Document 0LzODYOKZ1kK3Mj714NobBK7R
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
PIPING SPEC CODE: LI02 DATE: 02-11-94 PAGE: 1 OF 21
CHLORINE GAS ( DRY LESS THAN 20 PPM WATER )
CLASS 150 235. PSIG AT 275. DEG. F TO -20. DEG. F TEST CLASS & PRESS: C @ 353 MATERIAL: CARBON STEEL CORROSION ALLOWANCE: .0625 INCHES INDUSTRY PIPING CODE: ASME B31.3-1990 EDITION
ITEM
SIZE
DESCRIPTION
NOTES
NOTE <n>
PRESSURE AND TEMPERATURE LIMITING FACTORS ARE LARGE BRANCH CONNECTIONS AT 235 PSIG.
NOTE <n>
THIS PIPING SPEC CONFORMS TO PIPING CODE ASME B31.3, NORMAL SERVICE, IN REGARDS TO INTERNAL PRESSURE AND TEMPERATURES STATED ABOVE IN HEADER DESCRIPTION. CHECK COMPLETED ON 08/12/92. ADDITIONAL APPLICABLE CODE EVALUATIONS SHOULD BE PERFORMED AT THE PROJECT LEVEL FOR CONDITIONS SUCH AS EQUIPMENT NOZZLE LOADINGS, STRESSES DUE TO THERMAL EXPANSIONS, WEIGHT, LIQUID EXPANSION, ETC.
NOTE <n>
CAUTION
TITANIUM REACTS CATASTROPHICALLY WITH DRY CHLORINE. DO NOT USE TITANIUM METAL COMPONENTS IN THIS SERVICE.
N737
CAUTION
PIPING ON THIS SPECIFICATION SHALL BE ALL WELDED AND/OR FLANGED INCLUDING THE FIRST BLOCK VALVE OFF THE LINE IN INSTRUMENT PIPING AND ALL VENT AND DRAIN VALVES.
NOTE <n>
INSPECTION
10% OF ALL CIRCUMFERENTIAL BUTT AND MITER GROOVE WELDS SHALL BE RANDOM RADIOGRAPHED. ACCEPTANCE SHALL BE IN ACCORDANCE WITH SEVERE CYCLIC CONDITIONS CRITERIA
NOTE <n>
INSPECTION
5% OF ALL SOCKET WELDS SHALL BE SPOT RADIOGRAPHED TO VERIFY CORRECT SOCKET GAP AND WELD QUALITY
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
r A COM? 46>6,5
TlAl
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE INSPECTION
NOTE <n>
WELDING
NOTE <n>
WELDING
NOTE <n>
NOTE <n>
N93J
NOTE <n> N93A
N238
CLEANING CLEANING CLEANING
CAUTION
N245
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 2 OF 21
DESCRIPTION
VISUAL INSPECTION IS REQUIRED IN ACCORDANCE WITH CODE CRITERIA FOR 'NORMAL'CATEGORY SERVICE.
WELDING AND FABRICATION SHALL BE IN ACCORDANCE WITH DOW SPECIFICATION L8S-6500-01.
APPLICABLE DOW WELDING PROCEDURES: SHOP FABRICATION - L8S-6501-AZ, L8S-6501-BQ AND L8S-6501-AP; FIELD FABRICATION L8S-6501-BQ, L8S-6501-DV AND L8S-6501-CB.
PIPING SHALL BE INSTALLED IN ACCORDANCE WITH ENGINEERING SPECIFICATION L4S-4210-01 AND TESTED PER ENGINEERING SPECIFICATION L4S-6410-01.
FLANGE BOLTING SHALL BE INSTALLED IN ACCORDANCE WITH DOW ENGINEERING SPECIFICATION L5C-3800-00, BOLT TORQUE TABLE #2.
ALL PIPING TO BE DEGREASED PRIOR TO ASSEMBLY.
FOR SPECIFIC CLEANING INSTRUCTIONS, PLEASE REFER TO PROJECT SPECIFICATIONS.
ALL VALVES SHALL BE DEGREASED, SEALED AND TAGGED AT FACTORY FOR CHLORINE SERVICE.
CAUTION: CHLORINE LINES SHALL BE PLACED IN THE PIPEWAYS SO THAT NO LINES CARRYING CORROSIVE MATERIALS SHALL PASS OVER THEM.
SEE ENGINEERING SPECIFICATION N4S-9803-01 FOR ACCEPTABLE MANUFACTURERS OF PIPE AND PIPING ,COMPONENTS.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046766 CONF T dfnttai
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE DESIGN
NOTE <n>
N84 0
NOTE <n> PIPE P28B P3BW
NOTE <n> PIPE NIPPLES PN28BSW
PN28BSWXL
1/2 - 1 1/2 2-20
1/2 - 1 1/2 1/2 - 1 1/2
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 3 OF 21
DESCRIPTION
WHEN SELECTING BALL VALVES, USE STANDARD PORT VALVES UNLESS PRESSURE DROP CONSIDERATIONS JUSTIFY THE USE OF FULL PORT VALVES.
PROVIDE WELDED PIPE SHOES FOR ALL BUTT WELDED PIPING AT PIPE SUPPORTS. WEAR PLATES ARE PROHIBITED. AVOID THE USE OF BOLTED SHOES, CLEVIS, AND U-BOLT TYPE SUPPORTS. SEAL WELDED PLATE LUGS ARE PREFERRED FOR ATTACHMENT OF PIPE HANGERS TO PIPE
MACHINE FLARED LAP (VANSTONE) JOINTS ARE NOT PERMITTED ON THIS PIPING SPECIFICATION.
DO NOT ROUTE PIPE SIZES SMALLER THAN 2" IN PIPE RACKS.
PIPE: EXTRA STRONG; SEAMLESS; ASTM A 106 GR B; CARBON STEEL.
PIPE: STANDARD WEIGHT; ERW; ASTM A 53 TYPE E GR B OR API 5L GR B; CARBON STEEL.
P27B IS AN ACCEPTABLE SUBSTITUTE FOR P3BW.
PIPE NIPPLE: EXTRA STRONG; SEAMLESS; ASTM A 106 GR B; CARBON STEEL; 3 IN LONG; PLAIN ENDS.
PIPE NIPPLE: EXTRA STRONG; SEAMLESS; ASTM A 106 GR B; CARBON STEEL; 6 IN LONG; PLAIN ENDS.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
r,P a 04t>767
CON'
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
SIZE
BRANCH CONNECTIONS
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 4 OF 21
DESCRIPTION
BC1
HEADER SIZE
NINETY DEGREE BRANCHES SHALL BE DESIGNED AND INSTALLED IN ACCORDANCE WITH THE FOLLOWING TABULATION:
BRANCH SIZE
BRANCH SAME AS HEADER OR SMALLER
CONNECTION
NOTE <n>
FITTINGS E64 L64 T64 TR64 PC2 7
- 1 1/2 - 1 1/2
20 20 20
1/2 - 1 1/2 1/2 - 1 1/4
2 - 20 1/2 - 1 1/2 2 - 18
SAME SMALLER
SAME SMALLER SMALLER
TEE RED.TEE OR TEE & SWAGE TEE SOCKOLET PLAIN STUB-IN
1/2 - 1 1/2 1/2 - 1 1/2 1/2 - 1 1/2 1/2 - 1 1/2 1/2 - 1 1/2
ELBOW 90 DEG: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll.
ELBOW 45 DEG: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll.
TEE: SOCKET WELDING; CLASS 3000; FORGED ASTM A 105; CARBON STEEL; ASME B16.ll.
TEE REDUCING: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll.
CAP: SOCKET WELDING; CLASS 3000; FORGED ASTM A 105; CARBON STEEL; ASME B16.ll.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046768 f'.ONF T DFNT T Al
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM PC2
SIZE 1/2 - 1
RC22P
1/2 - 1 1/2
RE22P
1/2 - 1 1/2
RC22BP
1/2 - 2
RE22BP
1/2 - 2
C14C C14S
1/2 - 1 1/2 1/2 - 1 1/2
C42
1/2 - 1 1/2
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 5 OF 21
DESCRIPTION
PLUG HEX HEAD; THREADED; FORGED; ASTM A 105; SOLID CARBON STEEL; ASME B16.ll AND ANSI Bl.20.1.
SWAGED NIPPLE CONCENTRIC: PLAIN BOTH ENDS; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL.
SWAGED NIPPLE ECCENTRIC: PLAIN BOTH ENDS; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL.
SWAGED NIPPLE CONCENTRIC: BEVELED LARGE END, PLAIN SMALL END; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL.
SWAGED NIPPLE ECCENTRIC: BEVELED LARGE END, PLAIN SMALL END; EXTRA STRONG; SEAMLESS; ASTM A 106 GR B OR ASTM A 696 GR B OR ASTM A 696 GR C; CARBON STEEL.
COUPLING: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll.
STRAIGHT TYPE O-LET BRANCH: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL. ASME B16.ll. ANVIL (CANVIL) ANVILET BONNEY FORGE SOCKOLET WFI INTERNATIONAL, INC. SOCKET WELD PIP PENNSYLVANIA MACHINE WORKS SOCKET WELD PHOENIX SOCKET WELD TRANS-O-CON
STRAIGHT TYPE O-LET BRANCH: BEVELED ENDS; EXTRA STRONG; FORGED; ASTM A 105; CARBON STEEL; ASME B16.9. ANVIL (CANVIL) BUTT WELD ANVILET BONNEY FORGE WELDOLET PENNSYLVANIA MACHINE WORKS BUTT WELD OU PHOENIX TRANS-O-CON BUTT WELD CONNECTIO WFI INTERNATIONAL, INC. BUTT WELD PIPET
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046769 OONFTOFNTT A1
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM C3ESW
SIZE 1/2 - 1 1/2
C54SW
1/2 - 1 1/2
C54SWXL
1/2 - 1 1/2
C41E
2-4
C41
2-20
E15B
2-20
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 6 OF 21
DESCRIPTION
ELBOW TYPE O-LET BRANCH: SOCKET WELDING; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll. ANVIL (CANVIL) ELBOW ANVILET BONNEY FORGE ELBOLET PENNSYLVANIA MACHINE WORKS ELBO OUTLET PHOENIX TRANS-O-CON ELBOW CONNECTION WFI INTERNATIONAL, INC. ELBO PIPET
NIPPLE TYPE O-LET BRANCH: PLAIN END; EXTRA STRONG; FORGED; ASTM A 105; CARBON STEEL; 3 1/2 INCH LONG. BONNEY FORGE NIPOLET PENNSYLVANIA- MACHINE WORKS NIPPLE OUTLE WFI INTERNATIONAL, INC. NIPPLE PIPET
NIPPLE TYPE O-LET BRANCH: PLAIN END; EXTRA STRONG; FORGED; ASTM A 105; CARBON STEEL; 6 1/2 INCH LONG. BONNEY FORGE NIPOLET PENNSYLVANIA MACHINE WORKS NIPPLE OUTLE WFI INTERNATIONAL, INC. NIPPLE PIPET
ELBOW TYPE O-LET BRANCH: BUTT WELDING; STANDARD WEIGHT; FORGED; ASTM A 105; CARBON STEEL; ASME B16.9. ANVIL (CANVIL) ELBOW ANVILET BONNEY FORGE ELBOLET PENNSYLVANIA MACHINE WORKS ELBO OUTLET WFI INTERNATIONAL, INC. ELBO PIPET
STRAIGHT TYPE O-LET BRANCH: BUTT WELDING; STANDARD WEIGHT; FORGED; ASTM A 105; CARBON STEEL; ASME B16.9. ANVIL (CANVIL) BUTT WELD ANVILET BONNEY FORGE WELDOLET PENNSYLVANIA MACHINE WORKS BUTT WELD OU PHOENIX TRANS-O-CON BUTT WELD CONNECTIO WFI INTERNATIONAL, INC. BUTT WELD PIPET
ELBOW 90 DEG LR: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
oo A 046770 ("ONF T DF-'NT T AI
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM L15B
SIZE 2-20
T15B
2-20
TR15B
2-20
RC15B
2-20
RE15B
2-20
X15B
2-20
PC51B
2-20
FLANGES F14RF80
1/2 - 1 1/2
F24RFSTD
2-20
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 7 OF 21
DESCRIPTION
ELBOW 45 DEG: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
TEE: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
TEE REDUCING: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
REDUCER CONCENTRIC: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
REDUCER ECCENTRIC: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
CROSS: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
CAP: BUTT WELDING; STANDARD WEIGHT; SEAMLESS; ASTM A 234 GR WPB; CARBON STEEL; ASME B16.9.
FLANGE: SOCKET WELDING; CLASS 150; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5 * BORE TO MATCH SCHEDULE 80. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
FLANGE: WELDING NECK; CLASS 150; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5. BORE TO MATCH STANDARD WEIGHT. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
00 A 04A771 OONFTDFNT1A1
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM F3RF
SIZE 1/2 - 20
GASKETS G39D
FASTENERS BA193B7QC
BA19 3B7QCSC
BOLT LUBRICANT BL10
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 8 OF 21
DESCRIPTION
FLANGE: BLIND; CLASS 150; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
GASKET: FLAT RING; FILLED PTFE; BARIUM SULFATE FILLER; 1/16 INCH THICK; GARLOCK GYLON STYLE 3510 (OFF-WHITE)
COATED STUD BOLT: ASTM A 193 GR B7; LIQUID QUENCHED AND TEMPERED; ALLOY STEEL; WITH ASTM A 194 GR 2H HEAVY HEX NUTS. STUD BOLTS AND NUTS TO BE FLUOROPOLYMER COATED, COLOR TO BE BLUE. FLUOROPOLYMER COATING TO BE AS SUPPLIED BY STANCO BOLT DIVISION, METALS COATING CORP., PROTECTIVE COATINGS INC., OR INDUSTRIAL METAL FINISHING CO.
COATED CAP SCREW: ASTM A 193 GR B7; LIQUID QUENCHED AND TEMPERED; ALLOY STEEL. CAP SCREWS TO BE FLUOROPOLYMER COATED, COLOR TO BE BLUE. FLUOROPOLUMER COATING TO BE AS SUPPLIED BY STANCO BOLT DIVISION, METALS COATING CORP., PROTECTIVE COATINGS INC., OR INDUSTRIAL METAL FINISHING CO.
BOLT LUBRICANT: PASTE, NICKEL BASED, ANTISEIZE COMPOUND. FEL PRO NICKEL EASE FEDERAL PROCESS CO. THRED-GARD NICKEL NEVER SEEZ NICKEL SPECIAL
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
C0O0NFAIDENTIAL
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE
VALVES
VG150CS1E3RF
2-20
PIPING SPEC CODE: LI02 DATE: 02-11-94 PAGE: 9 OF 21
DESCRIPTION
BOLT LUBRICANT IS REQUIRED ONLY WHEN FLUOROPOLYMER COATING IS DAMAGED, OR WHEN REUSING EXISTING NON-COATED BOLTS.
GATE VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; OS&Y, RISING STEM, FULL PORT TYPE; BOLTED BONNET; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; SOFT IRON GASKET; FLEXIBLE WEDGE DISC; HASTELLOY C TRIM; PTFE CHEVRON PACKING; WEATHERPROOF GEAR OPERATOR; API 600; ASME B16.5/B16.47 SERIES A; PREPARED FOR CHLORINE SERVICE AT FACTORY; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. KITZ 150SCL NEWCO 11F-CB9 RAIMONDI 3005 VELAN F-0064C
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
00 ^ 046773 conftofnt TA!
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VGL150LC5ARF
SIZE 1 1/2 - 12
VC150FS3RF
1/2 - 2
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 10 OF 21
DESCRIPTION
GLOBE VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 352 GR LCC; CAST LOW TEMPERATURE CARBON STEEL BODY; BELLOWS TYPE; BOLTED BONNET; ASTM A 320 GR L7 LIQUID QUENCHED & TEMPERED BOLTING; PTFE GASKET; HASTELLOY C STEM; HARD FACED LOW TEMPERATURE CARBON STEEL DISC; HARD FACED SEATING; BELLOWS, FORMED MULTI-LAYER HASTELLOY C; BELLOWS HOLDER, HASTELLOY C; PTFE PACKING; ASME B16.5; POSITION INDICATOR; FOR LOW EMISSION SERVICE AND PREPARED FOR CHLORINE SERVICE AT FACTORY; FOR CRYOGENIC SERVICE; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. ALL MATERIALS OF CONSTRUCTION TO BE SUITABLE FOR SERVICE TO -50 DEG F. DESCOTE 2102B/150/GVF/25.1
CHECK VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 105; FORGED CARBON STEEL BODY; PISTON, HORIZONTAL TYPE; BOLTED COVER; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; FLEXIBLE GRAPHITE GASKET; HARD FACED SEATING; 13% CHROME ALLOY STEEL TRIM; ASME B16.5 PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. VELAN F-0034B-02TY VOGT 573
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 04A774 CONF TDFNTTA!
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VC150CS1RF
SIZE 2-20
VB150CS48ARF
1/2 - 4
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 11 OF 21
DESCRIPTION
CHECK VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; SWING TYPE; BOLTED COVER; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; SOFT IRON GASKET; HARD FACED SEATING; 13% CHROME ALLOY STEEL TRIM; ASME B16.5 PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. KITZ 150SC0B NEWCO 31F-CB2 RAIMONDI 3026 VELAN 00114C-02TY
BALL VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; ALLOY 20 STEM; ALLOY 20 BALL; PTFE SEATING; PTFE STEM SEALS OR PACKING; 1 INCH AND UNDER SHALL HAVE ROUND OR OVAL HANDWHEEL; 1 1/4 INCH THRU 4 INCH SHALL HAVE LEVER OPERATOR. WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY" HANDLE FOR INSULATED SERVICE"; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. MCCANNA N151 JAMESBURY 5150 KITZ 150SCTA NIBCO 510 TBV 1200 VELAN F-00402 WORCESTER 51V19 HOLLOW BALL NOT ACCEPTA WATTS 1500
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 040775 OONR-TDFNITTA!
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VB150CS8BRF
SIZE 6-10
NOTE <n>
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 12 OF 21
DESCRIPTION
BALL VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 216 GR WCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; ALLOY 20 STEM; ALLOY 20 BALL; PTFE SEATING; PTFE STEM SEALS OR PACKING; WEATHERPROOF GEAR OPERATOR. THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO'250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. MCCANNA N151 JAMESBURY 5150 KITZ 150 SCTA KTM E0800 NIBCO 510 TBV 1200 VELAN F-00402 WATTS 1500 WKM 310C-RB100 WORCESTER 51 VI9 HOLLOW BALL NOT ACCEPT
VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
046.776 DO CONFIDENTIAL
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VB150CS7OARF
SIZE 1/2 - 4
VB150CS7 OBRF
6-10
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 13 OF 21
DESCRIPTION
VENTED BALL VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 352 GR LCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; HASTELLOY C STEM; HASTELLOY C BALL; PRESSURE RELIEVING REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; 1 INCH AND UNDER SHALL HAVE ROUND OR OVAL HANDWHEEL; 1 1/4 INCH THRU 4 INCH SHALL HAVE LEVER OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; WHEN REQUIRED FOR INSULATED SERVICE, REQUISITIONER TO SPECIFY "HANDLE FOR INSULATED SERVICE"; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 515OC NIBCO 510 TBV CL 1200
VENTED BALL VALVE: CLASS 150; RAISED FACE; FLANGED; ASTM A 352 GR LCB; CAST CARBON STEEL BODY; REDUCED PORT TYPE; ASTM A 193 GR B7 LIQ. QUENCHED & TEMPERED BOLTING; PTFE BODY SEAL; HASTELLOY C STEM; HASTELLOY C BALL; PRESSURE RELIEVING REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; WEATHERPROOF GEAR OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; THE FINISH OF THE GASKET CONTACT FACES OF END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. JAMESBURY 5150C NIBCO 510 TBV CL 1200
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VBF150CS7CWT
SIZE 3-6
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 14 OF 21
DESCRIPTION
BUTTERFLY VALVE: CLASS 150; RAISED FACE TAPPED LUG; ASTM A 216 GR WCB;CARBON STEEL BODY; ALLOY 20 (UNS NOS020) BOLTING; MONEL K500 STEM; DISC MONEL; REINFORCED PTFE SEATING;; PTFE STEM SEALS OR PACKING; BOLTED PACKING GLAND; ASME B16.5; THROTTLING LOCKING LEVER OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY. [CAUTION: ASTM A 515 GR 70 IS NOT AN ACCEPTABLE MATERIAL] THE FINISH OF THE GASKET CONTACT FACES OF THE END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5. THIS VALVE SHALL NOT BE USED FOR DEAD END SERVICE. SIDE OF VALVE.) DEZURIK BHP,LI,CS,TC,ML-ML-FT-TT,UR*LT
FLOWSEAL 1LA-133RTG-LC JAMESBURY 815LC-EXXX-2271MT KEYSTONE K-LOK 362-162-BB-CHLORINE XOMOX 811-2-3-3-ST2-L-C-X
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046778 CONF7DFNTIAI.
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 15 OF 21
ITEM
SIZE
DESCRIPTION
VBF150CS7DWT
8-20
BUTTERFLY VALVE: CLASS 150; RAISED FACE; TAPPED LUG; ASTM A 216 GR WCB; CARBON STEEL BODY; ALLOY 20 (UNS NOS020) BOLTING; MONEL K500 STEM; DISC MONEL; REINFORCED PTFE SEATING; PTFE STEM SEALS OR PACKING; BOLTED PACKING GLAND; ASME B16.5/B16.47 SERIES A; WEATHERPROOF GEAR OPERATOR; PREPARED FOR CHLORINE SERVICE AT FACTORY; CLEANED & PACKAGED IN ACCORDANCE WITH N4S-9914-01; [CAUTION: ASTM A 515 GR 70 IS NOT AN ACCEPTABLE MATERIAL] THE FINISH OF THE GASKET CONTACT FACES OF THE END FLANGES SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5; 8-THREAD SERIES BOLTS ARE REQUIRED WHEN THE FLANGE BOLT DIAMETER IS 1 1/8 INCH OR LARGER; THIS VALVE SHALL NOT BE USED FOR DEAD END SERVICE. THIS VALVE SHOULD BE INSTALLED WITH THE SEAT AND SEAT RETAINER RING ON THE UPSTREAM (HIGH PRESSURE) SIDE OF VALVE.) DEZURIK BHP,LI,CS,TC,ML-ML-FT-TT,UR*HD
FLOWSEAL 1LA-133RTG-3C JAMESBURY 815LC-11-2271MT/MAO KEYSTONE K-LOK 362-162-AB-G-CHLORINE XOMOX 811-2-3-3-ST2-G-C-X
********************************************************************************
INSTRUMENTATION
NOTES
N101
THE FOLLOWING SPECIFICATIONS ARE TO BE USED FOR INSTRUMENTATION. FOR ITEMS NOT LISTED, THE PRECEDING PIPING SPECIFICATION IS TO BE USED WHERE APPLICABLE.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046779
confidential
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 16 OF 21
ITEM
SIZE
DESCRIPTION
N7033
INSTRUMENT PIPING IS DEFINED AS THAT PIPING FROM THE FIRST BLOCK VALVE OFF THE PROCESS LINE (NOT INCLUDING THE VALVE) TO THE INSTRUMENT.
N7 022
ALL SMALL INSTRUMENT CONNECTIONS SHALL BE IN AN EASILY ACCESSIBLE LOCATION.
N7003
FLOW (ORIFICE) TAPS:
NOTE <n>
ORIFICE TAPS ON VAPOR LINES SHALL BE MOUNTED ON THE TOP.
N7302
1/2 IN. SW
TAPS TO ORIFICE FLANGES SHALL BE 1/2" SOCKET WELD.
NOTE <n>
ORIFICE PLATES SHALL BE HASTELLOY C OR MONEL CONSTRUCTION, AND MEET OR EXCEED ANSI/API 2530 (A. G. A. REPORT # 3) FOR SHAPE, FINISH, BEVELING AND THICKNESS.
N7004
PRESSURE TAPS:
NOTE <n>
1 1/2 IN. RFF.
TAP ORIENTATION SHALL BE VERTICAL, TOP OF HORIZONTAL LINE, FOR GAS SERVICE, AND SIDE OF PIPE FOR HORIZONTAL LINES IN LIQUID SERVICE.
NOTE <n>
TAPS SHALL BE LINE SIZE ON PIPE SMALLER THAN 11/2 INCH.
N7005
TEMPERATURE TAPS:
N7460
THERMOWELLS SHALL HAVE A MINIMUM 0.26 INCH I.D.
N7402 <n>
1-1/2" SW/RFF
TAP ORIENTATION FOR THERMOWELLS SHALL BE SUCH THAT THE INSERTED WELL FACES AGAINST OR IS PERPENDICULAR TO THE DIRECTION OF FLUID FLOW. THERMOWELLS SHALL BE OF HASTELLOY C CONSTRUCTION.
N7007
OTHER TAPS:
NOTE <n>
1-1/2 IN. RFF
ANALYZER TAP ORIENTATION SHALL BE VERTICAL, TOP OF HORIZONTAL LINE.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046780 OONFTDFNTTAl
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE
N7 025 TUBING
PT105
1/4 - 1/2
PIPE NIPPLES PN8
1/2 - 1/2
PN8A
1/2 - 1/2
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 17 OF 21
DESCRIPTION
ALL PROCESS WETTED INSTRUMENTATION COMPONENTS SHALL BE OF THE FOLLOWING CONSTRUCTION:
BODY HALVES OR CASES: HASTELLOY C SENSOR ELEMENTS: HASTELLOY C DIAPHRAGMS: TANTALUM GASKETS: REINFORCED TEFLON O-RINGS AND SEALS: REINFORCED TEFLON SENSOR FILL FLUID: FLUOROLUBE
INSTRUMENTS NOT CLOSE COUPLED TO THE PROCESS SHALL BE CONNECTED BY TUBING. IF PIPE IS USED IT SHALL BE 1/2".
TUBING: 0.035 IN WALL; ANNEALED; SEAMLESS; ASTM B 165 (UNS N04400); MONEL 400. HARDNESS NOT TO EXCEED HRB 75, TUBING TO BE SUITABLE FOR BENDING AND FLARING, FREE OF SCRATCHES AND WITH AN EXTERIOR SURFACE THAT HAS A FINISH OF 32 MICROINCH RA. OR BETTER, MEASURED IN EITHER THE LONGITUDINAL OR CIRCUMFERENTIAL DIRECTION, AT ANY POINT ON THE TUBING. OUTSIDE DIAMETER TOLERANCE TO BE -0.0015 INCH AND+0.0045 INCH.
PIPE NIPPLE: BAR STOCK; 0.328 INCH I.D.; EXTRA STRONG WALL ASTM B 165; (UNSN04400); MONEL; 3 INCH LONG; THREADED ENDS. COLLINS INSTRUMENT CO. 133-0003-MON
PIPE NIPPLE: BAR STOCK; 0.328 INCH I.D.; EXTRA STRONG WALL ASTM B 165; (UNSN04400); MONEL; 6 INCH LONG; THREADED ENDS. COLLINS INSTRUMENT CO. 133-0006-MON
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM FITTINGS
SIZE
FT105C
1/4 - 1/2
N7021
N7001
CAUTION
E5
T5 FLANGES
F19RRF
1/4 - 1 1/4 - 1
JOINT COMPOUND JC18
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 18 OF 21
DESCRIPTION
TUBING FITTINGS: MONEL. HOKE GYROLOK
INTERCHANGING OF COMPRESSION FITTING PARTS OF DIFFERENT MANUFACTURES SHALL NOT BE ALLOWED.
WARNING!
CORRECT ASSEMBLY AND
INSTALLATION OF TUBE CONNECTIONS IS
CRITICAL! SWAGELOK TUBE CONNECTIONS
SHALL BE ASSEMBLED AND INSTALLED AS PER
SWAGELOK INSTALLATION INSTRUCTIONS.
WHEN ASSEMBLY AND INSTALLATION IS
COMPLETE, ALL SWAGELOK TUBE CONNECTIONS
SHALL BE CHECKED AND INSPECTED FOR
PROPER 'PULL-UP' WITH THE APPROPRIATE
SWAGELOK INSPECTION GAGE. TUBE
CONNECTIONS SHALL INCLUDE FITTINGS AND
VALVES.
ELBOW 90 DEG: THREADED; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll.
TEE: THREADED; CLASS 3000; FORGED; ASTM A 105; CARBON STEEL; ASME B16.ll.
FLANGE: REDUCING; THREADED; CLASS 150; RAISED FACE; ASTM A 105; CARBON STEEL; ASME B16.5. THE FINISH OF THE GASKET CONTACT FACE OF FLANGE SHALL HAVE A ROUGHNESS OF 125 TO 250 MICROINCH IN ACCORDANCE WITH THE LATEST EDITION OF ASME/ANSI B16.5.
JOINT COMPOUND: LIQUID. FLUOROLUBE GR-544
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 04678/ CONFIDENTIAL
PIPING MATERIAL SPECIFICATION
DOW CHEMICAL USA LOUISIANA DIVISION
ITEM JC15
SIZE
VALVES
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 19 OF 21
DESCRIPTION
JOINT COMPOUND: TAPE; TEFLON, 3 MIL. FEDERAL PROCESS CO. THRED TAPE FEL-PRO THREAD SEALING TAPE 3M BRAND #48
VIB1500M02 VIB2000M011 VIB2000M013 VIB2 000MO8 VIG6000M01
BAR STOCK BALL VALVE: 1500 PSI @ 175 DEG F;MALE THREADED BY FEMALE THREADED; MONEL BODY; MONEL K500'STEM; MONEL BALL; PTFE SEATING; FUGITIVE EMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE; ORIFICE TAP. TBV FE-4161-SE-M4M4-TT
BAR STOCK BALL VALVE: 2000 PSI 100 DEG F; MALE SOCKET WELDING BY FEMALE THREADED; MONEL BODY; MONEL K500'STEM; MONEL BALL; PTFE SEATING; FUGITIVE EMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE. TBV FE-4161-SWXSE-M4M4-TT
BAR STOCK BALL VALVE: 2000 PSI 100 DEG F;MALE THREADED BY FEMALE THREADED; MONEL BODY; MONEL K500'STEM; MONEL BALL; PTFE SEATING; FUGITIVE EMISSION; PTFE STEM SEALS; ROUND OR OVAL HANDLE. TBV FE-4161-SE-M4M4-TT
BAR STOCK BALL VALVE: 2000 PSI @ 100 DEG F;MALE THREADED BY FEMALE THREADED; MONEL BODY; MONEL STEM; MONEL BALL; ULTRAFIL SEATING; ULTRAFIL STEM SEALS; ROUND OR OVAL HANDLE; PREPARED FOR CHLORINE SERVICE AT FACTORY; TBV 4161-SE-M4M4-UT
GAUGE VALVE: CLASS 6000; NPTM BY NPTF (THREE MULTI PORT); ASTM B 164; MONEL ANNEALED BODY; SELF-ALIGNED BALL TYPE; UNION BONNET; MONEL K500'STEM; MONEL BALL; INTEGRAL SEATING; PTFE PACKING; ANSI B1.20.1. ANDERSON-GREENWOOD M5VHM-46
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
DO A 046783 CONFTDFNTTAl
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM VIB1000M01
SIZE
VIX6000M02
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 20 OF 21
DESCRIPTION
BAR STOCK VALVE: 1000 PSI 100 DEG F; MALE SOCKET WELDING INLET PORT; BY 1/2 IN NPTF (THREE MULTI PORT); MONEL BODY; MONEL KSOO'STEM; MONEL BALL; PTFE SEATING; PTFE STEM SEALS; ROUND OR OVAL HANDWHEEL. TBV 61-SW/SE-M4-M4-TT-L
TRANSMITTER MANIFOLD ASSEMBLY: 6000 PSI 200 DEG F; FLANGED; K MONEL; PTFE' PACKING. VALVE SHALL BE CLEANED, DEGREASED AND PACKAGED AT FACTORY FOR CHLORINE SERVICE. ANDERSON-GREENWOOD M4AVM
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
0O A 046784 CONFlDFNTTAl
PIPING MATERIAL SPECIFICATION DOW CHEMICAL USA LOUISIANA DIVISION
ITEM
NOTE <n>
SIZE
NOTE
PIPING SPEC CODE: L102 DATE: 02-11-94 PAGE: 21 OF 21
DESCRIPTION
CONTROL AND AUTOMATED VALVES: CONTROL AND AUTOMATED VALVES SHALL BE OF THE FOLLOWING SPECIFICATIONS:
CONTROL VALVES: TYPE: AS DETERMINED BY APPLICATION BODY: CAST 300 SERIES STAINLESS STEEL TRIM: HASTELLOY C PACKING: LIVE LOADED TEFLON SEALS/GASKETS: HASTELLOY C BELLOW SEAL FLANGE BOLTS: ALLOY 20 (CLEANED AND PACKAGED FOR CL2 SERVICE)
IF FISHER V500 VBALL VALVE IS USED THE.FOLLOWING MATERIALS ARE ACCEPTABLE
TYPE: FISHER V500 BODY: CAST 300 SERIES STAINLESS STEEL BALL: CHROMIUM PLATED CF-8M (CAST 316) SHAFT: 17-4 PH SS IN THE HI025 OR
SOFTER CONDITION SEAT/RING: 316 SSTL W/STELLITE 6 SEAT PACKING: LIVE LOADED TEFLON FLANGE BOLTS: ALLOY 20 (CLEANED AND PACKAGED FOR CL2 SERVICE)
AUTOMATED (ON/OFF) VALVES: TYPE AND SIZE ARE DETERMINED BY APPLICATION AND SHOULD BE SELECTED FROM THE VALVE SECTION OF THIS SPECIFICATION. THE VALVE SHOULD BE AUTOMATED IN ACCORDANCE WITH ENGINEERING PRACTICE L6C-8400.
LAST UPDATE: 11-10-93 NPL8087
PIPING SPEC CODE: L102
