE: STANDARD WEIGHT; ERW; ASTM A 53 TYPE E GR B OR API 5L GR B; CARBON STEEL. P27B IS AN ACCEPTABLE SUBSTITUTE FOR P3BW. PIPE NIPPLE: EXTRA STRONG; SEAMLESS; ASTM A 106 GR B; CARBON STEEL; 3 IN LONG; PLAIN ENDS. PIPE NIPPLE: EXTRA STRONG; SEAMLESS; ASTM A 106 GR B; CARBON STEEL; 6 IN LONG; PLAIN ENDS. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 D0 A 046788 C ONFT UFNTT Al PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM SIZE BRANCH CONNECTIONS PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 4 OF 20 DESCRIPTION BC1 HEADER SIZE NINETY DEGREE BRANCHES SHALL BE DESIGNED AND INSTALLED IN ACCORDANCE WITH THE FOLLOWING TABULATION: BRANCH SIZE BRANCH SAME AS HEADER OR SMALLER CONNECTION NOTE <n> FITTINGS 1/2 - 1 1/2 3/4 - 1 1/2 2 - 14 2 - 14 3 - 10 12 - 16 1/2 - 1 1/2 1/2 - 1 1/4 2 - 14 1/2 - 1 2-8 10 - 14 1/2 SAME SMALLER SAME SMALLER SMALLER SMALLER TEE RED.TEE OR TEE SWAGE TEE SOCKOLET PLAIN STUB-IN RED.TEE OR WOL E64 L64 T64 TR64 PC2 7 1/2 - 1 1/2 1/2 - 1 1/2 1/2 - 1 1/2 1/2 - 1 1/2 1/2 - 1 1/2 ELBOW 90 DEG: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. ELBOW 45 DEG: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. TEE: SOCKET WELDING; CLASS 3000; FORGED ASTM A 105; CARBON STEEL; ASME B16.ll. TEE REDUCING: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. CAP: SOCKET WELDING; CLASS 3000; FORGED ASTM A 105; CARBON STEEL; ASME B16.ll. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 00 A 0 4 (S 7 5 CONF T DFNT T Al PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM PC2 SIZE 1/2 - 1 RC22P 1/2 - 1 1/2 RE22P 1/2 - 1 1/2 RC22BP 1/2 - 2 RE22BP 1/2 - 2 C14C C14S 1/2 - 1 1/2 1/2 - 1 1/2 C42 1/2 - 1 1/2 PIPING SPEC CODE; L103 DATE: 02-11-94 PAGE: 5 OF 20 DESCRIPTION PLUG HEX HEAD; THREADED; FORGED; ASTM A 105; SOLID CARBON STEEL; ASME-B16.il AND ANSI B1.20.1. SWAGED NIPPLE CONCENTRIC: PLAIN BOTH ENDS; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL. SWAGED NIPPLE ECCENTRIC: PLAIN BOTH ENDS; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL. SWAGED NIPPLE CONCENTRIC: BEVELED LARGE END, PLAIN SMALL END; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL. SWAGED NIPPLE ECCENTRIC: BEVELED LARGE END, PLAIN SMALL END; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL. COUPLING: SOCKET WELDING; CLASS 3 000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. STRAIGHT TYPE O-LET BRANCH: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL. ASME B16.ll. ANVIL (CANVIL) ANVILET BONNEY FORGE SOCKOLET WFI INTERNATIONAL, INC. SOCKET WELD PIP PENNSYLVANIA MACHINE WORKS SOCKET WELD PHOENIX SOCKET WELD TRANS-O-CON STRAIGHT TYPE O-LET BRANCH: BEVELED ENDS; EXTRA STRONG; FORGED; ASTM A 105; CARBON STEEL; ASME B16.9. ANVIL (CANVIL) BUTT WELD ANVILET BONNEY FORGE WELDOLET PENNSYLVANIA MACHINE WORKS BUTT WELD OU PHOENIX TRANS-O-CON BUTT WELD CONNECTIC WFI INTERNATIONAL, INC. BUTT WELD PIPET LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046790 CONFT OrNT TA PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM C3ESW SIZE 1/2 - 1 1/2 C54SW ** C54SWXL 1/2 - 1 1/2 1/2 - 1 1/2 C41E 2-4 C41 2-16 E15B 2-16 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 6 OF 20 DESCRIPTION ELBOW TYPE O-LET BRANCH: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. ANVIL (CANVIL) ELBOW ANVILET BONNEY FORGE ELBOLET PENNSYLVANIA MACHINE WORKS ELBO OUTLET PHOENIX TRANS-O-CON ELBOW CONNECTION WFI INTERNATIONAL, INC. ELBO PIPET NIPPLE TYPE O-LET BRANCH: PLAIN END; EXTRA STRONG; FORGED; ASTM A 105; CARBON STEEL; 3 1/2 INCH LONG. BONNEY FORGE NIPOLET PENNSYLVANIA MACHINE WORKS NIPPLE OUTLE WFI INTERNATIONAL, INC. NIPPLE PIPET NIPPLE TYPE O-LET BRANCH: PLAIN END; EXTRA STRONG; FORGED; ASTM A 105; CARBON STEEL; 6 1/2 INCH LONG. BONNEY FORGE NIPOLET PENNSYLVANIA MACHINE WORKS NIPPLE OUTLE WFI INTERNATIONAL, INC. NIPPLE PIPET ELBOW TYPE O-LET BRANCH: BUTT WELDING; STANDARD WEIGHT; FORGED; ASTM A 105; CARBON STEEL; ASME B16.9. ANVIL (CANVIL) ELBOW ANVILET BONNEY FORGE ELBOLET PENNSYLVANIA MACHINE WORKS ELBO OUTLET WFI INTERNATIONAL, INC. ELBO PIPET STRAIGHT TYPE O-LET BRANCH: BUTT WELDING; STANDARD WEIGHT; FORGED; ASTM A 105; CARBON STEEL; ASME B16.9. ANVIL (CANVIL) BUTT WELD ANVILET BONNEY FORGE WELDOLET PENNSYLVANIA MACHINE WORKS BUTT WELD OU PHOENIX TRANS-O-CON BUTT WELD CONNECTIO WFI INTERNATIONAL, INC. BUTT WELD PIPET ELBOW 90 DEG LR: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046791 CONFIDENT! Al PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM L15B SIZE 2-16 T15B 2-16 TR15B 2-16 RC15B 2-16 RE15B 2-16 X15B 2-16 PC51B 2-16 FLANGES F25RF80 1/2 - 1 1/2 F5RFSTD 2-16 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 7 OF 20 DESCRIPTION ELBOW 45 DEG: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. TEE: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. TEE REDUCING: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. REDUCER CONCENTRIC: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. REDUCER ECCENTRIC: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. CROSS: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. CAP: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9. FLANGE: SOCKET WELDING; CLASS 300; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5. BORE TO MATCH SCHEDULE 80. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. FLANGE: WELDING NECK; CLASS 300; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5; BORE TO MATCH STANDARD WEIGHT. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 C0NF?D?N?m PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM F7RF SIZE 1/2 - 16 GASKETS G34A 1/2-16 FASTENERS BA193B7QC BA193B7QCSC PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 8 OF 20 DESCRIPTION FLANGE: BLIND; CLASS 300; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. GASKET: SPIRAL-WOUND; MONEL 400 WINDING; TEFLON FILLER; 0.175 INCH THICK; API 601 FOR ASME/ANSI B16.5 FLANGES; CARBON STEEL CENTERING RING; MONEL INNER RING. FLEXITALLIC CGI FURON RW LAMONS WRI STERLING GR-IR COATED STUD BOLT: ASTM A 193 GR B7; LIQUID QUENCHED AND TEMPERED; ALLOY STEEL; WITH ASTM A 194 GR 2H HEAVY HEX NUTS. STUD BOLTS AND NUTS TO BE FLUOROPOLYMER COATED, COLOR TO BE BLUE. FLUOROPOLYMER COATING TO BE AS SUPPLIED BY STANCO BOLT DIVISION, METALS COATING CORP., PROTECTIVE COATINGS INC., OR INDUSTRIAL METAL FINISHING CO. COATED CAP SCREW: ASTM A 193 GR B7; LIQUID QUENCHED AND TEMPERED; ALLOY STEEL. CAP SCREWS TO BE FLUOROPOLYMER COATED, COLOR TO BE BLUE. FLUOROPOLUMER COATING TO BE AS SUPPLIED BY STANCO BOLT DIVISION, METALS COATING CORP., PROTECTIVE COATINGS INC., OR INDUSTRIAL METAL FINISHING CO. LAST UPDATE 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046793 CONFTDFNTT Ai PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM BOLT LUBRICANT SIZE BL10 NOTE <n> VALVES VG300CS5ARF 2-16 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 9 OF 20 DESCRIPTION BOLT LUBRICANT: PASTE, NICKEL BASED, ANTISEIZE COMPOUND. FEL PRO NICKEL EASE FEDERAL PROCESS CO. THRED-GARD NICKEL NEVER SEEZ NICKEL SPECIAL BOLT LUBRICANT IS REQUIRED ONLY WHEN FLUOROPOLYMER COATING IS DAMAGED, OR WHEN REUSING EXISTING NON-COATED BOLTS. GATE VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; OS&Y, RISING STEM, FULL PORT TYPE; BOLTED BONNET; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; HASTELLOY C STEM; FLEXIBLE WEDGE DISC; SEAT INSERTS, PTFE; PTFE STEM SEALS OR PACKING; PREPARED FOR CHLORINE SERVICE AT FACTORY; ASME B16.5/B16.47 SERIES A; API 600 THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. KITZ 300 SCL NEWCO 13F-CB9CL LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 00 A 046.794 OONFTDFNTTA1 PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM VGL300LC10ARF SIZE 1/2 - 1 VGL3 OOLC11ARF 1 1/2 - 12 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 10 OF 20 DESCRIPTION GLOBE VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 350 GR LF2; FORGED LOW TEMPERATURE CARBON STEEL BODY; BELLOWS TYPE; BOLTED BONNET; ASTM A 320 GR L7 LIQUID QUENCHED & TEMPERED BOLTING; PTFE GASKET; HASTELLOY C STEM; HARD FACED DISC; HARD FACED SEATING;; BELLOWS, FORMED MULTI-LAYER HASTELLOY C; BELLOWS HOLDER, HASTELLOY C; PTFE PACKING,* ASME B16.5; POSITION INDICATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY,* FOR LOW EMISSION SERVICE; FOR CRYOGENIC SERVICE; WARNING! THIS VALVE HAS BALL VALVE FACE TO FACE DIMENSIONS; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. ALL MATERIALS OF CONSTRUCTION TO BE SUITABLE FOR SERVICE TO -50 DEG F. DESCOTE 2100B/BVF GLOBE VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 352 GR LCC; CAST LOW TEMPERATURE CARBON STEEL BODY; BELLOWS TYPE; BOLTED BONNET; ASTM A 320 GR L7 LIQUID QUENCHED & TEMPERED BOLTING; PTFE GASKET; HASTELLOY C STEM; HARD FACED LOW TEMPERATURE CARBON STEEL DISC; HARD FACED SEATING; BELLOWS, FORMED MULTI-LAYER HASTELLOY C; BELLOWS HOLDER, HASTELLOY C; PTFE PACKING; ASME B16.5; POSITION INDICATOR; FOR LOW EMISSION SERVICE; PREPARED FOR CHLORINE SERVICE AT FACTORY; FOR CRYOGENIC SERVICE; ALL MATERIALS OF CONSTRUCTION TO BE SUITABLE FOR SERVICE TO -50 DEG F. WARNING! THIS VALVE HAS BALL VALVE FACE TO FACE DIMENSIONS; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. DESCOTE 2102B/BVF LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046795 00N5TDFNT T A( PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM VC300CS16ARF SIZE 2-16 VB300CS45ARF 1/2 - 4 NOTE <n> PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 11 OF 20 DESCRIPTION CHECK VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; SPRING ASSISTED LIFT DISC TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BODY BOLTING; SPIRAL WOUND 304SS/PTFE'BODY GASKET; SPRING, INCONEL; ALLOY 20 TRIM;.5 PSIG CRACKING PRESSURE; ASME B16.5; PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. DURABLA EXCALIBUR BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; ALLOY 20 STEM; ALLOY 20 BALL; REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; 1 INCH AND UNDER SHALL HAVE ROUND OR OVAL HANDWHEEL; 1 1/4 INCH THRU 4 INCH SHALL HAVE LEVER OPERATOR. WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY "HANDLE FOR INSULATED SERVICE"; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5300 KITZ 300 SCTA NIBCO 530 TBV 1200 VELAN F-10402 WATTS 1500 WORCESTER 52V19 HOLLOW BALL NOT ACCEPTA VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046796 CONFTDFNTTAl PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM VB300CS46ARF SIZE 6-10 NOTE <n> VB300CS61ARF 1/2 - 4 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 12 OF 20 DESCRIPTION BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; ALLOY 20 STEM; ALLOY 20 BALL; REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; WEATHERPROOF GEAR OPERATOR. THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5300 KITZ 300 SCTA NIBCO 530 TBV 1200 VELAN F-10402 WKM 310C-RB120 WORCESTER 52VI9 HOLLOW BALL NOT ACCEPTA VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE. VENTED BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 352 GR LCB; CAST CARBON STEEL BODY; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; HASTELLOY C STEM; HASTELLOY C BALL; PRESSURE RELIEVING REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; 1 INCH AND UNDER SHALL HAVE ROUND OR OVAL HANDWHEEL; 1 1/4 INCH THRU 4 INCH SHALL HAVE LEVER OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY "HANDLE FOR INSULATED SERVICE"; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5300C LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046797 OONFTDFNTTA! PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM VB3 00CS61BRF SIZE 6-10 VBF300AY2AWT 3-6 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 13 OF 20 DESCRIPTION VENTED BALL VALVE: CLASS 300; RAISED FACE; FLANGED; ASTM A 352 GR LCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; HASTELLOY C STEM; HASTELLOY C BALL; PRESSURE RELIEVING REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; WEATHERPROOF GEAR OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5300C NIBCO 530 BUTTERFLY VALVE: CLASS 300; RAISED FACE TAPPED LUG; ASTM A 351 GR CN7M; ALLOY 20 BODY; ALLOY 20 (UNS N08020) BOLTING; ALLOY 20 STEM; DISC ALLOY 20; PTFE SEATING; PTFE PACKING; BOLTED PACKING GLAND; THROTTLING LOCKING LEVER OPERATOR; THE FINISH OF THE GASKET CONTACT FACES OF THE END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. 8-THREAD SERIES BOLTS ARE REQUIRED WHEN THE FLANGE BOLT DIAMETER IS 1 1/8 INCH OR LARGER; THIS VALVE SHALL NOT BE USED FOR DEAD END SERVICE. SIDE OF VALVE.) DEZURIK BHP,L2,AA,TC,AA-AA-FT-TT,UR*LT DURCO MXL322M-0 FLOWSEAL 3LA 444 TTX-L JAMESBURY 830L-11-3500TT XOMOX 813--0-0--0-ST1--L--X LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DC A 048798 CONFTDFNTTAI PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 14 OF 20 ITEM SIZE DESCRIPTION VBF3 00AY2BWT 8-16 BUTTERFLY VALVE: CLASS 300; RAISED FACE; TAPPED LUG; ASTM A 351 GR CN7M; ALLOY 20 BODY; ALLOY 20 (UNS N08020) BOLTING; ALLOY 20 STEM; DISC ALLOY 20; PTFE SEATING; PTFE PACKING; BOLTED PACKING GLAND; WEATHERPROOF GEAR OPERATOR; THE FINISH OF THE GASKET CONTACT FACES OF THE END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5; 8-THREAD SERIES BOLTS ARE REQUIRED WHEN THE FLANGE BOLT DIAMETER IS 1 1/8 INCH OR LARGER; LARGER THAN 24 INCH, FLANGE DRILLING PER ASME B16.47 SERIES A; THIS VALVE SHALL NOT BE USED FOR DEAD END SERVICE. SIDE OF VALVE.) DEZURIK BHP,L2,AA,TC,AA-AA-FT-TT,UR*HD DURCO MXL322M-1 FLOWSEAL 3LA-444TTX-3 JAMESBURY 830L-11-3500TT W/MA XOMOX 813-0-0-0-ST1--G-X ***************************************************************************** INSTRUMENTATION NOTES N101 N7033 NOTE <n> N7022 THE FOLLOWING SPECIFICATIONS ARE TO BE USED FOR INSTRUMENTATION. FOR ITEMS NOT LISTED, THE PRECEDING PIPING SPECIFICATION IS TO BE USED WHERE APPLICABLE. INSTRUMENT PIPING IS DEFINED AS THAT PIPING FROM THE FIRST BLOCK VALVE OFF THE PROCESS LINE (NOT INCLUDING THE VALVE) TO THE INSTRUMENT. VALVES SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE. ALL SMALL INSTRUMENT CONNECTIONS SHALL BE IN AN EASILY ACCESSIBLE LOCATION. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 On a 0467qq OONF t pipN/r PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 15 OF 20 ITEM N7003 NOTE <n> N7302 SIZE 1/2 IN. SW DESCRIPTION FLOW (ORIFICE) TAPS: ORIFICE TAPS ON VAPOR LINES SHALL BE MOUNTED ON THE TOP. TAPS TO ORIFICE FLANGES SHALL BE 1/2" SOCKET WELD. NOTE <n> ORIFICE PLATES SHALL BE HASTELLOY C OR MONEL CONSTRUCTION, AND MEET OR EXCEED ANSI/API 2530 (A. G. A. REPORT # 3) FOR SHAPE, FINISH, BEVELING AND THICKNESS. N7 004 NOTE <n> PRESSURE TAPS: 1 1/2 IN. RFF. TAP ORIENTATION SHALL BE VERTICAL, TOP OF HORIZONTAL LINE, FOR GAS SERVICE, AND SIDE OF PIPE FOR HORIZONTAL LINES IN LIQUID SERVICE. NOTE <n> TAPS SHALL BE LINE SIZE ON PIPE SMALLER THAN 11/2 INCH. N7005 N7460 TEMPERATURE TAPS: THERMOWELLS SHALL HAVE A MINIMUM 0.26 INCH I.D. N7402 <n> 11/2" SW/RFF TAP ORIENTATION FOR THERMOWELLS SHALL BE SUCH THAT THE INSERTED WELL FACES AGAINST OR IS PERPENDICULAR TO THE DIRECTION OF FLUID FLOW. THERMOWELLS SHALL BE OF HASTELLOY C CONSTRUCTION. N7 007 OTHER TAPS: NOTE <n> 1-1/2 IN. RFF ANALYZER TAP ORIENTATION SHALL BE VERTICAL, TOP OF HORIZONTAL LINE. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE L103 DO A 046800 CONFIDENTIAL PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM NOTE <n> SIZE NOTE <n> N7025 TUBING PT105 CAUTION 1/4 - 1/2 PIPE NIPPLES PN8 1/2 - 1/2 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 16 OF 20 DESCRIPTION ALL PROCESS WETTED INSTRUMENTATION COMPONENTS SHALL BE OF THE FOLLOWING CONSTRUCTION: BODY HALVES OR CASES: HASTELLOY C SENSOR ELEMENTS: HASTELLOY C DIAPHRAGMS: TANTALUM GASKETS: REINFORCED TEFLON O-RINGS AND SEALS: REINFORCED TEFLON SENSOR FILL FLUID: FLUOROLUBE FOR REMOTE SEAL FLANGED LEVEL APPLICATIONS, USE G39 GASKET ON THE PROCESS WETTED SIDE. INSTRUMENTS NOT CLOSE COUPLED TO THE PROCESS SHALL BE CONNECTED BY TUBING. IF PIPE IS USED IT SHALL BE 1/2". TUBING: 0.035 IN WALL; ANNEALED; SEAMLESS; ASTM B 165 (UNS N04400); MONEL 400. HARDNESS NOT TO EXCEED HRB 75, TUBING TO BE SUITABLE FOR BENDING AND FLARING, FREE OF SCRATCHES AND WITH AN EXTERIOR SURFACE THAT HAS A FINISH OF 32 MICROINCH RA. OR BETTER, MEASURED IN EITHER THE LONGITUDINAL OR CIRCUMFERENTIAL DIRECTION, AT ANY POINT ON THE TUBING. OUTSIDE DIAMETER TOLERANCE TO BE -0.0015 INCH AND+0.0045 INCH. PIPE NIPPLE: BAR STOCK; 0.328 INCH I,D.; EXTRA STRONG WALL ASTM B 165; (UNSN04400); MONEL; 3 INCH LONG; THREADED ENDS. COLLINS INSTRUMENT CO. 133-0003-MON LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046801 CONFTDFNTIAl PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM PN8A SIZE 1/2 - 1/2 FITTINGS FT105C N7021 N7001 1/4 - 1/2 CAUTION PC2 E5 T5 1/4 - 1 1/4 - 1 1/4 - 1 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 17 OF 20 DESCRIPTION PIPE NIPPLE: BAR STOCK; 0.328 INCH I.D.; EXTRA STRONG WALL ASTM B 165; (UNSN04400); MONEL; 6 INCH LONG; THREADED ENDS. COLLINS INSTRUMENT CO. 133-0006-MON TUBING FITTINGS: MONEL. HOKE GYROLOK INTERCHANGING OF COMPRESSION FITTING PARTS OF DIFFERENT MANUFACTURES SHALL NOT BE ALLOWED. WARNING! CORRECT ASSEMBLY AND INSTALLATION OF TUBE CONNECTIONS IS CRITICAL! SWAGELOK TUBE CONNECTIONS SHALL BE ASSEMBLED AND INSTALLED AS PER SWAGELOK INSTALLATION INSTRUCTIONS. WHEN ASSEMBLY AND INSTALLATION IS COMPLETE, ALL SWAGELOK TUBE CONNECTIONS SHALL BE CHECKED AND INSPECTED FOR PROPER 'PULL-UP' WITH THE APPROPRIATE SWAGELOK INSPECTION GAGE. TUBE CONNECTIONS SHALL INCLUDE FITTINGS AND VALVES. PLUG HEX HEAD; THREADED; FORGED; ASTM A 105; SOLID CARBON STEEL; ASME B16.ll AND ANSI Bl.20.1. ELBOW 90 DEG: THREADED; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. TEE: THREADED; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 04680? C0NFTDFNTTA1 PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM FLANGES SIZE F21RRF JOINT COMPOUND JC18 JC15 VALVES VIB2 000MO8 VIG6000M01 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 18 OF 20 DESCRIPTION FLANGE: REDUCING; THREADED; CLASS 300; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JOINT COMPOUND: LIQUID. FLUOROLUBE GR-544 JOINT COMPOUND: TAPE; TEFLON, 3 MIL. FEDERAL PROCESS CO. THRED TAPE FEL-PRO THREAD SEALING TAPE 3M BRAND #48 BAR STOCK BALL VALVE: 2000 PSI 100 DEG F;MALE THREADED BY FEMALE THREADED MONEL BODY; MONEL STEM; MONEL BALL; ULTRAFIL SEATING; ULTRAFIL STEM SEALS; ROUND OR OVAL HANDLE; PREPARED FOR CHLORINE SERVICE AT FACTORY; TBV 4161-SE-M4M4-UT GAUGE VALVE: CLASS 6000; NPTM BY NPTF (THREE MULTI PORT); ASTM B 164; MONEL ANNEALED BODY; SELF-ALIGNED BALL TYPE; UNION BONNET; MONEL K500'STEM; MONEL BALL; INTEGRAL SEATING; PTFE PACKING; ANSI B1.20.1. ANDERSON-GREENWOOD M5VHM-4 6 LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046803 f.'ONF T DFNT T Al PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM VIB1500M02 SIZE VIB2 OOOMOll VIB2 000MO12 VIB2 OOOM013 VIBlOOOMOl VIX6000M02 PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 19 OF 20 DESCRIPTION BAR STOCK BALL VALVE: 1500 PSI @ 175 DEG F;MALE THREADED BY FEMALE THREADED; MONEL BODY; MONEL KSOO'STEM; MONEL BALL PTFE SEATING; FUGITIVE EMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE; ORIFICE TAP. TBV FE-4161-SE-M4M4-TT BAR STOCK BALL VALVE: 2000 PSI g 100 DEG F,* MALE SOCKET WELDING BY FEMALE THREADED; MONEL BODY; MONEL K500'STEM; MONEL BALL; PTFE SEATING; FUGITIVE EMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE. TBV FE-4161-SWXSE-M4M4-TT BAR STOCK BALL VALVE : 2000 PSI g 100 DEG F; THREADED; MONEL BODY; PTFE SEATING; FUGITIVE EMMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE; TBV FE-41SE-M4M4-TT BAR STOCK BALL VALVE: 2000 PSI g 100 DEG F,*MALE THREADED BY FEMALE THREADED; MONEL BODY; MONEL KSOO'STEM; MONEL BALL PTFE SEATING; FUGITIVE EMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE. TBV FE-4161-SE-M4M4-TT BAR STOCK VALVE: 1000 PSI g 100 DEG F; MALE SOCKET WELDING INLET PORT; BY 1/2 IN NPTF (THREE MULTI PORT); MONEL BODY; MONEL KSOO'STEM; MONEL BALL; PTFE SEATING; PTFE STEM SEALS; ROUND OR OVAL HANDWHEEL. TBV 61-SW/SE-M4-M4-TT-L TRANSMITTER MANIFOLD ASSEMBLY: 6000 PSI g 200 DEG F; FLANGED; K MONEL; PTFE' PACKING. VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE. ANDERSON-GREENWOOD M4AVM LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 00 A 046804 CONFTDFNTT Al PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION ITEM NOTE <n> SIZE NOTE PIPING SPEC CODE: L103 DATE: 02-11-94 PAGE: 20 OF 20 DESCRIPTION CONTROL AND AUTOMATED VALVES: CONTROL AND AUTOMATED VALVES SHALL BE OF THE FOLLOWING SPECIFICATIONS: CONTROL VALVES: TYPE: AS DETERMINED BY APPLICATION BODY: CAST 300 SERIES STAINLESS STEEL TRIM: HASTELLOY C PACKING: LIVE LOADED TEFLON SEALS/GASKETS: HASTELLOY C BELLOW SEAL FLANGE BOLTING: ALLOY 20 (CLEANED AND PACKAGED FOR CL2 SERVICE) IF FISHER V500 VBALL VALVE IS USED, THE FOLLOWING MATERIALS ARE ACCEPTABLE TYPE: FISHER V500 BODY: CAST 300 SERIES STAINLESS STEEL BALL: CHROMIUM PLATED CF-8M (CAST 316) SHAFT: 17-4 PH SS IN THE H1025 OR SOFTER CONDITION SEAT/RING: 316 SSTL W/STELLITE 6 SEAT PACKING: LIVE LOADED TEFLON FLANGE BOLTS: ALLOY 20 (CLEANED AND PACKAGED FOR CL2 SERVICE) AUTOMATED (ON/OFF) VALVES: TYPE AND SIZE ARE DETERMINED BY APPLICATION AND SHOULD BE SELECTED FROM THE VALVE SECTION OF THIS SPECIFICATION. THE VALVE SHOULD BE AUTOMATED IN ACCORDANCE WITH ENGINEERING PRACTICE L6C-8400. LAST UPDATE: 10-15-93 NPL8087 PIPING SPEC CODE: L103 DO A 046805 CONFTDFNTT Al