Document DMo45412Z5Eddxvx9vbprZqLn

.1 40 CFR Ch. I (7-1-93 Edition) | maxi- (iii) If subject to 61.139(f)(2)(iiil. Tiina- records of the conditions found during never each monthly inspection, and of each period when the car seal is broken, , the when the valve position is changed, or 31113? when maintenance on the bypass line date valve is performed. irbon (j) The following reporting require f the ments are applicable to owners or oper .nrl a ators of control devices subject to e ac- 61.139: >r at (1) Compliance test3 shall be reported ;nces as specified in 161.13(f). -.pent (2) The following information shall :d In be reported on a quarterly basis. Two rded of the quarterly reports shall be sub mitted as part of the semiannual re the ports required in 561.138(f). d In (i) For each carbon adsorber: is of .eter nost ded. (A) The date and time of detection of each exceedance of the maximum con centration point and a brief description of the time and nature of the correc Tec- tive action taken. i for (B) The date of each time that the tion captured benzene or removed carbon xies was not handled as required in 61.139 per- (b)(1) and (2), and a brief description of the corrective action taken. ther (C) The date of each determination of ver- the maximum concentration point, as iore described m 561.139(h). and a brief rea om- son for the determination. :ost (ii) For each vapor incinerator, the date and duration of each exceedance tor, of the boundary parameters recorded ent under 61.139(i)(6) and a brief descrip ;ta- tion of the corrective action taken. low (iii) For each vapor incinerator, the ent date and duration of each period speci oer- fied as follows: ra (A) Each period recorded under ted 61.139(i)(")(I) when the vent stream is lge diverted from the control device or has .ta- no flow rate: er- (B) Each period recorded under 61.139(l)(7)(ii) when the vent stream is the diverted from the control device: and ist (C) Each period recorded under 5 61.139(1)(7)(iii) when the vent stream is -ds diverted from the control device, when fl the car seal is broken, when the valve ed is unlocked, or when the valve position no has changed. (iv) For each vapor incinerator, the i). owner or operator shall specify the of method of monitoring chosen under li- 561.139(f)(2) in the first quarterly re port. Any time the owner or operator 72 ronmental Protection Agency 61.141 change^that choice, he shall specify Tie change, in the first quarterly report 'ollowing the change. ' (3) If. for a'given quarter in which no friable asbestos waste material, and bags or other similar- packaging con taminated with commercial asbestos. As applied to demolition and renova semiannual resort is due under tion operations, this term also Includes 161138(f). there is so information to re regulated asbestos-containing material port under 61.139(j)tt)(i)(A). (j)(2)(i)(B). waste and materials contaminated tj)(2)(ii)(A). and (j)(2)Ki)(B). then the with asbestos including disposable owner or operator may ss^bmit a state ment to that effect alongNrith the in formation to be reported under 561.139(j)(2)(i)(C) in the nexbv semi annual report, rather than submitting a report at the end of the quarter, ra <7df)7 6npr ia laaij.. equipment and clothing. Asbestos mill means any facility en gaged in converting, or In any inter mediate step in converting, asbestos ore into commercial asbestos. Outside storage of asbestos material is not con sidered a part of the asbestos mill. Asbestos tailings means any solid Subpart M--National Emission Standard for Asbestos waste that contains asbestos and is a product of asbestos mining or milling operations. Asbestos waste from control devices AfTHORrrr: 42 U.S.C. 7401. 7412, 7414. 7416. means any waste material that con 7601. tains asbestos and is collected by a pol SOVKCE: 49 FR 13661, Apr. S. 1984, unless lution control device. otherwise noted. Category l nonfriable asbestos-contain } 61.140 Applicability. The provisions of this subpart are ap plicable to those sources specified in 61.142 through 61.151. 61.154, and 61.155. ing material (ACM) means asbestos-con taining packings, gaskets, resilient floor covering, and asphalt roofing products containing more than 1 per cent asbestos as determined using the (65 FR 48414. Nov. 20. 19901 method specified in appendix A. sub part F. 40 CFR part 763, section 1, Po 61.141 Definitions. larized Light Microscopy. All terms that are used In this sub part and are not defined below are given the same meaning as in the Act and in subpart A of thi3 part. Active waste disposal site means any disposal site other than an inactive site. Adequately wet means sufficiently mix or penetrate with liquid to prevent the release of particulates. If visible emissions are observed coming from as bestos-containing material, then that material has not been adequately wet ted. However, the absence of visible emissions is not sufficient evidence of being adequately wet. Asbestos means the asbestiform vari eties of serpentinite (chrysotile), rie- beckite (crocidolite). cummingtonitefrunerite, anthophyllite, and actino- nte-tremolite. Asbestos-containing waste materials means mill tailings or any waste that contains commercial asbestos and is generated by a source subject to the Provisions of this subpart. This term includes filters from control devices. Category II nonfnable ACM means any material, excluding Category I nonfri able ACM. containing more than 1 per cent asbestos as determined using the methods specified in appendix A. sub part F. 40 CFR part 763, section 1. Po larized Light Microscopy that, when dry. cannot be crumbled, pulverized, or reduced to powder by hand pressure. Commercial asbestos means any mate rial containing asbestos that is ex tracted from ore and has value because of its asbestos content. Cutting means to penetrate with a sharp-edged instrument and includes sawing, but does not include shearing, slicing, or punching. Demolition means the wrecking or taking out of any load-supporting structural member of a facility to gether with any related handling oper ations or the intentional burning of any facility. Emergency renovation operation means a renovation operation that was not planned hut results from a sudden, un expected event that, if not inune- 73 1 61.141 40 CFR Ch. I (7-1-93 Editk diately attended to. presents a safety or public health hazard, is necessary to protect equipment from damage, or i3 necessary to avoid imposing an unrea sonable financial burden. This term in cludes operations necessitated by nonroutine failures of equipment. Fabricating means any processing (e.g., cutting, sawing, drilling) of a manufactured product that contains commercial asbestos, with the excep tion of processing at temporary sites (field fabricating) for the construction or restoration of facilities. In the case of friction products, fabricating in cludes bonding, debonding, grinding, sawing, drilling, or other similar oper ations performed as part of fabricating. Facility means any institutional, commercial, public, industrial, or resi dential structure, installation, or building (including any structure, in stallation. or building containing con dominiums or individual dwelling units operated as a residential cooperative, but excluding residential buildings having four or fewer dwelling units): any ship; and any active or inactive waste disposal site. For purposes of this definition, any building, structure, or installation that contains a loft used as a dwelling is not considered a residential structure, installation, or building. Any structure, installation or building that was previously subject to this subpart is not excluded, regardless of its current use or function. Facility component means any part of a facility including equipment. Friable asbestos material means any material containing more than 1 per cent asbestos as determined using the method specified in appendix A. sub part F. 40 CFR part 763 section 1, Polar ized Light Microscopy, that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure. If the as bestos content is less than 10 percent as determined by a method other than point counting by polarized light mi croscopy (PLM), verify the asbestos content by point counting using PLM. Fugitive source means any source of emissions not controlled by an air pol lution control device. Glove bag means a sealed compart ment with attached inner gloves used for the handling of asbestos-containing materials. Properly installed and used. glove bags provide a small work a enclosure typically used for small-sc asbestos stripping operations. Inforr. tion on glove-bag installation, equ meat and supplies, and work practf. is contained in the Occupational Saf< and Health Administration's (OSHA final rule on occupational exposure asbestos (appendix G to 29 CFR 1926.; Grinding means to reduce to powc or small fragments and includes n chanical chipping or drilling. In poor condition, means the binding the material is losing its integrity indicated by peeling, cracking, crumbling of the material. Inactive waste disposal site means a disposal site or portion of it where z ditional asbestos-containing waste ir terial has not been deposited with the past year. Installation means any building structure or any group of buildings structures at a single demolition renovation site that are under the co trol of the same owner or operator ( owner or operator under common co trol). Leak-tight means that solids or Ji uids cannot escape or spill out. It al. means dust-tight. Malfunction means any sudden a: unavoidable failure of air pollutic control equipment or process equf ment or of a process to operate in normal or usual manner so that enu sions of asbestos are increased. Fa ures of equipment shall not be consi ered malfunctions if they are caused any way by poor maintenance, carele operation, or any other preventab upset conditions, equipment breai. down, or process failure. Manufacturing means the combinic of commercial asbestos--or. in the cas of woven friction products, the combit ing of textiles containing commercia asbestos--with any other maceriaKs including commercial asbestos, and th processing of this combination into . product. Chlorine production is consid ered a part of manufacturing. Natural barrier means a natural ob ject that effectively precludes or deter access. Natural barriers include phy* ical obstacles such as cliffs, lakes o: other large bodies of water, deep anc wide ravines, and mountains. Remote ness by itself is not a natural barrier. 74 ASARCOELP 0000432 * Jfcjp. ^T ivironmontal Protection Agency ! 61.142 Sonfnable asbestos-containing material e&ns any material containing more an 1 percent asbestos as determined iing the method specified in appendix subpart F. 40 CFR part 763. section X. olarized Light Microscopy, that, when -v cannot be crumbled, pulverized, or Iduced to powder by hand pressure. Sonscheduled renovation operation eans a renovation operation necestated by the routine failure of equip ment. which is expected to occur witha a given period based on past operatag experience, but for which an exact ate cannot be predicted. Outside air means the air outside (hidings and structures, including, but ,ot limited to. the air under a bridge r In an open air ferry dock. Owner or operator of a demolition or novation activity means any person ?ho owns, leases, operates, controls, or upervtses the facility being demolshed or renovated or any person who >wns, leases, operates, controls, or su pervises the demolition or renovation iperation. or both. Particulate asbestos material means Inely divided particles of asbestos or naterial containing asbestos. Planned renovation operations means a renovation operation, or a number of mch operations, in which some RACM will be removed or stripped within a nven period of time and that can be predicted. Individual nonscheduled op erations are included if a number of juch operations can be predicted to pccur during a given period of time based on operating experience. Regulated asbestos-containing material 'RACM) means (a) Friable asbestos ma terial, (b> Category I nonfriable ACM that has become friable, (c) Category I aonfrtable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading, or (d) Category II nonfriable ACM that has a high prob ability of becoming or has become crumbled, pulverized, or reduced to Powder by the forces expected to act on the material in the course of demoli tion or renovation operations regulated by this subpart. means co out RACM or acuity components that contain or are *ret* witl1 RACM from any facility. Renovation means altering a facility one or more facility components in any way. including the stripping or re moval of RACM from a facility compo nent, Operations in which load-sup porting structural members are wrecked or taken out are demolitions. Resilient floor covering means asbes tos-containing floor tile, including as phalt and vinyl floor tile, and sheet vinyl floor covering containing more than 1 percent asbestos as determined using polarized light microscopy ac cording to the method specified in ap pendix A. subpaxt F. 40 CFR part 763, Section 1. Polarized Light Microscopy. Roadways means surfaces on which vehicles travel. This term includes public and private highways, roads, streets, parking areas, and driveways. Strip means to take off RACM from any part of a facility or facility compo nents. Structural member means any loadsupporting member of a facility, such as beams and load supporting walls: or any nonload-supporting member, such as ceilings and nonload-supporting walls. Visible emissions means any emissions, which are visually detectable without the aid of instruments, coming from RACM or asbestos-containing waste material, or from any asbestos milling, manufacturing, or fabricating oper ation. This does not Include condensed, uncombined water vapor. Waste generator means any owner or operator of a source covered by this subpart whose act or process produces asbestos-containing waste material. Waste shipment record means the ship ping document, required to be origi nated and signed by the waste genera tor, used co crack and substantiate the disposition of asbestos-containing waste material. Working day means Monday through Friday and includes holidays that fall on any of the day3 Monday through Friday. t FR 13651, Apr. 5.1984; 49 FR 25453. June 21. 1984. as amended by 55 FR 48414, Nov. 20. 1990; SS FR 1669. Jan. 16.19911 5 61.142 Standard for asbestos mills. (a) Each owner or operator of an as bestos mill shall either discharge no visible emissions to Che outside air from that asbestos mill, including fugi tive sources, or use the methods speci- 75 I ASARCO ELP 0000433